Search Documents

By K Lee, L Mann, J Bygrave, G Sheldon

Ausmelt is supplying commercial quantities of an alkyl hydroxamate flotation collector AM28 for flotation of oxide and supergene base metal ores and tailings. AM28 is a non-hazardous product used as a ten per cent to 50 per cent solution in dilute potassium hydroxide. It is a selective flotation collector for oxide or oxidised base metal minerals and replaces conventional sulfidisation for oxide mineral flotation. At Radio Hill, the AM28 is used in conjunction with traditional sulfide collectors, which allows simultaneous flotation of oxide and sulfide copper minerals. The Fox Resources Radio Hill copper concentrator near Karratha, Western Australia, is currently configured to treat supergene copper ore sourced from the West Whundo open pit. This Archean VMS type copper deposit has been deformed and remobilised with uplift, erosion and weathering to form a significant supergene zone. The sulfide copper minerals present in the upper zone are digenite and chalcocite with lesser chalcopyrite and covellite. Oxide copper minerals present include cuprite, with lesser malachite and azurite. Gangue minerals include quartz, talc and chlorite. Plant trials at Radio Hill are reported for supergene West Whundo ore, where the AM28 was stage added into the circuit at nominally 80 g/t. Plant data over three months shows the copper recovery increased consistently from around 50 - 60 per cent to above 70 per cent when AM28 was added. This has been proven statistically. The grade of the concentrate was consistent with and without AM28, at nominally 22 - 24 per cent copper.

Jan 1, 2007

By D Kent, R Paine

"Automated mining systems are increasingly being seen as a key requirement for a productive mining operation in the future. The importance of an integrated communication network infrastructure to support such systems is growing.This paper outlines the introduction of automated mining systems in large conventional mines as well as their growing role in block cave mines currently operating or being developed. The paper will then focus on a case study of how the communication infrastructure is fundamental to the operation of such systems and explain why the resultant communication networks require much more than just increased bandwidth (data capacity) to properly support the automation system within the overall mine operation.Mining operations already embarking down this road are discovering that the required network must be based on a true enterprise level architecture to not only enable the mine’s current plans for remote and automated mining, but also provide a scalable and integrated platform for future developments and requirements. The emerging issues for the communication network to truly support automation systems include: increased complexities of operating and maintaining multiple networks integration issues with disparate systems problems with reporting particularly as demands for corporate reporting and compatibility with enterprise systems become the norm ongoing management challenges, which will only increase with the proliferation of new technologies.The paper will explore how certain mining operations are addressing this by adopting a long-term strategy for automation deployment, which includes laying the necessary foundation architecture to meet their current requirements, while supporting their future visions for the fully automated mine.CITATION:Paine, R and Kent, D, 2014. Developing the foundation communication infrastructure to support remote and automated mining initiatives in underground mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 151–158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By P J. Vardon, L A. van Paassen, Y Yao, A F. van Tol

Thin-lift atmospheric fine drying (AFD) is a technique used to dewater mine and oil sand tailings, which utilises both self-weight consolidation and atmospheric evaporation. The disposed layers undergo a cyclic drying and rewetting process due to precipitation and deposition of additional lifts on top of the dried layer. The current research aims to optimise the deposition process via use of a numerical model and realistic atmospheric conditions, including both periods of drying and wetting. The model is based upon water balance and includes large strain considerations. A number of material behaviours are characterised using empirical fitting curves based upon laboratory measurement of material characteristics, including both the shrinkage and water retention curves for drying and rewetting. The model is able to model multiple lifts, simulating field scale and realistic climatic conditions within timescales suitable for engineering practice (eg seconds or minutes). The model has been previously validated against controlled laboratory experiments and utilised to simulate field tests. A series of simulations are presented to illustrate the ability of the model to be used as a practical tool for the optimisation of a tailings deposition strategy.CITATION:Vardon, P J, Yao, Y, van Paassen, L A and van Tol, A F, 2015. The use of a large-strain drying and consolidation model to optimise multilift tailing deposits, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By B Rouvray, R Bertuzzi

The development of a design-and-construct tunnelling project in Australia from its concept to its construction requires designs to be prepared and reviewed at several distinct stages prior to documenting ‘for construction’. On recent projects the post-tender stages have been variously called 30 per cent—70 per cent—100 per cent; or concept–substantial–final; or system definition–preliminary–critical. The design is reviewed at each stage by the designer’s internal reviewer, the contractor and its independent advisor(s), the owner and its independent advisor(s), the project’s independent certifier, proof engineers and often third-party stakeholders and their advisors. Documentation for each stage often dominates the design effort, at times distracting from design. This paper presents the authors’ experience of this design-and-review process. Comparisons of design budget and actual design spend and design program implications are presented. It is postulated that a subtle change has occurred in our industry that has diminished the value of the design dollar. Is there a better process? An alternative is suggested.CITATION:Bertuzzi, R and Rouvray, B, 2014. Reducing the cost of tunnel design in Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 501–506 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By P Christen, D R. Ashley, G R. Power

The Ernest Henry Mine is currently a copper-gold open pit operation situated in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current throughput of 11 million tonnes per annum; however, open pit operations are scheduled to cease in late 2011. The deposit dips at approximately 45¦ and extends for at least another 400 vertical metres below the final 530 m deep pit design. Resource drilling from 2002 until mid 2008 has enabled an Indicated Mineral Resource to be established to 1000 m below surface. Scoping and prefeasibility studies (PFS) have been completed toward determining if this resource is suitable for underground mining and a feasibility study is currently progressing with a sublevel caving (SLC) concept. This paper briefly describes the process by which the SLC method was selected, conclusions regarding the non-selected methods, and then discusses the optimisation process used to derive the mining plan. The key optimisation parameters include the production drive spacing, level spacing, draw strategy, cut-off grade and production rate. Key risks will then be assessed and economic sensitivities studied. Final sensitivities will use Monte Carlo simulations to improve the transparency of the projectÆs risk profile. The feasibility study (FS) began in March 2008 and this paper describes the main optimisation steps at the time of writing and outlines the plan for study completion through to March 2009.

Jan 1, 2009

By P Oikkonen

Sprayed concrete has played an integral role in underground rock support for nearly a century. However, concrete is also considered to be one of the biggest environmental problems in construction and mining, largely because of the high carbon footprint of cement and aggregates production. This is driving the industry to find ways to cut concrete usage where possible. Improving sustainability by cutting concrete material consumption also reduces application time and costs. Improving concrete properties can make it possible to design thinner linings, but as awareness of safety and longer design lifetimes are driving developments in the opposite direction, it is not realistic to see this as a major factor in cutting concrete consumption. More accessible solutions are focusing on layer thickness control and minimising rebound and wastage. Digital technology and innovation offer excellent tools for improving sustainability while optimising other aspects of the spraying process at the same time. A digital layer thickness control system gives near-real-time information to the sprayer operator with full coverage of the sprayed surface. This enables the operator to achieve consistent layer thickness on the first pass, in comparison to the traditional methods of overspraying with the aim of achieving sufficient layer thickness, probe drilling after the concrete has set, and respraying at a later stage if needed. Operator competence is the single biggest variable in a successful sprayed concrete process, affecting rebound and wastage levels. Unfortunately, the learning curve to become a master sprayer is quite steep and training on a real sprayer and real concrete requires a significant amount of time and money. Training in a virtual reality (VR) environment enables operator training to be carried out in a low-risk environment and provides a way of measuring performance and assessing and certifying the operators. After the VR training period, a novice nozzle operator has the basic understanding to start working on a real sprayer, and an experienced nozzle operator can benefit from the possibility of assessing their performance.

Mar 29, 2023

By M Gerards, M Steinberg, T Graham

The quality and quantity of Australia’s secondary deposits, which include tailings streams and tailings dams, are higher than most countries’ primary deposits. In addition, these secondary deposits have already been mined and processed, meaning that the recovery of high-grade product requires low capital and operating costs.The most widely used process for the recovery of these valuable fine and ultra-fine hematite iron particles is the wet high-intensity magnetic separation technique, originally developed by Dr Jones over 55 years ago. Many of the original machines are still working today.The aim of this paper is to demonstrate the capabilities in terms of grade and yield of using sophisticated magnetic separation modules. All results and figures are obtained from test work and design and engineering work with material from the Pilbara. In addition, consideration is given to dewatering of iron ore product and tailings.Two types of tailings have been identified for processing. Firstly, tailings that have already been deposited in a tailings storage facility, and secondly, live tailings streams from an existing wet iron ore beneficiation plant. In both cases, the technical and practical results are shown along with relevant flow sheets and plant layouts. Finally, this paper highlights the total predicted power and water consumption, capital requirements and projected operating expenses.The results show that the operating costs are significantly lower than the mining and processing operations that are required for an equivalent amount of iron ore. The recovery of iron depends on various factors but is within the 30–50 per cent range at an equivalent grade to the mainstream product. Another significant benefit is that the magnetic separation process is water positive, meaning that water is released rather than added in the process.The processing of the Pilbara’s secondary deposits will therefore result in an overall reduction in operating costs, an increase in product yield from a plant, extend the life-of-mine and offer environmental benefits by reducing the tailings footprint and water usage.The quality and quantity of Australia’s secondary iron ore deposits and tailings are such that many other countries would judge these as equivalent to primary deposits. Furthermore, these tailings are already mined, available and liberated to such an extent that the recovery of a valuable product is highly economical in terms of capital expenses and operating expenses.CITATION:Steinberg, M, Graham, T and Gerards, M, 2015. Recovery of iron ore fines and ultrafines from tailings by using wet high-intensity magnetic separation – JONES WHIMS, in Proceedings Iron Ore 2015, pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S J. Henderson

Pumped co-disposal of coal processing waste was promoted in the 1990-2000s as a low-cost highperformance alternative to tailings dams. In particular it would avoid high up-front capital for rejects trucks and dam embankments, and would produce a combined waste deposit with better geotechnical properties than either coarse rejects or tailings. Overall, the promise was not delivered; in particular, upon discharge the waste segregated by size, and operators responded by moving the coarser waste to contain the finer waste. In consequence, not only did design analysis lag behind construction, but some of the initial expectations persisted with the result that analyses did not fully represent what was occurring on the ground. After more than twenty years inspecting, designing and tending Co-Disposal Areas (CDAs), it is apparent that they are essentially upstream constructed tailings dams with some more favourable aspects but also a few unique quirks. Although waste management technology has moved on somewhat, the high cost of changing CHPP waste circuits means that most mines with pumped codisposal will continue to discharge mixed waste slurry into CDAs. It is therefore worthwhile to share some lessons in the hope of promoting sounder design, operation and rehabilitation. These include: • Discharged waste does not form a homogeneous wholly competent deposit but instead comprises materials ranging from sandy gravel to silty clay with the distribution determined by movement of the discharge and decant structures; • CDAs circulate and contain a lot of water; • As a result of the first two points, some areas of the CDA comprise saturated fine waste that is no different from tailings and, like tailings, often behaves in an undrained manner; • Seepage is inevitable and desirable because strength improves as water is removed. However, stability is strongly impacted by pore pressures and in design these need to be rationally rather than optimistically considered; • As CDAs are built to about 40m or higher, strength-deformation characteristics of the foundation become more important; • Even if geomechanically stable, CDAs will need covers to prevent salts and acids from reaching the surface; and • Erosional stability of the cover material(s) will probably dictate maximum slopes for rehabilitation.

Jul 1, 2021

By A Bennett, S Arndt

Minerals and Metals Group Pty Ltd (Golden Grove Mine) commissioned a comprehensive study of the life of mine using advanced 3D stress modelling. Essential input into the modelling was the proposed mining sequence, itself the culmination of years of planning and geotechnical experience gained in comparing actual performance to predictions. The modelling approach addressed the whole of mine at a scale of 5 km. There were however several magnitudes of scale to address, from the scale of laboratory testing (0.05 m), to drive size (5 m), extraction size (50 m) and stope size (500 m). Scaling was therefore an integral part of the procedure. The constitutive rock properties in terms of peak and post-peak behaviour varied with the scale. At the laboratory scale, the constitutive relationships for all the main rock units were determined in 3D as well as recovering the in situ stress using the rock memory technique, deformation rate analysis (DRA), whereas at the larger scale the properties were varied to match observations.The modelling, using non-linear analysis to account for rock mass yield and peak-residual strength, demonstrated that if the planned extraction sequence and stope geometry had been pursued there was a high probability of large volumes of excess shear stress being released. However, it was not possible to identify whether the excess shear stress (ESS) will release as one large event or many smaller events. The mining approach was to modify the extraction sequence/stope geometry to manage the hazard. This is where the economic advantage can be realised.Alternatively or in combination with further modelling, the volume identified with the predicted high ESS or energy release could be intensively explored for structures having adverse orientation to the stress change and with sufficient areal extent to release the ESS. The microseismic data can be interrogated for the likelihood of a large event to support the hypothesis of a singular release versus multiple releases of smaller events. If the initial planned extraction sequence had to proceed as designed, changes to dimensioned stopes would be recommended for risk mitigation. Mine planning could as an option, modify the sequence and the extraction could then be remodelled.CITATION:Bennett, A, Arndt, S and Dight, P M, 2014. The economic advantages of detailed geotechnical assessments for extraction sequencing, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 243–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Parrington PJ, Bailey A

Serious exploration for carbonate-hosted lead/zinc deposits in the Pillara district commenced in 1971 when Trend Exploration acquired exploration tenements covering stream sediment anomalies in the Limestone Billy Hills area. Shell Minerals managed the project from 1974 to 1976, and BHP Minerals Limited assumed management during 1976. Carbonate-hosted 'Mississippi-Valley- type' Pb-Zn deposits most commonly occur in Palaeozoic shallow marine carbonate complexes. At Pillara upper Devonian (Givetian/Frasnian) reef complexes are preserved on the flanks of Precambrian basement 'highs'. Within platform and atoll facies limestones sphalerite-galena- marcasite-calcite mineralisation occurs as disseminations, veins and breccia matrix, mostly associated with fractures and fault zones. Early exploration concentrated on detailed surface geochemistry and IP geophysical surveys, with geological mapping and shallow target percussion and diamond drilling. Results were discouraging and did not indicate potential for a shallow base metal resource. During 1976-77 BHP adopted a grid diamond drilling exploration technique and commenced testing an area of approximately 50 sq. km, initially using an 800 m square grid. In 1978 high grade mineralisation was intersected in an area subsequently named Blendevale. This was in the seventh diamond drill hole in the 800 m grid drilling programme, and to date more than 400 holes have been cored in the Pillara area. Detailed drilling at Blendevale has defined a number of mineralised breccia zones within an area of 2.4 km x 0.5 km, at depths of 100 m to 600 m below surface. The breccia bodies are associated with a series of north-south trending normal fault zones, forming a graben structure. The mineralisation occurs as breccia matrix surrounding unaltered limestone clasts, as veins filling steep fracture zones, and as

Jan 1, 1986

By S Hapugoda, J R. Manuel, M P. Ma, L Lu

Iron ore sinter quality depends heavily on the mineralogy, textures and physical structure of the sinter, which is formed upon solidification of the primary sinter melt. The interactions of the initial sinter melt with its surrounding materials will impact on the properties of the primary sinter melt and consequently the solidified structure of the sinter. By using a high-temperature visualisation system, in situ studies have been conducted on the effects of melt compositions (Al2O3, SiO2 and MgO) on the interfacial phenomena of the sinter melt on a natural iron ore substrate. It was found that the melt composition significantly influenced the wettability between the sinter melt and the iron ore substrate. The interactions between the sinter melt and the natural iron ore substrate were also examined. Such interactions can lead to further changes of sinter melt composition and hence the sinter melt properties that, in turn, further affect the wetting behaviour of the sinter melt.CITATION:Ma, M P, Lu, L, Hapugoda, S and Manuel, J R, 2013. Effects of melt composition on the interactions of sinter melt on a natural iron ore substrate, in Proceedings Iron Ore 2013 , pp 431-440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By B Stump

Reliable particle size analysis in minerals processing plants is a critical factor to the economic return of a plant. As recovery of valuable minerals is compromised for particles outside the optimal size range, effective and reliable particle size analysis is more crucial than ever, particularly in the current upswing of the global commodities market. Inefficient particle size analysis can lead to excessive over-grinding, thereby significantly increasing energy consumption and reagent costs, whilst negatively affecting process operation, thickening capacity, water recovery and tailings disposal.Australia’s first installation of a particle size analyser in Iron Ore has been monitored with great interest by the industry. Previously, manual size sampling at Rio Tinto’s Paraburdoo fines processing plant involved off-site sample analysis, with a turnaround measured in days. The Outotec PSI® 500 particle size indicator, commissioned in July 2009, takes approximately three minutes per line at site.The paper will include details on the following:• plant description,• sampling design,• PSI® 500 analyser functionality description, and• key learnings from site.

Jul 11, 2011

By A Huebner, A Noack

Companies all over the world are very sensitive concerning their IT and network security. In most network connected technical installations and machines however, network security is not taken into account to a significant extent: insecure protocols are run, unencrypted information is exchanged freely and even broadcasted wirelessly and networked machines are accessible via insecure file transfer protocol (FTP).What happens in case of malfunctions of such technical installations? Who is responsible? Who can be held liable in case of accidents? The first computer worm for automation systems (æSTUXNETÆ) (Symantec, 2010) was discovered during 2010.The paper is intended to create sensitivity among decision makers for potential security and resulting safety leaks and points out the current status quo in technical network security. It outlines best practices for secure networking and procedures for remote access and remote software updates on stationary equipment and mobile mining machinery. It describes how to ensure authentic and genuine configurations and software targets and how to ensure secure communication for autonomous and remote controlled equipment. For such equipment in particular, the following statement should apply: æThere is no safety without network securityÆ.

Sep 26, 2011

By J Jackson, E Sellers

Blasting related indices were developed to quantify variation in rock strength and structure for each stope, and for each lift of each stope, as part of a Mine to Mill study at an underground open stope mine. The indices were derived from combinations of data from underground diamond drilling because the simplifying assumptions contained in the block model prevented sufficient differentiation in rock mass characteristics to enable adjustments to the blast design.Application of combinations of blasting related indices enabled the identification of stopes with a high potential for inconsistent and oversize fragmentation, underbreak and overbreak. The indices also fragmentation outcomes to deliver increased material flow within stopes, better digability and predict indicative mill throughput. The stopes with issuesCalibration of the results enabled adjustments to the blast design based on the rock mass conditions and accordingly improved the blast outcomes. This enabled improved productivity by reducing underbreak and overbreak, having a more appropriate fragmentation, which reduces unplanned rock handling and improves bogging. The reduction in recovery drilling creates huge opportunities to improve output by reducing production delays and decreasing the overall cost per tonne. By understanding the explosive performance and blast energy distribution in relation to rock mass blastability poor, performing designs in blind upholes and convex stopes were identified.The conclusion of the work is that value improvement, regarding increased revenue and reduced costs, can be achieved across the whole underground Mine to Mill process chain by developing stope based indices from the existing geological information to correctly tailor the blast design to the rock within, and surrounding, the stope.CITATION:Jackson, J and Sellers, E, 2017. Blasting related indices as the key to underground blasting improvements in a challenging rock mass, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 23–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By C J. Carr

The Ernest Henry Mine (EHM) is owned and operated by Xstrata Copper and is located in North-West Queensland, Australia. The mine is currently undergoing a transition from an 11 Mtpa open pit mine to a large sublevel cave underground mine producing 6 Mtpa. Due to a number of factors, including geometry of the pit and crusher depth, the decision has been taken to develop a hoisting shaft rather than inclined conveyors.During the feasibility study the strip and line shaft sinking methodology was preferred over blind sinking due to scheduling opportunities and interactions with level development. Other methods of sinking considered included large-diameter raise boring, which was rejected due to concerns relating to centreline accuracy. The strip and line decision was reviewed during the tender process where better than anticipated blind sink advance rates and costs were presented. This in turn enabled the higher cost of the blind sinking method to be justified by a combination of reduced risks including schedule and ground water management. This paper discusses the pros and cons of both strip and line and blind sinking methodologies in the Ernest Henry context including sinking rates and total schedule impacts of the two methods, the key risks associated with each method, cost implications of blind sinking and safety implications of the work methods in general. The paper then concludes with the reasoning behind the decision to change to blind sinking for the EHM shaft.

Mar 21, 2011

By Szymanski J

Although efforts towards producing a `total quality rockfill product' have allowed cemented rockfill costs to be reduced considerably, there is still tremendous potential for further cost reductions. Cemented rockfill costs range from approximately $7 to $12 (US) per tonne of fill placed. Approximately 50 per cent of the rockfill costs are associated with cement costs. A large portion of the remaining 50 per cent is associated with labour and materials handling costs. Several Canadian underground mines utilise haulage trucks and/or conventional belt conveyors to distribute the rockfill. However, due to the restrictive nature of the underground environment, these current materials handling systems have limitations (ie spillage from trucks, dust from conveyors). The Sicon conveyor system (developed in Sweden) has considerable potential for replacing these current methods. The Sicon conveyor utilises a revolutionary approach - the conveyor belt is folded over upon itself (forming a tear drop shape) so that the transported material is completely encased within the belt. The Sicon conveyor's ability to negotiate very tight comers (without transfer points) makes the conveyor very appealing for underground mining applications. An analysis comparing the pros and cons associated with the Sicon conveyor system versus conventional materials handling systems will be presented in this paper.

Jan 1, 1995

By J Li, A McFarlane, J Yu, L L. Kuhar, R Meakin, N Chapman

"Column leach tests are used frequently to predict recoveries and reagent consumption for nickel laterite heap leaches. These column leaches often run for more than 100 days and therefore require long-term monitoring and data analysis to achieve the desired information. To minimise the cost and time required to obtain relevant information for nickel laterite heap leaching, we have developed a small-scale hydrogeometallurgical laboratory test to serve as a proxy to column, and by inference, heap leaching. In excess of 50 leach tests were conducted using four different small-scale proxy and column leach tests to compare predicted nickel recoveries, acid consumption and leach kinetics and to determine whether insight into potential scale-up effects can be obtained. The most promising proxy test was identified and we achieved a statistically significant recovery and acid consumption correlations between this test and the column leach tests. The accuracy of the small-scale tests was confirmed by column tests run on new laterite ores. This geometallurgical proxy could be of use for the population of block models and process selection during the mine planning phase or for optimisation and control during processing.CITATION:Li, J, Kuhar, L L, Meakin, R, Chapman, N, McFarlane, A and Yu, J, 2016. A Geometallurgical Proxy for Nickel Laterite Heap Leaching, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A Llewellyn, M Varvari

The ventilation circuit at the FrogÆs Leg Mine was originally designed to permit mining to progress down to 440 m below surface at a maximum production rate of 500 kt/a, as per the feasibility study. The FrogÆs Leg resource has now been defined down to 640 m below surface at a maximum production rate of 750 kt/a. In order to allow for this increase in production depth and tonnage, it was necessary to upgrade the ventilation circuit.This paper outlines the upgrades to the ventilation circuit that were undertaken and the underlying rationale behind them.CITATION:Llewellyn, A and Varvari, M, 2013. Ventilation upgrade at the FrogÆs Leg Mine - Case study, in Proceedings The Australian Mine Ventilation Conference , pp 95-102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By A Karrech, G M. Hassan, A Varghese, E Lessing, S Martins

Pumps play a critical role in mining operations, and their energy consumption and environmental impact are significant. This paper addresses the need for a holistic approach to sustainable pump deployment by expanding on previous work presented at IMPC Asia Pacific 2022 and World Mining Congress 2023. The research takes a significant step forward by outlining a structured approach to estimate and demonstrate sustainability tailored for operational slurry pumps. It details the calculation methodologies used to quantify the carbon dioxide emissions from electricity, wear materials and transport, as well as sealing water usage. To enhance practicality and usability, a simplified visual representation—called sustainability metrics—has been developed to monitor overall efficiency. The sustainability metrics consist of the availability, pump efficiency, and water utilisation efficiency. The proposed methodology is integrated with Pumps Condition Monitoring Service to maximise benefits. Three case studies, from iron ore, copper, and nickel operations globally, were employed to evaluate the proposed methodology. The findings demonstrate the critical role of sustainability calculations in understanding pumps operation. These calculations improve awareness of the pump’s role in the sustainability journey and enable effective monitoring. The studies highlight that continuous monitoring paired with effective prescriptive maintenance strategy can significantly reduce power and water consumption while maximising pump availability. The case studies also reveal significant shortcomings in current operational practices and non-optimal maintenance regimes, emphasising the need for practical recommendations to maximise savings and optimise pump performance. In the context of increasing climate change awareness and the imperative for global decarbonisation, this research highlights the necessity of critically assessing methods and operations to drive sustainability in the mining industry. By adopting a holistic approach to sustainable pump deployment, mining operations can effectively reduce their environmental impact while enhancing operational efficiency and economic viability. The proposed methodology and case studies provide valuable insights and practical recommendations for mining companies seeking to achieve sustainable practices and contribute to a decarbonised future.

Sep 1, 2024

Carbon sequestration in planted forests provides an immediately available, low cost option to address the greenhouse impacts of coal mining and coal utilisation in a carbon constrained world. In addition, planted forests also offer the opportunity to address other environmental issues, particularly salinity and loss of biodiversity. Given salinity is characteristically associated with agriculture in the 500 to 700 mm rainfall belt, then where such forests can also produce commercial timber products, they offer the additional opportunity to establish new, diversified rural employment in both timber growing and processing. In the majority of Australian catchments affected by salinity, where rainfall is generally less than the 700 mm limit to conventional forestry, and where groundwater reserves are often saline, the objective of achieving economically viable forestry production presents a significant challenge. In 1996, Saltgrow commenced a collaborative breeding program to combine the salt and stress tolerance of E camaldulensis, with the growth rate, stem form and wood properties of the commercial species, E grandis and E globules. This program aimed to produce trees with the potential for commercial rehabilitation of saline landscapes. Results covering a range of site conditions from SaltgrowÆs network of over 100 trials around Australia are presented. The opportunity for commercial plantations integrated with agriculture in low to medium rainfall areas to address salinity and sustainability will be discussed. In addition, the significant potential for partnerships between land-rich, cash-poor farmers, catchment management authorities seeking to invest in public good projects that enhance environmental sustainability, and major carbon producing industries with either mandated or voluntary requirements to curtail net emissions will also be discussed.

Jan 1, 2005