Search Documents

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant' have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh's work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-' and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

By R. O. Williams

A recent article by Chernock, Singer, Mueller, and Beck 1 which supports the use of the integral of I sin $ d$ for comparing fiber texture data does not settle what happens to I sin ø as ø approaches zero, where I is the diffraction intensity for poles oriented 0 deg from the fiber axis. They indicate that they believe that it should approach some constant value (that is, I increases without bound) and the fact that in reality it does not was a result of the diffraction

Jan 1, 1960

By Austin E. Dwight

IT has been shown by Oelsen and Wever' that the effect of a solute element on the allotropic transformation in iron is dependent upon the quantity

Jan 1, 1957

By AIME AIME

COMMITTEES. CENTRAL GENERAL COMMITTEE.-Wm. Fleet Robertson, Chairman; Win. M. Brewer,. Secretary. LOCAL COMMITTEE OF NELSON, B. C.-A. S. Farwell, Chairman; W. C. Bayly, Secretary; William Blakemore, M. S. Davys, S. S. Fowler, R. R. Hedley, Leslie Hill, A. H. Telly; W. C E. Koch, J. J. Campbell. LOCAL COMMITTEE OF ROSSLAND, B. C.-His Worship Mayor Hamilton, Chairman; AV. H. Aldridge, Charles Biesel, H. H. Claudet, F. W. Guernsey, R. Marsh, J. W. Astley, R. W. Brock, A. A. Cole, A. G. Larsen, R. H. Stewart. Also the Rossland Board of Trade, Robert Hunter, President; K. E. Mackenzie, Vice-President; A. B. Mackenzie, Secretary. LOCAL COMMITTEE OF GRAND FORKS, B. C.-His Worship Mayor Hammor, Chairman ; A. W. B. Hodges, A. L. White, G. M. Fripp, L. A. Manley, W. T. Spier, G. W. Wooster. LOCAL COMMITTEE OF VICTORIA, B. C.-Wm. Fleet Robertson, Chairman; William Al. Brewer, Secretary; Harold Grant, Thomas Kiddie, Clermont Livingston, E. C. Musgrave, W. J. Sutton, Francis A. Thomson. LOCAL COMMITTEE OF VANCOUVER, B. C.-C. F. Jackson, Chairman; His Worship Mayor F. Buscombe, J. J. Banfield, A. Bethune, John Boyd, H. C. Clarke, A. B. Erskine, E. P. Gilman, William Godfrey, W. D. Haywood, R. K. Houlgate, H. T. Lockyer, J. I. McAdam, H. M. McDowell, C. W. McMeekin, W. H. Malkin, F. Richards, T. J. Smith, George A. Walkem, G. Slieldon Williams. LOCAL COMMITTEE OF WHITE HORSE, Y. T.-Robert Lowe, Chairman.; T. W. Jackson, Secretary; George -Armstrong, A. L. Bindley, Rev. Father Corbeil, L. De Gex, A. E. Fisher, W. P. Grainger, P. D. McMillan, Rev. Mr. Main, George C. Mallot, Alfred Parre, George Pulham, George Reid, William Robinson, J. P. Scharschmidt, J. C. Schraeder, Major A. E. Snyder, Rev. Mr. Stringer, Judge George L. Taylor, William Taylor, H. Wheeler, E. J. White, J. P. Whitney;' ; LOCAL COMMITTEE OF DAWSON, Y. T.-Hon. W.W. B. McInnes, Commissioner of the Yukon Territory, Honorary Chairman; Major Z. T, Wood, Assistant Commissioner of the Yukon Territory, Honorary Chairman; J. B. Tyrrell, Chairman; J. Moore Elmer, Vice-Chairman; George Black, Secretary; Hon. Mr. Justice Dugas, Hon. Mr. Justice Macaulay, Hon. Mr. Justice Craig, Dr. Alfred Thompson, D. A. Cameron,. E. W. Griffin. The first session, held in the ministers' room of the Parliament Building, 3 p.m., Saturday, July 1st, was presided over by Past-President Robert W. Hunt. His Excellency the Lieut.-

Nov 1, 1905

By K. Takahashi, I. Iwasaki

it is well known1 that racemic mixtures of optical isomers can be separated by passing their solutions through a column packed with r- or 1-quartz powder so that one of the isomers becomes adsorbed selectively on the asymmetric quartz surfaces. Although the natural occurrence of r- and 1-quartz is more or less equally distributed, some localities show enough deviations toward a higher proportion of l-quartz2 to suggest that optical isomerism might influence quartz flotation. Beta-amines have an asymmetric carbon atom, and therefore optical activity may be expected. Beta-amines are reported to behave quite differently from alpha-amines in the flotation upgrading of certain oxidized iron ores.3 It is of interest, for both practical and theoretical reasons, to determine whether or not optical isomerism plays a role in the amine flotation of quartz. In this article the results of Hallimond tube flotation tests and of adsorption measurements using d-beta-phenylisopropylamine on both r- and 1-quartz are compared. D-beta-phenylisopropylamine was chosen for the tests because it is commercially available in optical isomers. MATERIALS AND METHODS Brazilian quartz crystals were hand-sorted according to the difference in trigonal trapezohedral faces, and each crystal was further checked by the Airy's spiral.4 The respective crystals were then crushed, and the -150 + 200-mesh fractions were screened out for the Hallimond tube tests. The samples were cleaned by brief leaching with warm, dilute hydrochloric acid, and then by repeated rinsing with distilled water. In preparation for the adsorption measurements, they were then dry-ground in a pebble mill for several hours, washed a few times with distilled water, and finally dried in a vacuum desiccator. By means of the Krypton gas adsorption method, the specific surfaces of r- and 1-quartz samples were determined to be 27,700 and 19,800 sq cm per gm respectively, the difference being due mainly to the decantation procedure rather than to the inherent difference in their grindability. D-beta-phenylisopropylamine was the only collector used in the study. It was solubilized by neutralizing with 110% of the stoichiometric requirement of 0.1 N hydrochloric acid. The specific rotation of the d-beta-phenylisopropylamine was determined with a polari-meter using sodium D line to be, Although the d-beta-phenylis~prop~lamine showed absorption maxima in the wave length region of 250 to 270 millimicrons, due presumably to the phenyl group, these peaks were too sensitive to be used for colorimetric determination of the residual concentration in the adsorption measurements. The amine-picrate method, used in the colorimetric analysis of dodecylammonium chloride,' was found to work satisfactorily for the d-beta-phenylisopropylamine. The adsorption densities were thus determined after equilibrating 40 gm of the ground quartz sample with 300 ml of solution by tumbling in separate glass-stoppered Erlenmeyer flasks for one hour. EXPERIMENTAL RESULTS Fig. 1 presents the adsorption densities of d-beta-phenylisopropylamine on the r- and 1-quarts in the pH range of 6 to 7.5. In agreement with data reported in the literature, the adsorption density of d-beta-phenylisopropylamine was slightly higher on the r-quartz than on the 1-quartz, although the difference was not as pronounced as one might expect from the capacity of r-quartz and 1-quartz to separate racemic

Jan 1, 1969

By H. M. Chance

Jan 1, 1886

By Leo J. Vogel, E. D. Hummer, David J. Akers

INTRODUCTION An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contribute to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and

Jan 1, 1979

By C. J. Beevers

Tlze influence of zirconium hydride precipitate mprphology on the fructure of Zr-H alloys tested at strain rates of 10- sec at 20° and - 196°C and at strain rates of -500 sec.-1 at 20°C has been inves-tigated. The critical stage in the embrittlement of these alloys was the fracture of the zirconium hyhide precipitates to form large interval cracks at a stress of 25,000 10 137,000 psi. In specimens con-temping up to 100 ppm H the preciptates existed as isolafed platelets in the zirconium matrix and their fracture as enhanced by low temperature (—196°C) and high strain rate (-500 set-f) loading. These resl~lts lead to the conclusion that the rate of strain hardening of the zirconium metal controls the frac-tzrm of the hydride platelets. Increased hydrogen contents of 500 to 2000 ppm resulted in an increase in the 1)volume fraction and size of precipitates and crlso led to crack propogation in the hydride at both 20 and —196C at the low strain rates (10'* sec-'). Quenching led to refinerment of hydride precipitate size and reduced the degree of embrittlement at — 196°C; this effect is attributed to the absence of fracture of the fine precipitates. The formation of zirconium hydride precipitates has been shown to be the cause of hydrogen embrittlement of zirconium.' Several investigators'-" have studied the problem in broad outline, demonstrating that impact-loading conditions, testing temperatures below room temperature, and increasing hydrogen content produce increased brittleness. For example, Muehlenkamp and schwope2 showed that the transition temperature for notched impact tests was raised from 150" to 350°C on increasing the hydrogen content from 45 to 490 ppm. The degree of embrittlement is also controlled by the morphology of the zirconium hydride precipitates. The solubility of hydrogen in zirconium decreases from 600 ppm at 550°C to 10 ppm at 20"C,~ so that the form of the zirconium hydride precipitates (ZrH2) can be modified by varying the cooling rate through the Zr-aZr + ZrH2 phase boundary.= Forscher showed that quenching a specimen containing 35 ppm H from above 315°C resulted in a reduction in area of 70 pct at -196"C, whereas slowly cooling from above 315°C resulted in a ductility of half this value. The role of the hydride precipitate in the fracture process has been examined by Young and schwartz6 and more recently by westlake.' From metallo-graphic observations on slowly cooled Zr-H alloys they have suggested that cracks are nucleated in the hydride precipitates by the interactions of twins in the zirconium metal with the hydride. The experiments reported in this paper show that crack propagation in the zirconium hydride precipitates is the critical stage in the embrittlement of Zr-H alloys. The factors influencing fracture of the hydride precipitates and crack propagation in the zirconium metal will be related to the problem of embrittlement. EXPERIMENTAL TECHNIQUES The zirconium used in these experiments was produced from an ingot of vacuum arc-melted iodide zirconium forged down to 1 in. diameter at 800' to 850°C. The 1-in.-diameter bar was surface-machined and cold-swaged to 0.375 in. diameter. After a vacuum anneal at 800°C for 1 hr the hardness was 60 to 70 Vdh. The total impurity content was approxi-

Jan 1, 1965

By Arthur Notman

THE raw material men in all industries, and copper is no exception, are accustomed to think of them- selves as the whole show, and not without justice, for if there were no copper mines the world would have no copper. Nevertheless, many different things costing money and resulting in profits must be done to their product before it is ready for the world's use. In other words, they are making the frequent mistake of Chinking in terms of partial costs. Nobody really uses electrolytic copper. Possibly that is why nobody seems willing to pay anything for it. The manufacturers, being canny, do not buy any more electrolytic than they feel that they can work up and sell profitably, although they like to make the raw material men Chink that they will take all that can be produced. This is a state of affairs that has aroused my sympathy and curiosity, and has induced me to study the financial history of the copper wire and brass industry of the country or such portion of it as publishes any records readily available to the curious minded. About 60 per cent of the electrolytic copper used in this country is drawn into wire and consumed by the electrical industries. The remaining 40 per cent is

Jan 1, 1926

By W. A. Forbes

OUR present-day geological surveys show that 36 of our States are underlain with bituminous coal, covering a total area of 496,709 square miles. The North American continent possesses 69 per cent of the world's coal reserves, with the United States alone having an estimated 55 per cent. The American coal reserves, in tons, are calculated to he about 3,500,000,000,000 tons, of which we have exhausted about 1 to 1 1/2 per cent. If this coal were mined at the rate of the 1918 production-a record output of 579;000,000 tons-it would not be depleted for 4,000 years. The more easily accessible and high-grade coals would obviously be consumed much before this; some estimates are 100 years. The natural progress of the nation's industries up to 1910 encouraged on every hand the development of new mines, especially where cheap and easy access to coal measures was coupled with short hauls to the consumer. Over-development resulted, which is perhaps today one of the fundamental causes for the many difficulties faced by the coal industry, which is highly competitive; about 70 per cent of the production cost is labor. Salient statistics for 1930, recently issued by the U. S. Bureau of Mines, follow:

Jan 1, 1932

How Mining Engineers Will Fare in 1977 Mining Education- The State of the Discipline Coal Mining Technologists are a New Force in the Labor Pool Trained Manpower Provided by Mining Technology Programs Putting New Engineers to Work-A Management Perspective

Jan 1, 1977

By L. A. Panek, F. D. Wang, M. C. Sun

A method of stability analysis of underground opening by the limiting equilibrium approach is presented. The Coulomb shear failure criterion is employed to find possible fracture surfaces and to evaluate the shear strengths along them. The normal stresses required for the calculation of shear strength, and the shear stresses for the calculation of total shear force along the fracture surfaces, are obtained by the finite-element method of plane-strain analysis. The factor of safety against Coulomb shear failure is calculated as the ratio of the shear strength to the shear force along a fracture surface, similar to the practice in slope stability analysis. Four shapes of openings are analyzed, with three ratios of horizontal lithostatic stress and four coefficients of internal friction. The critical fracture surfaces found by this method of analysis are consistent with the arching of roofs and slabbing of ribs commonly observed.

Jan 1, 1972

By E. W. Hart, W. R. Hibbard

The room temperature flow characteristics of a series of Cu-Cr alloys are found to be related to the amount and characteristics of the chromium-rich precipitate. The results are consistent with the theory of Fisher, Hart, and Pry, which considers the trapping to dislocation loops around precipitate particles. THE use of dispersed phases for hardening metals, particularly high temperature alloys, has been practiced for several years. Current theories describing the effects of dispersions on the basis of dislocation theory have been proposed by Mott and Nabarro.l-4 rowan," and Fisher, Hart, and Pry.8 These theories recently have been discussed by Hart,' who pointed out that the experimental data available for comparison with theoretical calculations for overaged alloys are confined to studies by Gensamer, Pearsall, Pellini, and Low,8 Shaw, Sher-by, Starr, and Dorn,9 and some hitherto unpublished data on Cu-Cr alloys which will be described herein. Certain difficulties were associated with the interpretation of the first two studies. Gensamer, Pearsall, Pellini, and Low were concerned principally with interparticle spacing and did not document particle sizes. Shaw, Sherby, Starr, and Dorn included all the data in their report which was necessary for the theoretical evaluation, but their study is subject to some question1" due to difference in prior history of various specimens and due to systematic differences in particle characteristics" which appeared to be associated with differences in the magnification of their microscopic examination. The current study was undertaken to obtain critical data in a manner which avoids some of these limitations. Specimens of eight Cu-Cr alloys remaining from a previous investigation'' were available in the form of 100 mil sheet of the compositions shown in Table I. At 200 mil this material had been previously an- nealed ½ hr at 1000°C, water quenched, and cold rolled 50 pct. Samples were further cold rolled to a thickness of 20 mil for a total reduction of 90 pct. Sheet tensile specimens of standard geometry with a gage length 2½ in. long and 0.20 in. wide were machined from this sheet. These specimens were then annealed in a dried N2-H2 atmosphere for the times and temperatures indicated in Table I. This anneal served two purposes: 1—to obtain a fairly uniform and nearly constant grain size of 0.015 to 0.022 mm average diameter, and 2—to precipitate a fairly uniform, nearly spherical over-aged dispersion of essentially pure chromium. A typical microstructure illustrating the grain size and the uniformity of the dispersion is shown in Fig. 1. A typical dispersion illustrating the range of sizes and shapes of the particles is shown in Fig. 2. The tensile specimens were tested in the Instron equipment described in ref. 11 at room temperature at a strain rate of 0.04 in. per in. per min. Three tests were run on each alloy with sufficient repro-ducibility that a single true stress-true plastic strain curve could be drawn through the three sets of data for each alloy. Typical curves are shown in Fig. 3.

Jan 1, 1956

The pellet plant, built by Dravo Corp, in Groveland, Mich., for the Hanna Mining Co., is now in full operation. Although using jasper, a type of iron ore with low iron content (approximately 28% Fe), the plant has a rated capacity of 1,250,000 tans of pellets per year. In its four years of existence, the nearby concentrating plant has seen its capacity increase from 700,000 tons to 1,500,000 tons a year as part of a major expansion program at Groveland. Utilizing the Dravo-Lurgi continuous grate process, the pellet plant produces %a-in. pellets of more than 60% iron content. The fully-hooded pelletizing grate, largest in the U.S., is 9 ft. 10% in. wide and 223 ft. 1% in. tong over 34 windboxes, with an effective hearth area of 2195 sq. ft. Drying, firing, and cooling functions are all carried out on this single piece of equipment.

Jan 4, 1964

Jan 1, 1969

By William M. Bowron

THIRTY years ago, when I stood on the cliff of red fossil iron-ore, on Red mountain, Jefferson county, Ala., I asked what were the geological relations of this remarkable deposit. In reply I was told that it was a limestone colored and saturated by some unknown but wholly external influences, and that at a reasonable distance from the surface the color would disappear. I could find no satisfactory explanation either of the nature of this wonderful external permeating influence, or of the cause of such a ferrous impregnation selecting this one particular bed of limestone, to the exclusion of the higher and lower beds of the same material which are not even stained. I. THE PRESENT THEORY. Referring to this subject, Dana says:' "The clays, clayey sandstones and limestones of the Clinton epoch, through New York and the Appalachians, show that the mud-flats and sand-banks, and hence the shallow seas of the coast region, still continued. . . The beds of argillaceous iron-ore, which spread so widely through New York and some of the other States, south and west, could not have formed in an open sea, for clayey iron-deposits do not form under such circumstances. They are proof of extensive marshes, and, therefore, of land near the sea-level. The fragments of crinoids and shells found in these beds are evidence that they were, in part at least, salt-water marshes, and that the tides sometimes reached them." At first, this explanation seemed satisfactory, but the more I studied the ore the less satisfying the explanation became. 1. In the ore itself I found associated with the small particles of rounded matter (now consisting of iron oxide in which organic structure, if ever present, has become lost, though the

Nov 1, 1905

By R. L. Grunes, F. K. Kies, C. D&apos, Antonio

THE several studies concerned with the annealing of thin nickel films have largely been restricted to films of a single thickness.1-4 It is well-known, however, that both physical and mechanical properties depend upon film thickness.5, 6 The strength-thickness relations found in vapor-deposited nickel films in the annealed and as-deposited states, as an example, are at least partially due to the density and arrangement of imperfections within the films.7, 8 For these reasons, the annealing characteristics of thin nickel films as a function of thickness were investigated. Electrical resistance was chosen to monitor annealing behavior since resistance changes are partially dependent upon defect structure. In addition, the equations predicting film resistivity as a function of thickness are already available.9, 10 Further advantages afforded by electrical-resistance measurements are its adaption to continuous readings during annealing and its relative simplicity. Nickel films were vapor-deposited, at average rates of 60Å per sec, on Vycor substrates held at room temperature in vacuums of about 10-5 torr. Afterwards, deposition-thickness measurements were made using a multiple-beam interferometric technique. A more detailed description of deposition procedures and the interferometer appear elsewhere.7, 8 The four-probe method was employed in measuring electrical resistance since this technique measures film resistance without contributions from lead wires and contacts. Resistance measurements were made before, during, and after annealing to temperatures of 700°C under vacuums of approximately 10-4 torr. Measurements were made every 25°C or more often when necessitated by unusual resistance changes. Cooling and heating rates were maintained at approximately 5°C per min. Typical resistivity vs temperature curves are shown in Figs. 1 through 4. It is apparent from these

Jan 1, 1965

By Lyon F. Terry

SPEED-UP of production of crude oil and its products, accompanied by rising prices and the organization of the industry on a war basis, featured the economic aspects of petroleum in 1941. Early in the year American tankers were urgently requested by the British to replace losses and offset slower transit under convoy. Some forty American owned tankers were first assigned to Britain and an additional forty-odd ships were transferred during the summer. This threatened to reduce our transportation facilities from Gulf ports to the Eastern seaboard below requirements, especially should sinkings have increased and the British needed more ships. Co-ordinator Ickes began preparations for restricting gasoline consumption in the Eastern district and plans were formulated for the construction of an emergency trunk pipe line from Texas to New York and Philadelphia refining centers, and for a gigantic tanker-building program. Sales of new oil-heating units in the East practically ceased. The companies were urged to transport as much oil as possible by tank car and by October 140,000 barrels of oil per day were reaching the East Coast district by rail, sufficient to meet 8 per cent of total requirements. But British sinkings from July through October decreased 63 per cent compared with the four months ended June 30, Britain began the return of tankers, the construction plans were dropped, and the threatened shortage was thus averted.

Jan 1, 1942

By B. W. Roberts, V. A. Phillips

A copper alloy containing- 25.5 at, pct Zn and 19.0 at. pct Ni, which was previously found to show an anoma1old.s hardening effect on quenching- from 600 "C and aging- at 400oc, has now been examined by neutron diffraction. No evidence of long-range order was found. The aged sample showed diffuse scattering- consistent with clustering. The anomalous hardening effect is now attributed to lattice strains caused by clustering rather than (long-range) order hardening. SOLID-solution Cu-Ni-Zn alloys (the commercial 'nickel silvers") have been reported to show anomalies in: change of resistivity on cold working,1-6 temperature coefficient of resistance,2-12 resistivity at low temperatures,13,14 parameter (vs temperature),2"4 calorimetric data,2,4 specific heat,15,16 dilation,2-4 and elastic modulus.17 The structure responsible for the anomalies is produced by annealing typically near 400°C and is rather loosely referred to as the ('K-Zustands" (K state), a term coined by Thomas1' who apparently meant simply that the arrangement of atoms on the sites deviated from that expected statistically. Thomas proposed that the K state occurred in a variety of (solid-solution) alloys such as Cu-Ni-Zn, Ni-Cr, Ni-A1, Ni-Cu, Fe-A1, and Fe-Si and is recognized because its formation is strongly temperature-dependent and results in an increase in electrical resistance which can then be decreased by cold working. Later workers on ('nickel silver" have interpreted the K state variously as short-range order, long-range order. or a combination. The present work was prompted by the discovery by Phillips and Jones19 of a substantial hardening effect when an 18 pct "nickel silver" alloy which is fairly close to the Cu2NiZn composition, was reheated in the range 150" to 450 C after previously quenching from 600°C or, alternatively. was slow-cooled from 600°C or above. The phenomenon was attributed to (long-range) order hardening. Due to the similarity in the atomic scattering factors of copper. nickel, and zinc atoms, the ''nickel silvers" are unfavorable for X-ray diffraction studies aimed at detecting ordering. Nevertheless Bialas et a1.,20 using a powder sample containing 47.96 wt pct Cu, 24.03 wt pct Ni, and 27.98 wt pct Zn, slow-cooled from 400" to 200°C taking 500 hr, observed weak super lattice lines. Further unpublished work" using an anomalous dispersion X-ray technique indicates that zinc atoms are regularly ordered at the corner points of the lattice cell, while the nickel and copper atoms are statistically distributed on the remaining sites. Köster 17 also observed X-ray superlattice lines, for example, in an alloy containing 43.5 wt pct Cu, 28.6 wt pct Ni, and 27.9 wt pct Zn superimposed on the basic fcc cell with a = 3.62 kX. He proposed a Cu3Au-type superlattice with the Ll2 structure in which the A sites were statistically occupied by copper and nickel atoms and the B sites by zinc. He adds that substitution must be possible so that zinc atoms partly occupy A sites. Below about 35 pct Cu, Koster had some evidence for a CuAu-type superlattice with the Llo tetragonal fcc structure with a = 3.82 kX, c/a = 0.88 which could be preserved by quenching. This is suggested17722 to correspond to CuNiZn. While the present work was in progress Hirabaya-shi et a1.23 made an independent comprehensive neutron-diffraction study of a single crystal containing 50.05 at. pct Cu, 26.57 at. pct Ni, 0.25 at. pct Mn, 0.13 at. pct Fe, balance zinc. The presence of manganese and iron is surprising since the crystal was supposedly grown from high-purity metals. The homogenized crystal showed evidence of long-range ordering after an anneal of 5 months at about 300°C. Three possible crystal models were proposed. A curious feature of their results23 is that they could not find any neutron-diffraction evidence of ordering in a powdered polycrystalline near-stoichiometric Cu2NiZn alloy. There appears to be some essential difference between a near-stoichiometric Cu2NiZn alloy and one somewhat further off stoichiometry as used by the present authors. Thus Sato14 was able to reproduce the low-temperature resistivity anomaly reported by one of the authors13 on the present alloy if he used a similar composition, but found the normal behavior of the residual resistivity in a near-stoichiometric alloy. satol2 found that the resistivity of a cold-drawn slightly off-stoichiometric alloy increased to a maximum on isothermally annealing at 300°C and then decreased ("over-aged"). Since he could not explain this on the basis of ordering phenomenon, he proposed that zinc atoms were segregating to stacking faults (Suzuki effect) and found etching bands on the surface by replication which were attributed to the widening of faults. Sato suggested14 that the hardening effect observed by Phillips and Jones19 is partly due to the Suzuki effect. EXPERIMENTAL The starting material was 1/4-in.-diam hard-drawn rod of a commercial 18 pct "nickel silver" alloy identical with that used in a previous study by Phillips

Jan 1, 1967

By E. S. Wheeler

The rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the last weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion-resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success. The successful production of castings of monel metal and nickel requires careful attention to molding practice, proper melting equipment

Jan 1, 1930