Search Documents

By K Ehrig, V Liebezeit, Y Li, B Pewkliang, M Smith, E Macmillan

Pre-concentration of low grade ores via the rejection of low/no value materials based on fragment size is the subject of many published papers and studies over the past decade. However, the possibility of upgrading should not limited to low grade ores given the high cost of capital, energy, water, reagents, and ultimately tailings storage across the mining industry. Mining and processing facilities at Olympic Dam consist of an: 1) underground mine where ore is extracted via sublevel open stoping and 2) integrated processing plant located on the surface which produces Cu-cathode, Au-Ag bullion and uranium oxide concentrate. Blasted ore is trucked/trained to underground crushers which produce an ore feed with a product size P80 = -145 mm. Crushed ore is then hoisted to the surface and delivered to the ROM pads via an overland conveyor. The typical copper grade of mill feed is approximately 2 wt%. A rapid assessment of the potential to upgrade Olympic Dam mill feed prior to the ROM pads via rejection of low value materials based on fragment size was completed using existing data. Three separate datasets were utilised to assess the deportment of Cu, U, Au across size ranges of 200 mm down to sub-8 m. Cumulative grade vs cumulative mass distribution graphs for each element were produced. This data clearly demonstrates that Cu, U, Au grades remain constant down to ~212 m, which happens to be the liberation size of the sulfides. Hence, no potential to upgrade the ore stream via rejection of +200 mm - to ~212 m sized materials prior to milling. Mineralisation within the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit (IOCG) occurs as disseminated sulfide grains within granite- to hematite-rich breccias. The typical sulfide grain size is sub-200 m that supports the outcomes of the grade deportment by fragment size study.

Nov 10, 2020

By A Galli

Traditionally pit optimisation and scheduling is carried out assuming that the resources, the commodity prices and production costs are all known. Once the pit contour and the mining schedule have been determined, geostatistical simulations can be used to assess the impact of the uncertainty in the resources on the pit design and the schedule, and likewise stochastic simulations can be used to test its robustness to fluctuations in costs and prices. But it would be more interesting to have a dynamic procedure for optimising the pit as the resources become better known and as economic factors such as commodity prices and costs evolve over time. This paper presents a novel approach for doing this. Rather than working with millions of small selective mining units, it was decided to work with large blocks, called macro-blocks. Mining sequences are defined as the quantities to be extracted from each macro-block in each time period. Feasible mining sequences are mining sequences that respect the accessibility constraints, and also the geometric constraints on the amounts that can be extracted from any one block over time, or from all the active blocks at a given time. Having defined feasible mining sequences, their mathematical properties were studied. It was found that natural breakpoints occur in the sequences when one set of blocks have been completely mined out, thereby opening up access to others. It was discovered that families of sequences exist, and that they are convex and closed under certain types of row permutation operations. Convexity is an advantage when optimising. The closure property opens up the possibility of mixing and matching subsequences of rows in the sequences. Another interesting property is that the sequences form branching families, rather like the binomial and trinomial trees used to model prices in finance and in real options.It is easy to generate large numbers of feasible mining sequences randomly. A two-step procedure is used to find the best one (or the best few) using three economic criteria: expected NPV,the probability of a negative NPV, and the percentage of years when the cash flow is negative. The procedure was tested on a synthetic gold mine based on the characteristics of the Essakane mine in Burkina Faso. The results were encouraging.

Sep 26, 2011

By M Rafty, A Markham, S Atkinson

Australia contains some of the most productive mining areas and is characterised by ancient landscapes and highly variable hydrology. Historical mining of iron ore, coal and other minerals has targeted ore deposits located above water tables, and elevated above creek lines where possible to reduce cost. The downturn in mining caused by falling ore prices over recent years has triggered a drive to reduce cost, maximise yield and delay capital expenditure associated with opening new mines. So as the ore deposits with more favorable mining conditions become depleted there is an increased focus on mining ore associated with valley floors and creek lines. This is demonstrated by a regional assessment of the extent of Channel Iron Deposits (CID) and Iron Ore (Fe) Mines and Deposits in the Pilbara Region of Western Australia (Figure 1). A large proportion of these mines are, or plan to, target high grade CID ore associated with existing creek systems. Figure 2 shows outcropping and inferred sub-cropping CID extents, which suggests there are vast quantities of CID ore deposits throughout the Pilbara Region, intersected by major creeks which could be mined at some point in the future using creek diversions (Atkinson et al., 2017). A similar picture could also be produced for coal mining in Queensland, particularly in areas such as the Bowen Basin.While creek diversions provide an opportunity to maximise the utilisation of these orebodies and extend the life of mine, creek diversions can involve substantial financial, social, environmental and regulatory risks that need to be carefully managed (Markham et al., 2017, Atkinson et al., 2017). This paper discusses the key issues and opportunities associated with diversion decision making. It highlights the importance of using a well-structured assessment methodology that allows key stakeholders to be part of the assessment process and is complementary to material presented in Atkinson et al., (2017). Design considerations for operational and closure designs are presented, as well as mine planning considerations, risks, cost saving opportunities and the benefits of an integrated approach to design. The role technology plays in diversion design and performance monitoring is discussed as are the potential opportunities for the future.CITATION:Atkinson, S, Markham, A and Rafty, M, 2018. Diversion decision making with an integrated approach to design for operations and mine closure, in Proceedings Life-of-Mine 2018, pp 74–79 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A A. Puhalovich

The placement of chemically reactive mine wastes in mined out pits (æpit backfillingÆ) is increasingly seen by industry as best practice to manage long-term environmental risks. This is primarily because leaving wastes at the surface, or allowing pit lakes to develop, can result in unacceptable environmental risks. The costs and practicality of mitigation options such as installation of covers and community expectations of landform re-construction to achieve a post-mining, beneficial land use are also important drivers for pit backfilling.Pit backfilling can significantly reduce the post-closure risks to receiving environments, by minimising seepage due to tailings, acid/solute generating waste rock and/or salts derived from mine water treatment. Environmental risks are often highest where wastes are located close to the ground surface, due to relatively high rates of groundwater movement in near-surface aquifers and/or failure of engineered structures due to rainfall/erosion processes. Placement of these wastes at significant depth in pits, subject to mine planning and environmental assessment, can address these risks by increasing the path length and resistance from contaminant source to receptor, thus enhancing encapsulation of the wastes.Pit backfilling can also be cost-effective for mining companies. This is because existing pits are developed on the basis of an economic return and thus provide an opportunity to store tailings in an existing æengineered structureÆ at little or no incremental cost when compared with building and operating a new tailings or waste rock storage facility, often encompassing complex cover/drainage management systems. Key issues for consideration are mine planning, the long-term geotechnical behaviour of the wastes (eg consolidation of tailings which leads to release of acid/solutes in tailings porewaters), seepage rates to downstream receptors/agreed end point criteria and potential resource sterilisation. Internationally, mine closure guidelines are also showing a greater recognition of pit backfilling in the context of allowing mining companies to meet agreed post-closure land use objectives.In summary, pit backfilling can enhance the encapsulation of chemically reactive mine wastes and environment protection, and with agreement on post-closure beneficial land use, can also help to deliver post-closure benefits to communities.CITATION:Puhalovich, A A, 2012. Pit backfilling - Managing chemically reactive mine wastes and achieving rehabilitation objectives, in Proceedings Life-of-Mine 2012 , pp 279-286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By R J. Butcher

Many deposits have been evaluated as potential block caves over the last 20 years due to the perceived benefit of low operating costs. However, block cave projects are typically capital intensive, with mass mining providing high throughput rates that required large investments in mining, processing and utilities infrastructure. While the key economic metrics in deciding to proceed with a caving project are typically net present value (NPV) or internal rate of return, these may not represent the best decision metrics for some companies. Where a caving project is competing for scarce capital amongst other projects in a company’s portfolio or where the caving project is the only project being evaluated by a company trying to raise capital, other metrics may be more appropriate. This paper explores the use of present value ratio and the minimising of maximum negative cash flow as suitable metrics in determining alternative strategies. Trade-offs between optimising for economic value and capital efficiency measures allow for decision-makers to evaluate potentially higher-risk, higher-capital and maximum NPV projects against lower-risk, lower-capital projects.CITATION:Stewart, C A and Butcher, R J, 2016. Block cave evaluation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 809–816 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J Yamatomi, Y Tamanishi, S Miwa

The four-dimensional (4D) network relaxation method, originally developed by Akaike in 1999, uses Lagrange relaxation and is known for its ability to include the price change and possible better outputs, but the computation time is huge. However, the continuous advancement in computer technologies allows the use of higher-speed computers with more memory capacity. Therefore, in this paper the authors have tried to implement the method with adjustments and improvements in its algorithm to suit the current computing system. As a result, the computation time has been drastically reduced and more constraints can be included, which makes the scheduling a more realistic one. The case study of an open pit gold mine with 129 500 blocks can be solved considering the capacity constraints in 71 seconds. In previous case studies, the mined ore had to be processed or disposed of immediately. Now, stockpiling can be included as another option. Since the details of the algorithm are still being improved, the computation time is a little longer than the previous cases without the stockpiling option. However, it is found that scheduling with the stockpiling option is possible in a reasonable time. In conclusion, the 4D network relaxation method has become more useful with advances in computer technologies and provides better results.

Sep 26, 2011

By J deVries, A Broodryk, P Kyselica, K McLean

Gwalia gold mine is located close to the town of Leonora in the Goldfields region of Western Australia, some 830 km from Perth. The mine is wholly owned by St Barbara Ltd, an Australian Securities Exchange listed gold producer and explorer. The Gwalia mine is a deep, all-trucking mine and is serviced by a 10 km long decline from surface. Mining is currently 1540 m below surface. Reserves extend to 1820 m below surface and are open at depth. The mine produces in excess of 200 koz of gold per annum.The Leonora area is hot and arid, with a mean annual rainfall of 230 mm and a 95 per cent mean daily maximum temperature of 20.3°C wet-bulb and 35.6°C dry-bulb.The primary ventilation system comprises a 490 kg/s surface exhaust fan, which draws air down a parallel intake system consisting of the decline, and a dedicated fresh-air intake system extending to the bottom of the production zone. Cooling is provided via a surface bulk air cooler serviced by an ammonia refrigeration plant that delivers 150 kg/s of chilled water to the bulk air cooler.The refrigeration plant and bulk air cooler were installed in 2008. The design allows cooling to be increased over time by installing an additional refrigeration plant in a lead lag configuration with the current refrigeration plant when required.Since 2008, expansion and increased depth reached a point where the underground heat load exceeded the installed capacity of the existing 4.0 megawatt rated (MWR) refrigeration plant. In order to maintain the mine design conditions underground, upgrading of the existing refrigeration system was required to bring the cooling capacity to 7.5 MWR.Two expansion options were considered: the addition of an ammonia vapour-compression refrigeration machine similar to the existing one or a lithium bromide absorption refrigeration system using waste heat from the site power station. The original design and layout of equipment on-site meant that either could be used, allowing an assessment of the merits of both when additional cooling was required.The decision was made to install a lithium bromide absorption system on the lead side of the existing ammonia refrigeration plant. This arrangement provides considerable economic benefits, including reductions in site-generated electrical power, generator fuel consumption and carbon dioxide emissions.This paper details the planning, design, installation and commissioning of the absorption chillers.CITATION:Broodryk, A, deVries, J, Kyselica, P and McLean, K, 2015. The design, installation and commissioning of an absorption refrigeration system at Gwalia gold mine in Western Australia, in Proceedings The Australian Mine Ventilation Conference, pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By T Muzondo, C Prins, D De Vaux, R Schouwstra

The Mogalakwena Platinum Mine in the northern limb of the Bushveld Complex is Anglo American PlatinumÆs only open cast operation exploiting the Platreef. The Platreef, which extends along the basal contact of the Bushveld Complex, is geologically and mineralogically a much more complex orebody than the Merensky and UG-2 reefs. Changes in the footwall and the genesis of the Platreef translate into a number of rock types being present. These rock types vary in hardness and recovery potential and present challenges to metallurgical staff trying to optimise the concentrator. A true understanding of the implications of treating these rock types is required if the maximum value from this orebody is to be obtained.In order to more accurately forecast production and incorporate ore variation in the mine plan and comminution and flotation circuits, a geometallurgical approach to managing the operation has been used and is being further developed.CITATION:Schouwstra, R, De Vaux, D, Muzondo, T and Prins, C, 2013. A geometallurgical approach at Anglo American PlatinumÆs Mogalakwena Operation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 85-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By M Bond, R R. Hargreaves, G W. Booth

There are numerous causes of speculative mineral resource and reserve inflation. Traditionally, these are linked to issues of data accuracy or misinterpretation, the use of overly optimistic estimation parameters or assumptions, an absence of independent expert verification, or the simple pressure to increase company value, covert or otherwise. Owing to its subjective nature, classification of resources and reserves remains an opaque process. Of necessity, Competent Persons rely on personal heuristic interpretations, ideally underpinned by appropriate estimation and classification experience across commodity and deposit types. Whereas independent verification of individual resource and reserve statements remains impractical, publicly available data can be interrogated for potential category inflation, particularly when viewed with exploration expenditure statistics included in annual company reports. Abrupt changes in category tonnages and market capitalisation without concomitant expenditure can aid in outlier detection. Consequently, a comparison of common exploration and resource reporting parameters offers a basis for risk assessing classification robustness, over time. In this introductory study, an analysis of globally listed companies was undertaken over a multi-year period, examining base and precious metal projects in both preproduction and operational asset classes. From these, a series of exploratory decision tree trigger points were generated against which target companies were anonymously identified and risk-ranked.

May 24, 2023

By T Trott, M Lewis, G Lumley

The analysis of equipment trends in The AusIMMÆs revision of Monograph 19 - Australasian Mining and Metallurgical Operating Practices (AMMOP) (in prep) in the paper by Graham Lumley raised some interesting, and in parts disturbing, trends in the Australian open cut mining industry. According to the Australian Bureau of Statistics (2011) the productivity of the whole mining industry is down by 34 per cent since 2001. In terms of open cut equipment, median output for draglines is down by 15 per cent since 2003, electric rope shovels are down by 41 per cent since 2003, hydraulic excavators are down by 39 per cent since 2008, front-end loaders are down by 39 per cent since 2007 and trucks are down by 41 per cent since 2006. Clearly e boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top ten per cent by annual output per unit of input) has declined, but not by as much as the median (eg shovels down by eight per cent, excavators down by 19 per cent and FELs down by five per cent). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins, pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one, will be crucial to reversing the decline in open cut equipment performance.CITATION:Lumley, G, Trott, T and Lewis, M, 2012. Reversing the trend in open pit mining equipment output, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 75-82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By G du Toit, P L. Gillot, M Swanepoel

Randgold Resources’ Loulo-Gounkoto Complex is one of the largest gold mining operations in Mali, West Africa. The mine, which is situated on the western border with Senegal, treats more than 4 Mt/a of ore through a conventional three-stage crushing and ball milling circuit followed by a carbon-in-leach plant. Ore supply is achieved by a combination of open pit and underground mining, with the majority of the ore supply sourced from the Gara and Yalea underground mines situated approximately 2 km and 6 km respectively from the gold plant.In 2011, Randgold Resources commissioned Golder Associates to perform an evaluation study for providing structural backfill to both the Gara and Yalea underground mines using the current gold plant tailings. The test work performed as part of the evaluation study concluded the need for a tailings cycloning and dewatering facility capable of producing slurry at a solids concentration of 65 per cent with a particle size distribution that had minimum 25 per cent passing 20 µm and less than 5 per cent of -5 µm material. Tailings desliming was required to ensure a consistent feed quality to the paste preparation plants and to ensure that the system would be capable of handling variation in the feed composition from the gold plant.WorleyParsons, previously TWP Projects, was contracted by Randgold Resources to complete the engineering design for the slurry preparation plant, whilst Golder Associates was retained to complete the engineering design of the two paste preparation plants.This paper discusses the test work, design considerations and engineering design of the slurry preparation plant, termed the ‘intermediate plant’, as well as all ancillary facilities required for the delivery of the deslimed slurry to the paste preparation plants located at the two underground mines.CITATION:Swanepoel, M, du Toit, G and Gillot, P L, 2014. Case study – engineering design for a slurry preparation plant for a paste application in West Africa, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 477–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D R. Anstey

The mining of magnetite iron ore in Western Australia will generate large volumes of waste rock and tailings over many decades. The need to dispose of these materials will result in massive waste landforms that will require significant planning and management. The formation of comparable man-made landforms is relatively common, as exemplified through past practice in gold and iron ore (haematite) mining. Unfortunately, the performance of these landforms, with respect to long-term stability (erosion resistance), the release of low pH seepage water and aesthetic impact, has commonly been disappointing and environmental legacies have been created as a result. Lessons that have been learnt from past, large mining operations indicate that there is a need to rethink the methods of waste disposal and landform development applied to magnetite mining. The environmental compliance criteria applied to magnetite mines for the storage of tailings and waste typically include minimising dust generation (particularly as the tailings and mine waste may contain asbestiform minerals), control of silt, minimising visual intrusion and management of potentially acid forming materials. In addition, the climate of Western Australia and the paucity of both surface and groundwater in the vicinity of the magnetite mines frequently necessitate water consumption to be minimised. This paper discusses the potential to co-mingle magnetite mining waste streams in a variety of ways to concomitantly satisfy the environmental compliance criteria and the operational requirements of the mine. These methods include co-mingling of coarse tailings and waste through dry-stacking, deposition of tailings as a paste, co-disposing of all wastes to form an integrated landform and the co-mingling of all waste streams to produce PasteRockTM (a blend of tailings paste and crushed waste rock). The paper demonstrates how these techniques can be applied to the magnetite mining industry to provide better outcomes than might be achieved using more conventional techniques, currently employed in large-scale mining operations.

Jan 1, 2009

By E Nunes, R Mendes, D Jacobson, G Cota, T Machado, E Santos, J Almeida, E Pereira9, B Raso

Grinding circuits are known to be the highest consumer of energy used in the ore comminution process, with high operational costs and sensitivity to ore conditions. The mining industry is being encouraged to look for more energy efficient processes while increasing the mass and metallurgical recovery; a specific example is projects with lower iron ore grades, which demands a higher level of liberation and resulting higher energy consumption. This has led to increased usage of high-pressure grinding roll (HPGR) technology as an alternative design within the comminution circuit. A growing use of the HRC™ HPGR technology has been used to generate concentrate through a more sustainable process. In the Brazilian state of Minas Gerais, the readaptation of iron ore beneficiation circuits has been initiated, replacing the traditional crushing-to-grinding flow sheet with circuits using crushing-to-HPGR flow sheets, with the main driver being reduced energy consumption. Utilising results from sampling campaigns and analysis of experimental data collected in an industrial plant, the work herein presents a case study from the JMN Mineração operating plant, where the HRC™ HPGR was used as an alternative to traditional grinding using horizontal mills. The results show that the HRC™ HPGR performance in this iron ore processing plant showed benefits in terms of reduced energy consumption as compared to the projected performance with a traditional grinding circuit.

Sep 18, 2023

By S Khosrowshahi, A Weeks, W J. Shaw

"To provide an indication of expected performance of the mine and mill, feasibility studies should include an assessment of the expected day-to-day variability in process plant feed. Attempts to do this based on conventional resource models will be flawed as such studies fail to consider and account for the in-built smoothing (averaging) of input data.This can lead to one of two situations: an expensive, over-engineered process plant that can cope with every possible situation, or operational strategies that fail to manage the natural variability within the orebody and the impact of day-to-day operational decision-making.In both cases the value of the project diminishes through excessive capital costs or reduced throughput or recovery during operations.Unlike conventional estimation techniques, the geostatistical method of conditional simulation can reproduce the inherent variability of the deposit. Once a valid model has been developed, it is possible to analyse the model using a transfer function that simulates the proposed mining processes and provides a representation of the likely variation of mill feed characteristics at any time scale.The case study demonstrates how the proposed mining strategy would result in mill feed being considerably more variable than expected, resulting in poor recovery, low throughput and potential breaches of environmental conditions. Mitigation measures included budgeting for additional mining equipment to enable greater flexibility during mining and revised stockpiling and crusher feed strategies.Awareness of the benefits of modelling the variability of geometallurgical parameters will increase the use of this approach in producing more realistic financial models of expected mine performance at the design stage.CITATION:Shaw, W J, Khosrowshahi, S and Weeks, A, 2013. Modelling geometallurgical variability - a case study in managing risk, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 247-252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By E Hawkins, S Sheldon

Block caving is becoming a more widely adopted mining method allowing for underground massive low grade orebodies to be extracted economically. Underbreak during cave propagation is difficult to predict in terms of recovery and is not well-researched due to the small number of caving operations. During mining of E26 Lift 2 (E26L2) block cave at CMOC Northparkes Mines, a wedge of high grade material failed to cave, even with the assistance of preconditioning and subsequent attempts to induce caving. The ultimate solution for recovery of the uncaved wedge was the establishment of the E26 sublevel cave (SLC), which commenced mining in 2015, with production following in 2016. The SLC provides approximately 1Mtpa to supplement the lowering grade of the current E48 block cave feed. Applying the sublevel caving methodology to recover block cave underbreak has proven challenging. The impact of the caving stresses and preconditioning of the wedge have caused production limitations requiring continual remediation throughout production of the E26 SLC. The dependence on remediation work created a roadblock to implementing precharging as the prevalence of brow loss raised concerns over the inability to hook up the charged ring. In 2018, a wireless initiation trial was completed in the E26 SLC over 24 rings. The trial showed that precharging was achievable in this environment and greatly improved the safety of charge up personnel.

Mar 15, 2021

By C A. Foss, D A. Clark, D Hillan

While magnetic surveys are the most common geophysical method used in mineral exploration, magnetics and geology remain to be fully integrated quantitatively in iron ore provinces. Although high-resolution aeromagnetic data has been collected over prospective areas of the Hamersley Province, much of the information in the data sets has hitherto not been fully exploited due to a lack of suitable interpretation methods. Recent advances in the processing and modelling of magnetics in highly magnetic terrains, constrained inversion and 3D visualisation and understanding the magnetic properties of banded iron formations and iron ores potentially create the capability to generate realistic 3D mapping of magnetite and hematite concentrations over large areas. Initial processing of conventional total magnetic intensity data produces true potential field maps that are unaffected by local perturbations of the regional geomagnetic field direction by intense local anomalies. The true potential field can be converted into vector and tensor components, each of which emphasises different structural features of the geology. Scalar quantities derived from these components simplify interpretation, using new methods, developed by CSIRO and elsewhere, that are less sensitive to magnetisation direction. Preliminary interpretations allow interpolation between mapped units and structures and evaluation of remanence and anisotropy effects. Accurate modelling requires rigourous treatment of self-demagnetisation and magnetic interaction effects. Semi-automated constrained inversion, combining magnetics with available geological information and other geophysical data, can be utilised to generate models of disposition of major magnetic units and the 3D magnetisation distribution within them. The final stage of interpretation is to exploit the understanding of magnetic properties (susceptibility, anisotropy and remanence) developed over many studies by CSIRO, the University of Western Australia and others to convert the interpreted magnetisation distributions into 3D maps of magnetite and hematite contents, which are the quantities of direct exploration interest.CITATION:Clark, D A, Foss, C A, Austin, J and Hillan, D, 2015. Three-dimensional mapping of magnetite and hematite concentrations from reprocessing of detailed aeromagnetic data, in Proceedings Iron Ore 2015, pp 229–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Mitra, D O’Dea, N Barrett, T Honeyands, P Zulli

The steel industry continues to explore and demonstrate technologies that decrease its greenhouse gas emissions, especially in blast furnace ironmaking where alternate operating conditions will be required. As the furnace has been optimised over many years, it is approaching the minimum fuel rate possible with coke and Pulverised Coal Injection (PCI). Alternative operating conditions are therefore required to further decrease greenhouse gas emissions. Because of this, hydrogen has been proposed as a reducing agent in the blast furnace. Injection of hydrogen through the tuyeres was assessed using a comprehensive 2D blast furnace global model. The model was calibrated to a blast furnace operating with PCI as a base case and various approaches to hydrogen injection assessed, with a particular focus on displacing PCI. The maximum hydrogen injection rate of 19.5 kg H2 per tonne of hot metal was predicted, limited by decreases in the raceway adiabatic flame temperature and top gas temperature. Internal blast furnace conditions, such as gas composition and reduction degree were also predicted. Holistic analysis was performed to estimate the effectiveness of hydrogen injection on reduction of greenhouse gas emissions. Based on these results, the changes in blast furnace operation and emissions under hydrogen injection are discussed.

Nov 8, 2021

By E C. Holloway

"The financial valuation of mining assets has a number of fundamental differences to the valuation of many other asset groupings. One such difference is that typically, the greater proportion of both the cost and revenue sides of the cash flow are inherently governed by systemic market forces.As a result, the range of outcomes for the valuation of each mining asset is more unpredictable, with higher levels of risk and uncertainty. In contrast, the management function of many other non-mining businesses or industry groups can control at least a portion of the cash flow by maintaining the margin or controlling the sales price. The management teams of mining businesses and operations typically have limited options, and are thus price-takers for both costs and revenues. As mining is an inherently cyclical industry, large, long-life operations can exist through several price cycles, making valuation both subjective and challenging.The outcomes of both static- and stochastic-based valuations, as well as the internal probabilities of the associated cash flow statements, are significantly impacted when the correlations between the appropriate parameters are quantified, modelled and incorporated into the valuation framework. The appropriate parameters for correlation modelling primarily include those that are governed by systemic market forces. Applying this process results in a different risk profile for the asset by allowing the risks resulting from systemic market movements to be more accurately quantified and then objectively minimised. This process also reduces the level of residual uncertainty in the valuation outcome.This paper presents a valuation methodology to pragmatically incorporate this level of valuation sophistication and statistically quantify the associated increase in the level of confidence of the valuation outcomes reported.CITATION:Holloway, E C, 2016. Correlated valuation methodology, in Proceedings Project Evaluation 2016, pp 181–200 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Y Li, Z Fu, D J. Williams, E Topal

Mine waste rock is unavoidable in the recovery of ore by open pit mining methods. Effective management of waste rock movement covers the removal and placement of the waste rock, generally in a surface dump in the most cost-effective way while satisfying the long-term environmental expectations. Since the 1960s, there has been significant research carried out into planning of ore movement from open pit mines such that the overall net present value (NPV) of the project can be maximised. Currently, several software packages are available to achieve this task as a common practice within the mining industry. However, planning of mine waste rock movement is still achieved manually, as the available software does not consider optimal waste rock movement and dump design. This paper describes a tool to optimise waste rock placement, which minimises the haulage cost while creating environmentally friendly waste rock dumps through selective placement and encapsulation of the reactive waste rock in the dump. The embedded methodology in this tool has been developed based on the mixed integer programming (MIP) modelling technique to optimise the waste rock movement. The methodology provides an easily-manipulated and fully-automatic tool for professionals to complete waste rock dump scheduling in four main steps: data input, model construction, model computation and solution retrieval. The application of the new tool into a real case project in this paper shows that it can determine economically and environmentally optimised waste rock dump schedules in an acceptable time frame.CITATION:Fu, Z, Li, Y, Topal, E and Williams, D J, 2015. A new tool for optimisation of mine waste management in potential acid forming conditions, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 333–342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R Williams, M Baxter, D Zink, R Cunningham

The purpose of this paper is to discuss the efficient operation of a tailings dewatering circuit comprising a thickener and filter press through proper control and automation. It is common to see thickeners and filter press circuits each with their own control systems. This can cause multiple issues when trying to increase efficiency and reliability of the tailings management process. By automating the thickener and filter press controls, you are eliminating any delays and inconsistencies caused by human error and process variations. When done properly the system can maintain a consistent product as the feed characteristics change. Previously, operators would have to monitor the process parameters and adjust the system accordingly. This can now be accomplished using state of the art process control equipment that continuously monitors and adjusts critical variables using Programmable Logic Controllers (PLC) and Proportional Integral Derivative (PID) loops. The paper will detail the control theory used to maintain these systems, highlight other benefits of having a fully integrated plant such as predictive maintenance and remote diagnostics as well as present examples of how these have been implemented in field examples.CITATION:Baxter, M, Cunningham, R, Williams, R and Zink, D, 2018. Tailings process optimisation through automation and controls integration, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 416–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018