Search Documents

By B Reynolds

The process design for green- or brown-fields metallurgical plants typically starts with two fundamental elements: the detailed mass and energy balance and the plant flow availability. The detailed mass and energy balance is generally developed using process flow-sheet simulation software and represents the steady-state operation of the plant at normal operating conditions. The plant flow availability, also known as a range of other industry-specific terms such as ‘flow availability’ and ‘operating factor’, describes the ratio of plant production to the steady-state mass balance. These elements are then used together as the basis for equipment selection and design.Plant flow availability takes into account a myriad of production loss factors including planned and breakdown maintenance, feed availability and composition changes, variability in operational performance and the interaction of batch and continuous unit operations. The combined impact of these loss factors are complex and as such plant flow availability is usually derived using a top-down approach such as comparison to an existing operation, a group of similar operations or to an anecdotal ‘industry leading’ benchmark. These top-down approaches are fraught with risk however, as they cannot factor in changes to equipment selection, flow-sheet or plant operating philosophy, and can result in over-expenditure of scarce capital or shortfalls in plant production.The use of dynamic simulation to provide a bottom-up alternative to quantifying the plant flow availability in metallurgical plant design has been growing rapidly in recent years. It provides a technique to quantify the combined impact of the loss factors described here and a tool to support process design and equipment selection by facilitating a range of sensitivity and what-if analyses. This paper presents a case study of how dynamic simulation has recently been used to support the

Aug 8, 2011

By K Haga, G Danha, A Shibayama, L L. Godirilwe

The hydrometallurgical separation and enrichment processes provide an effective way to selectively recover metals from relatively dilute multicomponent sulfuric acid leach solutions. The multicomponent leach solution utilised in this study contained 0.3 g/L Cu, 0.34 g/L Ni, 0.13 g/L Co, and 2.96 g/L Fe, which was obtained after high-pressure oxidative acid leaching (HPOAL) of the copper-nickel smelter slag. The solvent extraction (SX), precipitation, and xanthate complexation processes were employed to recover and upgrade Cu, Ni, and Co from the leach solution. Batch SX tests were carried out using a countercurrent two-stage mixer settler extraction column, and LIX 984N (10 per cent v/v) as a copper extractant. Fundamental parameters influencing the extraction process such as pH, mixing speed, H2SO4 concentration, and organic/aqueous (O/A) phase ratio were investigated. For copper enrichment in solution, a combination of two extraction stages and two stripping stages were employed. Copper was successively separated from Fe, Ni, and Co under optimised extraction conditions (pH 2, 400 rev/min, O/A 0.25, and 20 min contacting) and stripping conditions (175 g/L H2SO4, 400 rev/min, O/A 4, and 20 min contacting). About 97 per cent of copper was extracted with low co-extraction of Fe, Ni, and Co of about 5.90 per cent, 1.47 per cent, and 2.53 per cent, correspondingly. A final Cu-rich solution containing 23 g/L Cu was obtained with a very low Fe concentration of 0.05 g/L. Additionally, for iron removal from the Ni/Co raffinate solution, more than 99 per cent of iron was precipitated at pH 4 by the addition of a calcium carbonate (CaCO3) suspension, with low co-precipitation of nickel and cobalt of around 3.68 per cent and 2.27 per cent, respectively. Furthermore, about 83.6 per cent of nickel and 99.4 per cent cobalt were co-precipitated from the solution by potassium amyl xanthate (PAX) solution at pH 6. The Ni and Co xanthate complexes were thermally decomposed and recovered as cobalt oxide (CoO) and nickel sulfide (NiS) solids.

Aug 24, 2022

By J Simpson, M Johnston

Recently Mount Isa Mines undertook a study to review the lead-zinc orebodies to extent of resource and reserves and determine the new life-of-mine schedule, as the Mount Isa and Hilton orebodies had not be reviewed for many years. Also, the recovered value of the Mount Isa, Hilton and George Fisher orebodies had been increased by major performance improvements in the lead-zinc concentrator. The Mount Isa Lead-Zinc concentrator processes fine-grained lead-zinc ore from the Mount Isa, Hilton and George Fisher orebodies. These orebodies have varying levels of pyrite and large variation in the grain size and texture of the galena, sphalerite and pyrite. This variation has a large effect on the recovery of the lead and zinc in the concentrator. Some ores achieve 90 per cent recovery at target grades, yet other ores are unable to achieve æsaleableÆ concentrate grade, with no metal being recovered to concentrate and therefore effectively losing the contained metal to the final tailings. Models were created to predict the metallurgical performance of these orebodies, to better reflect the variation that occurs. These improved metallurgical models and economic data allowed the determination of the Net Smelter Return (NSR) for each block in the geological block model. This NSR is the return to MIM of the metals contained in concentrate. The NSR was used as the cut-off grade criteria when determining the value of the ore. This formed the basis of the lead-zinc life-of-mine schedule and the optimisation of the lead-zinc business.

Jan 1, 2003

By Jones A

Today there is a vast amount of information available relative to the performance of tunnel boring machines, and associated systems. The data referred to here consists of project reports, manufacturer's equipment literature and papers concerning almost every aspect of the excavation process. Why is it then, that many projects that employ full face tunnel boring machines (TBMs), on average perform significantly less than the peak performances reported in this industry?

Jan 1, 1993

The introduction of a new mining method to Australia is not without its risks and challenges. This paper discusses the processes of planning a new operation, with particular emphasis on block caving and its Northparkes adaptation. As well as applying advanced technologies, here also is the opportunity to develop the art and science of block caving for its application to a wider range of geotechnical conditions than previously Envisaged.

Jan 1, 1995

By T Sasaoka, H Shimada

Mined-out limestone/aggregate quarries in Japan contain many high and enormous pit walls. Many precious resources are abandoned in these final pit walls. In addition, there are many mines which are located in or near populated areas in Japan. Utilisationof the potentially useful under- ground space at mined-out sites is a topic relevant to the practice of surface mining. This paper describes and discusses the concept of underground space utilisation and tunnelling systems, referring specifically to geotechnical/ tunnelling parameters.

Jan 1, 2008

By Remilton D, Raston GR

The low price of nickel which has prevailed since 1982 has dictated that unit production costs must be minimised. Early in the crisis, a decision was made within Western Mining Corporation to reduce unit costs by increased rates of production, not by a significant reduction in manpower. This paper details developments which have taken place at Kalgoorlie Nickel Smelter to enable the higher production rates to be achieved, or to increase energy efficiency. It is significant that most developments were achieved without the need for capital expenditure.

Jan 1, 1985

By D I. Cliff

The loss of 11 miners in the 7 August 1994 Moura No.2 Underground Mine Disaster was the catalyst for major change in the way safety was managed in the Australian Mining Industry. The impact was felt across all sectors not just underground coal. It was the catalyst for the overhaul of the regulatory frameworks, moving away from prescription to management systems and risk management. This had a substantial impact on the way not only the industry operated but also on how the regulator functioned. It heralded the introduction of competency-based training across all levels of the mining workforce. Since that time major improvements in safety performance have occurred. However, hiding within the statistics are some disturbing trends. This paper aims to analyse the progress made in the past 30 years and identify the current and emerging issues. Automation is bringing major production and safety benefits, but at the same time other factors such as the reduction in workforce numbers and ever-increasing production pressures are leading to high turnover rates. This in turn causes to a loss of experience and expertise. In addition, and of particular importance, is the recognition of psychosocial wellness on workforce safety. Many of these factors are not unique to the mining industry however they may be exacerbated by the scale of mining, the remoteness of the mines and family unfriendly mining rosters.

Apr 16, 2024

By T Ladinig

Raise caving is a novel cave mining method, which has been proposed for mass mining at increasing mining depths in LKAB operations. The method makes use of the raise mining technology and an active stress management approach. For the implementation the method is split into two phases, namely a de-stressing phase and a production phase. In the de-stressing phase, a slot-pillar system is established. The purpose of slots is to provide stress shadows and the purpose of the large pillars is to control stress and seismicity. The production phase follows after the de-stressing phase. Required infrastructure in the production phase is developed delayed in stress shadows and bulk extraction takes place in de-stressed zones. Eventually the pillars crush and they are extracted in the production phase. A comprehensive research and development program has been launched to develop the raise caving method towards implementation. As part of this program a full-scale test site of raise caving will be conducted as well as raise caving operations are planned for depth extensions in LKAB mines. This paper discusses the design of raise caving operations in practice at the LKAB mines. In particular, the purpose of the paper is to focus on requirements for the development and design of a raise caving operation. The development of raise caving is discussed from a systems engineering perspective as well as from a management perspective. The functional requirements in the destressing and production phase are outlined and discussed in the paper. The discussion is on basis of the main elements of the raise caving system, such as slots, stopes, pillars and infrastructure. Critical rock engineering design requirements in the de-stressing and production phase are highlighted and dependencies between individual main elements are identified. The analyses show that pillars are especially important for the success of the mining method. Overall, the analyses show that raise caving is a complex system and that its development demands a multidisciplinary approach.

Mar 29, 2023

By L Chaffey, M Buckland

The minerals industry has enormous potential to positively contribute to sustainable development and many leading companies have concluded that their long-term success is directly linked to their ability to leave a lasting positive legacy. While there are many examples of success, there have been failures as well and much work has been done in recent years to define the role of the minerals industry in sustainable development and identify the key elements for success. In the past, our sector could point to the taxes and royalties it paid, the exports it generated and employment it created and felt confident that its contribution would be recognised and duly acknowledged. This is no longer the case. Critics of the industry have highlighted resource-rich countries that have failed to capitalise on their resource wealth and have arguably lower standards of living than their resource-poor peers û the æresource curseÆ hypothesis. Recent research has done much to clarify the factors that contribute to a countryÆs success or failure and all stakeholders in the industry now need to include these learnings in their approaches going forward. We know that our long-term success relies on embedding a company- wide approach to sustainable development into all aspects of our business operations. In this paper we highlight BHP BillitonÆs experience in the development and implementation of policies and systems designed to enhance our contribution to sustainable development. We detail the business drivers for excellence in this area and the key external codes and initiatives that have shaped our approach. The values-based BHP Billiton Charter, Sustainable Development Policy and associated Health, Safety, Environment and Community (HSEC) Management Standards are central to our approach. Implementation is reviewed through our HSEC audit program. One area in which we have placed particular emphasis is our approach to community development. BHP Billiton has a corporate target to contribute one per cent of its pre-tax profit on a three year rolling average to voluntary community programs. As our profit stream has increased with the minerals boom this is approaching an A$100 million commitment. In our paper we detail how we are working to ensure we maximise the value of this contribution for our communities and our shareholders.

Jan 1, 2006

By J Jones, J Blunt

"The requirement for environmental approvals and associated environmental impact assessments (EIAs) is now commonly regarded as a key milestone and body of work during project development. EIAs can be undertaken at various phases during project development, generally either:\ during the scoping or prefeasibility studies, where limited project information is available and the mitigation and management measures of the EIA become a set of criteria and commitments that control project design during the feasibility study, as an iterative approach whereby mitigation and management measures are developed through an integrated process with the engineering team, and measures are included in the feasibility study cost model following the feasibility study, where detailed project design information is available, the cost model is complete, and the EIA is an assessment of a fixed project with limited opportunities for mitigation and management measures to be integrated into engineering design. This paper investigates the advantages of integrating EIA into life-of-mine planning during the feasibility study phase, using the Tampakan Copper-Gold Project (the Project) as a case study. The Tampakan Project is located in the Philippines on the southern island of Mindanao. The Project involves the proposed development of three main areas of infrastructure:a large-scale, open pit copper-gold mine and associated mine site infrastructure (including tailings and mine waste storages, fresh water dam, concentrator, etc) a power station, port and filter plant (PPFP), located approximately 60 km from the mine a pipeline and transmission line linking the mine and PPFP sites.Examples of engineering measures developed through an iterative process to mitigate and manage predicted environmental and social impacts include design of water management infrastructure, modification of the disturbance footprint (eg roads realigned to avoid critical habitat) and realignment of project infrastructure to minimise impacted water catchments.CITATION:Blunt, J and Jones, J, 2012. Integrating environmental impact assessment into life-of-mine planning, in Proceedings Life-of-Mine 2012 , pp 143-152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

Traditional in situ fan flow test methods under accepted standards require determinations to be made of both static pressures and total pressures during testing. This is to determine the resultant velocity pressures, which are vital in the accurate determination of the final fan airflow. These crucial velocity pressure (Vp) determinations are normally determined using simple manometric instrumentation such as an electronic manometer or an inclined liquid filled manometer. There is relatively little noise or fluctuation in the static pressure determinations and they can be quite easily and accurately recorded. There is almost always considerable fluctuation in the velocity pressure determinations though due to the highly turbulent and irregular velocity profile normally found in such in situ installations. This velocity turbulence means that the recording of such data is subject to random human error as the observer tries to average such fluctuations mentally during the observation period. Worse than this, and in the extreme, the recording of such velocity pressure data could actually easily be misreported if, for some reason, persons chose to do so.The author has devised a field method using highly accurate quartz crystal logging barometers to objectively record these velocity pressures. The method eliminates the ability to either mistakenly or intentionally misreport these crucial velocity pressures and is carried out in parallel with the recognised methodology, so result comparisons can be drawn. As such, a far greater level of confidence can be achieved in the final flow performance results than using the traditional more subjective method. Further to this it is difficult and almost impossible to refute the results using this ancillary substantiation method.The accurate determination of fan flows due to the impost of the carbon tax has taken on much more significance given the financial impacts in Australia at this time. The methodology detailed herein can be applied equally for both fan flow compliance testing and the verification of mine airflow data for greenhouse gas emission evaluations.The paper utilises the results of one 24-point pitot traverse to demonstrate the various findings. These include the very wide range of velocity pressures, which were logged at most of the measuring stations. It also illustrates how the method is utilised and compares the results derived from both this method and the more subjective traditional method along with the benefits of logging the velocity pressure results during the testing process.CITATION:Rowland, J A, 2013. Removing some subjectivity from traditional BS 848 and ISO 5802 in situ fan flow tests, in Proceedings The Australian Mine Ventilation Conference , pp 155-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By P Wilson

The Mt. Wright Underground Mine is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. The establishment of the world’s first Sub Level Shrinkage (SLS) mine from a tradition Sub Level Open Stoping operation has proven to be a geotechnical challenge which has required tailored solutions to overcome unique issues. This paper will be broken into two distinct sections that will outline: a brief overview of the mining method and how the SLS method was chosen; and how the SLS is managed and key geotechnical learnings. The story of the world’s first SLS originated from the need of a bulk mining method to ensure the viability of Mt. Wright into the future. Traditional bulk mining methods such as; Block or Sublevel Caving were originally ruled out due to the low natural ‘cavability’ of the orebody and the proximity of the orebody to existing major infrastructure (Decline, Ventilation Rises and Egresses). The first section of the paper will outline the key geotechnical information that helped decide the SLS method in addition to how continuous backfill influenced the design. The second section is intended to address issues that the geotechnical engineers encountered since the inception of the SLS. The feature topic of this section is mining induced stress. Like most bulk mining methods, Mt. Wright had success when the production front was running parallel to the stress (production front being ‘shadowed’ from the stress). This was until a design change, forced by a splitting ore body resulted in this shadowing effect becoming harder to achieve. As a result, rehabilitation and production hole re-drilling become a regular occurrence, which teamed with a strict set of access controls made the production cycle longer and harder to complete. CITATION:Wilson, P, 2018. Mt Wright – geotechnical learnings from a sub level shrink, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Glassock C. D

Most Australian mining projects are becoming smaller, more remote and with lower grades of ore. Their small size has been making it harder for mining companies to absorb the large infrastructure costs. This has forced companies to reduce those costs in every way they can. Social factors, environmental groups and even tax laws have added other pressures to force down the infrastructure costs for remote projects. For the last ten years, the downward trend in costs has been marked. It seems certain to continue for years into the Future.

Jan 1, 1997

Longwall mining operations have been in place in Australia since the early 1960s. This mining method is currently used to extract the bulk of coal obtained from underground mines in Australia (CSIRO, 2010). Despite the high tonnages extracted the expected utilisation of much equipment remains relatively low. To some extent this level of utilisation is influenced by the variability in conditions inherent in the mining process. This variability in production rates presents challenges to those attempting to design a coal clearance system. The difficulty is to design a system that has sufficient capacity to support production, without over capitalising or incurring high operating costs. The need to allow for a series of largely unplanned events in the design of a coal clearance system makes simulation modelling an ideal technology to employ. Simulation modelling is a methodology that allows a system with interacting components to be modelled over time, while explicitly taking into account unplanned events that may disrupt operations.This paper discusses how dynamic simulation models have been used to assist in the design of coal clearance systems. Typically this type of modelling has been used to look at the likely profile of production rates from the Longwall shearer and to determine how well various proposed combinations of belts, bins and stockpiles would support production.

Sep 26, 2011

By D R. Seaman, R P. Tooher, B A. Seaman

"Several mine scheduling tools exist for use in optimising and scheduling the reserve according to in situ value. These tools generally value the ore on a per block basis according to regressed recovery models based on ore grade and type. It is then the task of the plant metallurgist to ensure that these ore blocks are fed to the plant in a manner that satisfies the prevailing plant constraints. This task is often completed in complex Excel® spreadsheets that are modified over time with factors applied to account for plant modifications or limitations.It is the authors’ experience that this approach is difficult to audit and replicate in a consistent manner. Furthermore, operational decisions, such as primary grind size or autoclave oxidation are made on the metallurgist or managements’ perceived optimum value and does not necessarily represent a cash flow based optimum.Many processing plants contain multiple internal constraints. As ore feed grades and properties change over the life-of-mine (LOM), processing-bottlenecks shift from one unit process to another and different operating strategies need to be adopted to maximise cash generation from the process.This paper presents a unified optimisation approach to scheduling ore based on a circuit mass balance to describe the process plant with individual models for each significant unit operation. The approach allows for optimisation over multiple input variables and the inclusion of linear and non-linear constraints.This optimisation process has been applied to different complex gold operations. The end result is an automated scheduler that selects the optimum blend of ores as well as plant operating conditions that satisfy all internal plant and shutdown constraints while maximising the objective of choice (metal production or cash flow). The models are also valuable for evaluating expansion or debottlenecking opportunities of individual processing units. These models are coded in Matlab® R2016a provided by MathWorks®, and can be deployed to end users in a compiled version with significant savings in time to run different scenarios over the Excel®-based systems.Citation:Seaman, D R, Tooher, R P and Seaman, B A, 2016. Optimisation of Complex Gold Processing Plants with Multiple Unit Operation Constraints - the Newcrest Planning Scheduler, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Y Zha, J L. Walshe, A Ord, N J. Archibald

The purpose of this paper is to discuss the concept of Geodynamic Modelling as an exploration tool and to provide a specific example, namely, the Century Zinc deposit in Northern Queensland. Geodynamic Modelling is an attempt to become more quantitative in the way we develop exploration models. It is a systems approach to ore genesis which examines the complete four-dimensional mineralising system of interest, rather than individual site specific ore deposits. The goal is to establish a predictive capability that enables the explorer to predict grade, tonnage, mineralogy, alteration patterns and precise location of a potential orebody given a particular exploration model. The process consists of two well-defined stages: firstly, a æsoftÆ modelling stage where all available data on lithospheric architecture, geodynamic history, fluid chemistries, fluid flow mechanisms and mechanisms of metal transport and deposition are collected; and secondly, a æhardÆ modelling stage where the system is modelled using fully coupled deformationûfluid flow-thermal transport-chemical reaction computer codes. In the case of the Century Zinc Deposit we point to its existence on the boundary between two fundamental blocks of Proterozoic mantle lithosphere. This boundary has controlled Pb/Zn mineralisation in Northern Australia from the Proterozoic through into the Paleozoic. Detailed thermal, chemical, fluid flow, deformation modelling of the Century System points to an origin involving mixing of crustal oxidised fluids bearing zinc, with reduced fluids bearing H2S and CO2 from the lower crust or mantle. We use this modelling to define critical exploration criteria for another Century type of deposit.

Jan 1, 2000

By M Edhammer

In 2007, Atlas Copco introduced an integrated tunnel scanner/profiler. The tunnel scanner, which is integrated into the control system, is mounted on the drill rigs, and replaces the previous variants of non-integrated scanner equipment. The Atlas Copco Tunnel Profiler, which is the name of this system, is currently being used by several contractors and mines on various projects in Scandinavia, Finland and Australia. Atlas Copco Tunnel Profiler can scan a tunnel of 65 m2 in just five minutes and is integrated with the computerised control system for the drill rig. This integration means that the results of scanning are immediately available for analysis on the computer screen both in the drill rig and in Tunnel Manager; a software for tunnel and drift planning.In 2008, a method was introduced for locating the drill rig with a total station navigation (TSN) system, integrated into the control system. TSN systems are used by a number of contractors in Scandinavia and Finland, as well as elsewhere in the world. Using a TSN for navigation is in itself not new, but when this is integrated with the control system it provides the opportunity for individual drill rig operators to use this method, without the direct assistance of a surveyor. TSN gives a very precise indication of the drill rig’s position in relation to the tunnel design. An accuracy of ±1 cm compared with the ±10 cm which is normally obtained with the traditional method using tunnel laser and sight plates on the drill rig’s feeder. The closer a tunnel is blasted to its planned profile, potentially the more is saved in terms of less shotcreting, extra rock bolting and other corrective work. A better quality tunnel is the key to better overall economy and today’s technology makes it possible to achieve that goal in every type of tunnelling and mining project.In addition to total station’s ­navigation and Tunnel Profiler, the concept of ‘high precision tunnelling’ also includes:•Software tunnel planning: Tunnel Manager, Tunnel Manager Pro and Tunnel Manager Measure while drilling.•Measurement While Drilling (MWD)collects the various drilling data and the interpretation of these for the early identification of variations in the rock.•Rig Remote Access (RRA) is a support for wireless or wired communication between drill rig and planning office. The result is being able to send planning data to the drill rig and to simultaneously have the facility for logged files to be sent from the rig to the office. There is an option of an external computer logging in to the drill rig’s control system to view menu screens and settings, and remotely troubleshoot and plan appropriate action.

Mar 21, 2011

By H M. Parker, G Verly, T Postolski

Assessing the uncertainty and risk in mineral resource estimation is required for best practice and is implied by the public reporting codes in the categorisation of mineral resources and reserves. One industry best practice is quantifying the risk on future production for a given period, which can be done using two geostatistical approaches: conditional simulation and drill hole spacing studies based on estimation variances. Conditional simulation can provide a more complete and flexible answer to the problem, but it takes a fair amount of time to complete. Drill hole spacing studies are simpler, faster and can provide reasonable assessments of mineral resource uncertainty.This paper is a presentation of the principles, theory and practice of drill hole spacing studies. Various types of risk assessment are considered. Difficulties encountered in practice are discussed, and solutions are proposed. The important parameters impacting the results are reviewed. Examples of results and sensitivities are shown.CITATION:Verly, G, Postolski, T and Parker, H M, 2014. Assessing uncertainty with drill hole spacing studies – applications to mineral resources, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 109–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By S Thomson, G Rigby, J Norgard, D Wilkinson

Bulk explosives provide the energy to move a rock mass and reduce it to an optimal size (fragmentation). The intensity of energy needed depends on several factors including a customer’s geology and end objectives. An energy mapping tool has been developed to help customers to determine their bulk explosive needs based on these objectives.At one end of the energy map dealing with high-energy products, a new range of bulk explosives products for surface mining have been developed. With these products, it is possible to provide blast designs with up to nearly triple the relative bulk strength (RBS) of ANFO, and address primary focus areas for mining operations, including the reduction of drill and blast costs, improvements in production rates, better face advance through improved broken stock management, better drill productivity, improved milling efficiency and lower energy costs in surface mines.In this paper, field trial results from the first level of new high-energy products are presented. These products have an RBS 2.25 times that of ANFO. Industry variations of a smaller diameter (89 mm) pumped product for civil quarrying applications, and for large diameter (311 mm) hard-rock metalliferous mines are presented. For both cases, the run-of-mine fragmentation levels obtained with the new bulk explosives are contrasted with the fragmentation profile generated with the currently accepted product range applied in similar geological conditions. The new products show increased fragmentation across the measured size distribution, with reduction in P50 values of 20 and 37 per cent over the currently used product for the 311 mm and 89 mm diameter blastholes respectively.CITATION:Wilkinson, D, Rigby, G, Norgard, J and Thomson, S, 2015. Higher energy bulk explosives – matching products to rock types using an energy map concept, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 579–584 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015