Search Documents

Pongkor Gold Mines is one of seven units of production owned by PT Aneka Tambang (State owned mining company). The mine is located in the western part of Java Island, Indonesia. It is in the Bogor District and approximately 110 kilometres to the south of capital Jakarta. It is located in very steep hilly terrain intersected by many river valleys and the mine site is approximately 500 metres above mean sea level (see Figures 1 and 2 - Mine location map and picture)

Jan 1, 1997

By Rankin W. J

Increasing concern with the emission of sulphur dioxide from smelters and roasters has caused renewed interest in processes which can use waste sulphur dioxide, such as the sulphation of nickel laterite ores. The process described here proposes to by-pass the production of sulphuric acid and react laterite directly with a sulphur dioxide containing atmosphere. A thermodynamic analysis identified operating windows in which nickel sulphate forms while iron oxide (the major impurity in most laterite ores) remains stable. The initial assumptions included unit activity of all species except nickel oxide. The lowest possible nickel oxide activity (while maintaining selectivity) increased with increasing temperature, indicating that selective sulphation is favoured by low temperatures. The temperature of interest was found to be between 500 and 800¦C. Calculations show that a feed gas containing ten per cent SO2, five per cent 02, balance N2 requires a temperature greater than 650¦C for selective sulphation of nickel. Laboratory experiments showed that the assumption of unit activity of ferric sulphate was unrealistic above about 680¦C due most likely to the formation of solid solutions which decreased the ferric sulphate activity. Results are presented which illustrate the limiting equilibrium sulphur trioxide partial pressures at 700 and 730¦C below which selective sulphation occurs. Cobalt extraction was usually between 80 and 95 per cent under conditions yielding selective sulphation, whilst nickel extraction was about 50 to 75 per cent depending on temperature and choice of upper limit of iron extraction. An operating diagram is presented for a limonite ore and shows that the optimum reaction conditions are 680¦C and an input gas containing 20 per cent SO2. Under these conditions nickel, cobalt and iron extractions are 73, 95 and two per cent respectively.

Jan 1, 1996

CONTENTSIntroduction.Ore Bodies.Variations in Ore Dressing Practices.Stage I .Gravity Concentration for the production of a Lead Concentrate. 1909-1918.Stage Il Gravity plus Flotation Treatment for the production of a Lead Concentrate and a Zinc Concentrate. 1918-1929.Stage III All Flotation Treatment for the production of a Lead C~mcentrate and a Zinc Concentrate. 1930-1939General Summary - Stages I, II, III.Stage IV Gravity plus Flotation Treatment for the Production of a Lead Concentrate and a Zinc Concentrate. 1939-1947.1. General.2. Notes on Ore Dressing Practice.A. Gravity Section - Re~oval of Free Galena.B. Secondary Ball Mill Grinding Section. .a. Mineral Association.b. Composite particle problem.c. Degree of grinding required.d. Free Gangue Minerals in Table Tailing.

Jan 1, 1948

By Cocker J, Urosevic M

Seismic methods have become common for the detection of low-throw faults ahead of underground coal mining. Surface seismic methods cannot theoretically be used where dykes occur, because seismic waves transmit from the surface down to the seams, and reflect back to the surface. Consequently, where sub-vertical structure such as dykes occurs, the surface seismic method fails.The ability of seismic methods to image dykes depends on the geometry used, the dyke thickness and the seismic wave propagation mode in relation to dyke composition and internal structure. Surface seismic methods find it difficult to distinguish between faults/fractures and very thin dykes (1-2m in thickness) when the dyke's thickness is less than the seismic wavelength. Consequently, borehole seismic methods have to be used to detect the presence of such thin dykes.

Jan 1, 1998

This problem is seen as being central to a number of peripheral problems. Of these, the following are considered to be of major importance: 1. Reserves. Changes in Quality. Depths at which they occur. The effects of catchment and water storage areas. The effects of urban development. 2. Environment and the compat- ibility of mining and preparation of coal. 3. Transportation of Coal. J. tabour.

Jan 1, 1976

By D Henderson, K Howie

In 2005, Glass Earth Limited (GEL) commissioned two large area detailed airborne geophysical programmes in the Taupo Volcanic Zone (TVZ). In the first survey Bell Geospace Ltd of Scotland conducted an Air-FTG« (airborne Full Tensor Gravity Gradiometry) survey covering 2338km2 at 300m line spacing. The second survey by UTS Geophysics, Australia included detailed airborne magnetic, radiometric and digital terrain data capture covering 5341km2 at 150m line spacing.   From the detailed geophysical data collected it is possible to identify major deeply penetrative crustal structures within the TVZ, as well as define subsurface geological features, such as intrusive bodies and alteration zones. These major deep crustal structures are thought to have a controlling influence on the distribution of epithermal gold mineralising systems, and along the corridors defined by these deep crustal zones, the chances of discovery of an economic epithermal gold discovery are greatly increased.   In this paper GEL gives some examples of the application of its integrated data driven approach to exploration in the TVZ at both regional and project scale. The paper focuses on how GEL identifies regional scale highly prospective deep crustal structures. Then, using the Horohoro epithermal gold system as an example, we show how GEL applies innovative geological and geophysical data processing to model and understand detailed subsurface geology, focusing subsequent exploration to ensure the best opportunity for a new economic epithermal gold discovery.

Jan 1, 2007

By Dif A. E N, Abdalla MH

The effect of multiple tunnels /cavities on the stress and deformation field of the soil media was investigated by using a two dimen- sional plane strain boundary element model. The soil was considered as an elastic, isot- ropic and homogenous media. The interaction of two circular and parallel tunnels/cavities was investigated. Depth of burial, tunnel spacing and surface load width were the system variables considered. The results of this study indicated that the vertical displacements of the soil media increases by decreasing the distance between the adjacent openings, the interaction between the two tunnels/cavities can be neglected for K/D > 5, while the load width has a minor effect except in the dis- tance of D from the center line of the load and for a depth of 2D.

Jan 1, 1987

The recovery of Copper by solvent extraction was arguably the most significant hydrometallurgical development of the 1960's. However, only dilute solutions at relatively high ph. could be treated effectively. ICVAcorga introduced in the 1970's the much stronger salicylaldoxime based reagents, which resulted in a dramatic change in plant configurations. So for example plants which normally use 3 extraction stages and 3 stripping stages could be reduced to 2 + 2 staging or 2 + 1 staging, even for high copper tenors at low ph. Leach liquors up to 40 g A copper are being treated at some locations so that almost any copper bearing liquor can now be purified by solvent extraction. Following a considerable amount of research and development effort ICI/Acorga have made further significant advances in the application of copper solvent extraction. The first of these is in computerised flowsheeting. In conjunction with ICI's Process Technology Department, Acorga have developed the Minchem Computer program, which uses laboratory generated equilibrium data to facilitate optimisation of metallurgical operating parameters. The program can operate in two modes, prediction and assessment so that given suitable extract and strip isotherms plant performance can be predicted for a given set of conditions. Alternatively existing plant performance can be assessed rapidly and accurately, thus providing a valuable quality control tool. Pilot plant work can now be restricted to evaluation of the physical aspects of the SX circuits, and to looking for the unexpected. Secondly using the patented 5-Nonyl Salicylaldoxime in precise admixture with a number of carefully selected strip modifiers, the Acorga M-range has resulted. Reagent selection from these new extractants can now be based on how the reagent can alleviate the remaining problems such as hydrolytic stability, transfer of iron, and organic losses by entrainment which may be related to particular features of the operating plant. Thus the Acorga M-range has enhanced and significantly extended the use of solvent extraction for copper, whilst refinements in the processing of metallurgical data has considerably simplified circuit design and analysis of results.

Jan 1, 1989

By Sen A. K

The Chiria Iron Ore deposit falls within the well-known Horse-shoe-shaped Singhbhum-Bonai-Keonjhar belt in India, where most of the deposits supplying ore to various steel works of Steel Authority of India Limited (SAIL) and Tata Iron and Steel Company (TISCO) are located. With an estimated reserve of about 2000 million tonnes of ore (at 55 per cent Fe cut-off) spread over four contiguous blocks, it is the largest iron ore deposit in India and one of the largest in world. The present study is confined to only one of the four blocks of Chiria viz North Block, comprising an area of 2.11 km2. `Corporate Plan 2005' of SAIL envisages development of a large open cast mine at Chiria to meet its enhanced requirement of iron ore by 2001-02 AD.

Jan 1, 1995

By A Sinuhaji, H Kalangi, T B. Setyoko

Ore fragmentation at the DOZ block cave mine is highly variable, both as a function of rock type and column height of draw. Initially, the mine was constructed and equipped with limited capability to handle drawpoint oversize material. Significant issues with drawpoint availability and achieving overall mine production targets resulted. A suite of secondary sizing tools was added to the mine equipment fleet over a one-year time frame. Although significant oversize continues to be experienced, use of the correct secondary breakage tool for each particular oversize or hang-up occurrence has resulted in increased drawpoint availability, production rate, draw compliance, and operator safety. Currently, a range of secondary breakage techniques is being utilised to size material for delivery to the primary crusher. Run-of-mine material (3) is directly mucked to ore passes fitted with grizzlys that have one-metre square openings. Ore containing small boulders (>1 m3, 3) is loader-trammed to ore passes fitted with rockbreakers. Medium-sized boulders (>2 m3) accessible from the drawpoint are drilled with Sandvik Tamrock Commando drills. Boulders hung-up within the drawbell are drilled and charged with a Sandvik Tamrock Secondary Breakage Unit. Compacted, fine-grained muck is blasted utilising 55 mm cartridge powder concussion bombs.

Jan 1, 2005

By Marshall T. E, Finfinger G. L

Gulf Coast domal salt mining operations have had sporadic encounters with methane gas emitted without any warning. In virtually all confirmed cases, the methane was localized in methane enriched zones. In a few cases large quantities of methane were expelled rapidly with salt outbursts, resulting in dangerous methane concentrations. Estimates of methane liberated by face blasts in methane-enriched areas is needed in determining how much air should be supplied to the face for proper dilution. A relationship between the gas content of salt samples collected from the face and the amount of methane liberated would be helpful in estimating how much methane will be produced by a face blast. Little is known about the layering or stratification of methane in large area-low velocity airways. This publication reports on three tests conducted by the Bureau of Mines which monitored the immediate return air of four faces during blasting. The test locations were in a methane gas-enriched section that had previously experienced two large outbursts and many smaller ones. A comparison was made between gas content values of face salt samples from the dissolution test and the gas liberation quantities. The characteristic movements of the methane in a large room with low air velocities were charted. This will help to better understand the factors involved in proper placement of methane sensors as a warning system.

Jan 1, 1988

By Dunn P. G

The copper ore reserves at the Chuquicamata mine were re-estimated during March to June 1994, as part of a comprehensive audit of the mine's overall short- and long-term planning. The basic principles essential to all ore reserve estimates were implemented viz: 1. A detailed study of the geology, in this case particularly of the orientations of structural features of copper mineralisation and the subdivision of the orebody into geologically homogeneous sections, 2. the use of both drillhole and blasthole data sets, 3. statistical and geostatistical analyses of both data sets to model anisotropic spatial structures for all the geologically homogeneous sections, 4. block kriging using both data sets individually; and 5. a comprehensive validation of the block valuations to confirm the absence of global and conditional biases and to quantify the actual improvement achieved in the overall quality of the estimates compared to those executed on earlier techniques.

Jan 1, 1995

By Mogi G, Akaike A, Yamaguchi U

A new algorithm has been investigated for three-dimensional open pit designs to improve the dynamic cone approach which utilises the dynamic programming technique. The conventional dynamic cone method was improved by introducing examination processes: 1. whether any negative blocks are included in a unit cone or not; and 2. whether it is possible or not to leave the negative blocks unmined in the unit cone without disturbing the geometric condition imposed on the slope angle of the cone. The newly developed algorithm was applied to a large-scale open pit copper mine in a planning stage and the results have been compared with those obtained by the conventional methods.

Jan 1, 1995

Blast Engineers frequently use the terminology "the blast showed good heave", or even "the heave was better this time". It is reasonably obvious that "good" and "better" are not the best terms to use. It is also noted that any variation in the data can be misleading. The author proposes a more precisely defined and objective set of measures as tried and tested in a project in 1988. Simple objective measurements of a muck pile profile can measure 1. distance thrown 2. spread of material 3. heaping of material 4. skewness, or bias in the heaping 5. rotation of the mass This technique enables one to compare the profiles from different blasts without relying on subjective experience or judgement. Simple, artificial profiles will be presented to illustrate the problems of description; and then application of the measurement techniques to these profies will be discussed with physical interpretations. The mathematical techniques will be presented, and results of the application of the techniques to real data collected during research carried out at Baimsdale in Victoria, will be presented as illustration. The use of these techniques in mathematical modelling will be discussed.

Jan 1, 1990

This paper suggests the models for determination the optimum life of machines on the basis of sum and difference of investment and maintenance costs. The economic-mathematical models are based on complex percentage method taking into account the time factor of referring cost. The following strategies of maintenance policy have been considered in machines repair: a strategy without investment, a strategy with continuous investment and a strategy with step-like investment. The effect of value of investment in repairing and time interval of investment on optimum machine exploitation life has also been considered. An illustrative example is presented.

Jan 1, 2003

The main aim of the conference is to work towards improved useage of steelplant slags which have largely been considered waste mater- ials, This paper summarised investigations carried out on the suitability of air cooled blast furnace slag, blast furnace granulated slag and basic oxygen steelmaking slag as road base materials. All slag samples were obtained from the PortòKembla Works of Australian-Iron and Steel Pty Ltd. Since road making materials are increas- ingly being characterised by use of resilient moduli, the compressive strengths and resilient moduli were determined for road base of the following slags. 1 Air cooled crushed blast furnace slag 2 mixes of air cooled blast furnace slag, granulated slag, and lime 3 mixes of air cooled blast furnace slag,-granulated slag and basic oxygen steelmaking slag. Evaluation of a local dacite (dense medium grained igneous rock, classification rhyolite), generally considered an excellent road base course material, was carried out for use as a reference material.

Jan 1, 1979

By McCarthy PL

Widespread interest in reopening Victorian gold mines, regenerated by increased gold prices, has highlighted the technical problems prevailing. A combination of historical lease legislation, minimal recent mining activity, forms of mineralisation, high insurance rates and tortuous approval requirements for mining mean the potential investor assessing an old mine must address a wide range of technical problems. The requirements for establishment of ore reserves and attraction of capital for mine development are fundamental. Underground reef mining was historically generally on a small scale, and as mining on many fields ceased about the turn of the century, past geological and production records cannot be correlated to personal experience and comment. The impact of modern mining technology on future reef mining will be to reduce operating costs and significantly improve historic metallurgical recovery. Roth these are commensurate with increased capital costs. Workers compensation rates currently applicable in Victoria are many times higher than in other states, adding significantly to operating costs. Establishment of a pilot plant testing facility in central Victoria would provide an invaluable service in treating bulk samples essential for grade and recovery assessments of Victorian ores.

Jan 1, 1982

By Chitombo GP

The proposed guidelines on vibration limits that have been circulated by the Australian Environmental Council, demonstrate the need for an extensive data collection and evaluation program to avoid the enacting of abritrary and costly legislation. The operational or practical influence of blast design and overall economic implications of legislation which further reduces permissible levels of ground vibration are discussed. In a typical blasting operation, blast sizes could become smaller and blasting correspondingly more frequent to meet pro- duction demands. Blasthole diameters and charge lengths could be reduced, increasing drilling costs and associated labour costs. Blast size however, is frequently controlled by factors associated with machinery, grade control, pit control, stope size, production contract levels and other factors which cannot be readily changed for operating mines. Blasthole diameters are frequently deter- mined by existing drilling equipment, length of holes (depth of ore or stope size), geological structure and other factors which are not easily changeable. Typical large scale open stoping and strip mining opera- tions are analysed as case studies. The effects of extreme leg- islative limits and the corresponding operational changes with respect to variations in production costs are discussed.

Jan 1, 1987

The initiation of cast Pentolite primers by detonating cord has been examined by the combination of two different experimental techniques with computer simulation by the finite element hydrodynamic code DYNA2D. In the first type of experiment, the cord/primer system was placed in a water aquarium, and photographed using a high-speed image converter camera. This highlighted the emergence of the detonation front through the primer surface and the generation of shock waves in the surround- ings. Numerical simulation was used to interpret the experimental record, establishing where the cord had induced buildup to detonation inside the primer. The second experiment used the plate dent test, where the primer was placed in contact with a block of metal (here aluminium), with the resul- tant dent in the metal surface being a measure of primer output. Detailed numerical simulation of this test confirmed that the observed dent was caused by the development of a complex series of shock waves inside the Primer.

Jan 1, 1988

By S Chaudari, T Ren, T Harvey

Management of respirable dust on longwall face remains a challenging issue for mine operators, particularly for the new generation of thick seam longwalls. A fundamental understanding of the airflow behaviour around the shearer is critical for dealing with the dust control issue on longwall faces. Computational fluid dynamics (CFD) modelling techniques have been used in this study to conduct a detailed investigation of the air and respirable dust flow patterns around the longwall shearer. Three CFD models have been developed to represent different longwall cutting heights. The results of these modelling studies tallied well with field measured airflow data from different mines. The validated thick seam longwall face model was then used for detailed parametric studies to simulate the effect of various parameters and dust control concepts. The dust control options investigated include various spray configurations, shearer clearer, modified cutting sequences and shearer scrubbers of various capacities to minimise the respirable dust migration towards the walkway area of the longwall face. This paper presents a summary of the results of these CFD modelling investigations.

Jan 1, 2005