Search Documents

By J Pan, G Qiu

In this paper, an analysis is made of the present situation in the Chinese steel industry and its demand for iron ores. It is shown that the demand for iron ores has been growing substantially with the rapid development of the steel industry all over the world, especially in China. However, the iron ore market is currently in the situation where supply exceeds demand due to the economic crisis, with more investment in mines and less output of steel for several years ahead all over the world. Gigantic pressure is confronting the Chinese steel mills due to the too high and irrational price of iron ores. It is time to return the price of iron ores to a normal position much closer to their value. More attention has therefore been paid to developing low-grade and complex iron ore resources in China due to the irrational price of imported iron ores. More innovative mineral processing processes have been developed to tackle these complex resources. A systematic introduction to the development of beneficiation processes for low-grade iron ores is provided, including upgrading low-grade siderite, limonite, micron sized haematite and magnetite resources.

Jan 1, 2009

This paper traces briefly the reasoning which led to the decision to extend the existing internal shaft at the Rosebery Mine and to instal underground a larger winder (No. 2 Hoist) with capacity to handle all hoisting requirements to a depth of approximately 2,500 ft. on an incline varying from 83" to 55" to the horizontal. It then covers the specifications and selection of the winder, the design of the winch chamber, rope raise and bins, the excavation, support and lining of the chambers and the transport to site and installation of the machinery. Finally a brief description is given of the mechanical and electrical parts of the winder.INTRODUCTIONThe existing shaft winder on the internal inclined shaft situated on No. 8 Level of the Rosebery Mine had reached the limit of its capacity. Hoisting 21-ton capacity skips in balance, with a 13/16-in. diameter rope, it required four layers of rope on the 3 ft. 6 in.drums to reach the loading station under No. 12 level at a depth of 864 ft. (Fig. 1). This entailed heavy wear on the multi-layered rope and heavy stresses on the cheeks of the drums. Continuous working on three shifts was necessary to handle ore, men and materials, and a hold-up from any cause whatever meant an interruption to production on the lower levels of the mine. The maximum output of the hoist whilst hoisting from the No. 12 level loading station was 50 tons per hour. It was obvious therefore, that a larger winder was required if output was to be maintained.Diamond drilling had proved the existence of sufficient ore at depths well below No. 12 to warrant exploitation and a decision had to be reached on the means of hoisting this ore.

Jan 1, 1958

By E Widijanto, A Srikant

PT Freeport Indonesia operates a copper-gold mine located in the remote highlands of Papua, Indonesia, about 3500 km east of Jakarta. Currently, the district produces about 240 000 tonnes per day (tpd) of which about 45 000 tpd come from the DOZ Block Cave and the rest is mined from the Grasberg Open Pit. Over the next ten years, ore production from large block caves in the area is expected to reach about 200 000 tpd, replacing a large part of the production from the Grasberg Pit. Block cave mining alters the hydrological characteristics of the area being mined and when the cave expresses itself at the surface in the form of subsidence, it increases the entrapment area for surface water. Operating a large block cave mine in a region with an average annual rainfall of 5500 mm in steep mountainous terrain and complex geological and hydrological features presents a challenging scenario for dewatering or depressurisation of the area. The high rainfall infiltration and entrapment in stacked mines operating within an essentially single orebody, coupled with the presence of fine-grained and clayey material within the draw points of the block cave, creates mud rushes or wet muck spills, which can endanger the personnel and interrupt production. This paper outlines the problems caused by high water inflow into the DOZ Block Cave and the efforts undertaken to ensure the safety of the miners and continued achievement of desired production rates from underground mining in the district.

Jan 1, 2006

By N A. S Webster

The reaction sequences involved in the formation of iron ore sinter phases were determined using in situ synchrotron-based X-ray diffraction. Experiments were carried out using a synthetic sinter mixture containing 77.36 per cent Fe2O314.08 per cent CaO, 3.56 per cent Si.O2 and 5.00 per cent Al2O3 corresponding to a basicity of ~4. The alumina content represents the upper level of alumina concentrations measured in phases formed in industrially produced plant sinter. Data were collected during heating of the sample to 1350°C under an atmosphere of 0.5 per cent O2 in N2, equivalent to an oxygen partial pressure of 5 × 10-3 atm. This temperature was sufficientto ensure melting. Data were also collected on cooling of the sample back to room temperature to examine recrystallisation of phases from the melt.Results showed the sequence of reactions initially involved the formation of calcium ferrite phases C2F and CF. These subsequently reacted with the silica and haematite leading to the solid state formation of SFCA and SFCA-1. SFCA and SFCA-1 were the last phases to form in the system and were both stable up to ~1260°C. Above ~1260°C, melting of the SFCA phases and reduction of the remaining haematite occurred producing the assemblage magnetite + melt.During cooling, both SFCA phase types recrystallised from the melt initially coexisting with magnetite until secondary haematite formed. This is the fi rst study to demonstrate that both SFCA and SFCA-1 are precipitated from the melt during cooling of iron ore sinter. Future work will extend the range of compositions studied to examine the effect of basicity and alumina concentration on the phase assemblages as a function of temperature and oxygen partial pressure.

Jul 11, 2011

By Baafi EY, Chatterjee PK

The quality of mine planning decisions ultimately depends on reliable estimates of the characteristics of the orebody. The quant- ifiable factors such as grades or thickness can be estimated from field data gathered from outcrops or exploratory drillholes. Since outcrop data is necessarily limited to the periphery of a deposit, extensive drilling generally is required. This paper outlines a method for selecting the number and location of additional exploratory boreholes using an iterative procedure based on a mathematical optimization concept called fixed point theory. The method is illustrated through its application to an exploratory drilling program for a coal mine where optimized locations gave a lower estimate of regional and block variances than a manual Choice.

Jan 1, 1986

By G C. Snedden

Tandem row stator arrangements are common in the last stage of multirow, gas turbine compressors. Tandem row stators, or stator and de-swirler vane combinations are used to relieve the loading on the stator but ensure axial flow leaving the compressor. In this paper a standard 40” (1016 mm) ventilation fan in the Air Blow Fan’s range is modified to utilise the plate support struts on the barrel to relieve the aerodynamic loading on the aerofoil stator. Performance maps for both versions of the fan were generated using computational fluid dynamics and are compared across a wide range of rotor setting angles showing a clear advantage of approximately 2 per cent in efficiency for the tandem blade design. In addition, the area of high efficiency that represents the practically usable area of the map extends over a greater area in terms of flow rate and total pressure rise.

Oct 12, 2022

The Fosterville Goldmine in Victoria employs bacterial oxidation (BIOX« Process) to liberate gold from its flotation concentrate. Gold occurrence is primarily as submicron particles in pyrite and arsenopyrite and has been described as being in æsolid solutionÆ and therefore not amenable to direct cyanidation even with fine grinding. Once liberated by the oxidation process, the gold is then available for cyanide leaching. While the oxidation process is very effective, it has been found that a portion of the liberated gold can become suspended in the liquid phase in what appears to be a colloidal state. This liquid becomes a waste stream during washing of the oxidised solids and the suspended gold is therefore lost. This paper discusses investigations into the causes of the loss and also describes the successful use of quebracho tannin in reducing colloidal gold loss. Laboratory and subsequent plant trials, showed a gain of 2.6 per cent in overall gold recovery based on mill feed and waste stream data.

Jan 1, 2009

The Kiirunavaara apatite-magnetite orebody is about 4 km long and approximately 100 m thick sheet-like body, which lies roughly in a north-south direction and dips from the horizontal plane along its entire length, in towards the town of Kiruna. The origin of this orebody has been a matter of controversy, with both magmatic and hydrothermal origins proposed. Traditionally and for practical purposes this rich apatite-magnetite ore has been divided into two main types: low phosphorous ore (B-ore) and high phosphorous ore (D-ore). Further the low phosphorous ore is divided into the low alkali (B1) and the high alkali (B2) ore.

Jan 1, 2006

By P Mugebe, M Yahyaei, M S. Kizil, R Low

This paper seeks to establish an empirical relationship between the impact of mining technological innovation implementation and a company’s market value. The company’s market value is represented by its stock price. In a bid to ascertain the relationship, a stock price prediction model is sought to be established using the firm-specific factors impacted by the implementation of innovative technology. This work is performed under the watch of the prevailing macroeconomic factors. The background anchors in the understanding that the difference between the economic status of a mineral deposit and its uneconomic status lies in the level of mining technological innovation most prevalent at a given time (Hartwick, Olewiler and Preuss, 1986; Wellmer and Scholz, 2017; Wright and Czelusta, 2003). This is derived from productivity improvement, resulting in sustainable profitability due to technological innovation. Unfortunately, there is not an adequately established relationship that links this technological innovation impact to the share price performance of the mineral commodity company.

Sep 1, 2024

By Jankola W. A, Delong O. J

Historically, the silica content of zinc concentrates treated at Cominco's Trail Operations has been low. Silica in the roaster calcine seldom exceeded 1.5 per cent because of the low silica content of concentrate from Cominco's Pine Point mine. With the shutdown of Pine Point, alternate sources of concentrate were required and it was anticipated that calcines containing greater than two per cent silica (with excursions above three per cent) would have to be treated. Previous experience indicated that the existing leaching circuit could not tolerate such high levels. Therefore, a research program was undertaken to identify the key factors affecting silica precipitation; to compare different process alternatives; and to make recommendations for modifications to the existing plant. A project to modify and upgrade the leaching circuit has now been completed. Calcines with higher silica contents are successfully treated, but the upper limit of the circuit is unknown. The results of the research work will be discussed and the new leaching plant will be described. Recent operating results will also be presented.

Jan 1, 1993

By Verma UK

Mining for sand was active in South Delhi during the last four decades disregarding all norms of safety. The aim of the paper is to highlight what is proposed to be done for mining in Delhi. Apart from the damage to the landscape, the earlier operations gave rise to visual pollution to the scenic Delhi area and there is immediate need of land restoration and landscaping. Future mining should be planned so that the resultant land surface completely merges with the topography and gradually assimilates with the green belt. Restoration of old workings, land reclamation and details of plantation in old pit areas are included. The project also provides a demon- stration site to show the impact of eco-development leading to new legisla- tive measures, as it is in the Capital of India itself and therefore more accessible than any other area. What has been suggested for mining is not the latest and the most modern equipments from the Western point of view but the right equipment to meet the specific requirement of the country. Financial projections are included alongwith technical details of the project to show the benefits to the society. It is concluded that eco-development is essential for the mining in the Twenty- First Century.

Jan 1, 1986

By M Berner, N A. Sifferlinger, E Fimbinger

Today, the advance rate of underground roadway development by drill and blast operation is limited by the need to ventilate the toxic blast fumes after each cycle. In deep mines this usually is only possible during shift changes when the related mine sections are free of persons. This results in roadway development advance rates of 4 m per shift, or 12 m per day. For long roadways this is a limiting factor in mining development in deep mines. Companies like EPIROC, KOMATSU, ROBBINS and SANDVIK are making serious R&D efforts to disc-cutting mobile miners to overcome this bottleneck. However, today, the achieved advance rates are less than 12 m per day in hard rock. If we achieve full robotisation and/or teleoperation from a safe place for drill and blast operation of an underground roadway development section, we could eliminate this bottleneck. Poisonous blasting fumes do not affect robots and machines as long as these fumes do not create aggressive acids. If we can keep the blast fumes isolated in the roadway development section for the shift until the next ventilation opportunity (eg shift change or designated ventilation times), we can do the drill and blast cycle more often in a shift, which will significantly speed up the advance rate. This requires robotisation of all work steps in the section: surveying, drilling, charging of explosives, blasting, loading and transporting material, roof support, installation of infrastructure etc. Also, cache storage for the material is needed. Special care for the ventilation system to keep the blasting fumes under control in the section is necessary. The paper discusses the aspects needed to achieve this robotisation and the related technical and operational tasks.

Sep 1, 2024

The paper continues an account, begun in a previous paper, of experimental work carried out by the author whilst a member of the metallurgical staff at the Cockle Creek Works. The general method of the description of the plant and works practice adopted previously has been followed.The paper is a short account of the methods used in and the results of an investigation of the fume losses from the various parts of the plant.MEASUREMENT OF VOLUMETwo independent methods were used. The first depended on a number of pitot-tube measurements of velocity. These readings were taken in the stacks leading from the various furnaces at a considerable height above the ground so as to obtain as regular conditions as possible at the points where the readings were taken.Three openings were made in each stack and the pitot tube inserted into each opening in turn and readings taken at the centres of imaginary areas of equal size. The average velocity in the stack was thus obtained.After four tests had been made at the smelter stack, which removed the gases from all blast furnaces in use, the centre of velocity of the gases for each test was calculated and was found to be practically constant in position. The previous procedure was varied in subsequent tests on this stack by taking a succession of readings at the centre of velocity instead of at various points...

Jan 1, 1925

By A Lines

This paper addresses a gap in longwall multi-seam interactions and their predictions, providing a case study for future multi-seam operations for both anticipated conditions and a method for understanding the changes in stress regime. Multiple panels were modelled with the results analysed and compared to panel experiences to validate the parameters and properties. The software chosen (LaModel) is a numerical modelling package designed to model stresses and displacements on thin deposits. It utilises a displacement-discontinuity variation of the boundary-element method and has been used extensively throughout both the United States and Australia in multi-seam operations. Analysis of the results demonstrates a clear correlation with the above workings and regions of significant strata instability. This provides the opportunity going forward to analyse new models and incorporate into mine planning and geotechnical designs. Continuous site-based assessment should be undertaken at multi-seam operations to better understand and quantify likely vertical stress levels within the workings. With a detailed analysis of models prior to extraction and a review of models post extraction. Further research is required as LaModel is limited to vertical stress and it is likely that interactions impact both the horizontal and shear stress regime. 3-dimensional modelling could further assist in this understanding, combined with a thorough stress monitoring regime. CITATION:Lines, A, 2018. Modelling multi-seam interactions for longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 185–195 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By B Oostendorp, R van der Merwe, P

In order to assess whether polysaccharide depressants are strongly or weakly and reversibly bound to the surface of talc, a series of experiments was conducted on New York talc in which the floatability of the talc in a microflotation cell was determined. The talc was conditioned in solutions of carboxymethyl cellulose (CMC) or guar gum in 10-2 ionic strength Ca(NO3)2 or Mg(NO3)2. The talc was then washed with four successive aliquots of water, or cation solution, to try to remove the polymer and the flotation response of the talc was assessed. CMCs of different charge (DS) were used to assess the effect of charge on the strength of bonding. The results show that CMC and guar gum could be removed to a large extent from the talc surface by washing with water (the floatability was restored), however very little could be removed from the surface by washing with cation solution. The higher charge CMC was easier to remove from the talc planes in the absence of cations than the lower charge CMC. Thus CMC bonding to talc has been shown to be irreversible or very slowly reversible only if cations are present, implying that cations are necessary to keep the polymer bound to the surface of the planes to effect depression. The presence of ions in solution also had the effect of maintaining surface coverage of the talc by guar gum.

Jan 1, 2005

This report will differ slightly from the traditional scientific and technical discussions given at this type of conference. It will focus on the personal experiences and choices that I undertook when deciding on my graduate position and location after completing university studies. Throughout the duration of my course I had experience in both fly-in, fly-out operations in the Pilbara and residential operations in the West Australian Goldfields. These experiences, though limited, allowed me to explore the two different methods and their pros and cons, and consequently to make my choice for graduate employment. Throughout the duration of my degree I believed it was important to gain a basic understanding of the two methods, focusing on lifestyle and personal interactions. The decision that a residential site suited my personality and lifestyle then allowed me to refine my job applications to a more specific list of mine sites and companies, resulting in a residential position with BHP Billiton at their Iron Ore operations in the Pilbara, Western Australia.

Jan 1, 2005

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By Toussaint LF

A brief history of the mineral sands industry is given from a radiation protection standpoint, with gamma radiation and inhalation of radioactive dust being identified as the main sources of radiation exposure of persons working in the plants. The principal sources of gamma radiation exposure are identified and the history of early bagging methods is discussed. The concept of ALARA is introduced and the impact of the "bulka bags" (and more effective monazite storage facilities) are detailed as illustrative examples of dose minimization, together with the requirements for the transport of monazite. The dose from radiation received from inhaled dust is dependent on a number of parameters of the dust, some of which are not well known. ICRP 30 (1978) makes recommendations relating to the intake of radionuclides by workers. These recommendations are discussed with respect to the inhalation of dust containing thorium. The possible pathways of radioactive material throughout the body are also described. The effect of having parameters that differ from ICRP 30 is discussed and suggestions are made relating to measurements that can be carried out to more accurately determine these parameters. Since in some instances the exposures to dust yield personal doses which may exceed the annual ICRP 30 based limits, it is necessary to define more accurately parameters of the dust so as to determine more accurately personal Doses.

Jan 1, 1986

By S Jeon, K Haga, A Shibayama, L Godirilwe, C B. Tabelin, I Park, A Buronov

Open pit/underground mining and mineral processing can generate large amounts of waste that contains sulfide-type minerals such as pyrite (FeS2), and it can produce acid mine drainage (AMD) when exposed to oxygen and water. This highly acidic wastewater contains heavy metals and this is one of the most serious environmental issues after mining operations taking several decades to completely remediate with high costs. For green mining, the present study focused on the development of a recovery technique for gold from an eco-friendly solvent, thiosulfate, by utilising mine wastes, tailings. First, gold recovery experiments in ammonium thiosulfate system were carried out using model samples representatively present in tailings (ie SiO2, Al2O3, FeS2, Fe2O3, and Fe3O4). The results showed that gold recoveries were negligible when using Al2O3, SiO2, Fe2O3, and Fe3O4 while pyrite shows a recovery efficiency three-fold as high as the maximum recovery efficiency when using others. Subsequently, the study also addressed the identification of the recovery mechanisms and post-recover process. The results indicate that tailings can be sufficiently utilised for gold recovery in the hydrometallurgy process and a further sustainable process can be established.

Sep 1, 2024

By W Assibey-Bonsu

The paper provides a brief review of the multivariate uniform conditioning and the localised multivariate uniform conditioning techniques and presents a case study based on a porphyry copper gold deposit in Peru. Two other important scenarios have been investigated and will be particularly emphasised: The recovered selective mining unit (SMU)s depend on a combination of copper and gold content, which can be expressed by means of ænet smelter returnsÆ (NSR). Two approaches are compared. Firstly, the application of a composite cut-off on NSR on the joint distribution of each grade and the application of uniform conditioning to three variables is investigated, ie for the first approach NSR is used as the main variable. The second approach considers copper as the main variable. In the case of multiple domains the procedure used to apply the technique to process mixed panels is clarified and recommendations are made.

Sep 26, 2011