Search Documents

By S Gezgin, F Beckstein, M Müller, D Rapp, D Sergeev, J Qi, A Lichtinger

Salts and their mixtures play an important role for industrial and energy sectors, eg metallurgy, biomass gasification and combustion, nuclear and solar powerplants and electrochemical processes. Depending on the composition of salts (eg Li+, Na+, K+, Mg2+, Ca2+ // NO3-, F-, Cl-, CO32-, SO42-, etc), the temperature range for different applications can vary starting from room temperature and going up to 1500°C. For the proper design and modelling of heat exchangers and other equipment, it is necessary to have reliable and validated data sets of thermophysical properties. The 50 mol per cent NaNO3 – 50 mol per cent KNO3 salt mixture as a well-studied composition was selected for validation of relevant thermophysical properties (heat capacity, enthalpy of phase transitions, thermal expansion, viscosity and thermal conductivity). To study these properties of the liquid phase, special crucibles and approaches should be implemented. Verification of these crucibles for different methods (differential scanning calorimetry (DSC), thermomechanical analysis (TMA), laser flash analysis (LFA) and rheometers) has been performed. The low thermal conductivity of salts is one of the main problems in implementing latent heat storage. In this project, the authors intend to develop a fundamental solution to this problem using chemically bonded metals with salts. These are known as metal-salt solutions. To fit the main parameters of new phase change materials to the requirements of thermal energy storage, a wide variety of possible combinations should be considered. CALPHAD modelling is used together with thermal analysis for the development of a consistent thermodynamic database including chloride salts (Li, Na, K, Mg, Ca // Cl) and corresponding metals (Li, Na, K, Mg, Ca). The results of the study of quasibinary and multicomponent metal-salt (eg Mg-KCl and Ca-KCl) systems as well as the selection of suitable crucible materials and challenges by studying of these systems will be discussed.

Aug 21, 2024

By D Olwagen, C Stanton, J Gerber

From December 2013 to February 2014 the Southern Middleback Ranges magnetite concentrator went through a successful optimisation process that included the installation of extra grinding power to treat a wider range of ore types. After the initial improvements, sampling surveys were conducted to identify the mineral deportment through the concentrator. Samples collected during the survey were analysed using X-ray fluorescence, quantitative X-ray diffraction and QEMSCAN™ to cross-validate the analysis. Certain streams were also put through a laboratory-scale Davis Tube Recovery washing process to produce clean concentrates for analysis. The QEMSCAN™ analysis identified various metallurgical characteristics (mineral association, particle sizes, grain sizes, particle densities, etc) and these were evaluated for each separation and comminution stage to both understand the processes involved and identify opportunities for improvement. Key findings from the investigation indicated the importance of understanding the elemental deportment of target elements throughout the various minerals. The standard practice of tracking iron deportment through assay provided misleading results on losses to tail through the plant. The investigation provided insight into both wanted and unwanted minerals and the efficiency of each separation stage. The efficiencies of separation are critical due to their impact on downstream capacity, and the investigation provided insight into where opportunities exist to extract more benefit. The findings of the geometallurgical analysis have been implemented on the concentrator, and improvements in the rejection of non-magnetic minerals have been seen.CITATION:Gerber, J, Stanton, C and Olwagen, D, 2015. Using geometallurgy during process optimisation activities at the Southern Middleback Ranges magnetite concentrator, in Proceedings Iron Ore 2015, pp 561–566 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By H S. Smit, P Lotz

Gold mining companies who are signatories of the International Cyanide Management Code (visit www.cyanidecode.org for further information) are required to measure WAD cyanide on-line and destroy WAD cyanide in excess of specified limits. Weak acid dissociable (WAD) cyanide refers to those cyanide species liberated at a moderate pH of 4.5 such as HCN(aq) and CN-, and the majority of Zn, Cd, Cu, Ni and Ag complexes with low dissociation constants. It is potentially toxic to humans and animals. Recognising and in response to the gold mining industryÆs need for an on-line WAD cyanide measurement device, Mintek recently developed the WAD Cynoprobe. The WAD cyanide analysis technique is based on the use of a ligand exchange reagent that liberates WAD cyanide from metal-cyano complexes. The ligand exchange reaction is represented by the following chemical equation: Metal(CN)X + yLigand <-> Metal(Ligand)y + xCN- The plant filtrate is treated with a ligand exchange reagent, to liberate WAD cyanide, before measuring the free cyanide concentration via amperometry. The instrument proved to be accurate and reliable in the laboratory as well as under industrial gold plant conditions during various trials. It has gained wide-spread commercial acceptance both locally and internationally. However, itÆs recent exposure to complex ore types have called for refinements to the analysis technique. It has been further developed to improve its precision and accuracy and to remove reagent and thiosulfate interferences. Its compatibility with the most commonly used destruction oxidants has also recently been investigated. The WAD Cynoprobe may be configured to measure both free and WAD cyanide concentration. Its fast analysis time, approximately 5 min, makes it suitable for use in the control and optimisation of the cyanide destruction and recovery process. Proper oxidant dosage control and monitoring of effluent concentration levels will ultimately result in less cyanide and post-destruction salts discharged into the environment.

Jan 1, 2008

Breakwater Resources Ltd is a Canadian base metals producer with Cu-Pb-Zn operations in Canada, Honduras, and Chile. Two of its operations contain economical gold levels which are recovered in both gravity and flotation concentrates. The gold payable terms in zinc concentrate are poor when compared to gold concentrates or copper concentrates and various flow sheets have been evaluated by Breakwater staff to maximise gold reporting in higher value products. The Myra Falls mine in British Columbia recovers coarse gold in the grinding circuit, part of which is upgraded and sold as a gravity-gold concentrate with the balance being directed to the copper concentrate. A sampling survey showed that there was potential gravity-recoverable gold in the copper regrind circuit. Installing a gravity concentrator in the copper regrind circuit increased the gold grade and recovery in the higher revenue copper concentrate and reduced the quantity reporting to the less well paid zinc concentrate. The El Toqui Mine in southern Chile has distinct high-and low-gold orebodies which are campaigned separately through the flotation plant. The high gold zone yields both a gravity concentrate and an unusual gold flotation concentrate. The gravity concentrate undergoes intensive cyanidation and electrowinning on-site to produce dore, while the fl otation concentrate is sold to gold producers. The zinc concentrate contains signifi cant gold values. The paper describes efforts over the past few years to improve gold returns at Breakwater's operations and highlights the different approaches dictated by the mineralogy of the gold occurrences at these two operations.

Aug 1, 2010

By Kentwell D. J, Cusak C. J, Harvey-Kelly F. E L, M D. Goodz

The Morning Star Gold Mine presents an example of a prolific operation with considerable historical records, mine workings, drill hole logs and countless plans from greater than 20 adjacent mines which have now been consolidated to form the current project. Implementation of 3D computer modelling in the planning stages has provided an additional tool to integrate and refine geological models as a guide to some exploration strategies. It has allowed for a re- interpretation of the host rock units, dimensional constraints, new exploration extensions and provisional resource modelling. The initial consideration of this project was to integrate 135 years of mining history into a single database. Each historic mining area had an unrelated mine grid, often established parallel to the long axis of their main stopes; some were based on magnetic or true north. Survey plans were in chain, imperial or metric units. Through the manipulation and rotation of old grids, previously unrelated mine workings began to form continuous mineralised zones, with unmined portions still remaining in between the existing development. Furthermore the current drillhole database of >433 holes showed numerous confirmatory intersections of new mineralisation. A series of tiered tables were created within a relational database to derive guidelines for assessing data to attribute a Mineral Prospectivity Value [MPV] based on key indicators of mineralisation. Indicator logging now forms the basis of geological descriptions.

Jan 1, 1997

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Mez W

the German ruining industry uses different residues for hackfilling and stowing. A hydraulic pipe conveying technology for these materials has shown advantages for the transportation into the mine. Pipeline conveying systems are able to bridge long distances, they save room within the underground workings and they save staff and costs. Absolutely necessary for successful use of the hydraulic conveying technology is the knowledge about the unusual non-Newtonian flow properties of solid/liquid mixtures like pastes and slurries. The flow resistance of these materials cannot be described easily by one viscosity. Owing to a yield point and a pseudo-plastic behaviour the viscosity changes with the shear rate and with the streaming velocity inside the pipe. Also these flow behaviours depend very sensitively on the liquid/solid-ratio, often so dramatically that gravimetric or volumetric dosing equipment is not in a position to control the production of backfill pastes. Quality changes of the solid raw materials (particle size distribution, density, mineralogical composition) lead to additional difficulties. The first experiences with hydraulic backfilling plants were troubled by plugged pipes. a bad backfill quality caused by unnecessarily high water content and high costs for chemical binders to solidify the backfill. The installation of viscosity controlled paste production leads to success with the hydraulic backfill technology. A development of the l)MT, a bypass pipe-viscometer, has been the key technology. The system is able to analyse on-line, difficult, sticky and abrasive substances and determine their non-Newtonian flow properties. Because the system measures real physical values it is in a position to pre-calculate process relevant parameters like the pressure drop of the backfilling paste in the conveying pipeline. Newer types of the viscometer system also measure the slurry density and calculate its composition. These systems have proven a success controlling backfill paste production plants. They offer it secure prevention of pipeline plugging and a production of high quality backfill pastes with a water content as low as possible.

Jan 1, 1998

By S Henderson

The Otago Goldfield has produced approximately 8 million ounces of alluvial gold and over 2.5 million ounces of hard rock gold and is currently home to New ZealandÆs largest producing gold mine. In the eyes of explorers this production history makes the goldfield a good place to explore.   Modern exploration in the Otago Goldfield commenced in the late 1970s with the exploration for tungsten. However, a rapid rise of the gold price in the early 1980s saw the focus shift to the exploration for gold which lead to the discovery of the Macraes Gold Project in 1984, which since it came into production in 1990 has been New ZealandÆs largest producing gold mine. With the exception of the Macraes Gold Project, exploration continued in the Otago Goldfield for a further 20 years without further success.   In 2006, Glass Earth (NZ) Limited (Glass Earth) reviewed all the exploration technologies applied to the Otago region and available geological data, including the 1996 OceanaGold Helicopter Electro-Magnetic (HEM) data, and concluded that combined magnetics and HEM were able to delineate the Hyde Macraes Shear Zone (HMSZ) which hosts the Macraes Gold Project. Unlike previous explorers who explored the Otago region in a piecemeal manner, Glass Earth opted to collect a new, region-wide dataset which could be integrated with all previous collected geological information to come up with new exploration concepts and targets. As part of this process, Glass Earth applied in mid 2006 for New ZealandÆs largest on-shore gold Prospecting Permit, PP39-322 which was subsequently granted in November 2006. In mid January 2007, Glass Earth commenced acquisition of approximately 50 000 line kilometres of HEM data, making the Otago regional aerial geophysical survey (survey) the largest aerial geophysical survey ever undertaken in New Zealand.   This paper will report on the progress of the Otago Regional aerial geophysical survey and outline some of the preliminary findings from what is still a work in progress.

Jan 1, 2007

By D J. A Van Zyl, J C. Cunning

Technological advances associated with the expanded application of paste technology in underground mine backfilling are now stimulating an interest in the disposal of process tailings as paste in the surface environment. Concurrent with the development of alternative surface tailings disposal practices is the requirement to fully understand the consolidation behaviour of tailings in paste form, and to relate this understanding to the significant body of data and operating experience from decades of study of the performance of hydraulically placed tailings. One effective method for demonstrating the benefits derived from handling and placement of tailings as paste is to review tailings slurry consolidation theory from the perspective of the changes which take place in the material as it makes its transition from a loose slurry to a dense, stable deposit resulting from managed thin-layer deposition. For a typical process tailings, an example is provided which illustrates the effect which mechanical dewatering has in accelerating the consolidation process and thereby providing a range of benefits from the perspective of surface disposal. Increased rates of filling (rise), expanded use of upstream embankment construction methods and elimination of impounded surface solutions are some quantifiable benefits which can be assembled on a site-specific basis to allow for valid comparisons with more traditional approaches to tailings disposal.

Jan 1, 1998

By J Benn, V Kuznetsov, G Timms, A Spain

Earthen covers are now widely used in the mining industry to control the generation rate and/or release rate of low quality drainage from piles of sulfidic minewastes. Covers are usually designed to reduce the water infiltration rate and in some cases may also reduce the oxygen flux to the underlying sulfides. Engineered covers have only been used since the 1980s, however, and there is very little field data on their performance in the longer term. This lack of information has implications for the degree of confidence that can be placed on the predictions of the environmental impacts of sulfidic minewastes, for the acceptance of close-out criteria by regulatory authorities and for the financial liability of the mining industry. Covers were placed on sulfidic waste rock dumps at the abandoned Rum Jungle uranium mine during 1984 - 1985. These covers were designed to reduce the water infiltration to less than five per cent of incident rainfall by both water shedding and storage-release mechanisms. Regular monitoring by the Australian Nuclear Science and Technology Organisation (ANSTO) demonstrated that the covers performed better than the design criterion for around ten years, but infiltration rates have subsequently increased. There is a 66 per cent probability that the infiltration rate now exceeds five per cent of incident rainfall. The cover on the largest pile, WhiteÆs heap, was sampled in pits dug at eight locations. Sampling was carried out at the end of the monsoonal wet season and again at the end of the ædryÆ season. This, together with laboratory testing, enabled cover performance to be assessed against five criteria: design, construction, cover material characteristics, physico-chemical characteristics and biological characteristics. We are of the opinion that the design of the cover was suitable to achieve the objectives of stability, water shedding, storage-release, and provision of a substrate for vegetation growth. Over most of the surface of the heap, the construction of the covers, drains and erosion prevention structures was in accordance with design specifications. However, several small and localised bare patches on the upper surface of WhiteÆs heap coincide with a reduced cover thickness, which is likely to have been due to poor construction in those patches. The construction of covers on minewastes is dependent on an adequate source of material meeting design specifications. From our limited examination, it appears that there was shortage of material for each of the three zones û a lower impervious clay layer, the moisture storage-release layer and the upper erosion-resistant layer for vegetative growth. An indication of this was that the upper layers in some areas were observed to be thinner than specified. We are of the opinion that this shortage of suitable material has been responsible for some of the changes observed ten years after emplacement. Physical and geotechnical testing indicated that the cover materials no longer meet the original specifications. In particular, the permeability at the 8 locations was found to be greater than specified, by up to several orders of magnitude. The higher permeability may explain the higher observed rainfall infiltration and moisture content of the waste rock. This increased permeability appears to be due to a combination of biological and physical processes û galleries formed by termites and ants and an extensive system of shrinkage/desiccation cracks formed by the development of a polygonal blocky structure involving the entire lower clay layer. The desiccation cracks may fill with coarser illuviated materials and form a conduit through which roots access the underlying waste rock. Measurements were made of oxygen flux into the heap as cover layers were excavated in the pits. They indicated that the full cover currently reduces the oxygen flux to 20 - 23 per cent of that into bare waste and that this reduction seems to be proportional to the cover thickness. It was also found that the oxygen flux into the cover is about four times higher at the end of the dry season than at the end of the wet season and that the difference is due primarily to the difference in moisture content of the cover. Recommendations are made for the design and construction of covers.

Jan 1, 2003

By M Haest

This study demonstrates the application of HyLogging™ technologies for mineralogical characterisation of different iron ore types throughout the Hamersley Province (Western Australia), including a channel iron deposit (Murchison Metals Ltd) and bedded iron deposits in the Brockman and Marra Mamba Iron Formations (BHP Billiton Ltd).Drill core from these deposits was analysed using CSIRO’s hyperspectral drill core logging systems (HyLogging systems), which are commercially available at the AMDEL and AMMTEC laboratories in Perth (Western Australia), through a leasing agreement. These HyLogging systems provide high resolution photographs at 0.1 mm pixel resolution as well as visible and infrared spectroscopic refl ectance data at 1 cm spatial resolution. The minerals identified include haematite, goethite and its subtypes (ie vitreous and ochreous goethite), AlOH-clays (kaolinite, Al-smectite and white mica), carbonates, gibbsite, chlorite, amphibole and hydrated silica as well as water content. The abundance and composition of these minerals was established from the spectral data and was validated against XRF analyses.The full potential of HyLogging systems in the iron ore industry is only starting to be unveiled, but some major benefits have already been demonstrated:• HyLogging systems can delineate different ore zones by mapping the vitreous and ochreous goethites. This has a potentially large impact in mine planning and operations, as hard, vitreous goethite and soft, powdery, ochreous goethite have different processing characteristics that can affect plant throughput if not carefully managed.• HyLogging mineralogy can also be used to support stratigraphic interpretations of the host, for example in subdividing the Dales Gorge 1 - 4 submembers of the Brockman Iron Formation.• HyLogging can have a potentially signifi cant impact on waste rock characterisation, as many of the waste materials can be identifi ed and quantifi ed with hyperspectral data (eg clay-type,• hydration state).• HyLogging can provide accurate three-dimensional (3D) mineralogy to iron ore companies that will empower them to improve future exploration and resource planning.• Application of high resolution photography to further improve ore deposit domaining is also to be considered.

Jul 11, 2011

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By C Claassen, R Balusu

Computational fluid dynamics (CFD) models have been developed based upon field data collected from a longwall mine in New South Wales, Australia to study the behaviour of goaf gas flow in both active and sealed goaf areas. A base CFD model was built to represent the goaf situations when the active longwall retreats near the finish-off line. Results from the base model were calibrated and compared against field goaf gas monitoring data. The base model was then used to carry out parametric studies to investigate a number of operational scenarios and their impact on goaf gas behaviour. CFD modelling results indicate that the overall goaf gas flow pattern changes as the operating longwall retreats towards finish-off line. In all cases, oxygen penetration into the active goaf remains high, reaching 15 per cent or higher, even at some 800 m behind the longwall face.The modelling results also indicated that it would be difficult for early detection of an active goaf heating (on the maingate side) based upon CO readings in the return airflow, as the main stream of the gaseous product will be flowing into the sealed deep goafs in adjacent longwall (LW) panels. Monitoring points (such as tube bundles and bag sampling points) should be selected at deep seated seals along the active goaf so that abnormal CO or C2H6 readings can be picked up for early detection and location of potential heating spots; goaf inertisation can be better achieved by injecting inert gas such as nitrogen at deeper points (>200 m) behind the operating longwall; the injection of in-seam drainage methane into the goaf areas will only have a limited impact on goaf inertisation as much of the injected methane will migrate towards deep and higher parts of the goaf due to its buoyancy effect.

Sep 26, 2011

By G Marling, A Calderon, J Harris, P Kirsch, M Shi, D Sprott, A Kirsch

Large-scale infrastructure construction needs to comprehensively manage risks that can impact the health and well-being of many people, from workers (temporary, contracted or full time), to families and surrounding communities. This paper starts with an analysis of incidents (injury, fatality, other damage) in tunnel construction between 2000 and 2014 and assesses the distribution of these events by continent, year, and severity of outcomes. These incidents are then analysed and mapped to a framework of hazards derived from RISKGATE (2014). A comparative register of current tunnel construction risk management guidance is derived from current Australian codes of practice and this register is also mapped to the RISKGATE framework of hazards to identify where coal industry knowledge may offer utility to the tunnelling industry.An initiative of the Australian Coal Association Research Program (ACARP), RISKGATE is an interactive online risk management system developed to assist the mining industry in implementing continual improvement in the management of major unwanted events. To date, a comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, outbursts, coal bumps and bursts, human/machine interface, manual tasks, slips/trips/falls, inrush and occupational hygiene. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.This paper proposes and outlines how knowledge within the RISKGATE platform could be applied to managing the significant health and safety risks associated with tunnelling. The authors suggest that to varying degrees the knowledge already captured in RISKGATE is likely to be transferable to tunnelling construction operations. Please note that this paper focuses on tunnel construction and does not address risk management of tunnels in operation (eg road transportation or utility networks).CITATION:Kirsch, P, Kirsch, A, Calderon, A, Marling, G, Harris, J, Shi, M and Sprott, D, 2014. Management of health and safety in tunnelling – application of Australian coal mining knowledge, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 563–572 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S J. Schafrik, C Keles, C Schlosser, E S. Gilliland, A K. Louk, N S. Ripepi, S Keim, J Amante, E Diminick

Three legacy coalbed methane production wells have been converted to injection wells for a one-year carbon dioxide (CO2) injection test to evaluate the potential for CO2 storage in the coal reservoir and the potential for enhanced gas production at offset wells. The injection reservoir is composed of 15–20 individual coal seams with an average thickness of 30 cm (1.0 ft), spanning a depth range of approximately 240 (800 ft) to 670 m (2200 ft).The monitoring program for this test includes gas and water sampling of the three injection wells, three dedicated monitoring wells and approximately 20 offset production wells. Key technologies used for monitoring the study area include time-lapse GPS and interferometric synthetic aperture radar (InSAR) acquisitions for surface deformation measurement, a 28-station buried passive microseismic monitoring array, real-time downhole pressure and temperature sensing and perfluorocarbon tracer fluids, which will be injected with the CO2 stream. The schedule for the monitoring program includes pre- (baseline), during- and post-injection data collection. This schedule will allow data to be analysed for time-lapse changes and trends, which are important for understanding the migration of gas and fluid phases in the reservoir – including CO2, methane, other hydrocarbons and water – and for observing the changing distributions of reservoir pressures and stresses.The results of the monitoring efforts for this study have implications for monitoring mining operations. The combined use of GPS and InSAR geospatial data to evaluate elevation changes across and beyond the study area may prove to be an accurate option for measuring surface deformation, including mining-induced subsidence, in unstable terrain. Long-term microseismic monitoring using high-sensitivity instruments has several applications in mining operations, including rock stability monitoring, production monitoring and miner location detection during emergencies. Tracer studies and short-term microseismic monitoring used to assess methane extraction can also be used to develop and optimise degasification systems for underground coalmines.CITATION:Gilliland, E S, Ripepi, N S, Schafrik, S J, Schlosser, C, Amante, J, Louk, A K, Diminick, E, Keim, S, Keles, C and Karmis, M, 2015. Monitoring design and data management for a multiwell CO2 storage/enhanced coalbed methane test in a stacked coal reservoir, Buchanan County, Virginia, USA, in Proceedings Third International Future Mining Conference, pp 47–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By N Madani, S Abulkhair, N Morales

Conventional geostatistical algorithms cannot reproduce bivariate complexities such as inequality constraint, nonlinearity and heteroscedasticity. Poor reproduction of these features may decrease the accuracy and reliability of mine planning results. For example, it is not unusual to have an inequality constraint between primary and disturbing elements in a metalliferous deposit. Implementation of traditional methodologies for such complex data sets can lead to the incorrect reproduction of a bivariate relationship, which will affect the validity of NPV results. In this paper, an iron data set containing iron and silica grades with an inequality constraint between variables is introduced as a case study. This study proposes an algorithm based on a hierarchical sequential Gaussian cosimulation integrated with inverse transform sampling. The proposed methodology considers the linear inequation between two variables in the hierarchical cosimulation process to reproduce an inequality constraint. As a comparison, conventional sequential Gaussian cosimulation is also applied to the same data set to demonstrate the difference in bivariate relationships from both models. Unlike the proposed algorithm, the conventional cosimulation cannot reproduce an inequality constraint and slightly overestimates silica grades. The modelled realisations are then used to assess the uncertainty of a plan and generate a stochastic strategy that adapts the destination of the blocks depending on the scenario. Two-stage stochastic long-term production scheduling takes extraction decisions using average information (ie e-type model) and ore/waste destinations based on geostatistical realisations. As a result, the proposed strategy is closer to the upper bound, highest possible NPV for each realisation, than to the lower bound, deterministic strategy that does not manage the risk of sending extracted material to wrong destinations. Furthermore, Comparing production schedules resulting from proposed and conventional geostatistical methodologies shows the importance of inequality constraint reproduction and more accurate long-term mine planning.

Nov 8, 2021

By Chappell B

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to he placed in a tailings darn. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electro- osmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By P Craig, A Crosky, P C. Hagan, E Elias, B Hebblewhite, S Saydam, D Vandermaat

"Premature failure of rock bolts has been recorded at twelve underground coalmines over the past 15 years in Australia. Over the last four years, UNSW Australia has been conducting an Australian Research Council (ARC) and Industry funded linkage research project into premature failure of rock bolts. The extent of the problem was investigated by underground surveys of mines with known prematurely failed bolts using visual mapping, non-destructive load and ultrasound testing. A major component of this project was to define the environmental factors responsible for corrosion of rock bolts. The environment to which a rock bolt is exposed will include groundwater chemistry, the mineralogy of the strata, atmosphere within the drill hole and even microbial activity. This paper focuses on the groundwater survey and analysis findings to date along with in-hole bolt corrosion coupons installed into field sites. Corrosivity classification systems exist for general corrosion but do not apply to the rock bolt stress corrosion cracking (SCC) problem found in Australian underground coal. The method of in situ investigations is leading towards the building of a corrosivity classification model to assist mines in prediction of premature rock bolt failure. An ‘in-hole bolt corrosion coupon’ development by the project may have multiple benefits of: helping quantify any corrosivity classification system providing an in situ ground support corrosion monitoring tool for testing possible corrosion protection solutions.CITATION:Craig, P, Saydam, S, Hagan, P C, Hebblewhite, B, Vandermaat, D, Crosky, A and Elias, E, 2014. An investigation of the corrosive impact of groundwater on rock bolts in underground coalmines, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 277–286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By J M. Nel

Richards Bay Minerals (RBM) has recently undertaken an exercise to improve orebody basal definition. Older mineralisation bases (pre-2005) were highly erratic using old protocol reverse circulation (RC) (also known as Air Core) drilling and interpretation. The erratic nature of this estimation tool, resulted in impractical modelling towards the end of mineralisation (EOM), difficult mine design and unrealistic reconciliation. New protocol drilling, which includes high definition SONIC drilling data, has provided more data to be available for more accurate interpretation. Recent advances in drilling methodology has allowed for better penetration depths for SONIC drilling, which was previously restricted to approximately 80 m (pre-2005). This improved data set allows more emphasis on geological interpretation with factors such as lithology, slime content, and mineral species distribution. These factors when in unique combination enable more accurate and realistic EOM data points. These points are modelled into surfaces using conditional simulation techniques and result in a vastly smoother surface and consequently, a more representative resource.

Oct 5, 2011

Mine site rehabilitation is the repair of the disturbance caused by mining on the immediate mining area and also on the surrounding environment. The long-term objectives of rehabilitation can vary from simply returning an area to a safe and stable condition, to restoring the mined land to a state as close as possible to its pre-mining condition, capable of being self-supporting and having a beneficial final land use. This paper investigates the importance and benefits of environmental planning, in particular for rehabilitation, and how input into daily operations can allow mining to progress with limited impact on the surrounding environment. It will also identify some of the key mistakes currently made during mining which could be averted by implementing prior planning and incorporating environmental consideration into daily operations. A number of rehabilitation opportunities will also be detailed for the different stages of the life cycle of a coal mine.

Jan 1, 2007