Search Documents

By X S. Li

The modern mechanical excavation machines have enough power for cutting hard rock. The ‘bottle neck’ which limits the use of machines for hard rock excavation is ‘cutting tool’. To cut hard and abrasive rock, CSIRO has been developing Super Material Abrasive Resistant Tools (SMART*CUT). SMART*CUT technology replaces the tungsten carbide (WC) tip of conventional pick with thermally stable diamond composite (TSDC) and attaches the TSDC tip to steel tool body with CSIRO worldwide patented bonding technology. This paper introduces the key features of SMART*CUT, compares its performance with conventional WC tipped tools, discusses the challenges faced by SMART*CUT and the further developments needed for successful application of SMART*CUT to mining industries.

Nov 22, 2011

By Z Li, Z Yan, M Yang

Recycled cement paste (RCP) is a kind of CaO-rich recourse, which is separated and recycled from waste concrete. Due to its chemical composition, RCP could partially replace lime as a flux and be loaded into electric arc furnace (EAF) steelmaking process. Rapid RCP assimilation and liquid slag formation have significant effects on EAF steelmaking process. In this study, the dissolution behaviours of RCP and lime at temperatures of 1400°C to 1500°C were investigated using static dissolution experiment. The dissolution rate, interfacial microstructure, as well as dissolution mechanisms were discussed. It was found that the dissolution rate of RCP was much higher than that of lime. RCP could be completely dissolved into slag in 60 secs at 1500°C. The dissolution rate of lime was in range of 3.910-4 g/(cm2ꞏs) to 2.610-3 g/(cm2ꞏs), while that for RCP was in range of 1.510-3 g/(cm2ꞏs) to 4.910-3 g/(cm2ꞏs). As for lime dissolution, a dense layer of dicalcium silicate (C2S) generated at the dissolution interface, and the diffusion of Ca2+ in C2S layer was the limited step for lime dissolution. Some of calcium ferrite could be observed at the interface between lime and C2S layer. As for the RCP dissolution, there is no obvious product layer of C2S formed at the dissolution interface, Fe2+ continuously diffused into RCP layer during the dissolution, and small amount of FeOꞏMgO solid solution generated and gathered at the dissolution interface. The dissolution rate of RCP in EAF slag was quite higher than that of lime, partially add RCP as flux in EAF could accelerate the slag formation process.

Aug 21, 2024

By R M. Smart, A T. Harrison

Backfill systems using unconventional cementitious binders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings æstableÆ slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 m high and the tailings were relatively high in pyrite. A GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shrinkage). The system used a slurry, but the addition of the activator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: stoping widths (mining heights) above 1.6 m; and shaft pillar removals in seismically active areas at the end of the life of the shafts. This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems). the acceleration (normally g, 9.81m/sec2) is increased to a significantly larger (but generally unmeasured and unknown) value, as shown in Figure 1.

Jan 1, 1998

By V P. Beskrovnaya

Tests for the development of a metals recovery technology from samples of a Russian gold-bismuth deposit were carried out. Gold, silver and bismuth assay reported 5.6 g/t, 3.0 g/t and 0.08 per cent, respectively. Two flow sheet options were pilot plant tested: gravity/cyanidation of gravity tailings with subsequent flotation of cyanidation/carbon-in-pulp (CIP) tailings, and gravity/flotation concentration with cyanidation/CIP of concentrates. Option 1 results showed lower gold, silver and bismuth recoveries (81.3 per cent Au, 55 per cent Ag and 74.0 per cent Bi) due to low flotation efficiency for cyanidation tailings. Therefore, a flow sheet involving gravity/flotation concentration to produce bismuth-gold concentrates (0.8 per cent Bi) with subsequent cyanidation/CIP was recommended. Gold, silver and bismuth recoveries obtained by this method to the combined gravity/flotation concentrate were 90.2 per cent Au, 83.3 per cent Ag and 80.2 per cent Bi of the ore, respectively. Overall gold, silver and bismuth recoveries were 83.0 per cent Au, 40.5 per cent Ag and 80.2 per cent Bi, respectively. Gold and silver recoveries to the cathode precipitate were 92 per cent Au and 48.6 per cent Ag (per operation). Reagents consumed for flotation were 0.1 kg lead acetate/t ore, 0.4 kg butyl xanthate/t ore, 0.2 kg T-80 frother/t ore, 0.02 kg sodium hexametaphosphate/t ore, 0.15 kg copper sulfate/t ore. Reagents consumption for cyanidation was 0.42 - 0.48 kg NaCN/t ore and 0.2 kg CaO/t ore. It was recommended to deliver bismuth concentrates after hydrometallurgical treatment to a smelter. Overall bismuth recovery including bismuth recovery achieved by pyrometallurgy was 60.0 per cent. However, it was obvious that delivery of bismuth concentrates to a smelter and their commercial treatment would be very expensive due to relatively high mass pull of bismuth concentrates (7.6 per cent of the ore weight). For this reason, thiourea leaching and hydrochloric acid leaching with subsequent cyanidation/CIP were investigated as alternatives to cyanide leaching. These two alternatives were proposed to enable optimal recovery of valuable metals from concentrates on-site. Recoveries obtained by thiourea leaching were 91.2 per cent Au, 90.5 - 91.9 per cent Bi and 77.0 - 78.1 per cent Ag. However, that method required considerable capital and operating costs. As an alternative, hydrochloric acid leaching with subsequent cyanidation was investigated. Test results showed improved gold, bismuth and silver recoveries, which were 94 - 95.9 Au per cent, 94 - 96 Bi per cent and 76 - 78 Ag per cent, respectively. Hydrochloric acid consumption was 100 kg/t concentrate or 7.6 kg/t ore. Current efficiency during electrowinning was about eight to 12 per cent. A recommended flow sheet involving hydrochloric acid leaching of concentrates, electrowinning of bismuth from solutions, recycling solutions after electrowinning and cyanidation of hydrochloric acid leaching cakes is described. Overall recoveries achieved by the proposed flow sheet were as follows: 84.8 - 86.5 Au per cent, 75.8 - 76.9 Bi per cent and 63.2 - 64.9 Ag per cent. Based on results from these tests, initial data for a bankable feasibility study and plant designing were developed.

Jan 1, 2007

Good morning ladies and gentlemen, and may I extend a particularly warm welcome to our shores to those of you who have travelled from overseas to attend this conference. I trust that you will find your visit to New Zealand both rewarding and enjoyable.   This is now my fourth appearance at a New Zealand minerals conference, the second of which has been jointly co-hosted by AusIMM and Crown Minerals. Since taking on the role of Associate Minister of Energy, I have had the opportunity to meet most of the industry players, and to visit a good number of the major mining operations. Through all of this I have become increasingly aware of not only how dynamic the minerals and coal industry is but also the array of factors that affect investment decisions in this business. Many of these factors, such as commodity prices and availability of investment funds, are determined primarily on the international stage. Others however, such as the allocation, regulatory and the fiscal regimes for minerals, are closer to home and are directly influenced by government policy decisions. I will talk more on what the government proposes in this area shortly.   But first, I would like to commend you all on your industryÆs continuing contribution to New Zealand Æs economy. 2004 has seen New Zealand Æs mineral and coal output top $1 billion for the second consecutive year. To put this achievement in perspective, it represents a staggering 47 per cent increase over the national output value recorded just five years ago. Notable contributions over the year came from gold which increased production to 10.2 tonnes (up nine per cent), ironsand production at 2.3 Mt (a 20 per cent increase), and industrial rocks and building stones (up six per cent) with rock for building, cement and roading showing significant rises on the back of strong regional growth and infrastructure development. Many regions, in particular Auckland, Bay of Plenty, Wellington and Southland, recorded significant increased regional activity with supply often struggling to meet demand. By contrast the coal sector had a relatively steady year with production remaining stable at just over five million tonnes for the second year running. Coal exports however are now consistently exceeding two million tonnes annually, generating export earnings of over $200 million, and could well be higher with rail capacity improvements. Many countries throughout the world are now importing our high quality bituminous coal for steel manufacturing and other industrial uses.

Jan 1, 2005

The difficulty in screening of ores when the moisture contents reach certain critical levels has resulted in mining circuits using wet processes for screening. While this has been acceptable in past years it is no longer acceptable in certain countries and where the mining company is looking to reduce its impact on the surrounding environment.   Various mining companies have been looking at ways to remove the need of using water, with all its inherent drawbacks and to be able to produce its desired products in a dry process.   This would have the benefits of less environmental impact and cost, (due to not requiring wet processing equipment), less power consumption (reduced equipment needed), no corrosion issues, no contaminated waste waters and reduced maintenance activities.   Until recently this has proven elusive or with technical restrictions with current available acceptable technologies for high capacity plants.   One major mining company began seriously exploring ways to overcome this dilemma so that they did not replicate their current ways of operating for their new expansion plans.   They partnered with Metso Minerals to undertake extensive groundbreaking laboratory test work and provide potential solutions as to how to solve this. The laboratory test work proved interesting enough to design, manufacture and test on the actual mining site a prototype screening machine in the circuit.   This break through in screening technology reduces the environmental impact on the area in which the mine is located by: eliminating the storage and use of water, reduction in energy consumption due to having no pumps in the plant, reduction in plant costs and the upstream affects on the environment process used to manufacture and ship the materials the plant structure is built from, and no large tailings dams to take up land space and affect the environment through groundwater/ water table contamination and the negative effects on animals and ecosystems Laboratory test were conducted and a full size machine was installed at the plant site along side conventional machines. The screen size (2.4 m wide x 6.1 long double deck) was determined by the size of screens currently in operation at the mine. The parameters that were explored were: types of screen surface (polyurethane, woven wire etc), types of screen motion (linear, circular or elliptical), angle of motion ( 40,45,55,60 degrees etc), and throw (amplitude), speed and 'g' force.

Jun 1, 2010

Vaal Reefs Mine annually produces some 75 tonnes of gold. Stoping operations, using a scattered mining method, are conducted on several reef horizons within Witwatersrand Supergroup metasediments of the Klerksdorp Goldfield. Current grades average 7.19 g/t Au over a 133cm stoping width. The reef horizons, of which the Vaal Reef is the most important, consists of 2.9Ga palaeoplacer deposits at the base of low angle unconformities. Typically, a reef comprises a mature quartz and chert conglomerate with a siliceous matrix and intergranular pyrite and carbon. Geologists are primarily responsible for underground mapping and supervising of drilling programs. To a lesser extent they are involved with sampling, grade control, ore reserve estimation, mine planning and rock mechanics. Due to a general decline in grades of gold mines, an escalation of production costs, and with the current weak gold price, it has become essential to improve production efficiencies. Consequently the role of the mine geologist has moved away from that of simply keeping the mining people "on reef'. Greater emphasis is being placed on refining geological models to assist in selective mining of the reef and investigations of secondary reef horizons are encouraged. Exploration within fault losses and re-evaluation of pillars is important, and geologists are becoming more involved with sampling and grade control exercises.

Jan 1, 1990

By Clappison D. J

Since its formation in Papua New Guinea and raising of A$2 million in 1980, Niugini Mining Limited (NML) has grown to a company capitalised on the Australian Stock Exchange at about A$350 million. In 1995 the company produced some 237 000 ounces of gold, 700 000 ounces of silver and nearly 5000 tonnes of copper from its operations at Red Dome, in North Queensland and San Cristobal in The Atacama Desert of Northern Chile. This production contrasts with Niugini Mining's first mining venture at Mt Victor in the Eastern Highlands of PNG which yielded 20 000 ounces of gold and 11 600 of silver between 1987 and 1989. Following the formation of an exploration joint venture in 1982 with Kennecott Explorations (Australia) Ltd, now a subsidiary of RTZ, Niugini Mining's early recognition of the gold potential of volcanic rocks at plate margins led to discovery of the Lihir deposit in July 1982. This deposit containing about 42 million ounces of gold in resources, is one of the largest undeveloped gold deposits in the world. Following raising of equity funds through the float of Lihir Gold Ltd and debt finance in 1995, construction of the mine at a cost of US$673 million is now underway with first full-scale production at approximately 600 000 ounces of gold per year expected in early- 1998.

Jan 1, 1996

The Rotary Kiln at TeKumi was commissioned in February 2002. The process involves burning limestone at 1000 - 11 000¦C to produce a burnt lime (CaO) product. This paper describes the design and installation of a trifoil system to improve the energy efficiency of the kiln. An energy balance showed that 32 per cent of the energy was being lost through the flue gases, compared to 5.8 per cent in shell losses and 2.5 per cent lost as heat in the product. The trifoil proved to be the best way to tap the energy from the flue gases. Drying tests showed that a trifoil improved the drying time of limestone by 37.5 per cent, compared to only 25 per cent for a lifter system. The trifoil system increases the surface area for heat transfer in a Rotary Kiln by 180 per cent. The overal energy efficiency of the Rotary Kiln was improved by 15 per cent, resulting in a 15 per cent increase in production and an 80¦C reduction in flue gas temperature. This has reduced dust build up in the ducting while reducing maintenance costs through a reduced fan speed. The trifoil hub was designed with tooths at the centre to prevent shifting. Each trifoil leg has an anchor block on the down side to prevent downward movement of the trefoil legs.

Jan 1, 2003

By A Garg

Squeezing can occur both in hard rock and in jointed rock mass as a result of over stressing. It is related to time dependent shearing, ie shear creep and is associated with the volumetric expansion (dilation) and radial inward displacement of the tunnel surface. While planning a tunnel in hard rock under a high cover of the order of 2 km it is desirable to identify the potential squeezing ground conditions and to select appropriate excavation technique and the support measures. There are several solutions to counter balance the squeezing ground viz over excavation of tunnel profile, assessing appropriate excavation technique, provision of a ductile primary support and time for providing tunnel lining. Low drivage rates and high cost due to support failures requiring rectification arising out of poor anticipation of tunnel closures and support pressures are major problems associated with tunnelling under squeezing ground conditions. Under squeezing ground conditions, the deformation will be gradual, therefore, in order to absorb deformations yielding supports are quite useful as primary support which provide a reliable low initial support pressure and permit uniform stress relief of the surrounding rock along with preventing rock from ravelling. The paper discusses the various factors which influence the selection of appropriate excavation technique and support measures in hard rock under squeezing ground conditions.

Jan 1, 1999

By De Cuyper J

Laboratory testwork has been performed on ancient residues from the cyanidation of a previously roasted gold-containing pyrite and arsenopyrite ore. By grinding to 95 per cent minus 60 microns, and after a strong aeration conditioning of the pulp, a gold recovery of approximately 67 per cent was obtained by cyanidation. This recovery was brought up to 80 per cent by leaching with thiourea, after a preleaching step with sulphuric acid under severe conditions of acidity and temperature. To avoid excessive capital costs bound to such processes, it was decided to investigate the possibility of applying flotation after grinding at a size similar or finer than the one used for the leaching tests. The method turned out to give interesting results because of the natural flotability observed at pH values lower than two for particles rich in gold present in the residue. After two cleaning steps, a final concentrate, representing around one weight per cent of the feed, was obtained with an approximate gold content of 350 g/t, representing a batch recovery of gold of about 50 per cent. Apart from sulphuric acid, whose addition was very high (flotation slurries at 25 g/l H2SO4), other reagents were not found necessary. Additional flotation tests were carried out to examine whether the recycling of the cleaner tails was justified but the gain observed appeared insufficient.

Jan 1, 1993

By Dixon D. R, Sparrow G. J

Pressure leach liquors from the pressure oxidation of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore were treated to remove iron, either by pressure oxidation (the Hematite process) or with particles of magnetite (the Magnetite process), followed by cementation of various metals with zinc dust to obtain a purified solution from which zinc was electrowon. Satisfactory iron removal was achieved by both processes after neutralisation to pH 4.5 or 5.5. Pressure oxidation of the liquor at 200¦C and 690 kPa oxygen overpressure, conditions similar to those of the Hematite process used in the zinc industry, resulted in the precipitation of the iron as hematite. With the Magnetite process, an iron hydroxide was precipitated onto magnetite at atmospheric pressure and ambient temperature and removed by a magnetic separation step. The performances of both these processes for the removal of iron are compared. It is concluded that the Magnetite process offers considerable cost savings. Other impurities, in particular arsenic, were also removed with the iron in both processes. Cementation at pH 5.2 and 85-90 ¦C with 3.5 g/L zinc dust reduced the levels of copper, cadmium, and nickel to a satisfactory level and subsequent electrolysis in a laboratory cell gave an acceptable deposit of zinc.

Jan 1, 1989

Environmental leaching methods such as the toxicity characteristic leaching procedure (TCLP) test or the ASLP test are used to assess wastes including mining and mineral processing by-products. These tests were initially designed as regulatory tests simulating conditions in a co-disposal municipal landfill waste facility and do not allow leaching performance to be predicted in site specific scenarios. Further, the assumptions underlying these tests tend to define worst-case scenario leaching conditions for by-products from the mineral industry disposed of outside a co-disposal scenario.   Recently some characterisation leaching test methods have been issued as ISO/TS standards (ISO/TS 21268-3:2007 and ISO/TS 21268-4:2007) that aim to define the leaching performance of soil type wastes and to predict the leaching performance of these wastes over long time frames. In this preliminary work these standards are trialled for by-products from the mineral industry and the quality of information that can be obtained from them compared to TCLP/ASLP tests.   Where clear comparisons were possible, the TCLP/ASLP tests were typically found to extract a similar, or often greater, amount of component than (i) tests conducted at the same pH but without the acetate buffer or (ii) for test conditions aimed at simulating long-term leaching in an eluate defined by the waste type. While further work is required, the preliminary results indicated that the tests may provide reliable long-term estimates of leaching performance of wastes in soil types of variable pH and provide a suitable basis for long-term planning for optimal waste handling, treatment or even re-use.

Jun 1, 2010

By Ormsby W. R, Nicholson P. M

Woodcutters is a polymetallic vein-style deposit hosted by sediments of the Palacoproterozoic Whites Formation which forms part of the sedimentary sequence in the central Pine Creek Geosyncline. Past production and identified resources total over eight million tonnes at 5.5 per cent lead, 12.1 per cent zinc and 110 gA silver. The local geology is influenced by Archaean basement highs; the Rum Jungle and Waterhouse Complexes. Unconformably overlying basement are interbedded clastic and crystalline carbonate units (Batchelor Group) representing cyclic changes in the depositional environment. These exhibit onlapping features with the underlying rocks. Sediments of the overlying Frances Creek Group suggest a quiet period during subsidence and subsequent increase in water depth (the carbonaceous dolomitic shales and the interbedded dololutites of the Whites Formation) followed by proximal uplift resulting in the inundation of turbiditic flows (Acacia Gap Quartzite). All of the Palaeoproterozoic rocks show evidence of being affected by penecontemporaneous, basement circling faults with steep dips. The stress regime during the deposition of the Frances Creek Group was characterised by alternating episodes of thrusting and transpression. Periods of relaxation also occurred. The compression resulted in major NS strike-slip (transpressional) faulting, en-echelon NNE trending folds and NW-SE tensional cross faults. Thrusting produced N-S striking, steep dipping reverse faults and a possible decollement immediately above the Batchelor Group. Relaxation is evidenced by the intrusion of lamprophyre dykes and dolerite sills (Zamu Dolerite). Mineralisation at Woodcutters occurred in faults within the Whites Formation, probably synchronous with deformation and the deposition of the upper parts of the Frances Creek Group. Greenschist facies metamorphism occurred as the rocks were further buried. Several massive sulphide bodies occur at Woodcutters. A number of features influence the location and shape of these bodies. They are: ò the N-S transpressional faults and in particular associated dilation zones; ò intersection of the N-S transpressional faults with the axial plane of the NNE trending Woodcutters Anticline; ò intersection of the N-S transpressional faults with the NW-SE cross-faults; ò intersection of dololutite rich units with the NS transpressional faults where local replacement takes place; ò thickening of the lithological units in the vicinity of the anticlinal axis; and ò the anticline doubly plunging to both the north and south. The mineralisation exhibits vein-like features as well as epigenetic textures. Its boundaries are sharp, its thickness varies rapidly down dip and along strike, and no alteration halo exists though stringer veins of quartz-carbonate-pyrite ¦ sphalerite/galena occur in close proximity. A number of sulphide mineral assemblages have been recognised, each separated by periods of deformation and partially replacing the earlier assemblages. Vertically continuous zonation patterns highlight the presence of rich galena-sphalerite-silver in zones of maximum dilation and pyrite-arsenopyrite-gold concentrated at the along strike peripheries. The genetic model proposed has the mineralisation occurring whilst the transpressional regime was active. It was deposited from the same fluid that elsewhere in the Geosyncline formed the stratiform deposits higher in the sedimentary pile. Hydrocarbons sourced from the organic-rich Whites

Jan 1, 1994

In general, modern mining companies all over the world have to face the same economic circumstances as any other part of the industry: considering the tough competition, production and haulage costs must be reduced permanently whereas productivity has to increase substantially in order to remain price-competitive. However, the imposed pressure also offers the chance for consideration of alternative mining concepts, the application of which can result in substantial cost savings and improvements in the quality of the mined material. As one of these alternative mining concepts, surface mining technology offers substantial improvements in productivity. It also influences aspects of haulage, such as safety and speed, in a positive way. The capability of selective mining ties in nicely with the production of small-sized crushed material, the granulometry of which allows the elimination of the primary crusher. Mine operators profit from reduced costs for the maintenance of their haulage vehicles due to reduced wear, a decreased likelihood of accidents and higher average transport speeds. Surface Miners can also be used to cut haul roads into virgin rocks and leave a clean and level surface behind, improving the quality of these created roads. Thus, it is even possible to use ordinary road trucks for transport in mines. The current paper outlines in detail the effects of the surface mining technology on mining and haulage aspects and reports on applications where substantial cost savings could be achieved due to the application of what is also referred to as æsimple mining processÆ.

Jan 1, 2003

According to the analysis of 126 mine gushing records and the relevant water supply and hydrogeologic condition, the gush can be classified into eight types;cave type,collapse -column. type, subterranean stream type, fault zone type, contact zone type, upper plate type, bottom heaving type and surface water invasion type. The formulae for counting the peak discharge of gushing point are further put forward in this paper.

Jan 1, 1988

By M G. Shaw, M A. Rhamdhani, S P. Singh, A R. Duffy, B Eisenbart, A K. Shukla, G A. Brooks

The field of astrometallurgy is a growing area of study. Metal production on the Moon is likely to begin in less than a decade as major space agencies such as NASA (National Aeronautics and Space Administration) and CNSA (China National Space Administration) are preparing to construct permanent lunar bases. The utilisation of regolith to generate oxygen and metals is expected to be important in the development of a sustainable lunar habitat. This paper provides an overview of potential metallurgical processing methods for lunar conditions, emphasising the impact of lunar factors on slag chemistry. The interaction between regolith and the extracted metals, as well as their impact on slag composition and refractory performance, are critical considerations in metal production on the lunar surface. The initial research on lunar metallurgical technologies is focused on oxygen extraction and Fe-Si alloys are reported as the by-products of these processes. This paper delves into the fundamental thermodynamics associated with the carbothermic reduction of lunar regolith. Thermodynamic analysis using the FactSage™ ver 8.2 software package indicates that the Fe-Si alloy can be produced as a metallic product from the lunar regolith at temperatures ranging from 1400°C to 1600°C under terrestrial conditions. However, under ultra-high vacuum conditions (3 × 10-15 bar) on the Moon, the required operating temperature for producing ferrosilicon would be significantly reduced. Thermodynamic modelling results indicate that under lunar vacuum conditions, Fe-Si alloys only exist as solid phases at lower temperatures below 650°C. At higher temperatures, both Fe and Si are expected to be present in the gas phase. In this work, the carbothermic reduction of the Lunar Mare Simulant (LMS-1) is conducted under terrestrial conditions. The findings indicate that the process can readily yield Fe-Si alloys with 7–10 wt per cent Si at 1600°C. Additionally, energy dispersive spectroscopy (EDS) analysis of the resulting Fe-Si alloy indicates the presence of phosphorus up to 1 wt per cent.

Aug 21, 2024

By A D. T Goode

Data Metallogenica (DM) is unique as a global mineral sample collection and deposit database with over 70 000 rock samples and a wide range of descriptive, photographic and measurement data. Subscribers have access to approximately four gigabytes of on-line data with many examples included on the public pages. DM commenced its life on the Pacific rim in 1971 and much recent growth has focused on countries of the Pacific margin, particularly Australia, Fiji, Chile, Indonesia and Peru. Approximately 600 separate deposits and mineral occurrences in this region are represented in DM. The sets of rock samples have been photographed at high resolution and included on the web site, together with unpublished descriptions, deposit cross-sections, bibliographies, field and mine photographs, petrology and reflectance mineralogy. Figures and abstracts from PhD theses are a new addition and the donation of proprietary databases by companies and individuals is an encouraging trend. DM increasingly is being viewed as an acceptable and important repository for æfragileÆ and irreplaceable personal and company data, it is also being recognised in its true light as a high level information system, not solely a collection of rock samples. Data Metallogenica is a not-for-profit venture of AMIRA International that requires self-funding from December 2004. Growth and development must be funded entirely out of subscription and sponsorship revenues because no government subsidy is provided. The Pacific rim is in the mainstream of mining and exploration activities worldwide and those involved have much to gain from a dynamically sustaining DM. The home page at www.datametallogenica.com contains much example data and details of subscription and membership rates.

Jan 1, 2004

By Hare S. M, Lumsdaine I, O&apos

Converter slag assaying 3.7 per cent Cu is produced by Mount Isa copper smelter at a rate of up to 180 000 tonnes per annum.Priority is given to the processing of ore, however concentrator capacity periodically exceeds that of the mine and the opportunity is taken to treat converter slag. It is processed in batch campaigns, typically through the Copper Concentrator, but the Hilton Concentrator has also been used. Slag and ore are kept as separate as possible, since each has an adverse effect on the flotation performance of the other.

Jan 1, 1993

This paper describes the application of the Total Productive Management (TPM) technique as a performance improvement initiative for a coal mining operation. It discusses the objectives of TPM, with the driver for improved production performance being the Overall Equipment Effectiveness (OEE) of the equipment or process, and with the development of "ownership" as the behavioral approach to equipment management and continuous improvement through cross-functional and area-based teams. It illustrates the concept of equipment management as defects management.The scope for application of TPM to the coal mining industry is immense. The harshness of the operating environment can be a major generator of equipment defects, and a current paradigm in the industry accepts these defects as an unavoidable outcome defining maintenance costs in this environment. However recent benchmarking studies have highlighted that maintenance costs per operating hour in some mining operations are more than double the vendor's estimate of "best practice". The paper refers to these studies which also compare maintenance costs of fixed and mobile plant and equipment to "best practice" outcomes in comparable process industries.

Jan 1, 1998