Search Documents

By J J. Boshoff

This iron ore mine site, located in the Pilbara region of Western Australia, commenced operations in 1998, with ore derived by mining of open-cut pits in Channel Iron Deposits (CIDs). A portion of the ore extracted at the mine is processed at wet processing plants that produce both ore saleable product and waste fines (i.e. tailings) slurry. The waste fines produced at the wet plants are presently stored within Waste Fines Cells (WFCs).Waste fines cells A (WFCA) and B (WFCB) are located within an Autonomous Haul System (AHS) area and consist of embankments that span the width of the pit in east-west alignments. Technical studies and design analyses were carried out to support embankment raises and ongoing development of the WFCs. During operation and development of the WFCs, a multitude of simultaneous activities took place to the immediate north and south of WFCA respectively. These activities included the construction of the embankment raises using the AHS fleet, mining of the CID to not only mine the ore but to also create future deposition space for WFCB, blasting next to the WFC embankments as part of the mining activities, seepage collection and dewatering of the pit in the vicinity of the WFC.This paper discusses the material characteristics, design approach, construction staging and equipment requirements, blasting near embankments, water management, facility consequence category and closure concept.CITATION:Boshoff, J J, 2018. A waste fines cell with a multitude of concurrent activities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By N Clarke, A Barros

Preconcentration of run-of-mine subgrade and marginal ore by screening has the potential to substantially improve the economics of mining, particularly for large, low-grade orebodies, and to reduce environmental impacts. It has recently been the subject of a major research effort by a joint public-private research body, CRCORE. Yet despite this, there appears to have been only one fully commercial installation, at Bougainville Copper Limited in the late 1980s. Two reasons for the limited application are that not all ores have suitable properties and the economics of all pre-concentration processes on low-grade materials are highly sensitive to the precise balance of mass and value recovery and to the pre-concentration process cost, including materials handling. These factors make it imperative to have good test data on the process response of feedstock across the orebody. Collecting that data presents major challenges, which differ for green and brownfields operations. This paper first discusses the approach to preliminary evaluation developed by CRCORE, which relies on testing of coarse rejects or drill chips available from exploration drilling programs. This method is an efficient first step in evaluating an orebody which is deemed geologically to be potentially amenable to screen upgrading, but it does have limitations and must be followed by larger scale work. A suite of methods have been developed by the authors as a result of test work since the 1990s on several projects, supplemented by published data, which aim to provide statistically robust data at lower cost than large scale bulk sampling tests. For greenfields projects, the upgrade response measured on material crushed to -53 mm has been found to correlate closely with ROM ore, with no scale-up required for material with upgrade responses in the range of commercial interest. Large diameter whole drill core, such as PQ, is expected to be suitable for this method. As drilling such core is costly, the aim should be to establish relationships between upgrade performance and proxy measurements such as multi-element chemical or hyperspectral analyses. This approach was successful at the Gramalote gold project in Colombia. The method is not applicable for ores with thick vein material comparable with the crush size, but such material is not suitable for upgrading by screening and would be eliminated by the preliminary testing. For brownfields projects where blasted material can be sampled, the upgrade response can be accurately measured by sampling only the finer fraction of the ore, selecting a top size which represents 30–50 per cent or more of the ROM size distribution. This is likely to be between 50 and 100 mm. The much finer size compared with the full ROM ore greatly reduces the sample mass required to achieve a given intrinsic sampling error and enables sample preparation to be undertaken with large-scale laboratory equipment rather than mobile crushing plant. The accuracy of the method can be improved by measuring the approximate mass of oversize rejected during sampling. Some ores do show a systematic deviation from the assumed model fit which results in this method slightly underestimating the upgrade response, and it would therefore still be recommended to take one or two full bulk samples to confirm results before a final investment decision.

Aug 24, 2022

By M Orunesu Preiata

The Odysseus Project is part of the high-grade Cosmos Nickel Complex that lies 30 km north of Leinster. The Odysseus definitive feasibility study (DFS) was approved by the Western Areas’ board in October 2018. Early works commenced in January 2019 with rehabilitation of the existing underground infrastructure. In June 2022 Western Areas was acquired by IGO Ltd. The project is now well advanced to meet its target of first concentrate. The project included the construction of a haulage shaft. The design of the hoisting equipment and the shaft barrel evolved from the initial DFS design stage to the final execution, as the data were made available from the initial investigation to the data gathered during execution (although this did not change from its initial concept). The design philosophy for the haulage shaft incorporated, from the beginning a multidisciplinary approach with inputs from three main areas involved in such projects, namely excavation techniques, geotechnical assessments, and infrastructure construction. This interaction is a fundamental component for the success of such a critical project. In fact, each of these three areas influences each other in a cyclical manner, triggering a continuous review of the project inputs and outputs, while maintaining the original project goals: the design of an infrastructure able to deliver the desired throughput. The throughput dictates the infrastructure that needs to be built, which in turn controls the size of the shaft. The key assumption applied to this is that the rock mass can accommodate the excavation void, and the excavation technique with its tolerances and limits that ultimately need to be verified back with the initial assumptions used for the infrastructure design. The aim of the paper is to present a case study of the experience gained with the Odysseus hoisting shaft and to propose a possible logic path for similar projects elsewhere.

Mar 29, 2023

By A Horn

Mineral processing is characterised by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high-grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customer’s requirement for product purity and consistent quality increases.Over recent years beneficiation techniques for iron ore fines have become more important in order to achieve a maximised utilisation of ore resources and to produce competitive products according to international standards.Many high capacity iron ore beneficiation plants that target the production of fines focus on gravity separation processes using fluidised bed classifiers and spirals or wet high intensity magnetic separators as an alternative. This paper demonstrates the suitability of utilising the allflux® two-stage fluidised bed classifiers to treat iron ore particles up to 2 mm in size as well as showing how the high capacity gaustec® wet high intensity magnetic separation (WHIMS) technology offers several advantages compared to other WHIMS technology.The combination of the allflux® and gaustec® technologies offer the following benefits:The two-stage fluidised bed classification extracts a significant amount of concentrate from the feed. This in turn reduces the feed capacity required for the gaustec® WHIMS located downstream.The second classification stage produces a -0.5 + 0.1 mm product and a -0.1 mm product. The efficiency of the magnetic separation on these classifi ed products is high due to optimised settings for each size fraction.

Jul 11, 2011

Although the mining of metals was well established by the time of the Roman Empire mining skills did not really advance greatly for many centuries. Miners did not have the scientific knowledge to distinguish minerals, to process them, and to obtain the best recovery. Each mine essentially developed its own methods in isolation, most of them dangerous. However, with the beginning of the industrial revolution in the early 18th century there was a rapid increase in mining activity in Central and Western Europe and an accompanying need to educate professionals in the developing fields of science and technology. There was also a need for specialised schools (for example, Schools of Mines) to accomplish this since the universities of the time, formed as early as the first half of the 12th century, were cloistered institutions, focused on the study of classics, theology and law. The earliest attempts at organised technical education were made in 1702 with the establishment of a School of Mines in Frieberg, Germany (Table 1) to service rich copper mines, and in 1747 with the establishment of a School of Mines in Paris. By this time, the industrial revolution was well under way and other Schools rapidly followed, at Clausthal in the Ruhr region of Germany in 1775; in 1777 at Almanden to service the mercury mines of Spain (later transferred to Madrid); in 1780 at St Petersburg, Russia and at Falun, Sweden in 1819. The academic staff for these new institutions were often trained in the original School at Frieberg.

Jan 1, 2002

By K Evtiminova, G Jobson, M Nolte, S Meik

Chelopech Mining EAD (CMEAD) is a wholly owned subsidiary of Dundee Precious Metals Inc (DPM) and operates the Chelopech underground mine and processing facility located in Bulgaria. The final product sold is a flotation concentrate containing copper minerals with associated gold and silver. The increase in production from 0.6 to 1.0 Mt/a by 2009 occurred with the original (1975) secondary/tertiary crushing, and primary/secondary ball mill circuits. As part of the mine/mill upgrade project to 2.0 Mt/a, a new single stage semi-autogenous (SAG) mill and ancillary equipment was installed, replacing the original circuits, with commissioning occurring during the first half of 2011. Aspects of the design, commissioning and operation of the new comminution facility are the subjects of this paper.An extensive program of comminution characterisation test work was completed in 2004/2005, which indicated moderate hardness and competency characteristics. The characteristics were considered suitable for a range of comminution approaches which were assessed with respect to power requirements and capital and operating costs. Retention of the existing primary crushing facility, and installation of a new single stage SAG mill located within the existing mill building, was selected as the design for the expansion.An extended ramp-up schedule for the overall concentrator upgrade turned out to be necessary as the comminution and flotation circuits were completed prior to several downstream unit processes (concentrate filtration and tailings thickening), which were required to reach the design mill feed throughput rate on a sustainable basis. This resulted in the opportunity to gradually increase the SAG mill ball charge as necessary, to obtain the throughput corresponding to the various downstream processing constraints.A relatively fine cyclone overflow stream particle size distribution is a feature of the Chelopech comminution circuit that has not been fully overcome with increasing ball charge conditions. However, design throughput has been met even under the finer product size conditions and will be consistently achieved following the commissioning of two further process improvement projects scheduled for late 2012.CITATION:Jobson, G, Nolte, M, Evtiminova, K and Meik, S, 2012. The modernisation and upgrade of concentrator operations at the Chelopech Mine, Bulgaria - Design, installation and operation of the 250 tonnes per hour comminution circuit, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 325-332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

The subject of my paper is one which, I am certain, has exercised the mind of every man on whom depends the safe and economical conduct of mining operations; particularly in this district where the enormous size of the ore body has necessitated the mine workings assuming a scale that was hitherto unknown in the history of Australian mining. I, therefore, approach the subject with the feeling that I am displaying considerable t.emerity, knowing as I do that the subject has engaged the earnest attention and thought of everybody immediately concerned in the extraction of the ore of this district, and particularly of the Broken Hill lode.I think I shall not be contradicted in asserting that a very large proportion of eur accidents are distinctly traiceable to inexperience on the part of the miner, and records at the mines and verdicts of coroners' juries in many instances uphold this assertion by showing that the accident under notice was the direct result of lack of knowledge of the conditions of the work, or, at any rate, of an error of judgment hardly conceivable in the experienced miner. That this assertion is correct may also be proved by visiting any of the mines of the district.To the experienced eye it will be evident at once that a very large number are not in way skilful in the use of their tools and, therefore, lack the experience which of necessity must be coincident with the acquirement of skill. Now in making this' assertion, I do not intend to be too sweeping...

Jan 1, 1903

By Y G. Anoman

This paper discusses the operating model within Endeavour Mining Corporation regarding the options of owner mining against contract mining. It’s based on the concept of ‘are we carrying out the most efficient mining’ regarding cost and performance. This question can only be answered through an extensive contract mining tender process and conducting a comprehensive comparison to evaluate the transition viability. Karma mine, located in Burkina Faso, is the subject of this paper. The Tender model included sales of equipment, parts and tooling associated with the traditional Load and Haul Schedule of Rates (SOR). The methodology focused on the structure of the tender process, which consists in the development of a SOR based on haulage profiles and mining schedule. This is a new Endeavour framework that allowed the bidders to compete on an even level. This was performed using a systemic analysis which encompassed all the elements involved in a transition such as the Human Resources (HR), taxes and customs implications, directs and non-direct costs (Finance and interest on assets, depreciation, insurance), contractor risk profiling. It was assessed against the normalised internal pricing tender-based. This paper gives an insight into how a West African mining operation addressed the sensitivities of the HR functions against the commercial aspects. This was one of the most successful transitions in West Africa and was carried out during the COVID crisis. The outcome of this project has created value by detailing a lesson learned model for both commercial and HR aspects. This discusses the commercial comparisons along with the internal model with the underlying HR functions as a risk factor that could have jeopardised the continuation of the operation. This resulted in a smooth transition with the additional cash flow generated by the sale of the parts and equipment turned Karma into a viable operation.

Jun 22, 2022

For years traditional optical microscopic techniques have been used successfully to carry out mineralogical studies on processing products. Essential information could be obtained by supplementing microscopic data with X-ray powder diffraction data, chemical analyses, etc. However, most of the time the mineralogists working on plant related issues, would supply qualitative information to the metallurgists, due to quantification not being possible in the available time. Since the late-80s, the use of semi-automated to automated techniques for mineral quantification has impacted positively on the use of mineralogy for optimising processing plants. Rustenburg Platinum Mines (now Anglo Platinum) were the first mining company to purchase a Qem*Sem in 1987. With the success achieved in quantifying the minerals in the concentrator streams of the Rustenburg Platinum operations, a second instrument was purchased soon after. These instruments have proven invaluable tools in understanding the flotation behaviour of the sulfide and gangue minerals in the various reefs of the Bushveld. Restrictions in the resolution of these earlier instruments, as well as the time involved in searching for and correctly identifying the fine-grained platinum-group minerals (PGM), meant that these investigations focused on the deportment of the more abundant base metal sulfides, rather than on the actual PGM. The Mineral Liberation Analyser (MLA), which became available in the late 1990s, was well suited to detect and analyse minerals occurring in trace amounts such as the PGM. Anglo Platinum was the first mining company to purchase such an instrument and now has fourteen systems operating at the AR Crown Mines site. One of the applications of these systems involves the study of feeds, concentrates and tailings from the various concentrators on a monthly basis. These routine investigations provide information on a variety of mineralogical parameters, including liberation, association, and grain size. Results are used to emphasise areas for improvement, and specifically underline those areas where improvements will have the most impact on recovery. After new or different technologies have been implemented, mineralogical characterisation of the different process streams is an essential component in the assessment of the impact of these changes on flotation performance. In addition, the knowledge is databased for future reference to draw trends across the various concentrators around the Bushveld complex, and is also used for comparative studies when plants experience high losses to tailings. Due to the success of these investigations the question was posed whether it was possible to obtain data on a daily basis, as compositing samples could hide the impact of daily events. Although the instruments currently used are suitable for a research environment, these are not ideal for mine-site implementation. For that reason Anglo Platinum, together with FEI embarked on a development program to develop a system that can be implemented on-site to measure the important mineralogical characteristics on a daily basis. Important requirements for such a system include time-to-data, ease of use and regular quality control. Highlighting some results from concentrator studies, the presentation will review the progress on the development of automated mineralogical techniques for fast, automated mineral measurements. This is an abstract only. No full paper was prepared for this abstract.

Sep 13, 2010

By L Manca, P B. Hills, D Tyler, N Pollington

This paper describes a collaborative project undertaken by Newcrest Mining Limited (Newcrest) and pitt&sherry to identify, develop and then implement global best practices to manage the exposure to inrush (dry and mud) hazards in underground mining operations. An extensive literature review was undertaken to identify past experience globally and the current state of knowledge and practice in managing inrush hazard. A key requirement of the literature review was the development of a list of guiding questions which would form a framework for approaching operators to discuss the topic, capture recent learnings and understand current operating practices to allow the development of a best practice solution. An initial cohort of 14 mines across four continents chose to contribute and detailed interviews were carried out by the project team. The outcome from the literature review, interviews with participating mines and various internal discussions was a comprehensive summary document detailing Basic versus Best Practice management of the inrush hazard. This document is being used as a gap analysis tool by Newcrest to assess and guide the management of inrush hazard at their existing and future operations. The summary document has also been provided to the participating mines for their consideration. The project is iterative and will continue to evolve as new experiences, knowledge and practices come to light.

Mar 15, 2021

By C Dowding, C Aimone-Martin, P Abeel

This paper presents measurement and analysis of the dynamic response of a five-storey building to very high frequency excitation (>100 Hz) from blasting vibrations originating from a contiguous excavation of rock. Velocity response measurements in the rock and on the structure were employed to calculate the time-correlated dynamic displacement response of the building to blasting. Time-correlated structure response measurements are needed to advance the understanding of the response of urban structures to high-frequency excitation. Current regulations and understanding are based upon measurements of the response of one- to two-storey residential structures by 10 to 40 Hz excitation. The extension of these observations to taller structures when excited by high-frequency excitation needs to be investigated further.Measurements show that the amplification patterns at the ground level and top of the structure match or are lower than that observed by the US Bureau of Mines (Siskind et al, 1980) for the shorter residential structures. They decrease with increasing peak particle velocity. From the measurements, the global transverse shear strains found by differentiating ground floor and top displacements were calculated to be 12 µstrains. Time-correlated bottom and top of structure displacements show that building response may be more reflective of wave propagation up the structure than whole-structure inter-storey drift.In addition, a 3D model was used to compare computed displacements and strains to measured results. Modelled responses varied considerably, both in magnitude and location of the maximum strain. No conclusion can be made regarding the best 3D model to employ to simulate building response. More data such as motions measured at many points in the structure are needed. Maximum inter-storey transverse shear strains calculated with the model were found through the acceleration excitation and were less than 12 µstrains for 37 mm/s rock motion excitation. The inter-storey transverse shear strains calculated with rock displacement input were less than that found with the acceleration excitation.CITATION:Dowding, C, Aimone-Martin, C and Abeel, P, 2015. Measured and modelled response of a multistory, urban structure to high-frequency blasting excitation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 211–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

In the last 40 years, New Zealand has developed a number of liquid- dominated geothermal steam fields, for electricity generation and indus- trial process steam. New technologies were developed, and in this work, New Zealand led the world. The policy of full publication of the results, in a wide range of sciences, provided a reservoir of detailed data defin- ing the geology, size and shape, and the chemical and physical regime, of many geothermal fields and their constituent parts. The discovery of precious and base metal deposits /precipitates in geothermal drill cores and steamfield equipment, suggested a clear link- age with epithermal mineral fields in general, and with that of the Coromandel (Hauraki) Region in particular. Further work on geothermal/ epithermal relationships have implied that the techniques, developed to obtain an understanding of geothermal fields, could be applied also to epithermal mineral exploration. This work is developing fast, and is now proceeding in many coun- tries. Future work may show that the presumed relationship between geothermal and epithermal deposits may be applicable in the wider con- texts of all hydrothermal deposits, and possibly in many other minera- lised areas with volcanic "country rocks".

Jan 1, 1988

By T Trott, G Lumley

"The mining industry suffers from a shortage of professional and other workers. Research and analysis has demonstrated a close correlation between high performance in productivity, maintenance and safety. There is also a significant correlation between engagement and performance. It is the hypothesis of the authors that mines can use a strategy of establishing themselves as a high-performance mine to attract and retain high caliber professional people: step 1 is to become best practice in equipment performance (productivity, maintenance and safety) step 2 is to brand the mine as æbest practiceÆ by sharing what has been confidential performance and outcome information with the general industry.Previous research has shown that many professional people are attracted by the prospect of a high achieving site because of the learnings and the support for continually doing better. In addition, a link has been established in previous research between productivity and safety. Operators and drivers are attracted to sites which have fewer dangerous people operating or driving. Good management delivers exceptional performance and a work site which high caliber managers and operational personnel people want to work at. The strategy requires commitment and proper execution but it can work. The strategy needs a specific approach and this paper will discuss this. A case study is provided from a mine which over a nine month period increased dragline performance by 15 per cent and reduced stress on the boom by 30 per cent. This mine paid the employees (professional and operational) $25 000/a less than the major mines but the operators and professional people would not leave; in fact, people were happy to be paid less to work there.CITATION:Lumley, G and Trott, T, 2012. Using best practice operations as a strategy for attracting and retaining professional people, in Proceedings International Mine Management 2012, pp 35-52 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 20, 2012

By J Harding, S Munro, R A. Bearman

Despite the importance of the primary crushing stage, performance optimisation is not well analysed with sufficient focus to give improvement opportunities. At the Newcrest owned Telfer operation, liner life plays an important part in scheduling planned maintenance. Major consideration is given to monitoring crusher performance, as the highly abrasive nature of the feed significantly impacts the liner wear life. A study was undertaken by the lead author which focused on establishing a strong baseline of accurate data pertaining to the performance of the crusher, in terms of, operating parameters, liner life and key machine design factors. As part of the study, mining feed materials were examined for a particular set of liners and this revealed that improved methods should be pursued. Due to the competitive nature of the mining industry, the business solution to complex problems with long shutdown cycles should be streamlined to incorporate a non-operational modelling approach that is significantly more efficient than traditional online trial and error methods. In order to dramatically reduce the time and business risks, it was decided to engage services to model and simulate the liner life by varying main operational and mechanical factors. The key to all simulation work is gathering high quality baseline data. Such data allowed deployment of the Kinematic Crusher Model and validation of the model against worn 2D wear liner profiles. The proven model was then successfully deployed to predict operational values that defined crusher performance. To enhance the study, further investigation into a set of mechanical and operational simulations generated a sensitivity matrix measuring key performance parameters throughout the wear life of the liners. The study revealed throughput as a highly sensitive parameter and a change in eccentric throw provided the greatest improvement in extending liner wear life.

Aug 24, 2022

By B Roache, J O’Brien, M Gray

Admixture use in cement products is commonplace in the construction and mining industries. Many Australian mines have an operational concrete batch plant and stock hydration control and water reducing admixtures. The benefits of admixture use, especially in shotcrete is understood and well documented. Cemented rock fill (CRF) is used to fill stope voids and create stable vertical and undercut surfaces at some Australian mines. These mines generally mix rock fill with a slurry of cement and water without the use of admixtures. Recently published work on optimisation of CRF mixes has mainly focused on the strength increases associated with changes to the mix grading proportions by the addition of fines, but not focusing on the potential benefits of admixture use. Admixture use in CRF may be the simplest CRF optimisation method, as the admixtures will often be added by the push of a button at the batch plant. A CRF testing program was undertaken to test the benefits of admixture use in terms of strength gain, using hydration control additives (HCA) and high range water reducer (HRWR) admixtures. Rock fill gradings were strictly controlled in the test process to allow clear definition of the difference admixtures provide in compression at 28 days. The testing results define admixture associated strength gains in a 6 per cent general purpose (GP) cement by dry weight CRF mix (131 kg of cement/m3). Costings have been developed to allow a mine operator to understand the cost benefits of admixture use in CRF due to reduced operating costs. Operational efficiency advances and a suggested admixture implementation plan for CRF optimisation is offered.

Nov 29, 2022

Outline of situations when valuations required - from capital raisings and takeovers, stamp duty, rates and capital gains tax, to probate and litigation between joint venture parties. Definition of types of exploration and mining properties as background to discussion on what methodologies to use (from grass roots to operating mine). Discussion on nature of alluvial deposits in New Zealand and how their characteristics and tonnage/grade uncertainties affect choice of methodology. Assessment of risk factors in New Zealand û technical, financial and socio-political (legislation, access, Maori land rights, environmental). Discussion of appropriate methodologies.

Jan 1, 1992

By B Belle, M Biffi

Cooling of coal mines in the Bowen Basin, characterised by steep geothermal gradient, is presently achieved mostly through rental surface bulk air cooling in summer months. This paper argues that future mines will be required to focus their cooling resources more intensively to manage a challenging thermal environment where virgin coal temperatures of over 50¦C at a depth of 500 m are expected. Currently, mine cooling systems are employed to maintain the wet bulb temperatures (WBT) to below 27¦C at which point the risks of heat stroke or other heat-related issues are manageable. The capacities of these systems are in the range of 6 MWR to 10 MWR. The relationship between high working temperature environments and injury frequency rates is well established. Therefore, provision of appropriate cooling strategies and understanding their optimum performance and suitability are important to Australian coal mines of the future. This paper evaluates the underground temperature profiles of deep, gassy coal mines with propensity for spontaneous combustion and proposes the long-term cooling pathways to effectively manage thermal hazards. Thermodynamic modelling is performed on a longwall face and includes air leakage effects from goaf streams at various locations along the longwall face. The strategy summarises the application of underground bulk air cooling, chilled water sprays on the shearer and the resulting temperature profiles. Considering the new mining projects planned for the Bowen Basin region, a review of implementable cooling strategies such as mid-gate mobile bulk air coolers (BACs), spot coolers, underground bulk air cooling and the use of chilled water to enhance the positional efficiency of cooling plants, are discussed in this paper. Finally, the comparison of ærentalÆ versus æownershipÆ of cooling plants is analysed as part of long-term cooling strategies.CITATION:Belle, B and Biffi, M, 2013. Cooling pathways for deep Australian longwall coal mines of the future, in Proceedings The Australian Mine Ventilation Conference , pp 223-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The development and distribution of gold placers in Otago û Southland is related primarily to the evolution and architecture of three distinctly different drainage networks that developed during and since Gondwana breakup: +        Late-Gondwana û Pre-marine; +        Middle Tertiary Post-marine; and +        Modern. Late Gondwana û Pre-marine drainage was dominantly recti-linear and controlled by normal faults and sedimentary basins formed before or during Gondwana breakup. Placers formed dominantly in 2nd order transverse drainages with primary sources in their catchments. This drainage network was progressively destroyed by inundation and burial by marine strata during Late Cretaceous û Middle Tertiary marine transgression that ultimately covered most of New Zealand. Middle Tertiary Post-marine drainage evolved on and incised the newly emergent low-relief landscape during regional marine regression driven by development of the present plate boundary through South Island. Most of Central Otago was drained into Southland and to the southern coast via a large braided river system with an extensive network of tributaries in its Central Otago reach. East Otago was drained by several smaller systems. Placers formed dominantly in proximal and medial reaches of 1st and 2nd order drainages with primary or pre-existing placers in their catchments. This drainage network was destroyed by inundation and burial of the Central Otago reach of the major system by lacustrine strata following tectonic damning of its middle reach by range uplift and development of a lake complex that covered >5000km2 of Central Otago. The Modern drainage network evolved from the Middle Tertiary network through complex response, firstly to uplift of NW-trending and NE-trending ranges throughout the region since the Late Miocene, and secondly to the effects of major Pleistocene glacial advances in West Otago. Placers formed in alluvial fans at range margins, proximal and medial pre-glacial fluvial systems and glacial outwash sequences. Evolution of each of these drainage networks has been accompanied by widespread sedimentary recycling of alluvial gold from older to younger placers, augmented locally by input of first-cycle gold derived from erosion of primary sources in the repeatedly exhumed basement rocks.

Jan 1, 2006

By P Minkkinen, J Lohilahti, T Korpela, B McPherson

Concentrator plants intake the ore from the mine and produce concentrates by extracting valuable minerals in a succession of process steps. Controlling the extraction process and detecting changes in the process requires updated information on a minute basis. Moreover, due to economical reasons, one must also collect metallurgical samples on a daily basis for monthly reporting.In this paper, we present how slurry samplers were installed in a Cu-Ni flotation plant to accomplish the aforementioned tasks. An on-stream elemental analyser at the plant is used for flotation process control by taking samples from selected process streams. Two process streams, the flotation feed and tail, are also equipped with metallurgical samplers. The metallurgical samplers were designed to have low head loss, be robust and easy to maintain and to collect slurry samples in a reliable way for the metallurgical accounting.Samples were collected by different sampler types and we discuss the uncertainty arising from sampling in the assays. Variographic analysis was carried out on the process data in order to find periodic components in the process, and estimate the correct number of shift sample increments and measurement error components. The metallurgical samplers were proven to be reliable devices with zero downtime and no sanding issues in the main process flows. In addition, we show that the tail measurement is the most important one for the plant recovery calculation, which emphasises the importance of the sampling accuracy in the tail stream.CITATION:Lohilahti, J, Korpela, T, Minkkinen, P and McPherson, B, 2014. Analysis of slurry sampling arrangements at a froth flotation plant, in Proceedings Sampling 2014 , pp 91–98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By K Verbeken, D Seveno, A Maslov, I Bellemans

Recycling and decarbonisation current metallurgical processes is key for our planet’s future and in both cases, digital twinning will play an important role. However, the various modelling techniques being used for digital twinning require a lot of input values on variables such as viscosities, diffusion coefficients and surface energies that need to be known as a function of temperature, atmosphere and composition, but which are not widely available, such as in databases, for molten slag phases. The need for more accurate data on physical slag properties is clear and will be extremely relevant for making more realistic and quantitative simulations. Some of these properties are difficult to determine, which is inherent to the very high pyrometallurgical temperatures. Therefore, this work focuses on some aspects related to determining electrical conductivities, viscosities and surface tensions of slags via a combined experimental-modelling method. Besides experimental work, molecular dynamics (MD) simulations can be used to investigate oxidic slag physical properties. With MD simulations, one can follow the time evolution of a system (consisting of atoms or molecules) by integrating Newton’s equation of motion. The input for an MD simulation mainly consists of a force field as well as initial positions, velocities and mass of each atom. The determination of the transport properties in existing literature of MD simulations in oxidic systems, is typically based on incorrect assumptions. For example, to determine the ionic conductivity, the frequently-used Einstein-Stokes equation fails to take into account all ionic types and neglects correlated motion. Furthermore, the viscosity determination via the Einstein-Stokes formula also assumes independent motion of the different ions. This paper gives a brief overview of the opportunities and challenges related to the use of MD simulations for oxidic slag systems.

Jun 19, 2024