Search Documents

By L. D. Lash, J. R. Ross

Discovery of scandium in the Vitro solvent extraction plant for uranium led to commercial recovery of the byproduct. Micro amounts of scandium were extracted with uranium by dodecyl phosphoric acid, but failed to follow ura-niuminto the hydrochloric acid strip solution and were eventually concentrated in the organic extractant. A fluoride strip system was developed to recover scandium from the solvent in concentrated form. High purity scandium oxide was then prepared in multi-pound lots by chemical separation techniques. The plant recovery operation, final product purification, and analytical procedures are described. Scandium is a pseudo-rare earth which is truly rare and expensive. It has special properties which may make it desirable even at the present price of $2750 per lb. Recently the price was lowered from $5000 per Ib which had prevailed since 1952, and it is anticipated that usage will be stimulated because of the lowered price. This metallic element is distributed widely in trace amounts in the rocks of the earth's crust. In addition to micro-amounts found in most uranium ores, concentrations of 50 to 100 ppm have been found in Colorado ferberite ore, lateritic nickel ore, heavy sandstone from Utah, Wyoming, and New Mexico, and various zircon sands and monazites from the western part of the U. S. Scandium has been found as an essential constituent of very few minerals, the most important being thortveitite, a scandium silicate. At the present time, this mineral commands a price more than twice that of gold. Chemically, scandium is in group 3A of the periodic table. It is closely associated with yttrium and the rare earths which it strongly resembles in its reactions. It has a valence of three and will form an insoluble hydroxide, fluoride, or oxalate under proper conditions, similar to the rare earths. Eight years before its discovery, scandium was predicted by Mendeleef who ascribed his eka-boron with properties nearly identical to the actual properties of scandium. Its position as the element with Atomic No. 21 and Atomic Weight 44.96 places it between calcium and titanium in Period 4 of the chart. The successful commercial application of scandium must depend on unique properties to justify use of this high cost substance. Greater consumption would allow additional price reductions, but scan- dium will remain a relatively high-priced commodity because of its inherent scarcity. Research reportedly has been oriented toward use of scandium as an agent to achieve high-temperature, low-density alloys with magnesium and tantalum.' Also, the U.S. Air Force sponsored a project for production of research amounts of pure scandium metal.' The oxide has been used experimentally in electronics, ceramics, and metallurgy. The various aspects of scandium are well covered in recent publications.s-5 CONCENTRATE RECOVERY Small amounts of scandium exist in uranium ores and are dissolved during an acid leach yielding up to 0.001 gpl Sc2O9. When Vitro converted their uranium plant from phosphate precipitation to solvent extraction: scandium was found to follow the uranium into the dodecyl phosphoric acid solvent (DDPA). However, scandium did not strip with uranium from the DDPA in hydrochloric acid, but remained in the solvent. Therefore, a concentration of scandium built up in the organic phase. Residues from the solvent were spectrographed by the U.S. Bureau of Mines and found to contain scandium. As a result of this discovery, provisions were made in the plant for recovery of scandium-bearing concentrates. Solvent extraction of uranium was added to a conventional acid leach process in a typical installation? The ore was crushed and ground, and then leached with dilute sulfuric acid. Addition of an oxidant such as sodium chlorate insured conversion of uranium minerals to a soluble form. At this point, the slurry was chemically reduced by a sulfide, such as sodium hydrosulfide, to remove substances such as ferric iron and molybdenum which were partially extracted by the solvent. The solids-liquid separation was accomplished by a four-stage counter cur rent decantation (CCD) thickener circuit. The uranium was extracted from pregnant liquor with 0.1M DDPA in kerosene and stripped with ION

Jan 1, 1961

By R. E. Zimmerman

THE separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pct successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the -48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of -48-mesh slurries. These large scale operations have been recently described by D. H. Davis. 1 C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investigational work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investigational work as well as the results of experi¬ments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. METHODS OF CONDUCTING LABORATORY TESTS The bulk of the research work was conducted in the laboratory of the Champion No. r Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location

Jan 1, 1948

By Robert E. Cuthbertson

It is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson,= by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be corfined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. Brief History of Reagent Practice at Climax Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 19-20, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Nevertheless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1947

By Robert E. Cuthbertson

It is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson,= by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be corfined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. Brief History of Reagent Practice at Climax Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 19-20, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Nevertheless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1947

By Robert E. Cuthbertson

IT is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson3 by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be confined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. BRIEF HISTORY OF REAGENT PRACTICE AT CLIMAX Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium, cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 1920, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Never theless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1944

By E. F. Miller

The subject " Safe Timbering of Working Places in Mobile Loading" is one that requires an analytical study of the strata both above and below the coal seam as well as the characteristics of the coal seam itself. The projection or mining plan must be based on economic roof control in which the application of timber can be minimized without incurring cost increases in other phases of production. The several types of loading machines in common use today are not adaptable to the same projections or timbering systems. Consequently the type of equipment to be used must also be considered. For these reasons the writer does not believe that the problems of timbering in working places can be discussed without simultaneously considering economic production as well as the safety of men and the conservation of equipment. Prior to the introduction of loading machines as a substitute for the pick and shovel system of loading coal, the care and maintenance of the individual working places were generally the responsibility of the coal loaders who worked in them. Up to that time very few coal companies had developed and applied fixed and definite standards for timbering the working places in the mines they operated. It is common knowledge that mechanical loading of coal has had several false starts in the last twenty-five years and it is only in the last decade that it has developed to the stage at which we now find it. During this twenty-five year period the management of the more responsible companies have come to realize the tremendous importance of roof control in coal mining. From a safety viewpoint, the lack of roof control has been and still is responsible for more than a third of the industry's annual fatality experience. In recent years workmen's compensation and insurance rates have steadily increased while the profit margin has decreased almost to the point of elimination. From an economic operating viewpoint, the failure to properly control roof is quite often the most costly single phase of coal mining. Since the manufacturers of loading machine equipment have so improved their machines that normal care and maintenance can reduce to a minimum the time lost because of mechanical failure the production delays from other causes have assumed a far greater importance. Roof control in the broad sense and in the light of concentrated mining plans or projections that are adapted to mobile loading should be regarded as one of the major problems in the inseparable phases of production and safety of the workman and equipment at the working face. The subject of this paper cannot be treated properly unless what is said here is based upon the broad and fundamental problem of genera' roof control. The suc-cessful solution of a problem arising in any industry must have its origin in a complete analysis of the known facts or factors that pertain to it. The several illustrations

Jan 1, 1949

By H. S. Price, J. C. Cavendish, R. S. Varga

This paper presents a new technique for solving some of the partial differential equations that are commonly used in simulating reservoir performance. The results of applying this technique to a simple problem show that one obtains accurate pressure values near wells, as well as accurate pressure pdients, which can be explicitly calculated. The method is completely rigorous in that convergence of the discrete numerical solution to the continuous solution for both pressure and pressure gradient is established. High-order, piecewise-polynomial approximations are used near the wells where pressure gradients are steep, while low-order, piecewise-polynomial approximations are used elsewhere to reduce greatly the calculation time. This combination is shown to give a uniformly good approximation to the solution. These approximations, obtained by using a Galerkin process with suitable Hermite subspaces, are shown to be theoretically and numerically superior to the usual approximations obtained from standard finite-difference techniques. Not only are much greater accuracies obtained, but computer times are also greatly reduced. The application of this technique to multiphase flow problems (e.g., single well coning problems) would have considerable practical interest, but such extensions of this technique with full mathematical rigor have not been made as yet. However, the numerical methods presented here are general, and in principle extend to multidimensional, multiphase flow. Moreover, the preliminary results given in this paper are sufficiently encouraging that we feel the effort in attempting these extensions is justified. INTRODUCTION The problem of obtaining accurate pressure distributions and pressure gradients around wells is of considerable importance in the numerical simulation of reservoir performance. The most common approach to solving this problem is to use finite difference techniques (see McCarty and Barfield9 or Peaceman and Rachfordl0). This approach, however, has many disadvantages, the major one being that many grid points are generally necessary for accurately describing the pressure distribution and the pressure gradient around wells. This need for a fine grid results in large computer times and often in prohibitively high costs. Besides investigating the method of finite differences, some authors, such as Welge and weber17 and Roper, Merchant and Duvall,13 have considered a combination of analytical and numerical techniques with some success. These approaches, however, are all nonrigorous and quite often cannot even be applied. In this paper, we present a numerical formulation of high-order accuracy, based on the Galerkin method, for solving this problem. We treat here only the partial differential equation that describes steady-state, single-phase flow. However, the methods presented are general and in principle extend to multidimensional, multiphase flow. Specifically we treat special cases of the problem in two dimensions described by: where G is a rectangle (with sides parallel to the coordinate axis) with boundary ?G, ?/?n denotes the outward normal, and y and B are non-negative constants such that y + B > 0.

Jan 1, 1970

By Richard H. Sprute, Dennis J. Kelsh

Slow-settling, fine-grained suspensions can often be dewatered and densified by applying direct current between buried electrodes. Although water removal rates and power expenditures depend on physical and chemical properties of the treated slurries, metal mine tailings from Idaho, Colorado, and Mexico have responded well in laboratory testing, as have 29 samples of ultrafine coal waste from mines in nine states. This Bureau of Mines report reviews field tests at two Idaho metal mines and describes the recent installation at the Henderson molybdenum mine near Empire, Colorado, and the treatment of coal sludge at a Clinchfield Coal Co. preparation plant near Dante, Virginia.

Jan 1, 1980

J. L. CHRISTIE, Chairman T. S. FULLER, Past-chairman W. M. PEIRCE, Vice-chairman W. A. SCHEUCH, Vice-chairman E. M. WISE, Secretary International Nickel Co., Bayonne, N. J. W. M. CORSE, Treasurer Executive Committee H. A. BEDWORTH G. O. HIERS D. K. CRAMPTON R. H. LEACH E. H. DIX, JR. R. F. MEHL J. A. GANN J. WALTER SCOTT' JEROME STRAUSS Finance Committee T. S. FULLER, Chairman W. M. CORSE H. S. RAWDON C. H. MATHEWSON SAM TOUR

Jan 1, 1934

By Renato G. Bautista, Theodore D. Tiemann

A kinetic study of the hydrogen reduction of taconite from the Wisconsin Gogebic range was made over the temperature range from 500° to 1000°C on eleven size fractions from 4 to 150 mesh. Two stages of reduction were observed, a rapid initial reaction followed by a slower reaction presumably taking place at an internal receding FexO-Fe interface. Calculated mean activation energies for the two reactions were 7800 and 14,600 cal per mole respectively. In recent years there has been an increased interest in the direct reduction of iron oxide ores to metallic iron by means of gaseous reducing agents such as hydrogen and carbon monoxide.1,2 These investigations have been motivated by the desire to develop a process that will by-pass the blast furnace in the production of steel. The majority of these processes have been developed to produce metallic iron by direct reduction from high-grade iron oxide ores.3"5 Very little work has been done on the low-grade siliceous iron oxide ores.6"8 The work reported here is directed principally towards the fundamental aspect of the reduction reactions of siliceous iron oxide ores, since the practical aspects of the gaseous reductant process were discussed previously. The ore used in the investigation was obtained originally from the United States Bureau of Mines10 trench sample of the Yale member of the Wisconsin Gogebic range iron formation. The Yale taconite has an average analysis of 28.2 pct Fe and approximately 50 pct SiO2. Chemically, these nonmagnetic taconites contain on the average about 53 pct silica and 30 pct Fe. An average analysis calculated fron the USBM10 figures for a composite of the five members (Norrie, Plymouth, Pence, Pabst, and ale) of the iron formation is given in Table I. Mineralogically, based on previous X-ray diffraction and other studies, the principal minerals are hematite (Fe2O3), geothite (Fe2O3.H2O), and quartz (SiO2). Minor amounts of iron containing silicates, siderite (FeCO3) and magnetite (FeO. Fe2O3) are present.10,11 The iron minerals and the quartz are finely disseminated requiring extremely fine grinding for liberation. For the experimental work, the ore sample was screened into a number of size fractions, the analyses and densities of which are given in Table II. EXPERIMENTAL PROCEDURE The reduction experiments were carried out in a 24 in. by 2 in. ID nichrome-wound vertical-tube furnace mounted on a stand. A 1 1/2 in. OD zirconium-oxide combustion tube was used inside the furnace to contain the atmosphere. To the top of this combustion tube was joined a pyrex ground-glass joint to which was attached a glass bulb with a small (1.0 mm) opening at the center, and with two outlets controlled with a stopcock on each side. A pyrex-glass joint with connections to three stopcock joints for introducing hydrogen, nitrogen, and mixtures of hydrogen and nitrogen gas was joined to the tapered bottom of the combustion tube. The sized ore fractions were contained in a 1 in. diameter by 1 1/2 in. 150-mesh nickel screen basket. The basket was suspended in the furnace from a balance by means of a supporting nickel wire which hung freely inside the combustion tube. The furnace temperature was controlled by a Leeds and Northrup Speedomax Type G controller, connected to a chromel-alumel thermocouple placed

Jan 1, 1962

By John E. Conley

THE slate industry of the United States has shown a marked decline in value of products made annually since the peak year 1925, although there has been moderate improvement over the lean years 1932 to 1934. In 1940, the value of all slate products sold was approximately 5 3/4 million dollars for a total output of 473,450 short tons. The quantity sold was a little less and the value a great deal lower than the annual averages for the past two decades. Enormous quantities of waste materials result from the quarrying, splitting and milling of slate. Obviously, utilization of such waste material is desirable, not only from the viewpoint of economical operation but also for the purpose of conserving natural resources. One possible use is to produce expanded or puffed lightweight aggregate for use in concretes. Such concretes are strong enough for specific uses, and the advantage of lightness could be obtained in such structures as the walls and roofs of buildings, suspension-bridge roadways and various other applications where weight is a factor. Conceivably, these uses could consume an appreciable annual tonnage. USE OF WASTE SLATES FOR MAKING AGGREGATES The lightweight-aggregate industry has been discussed elsewhere4.5 and need not be covered in detail in this paper. The materials commonly utilized are naturally occurring aggregates such as volcanic cinder, tuff and pumice; by-product materials, such as ordinary cinders and air-cooled slags; and the specially manufactured products, including Haydite, Pottsco, Gravelite, Cel-seal, Superock and Waylite. Slates, however, have not been given the consideration they merit, especially in the United States. In the British Isles, some work has been done' on certain Welsh slates by the Building Research Station to stimulate the use of these wastes. REQUIREMENTS FOR RAW MATERIALS As pointed out by Hughes,4 the lightweight-aggregate industry is segregated in regions adjacent to large cities in order to localize the market and avoid the necessity of long freight haulage. Waste slate from the deposits of eastern Pennsylvania, northern Maryland, and Virginia would meet the basic requirement of any low-priced structural raw material. One apparent advantage is attained when slate waste, normally discarded, is utilized in the manufacture of a by-product. Mining or quarrying costs usually have been assessed against the main product. Some additional grinding might be desirable, but this operation would be relatively cheap, as most slates grind easily. It is believed that virtually all slates, when properly heated, will expand to some degree. However, types that will expand from 3 to 7 times their original volume are preferred. Fig. I illustrates the expansion of a Pennsylvania slate. The cube originally

Jan 1, 1942

By R. P. E. Hermsdorf

THE electrolytic refining of metals for the removal of undesirable impurities has become a recognized necessity in the nonferrous field. Copper, lead, zinc, nickel, silver and gold have been produced in this manner for years. The United States Metals Refining Co., realizing that considerable quantities of lead and tin could be made available to the trade if a satisfactory method of purification of these metals could be established, decided to investigate the possibilities of electrolytic solder. In cooperation with Dr. Edward F. Kern, of the School of Mines at Columbia University, the company developed a process of electrolytic refining of lead-tin alloys using a tin-lead fluosilicate electrolyte. A pilot plant was installed in November, 1927, and the commercial unit was put in October, 1929. Since that time thousands of tons of electrolytic solder have been produced in this plant and consumed by all branches of industry that use solder.

Jan 1, 1936

By L. Weyher, H. L. Lovell

This discussion is restricted to a very specific application of the cyclone - its use as a hydro-cyclone in the cleaning of fine coal. It is hoped that the development of the present data will assist in the further elucidation of existing qualitative models, and also in an enhanced application of the hydrocyclone and provide a base for further research. Discussed are the mechanisms of gravity separation in hydro-cyclones, test procedures, experimental observations, and industrial applications from these studies. Within the general area of unit operations, a considerable effort has been expended in theoretical and empirical research associated with cyclone operations. The motivation involves the industrial requirement for devices and techniques to manipulate small particles at low operating costs, a situation required in coal preparation. There are good reasons why the cyclone helps to satisfy this demand, because it combines operational simplicity (no moving parts) with versatility and high throughput capacity per unit area. The cyclone is one of the most widely applied tools in the process technologies. There are areas for potential cyclone application which have been only meagerly explored or not considered at all. This discussion is restricted to a very specific application of the cyclone - its use as a hydrocyclone in the cleaning of fine coal. It represents an initial presentation of a more comprehensive report. Coal preparation can appropriately claim the hydrocyclone since most of its predominant industrial uses have originated in this area and have spread into other applications, including the broad field of ore dressing, the petroleum industry, chemical processing, nuclear engineering and food technology. There is one operational principle common in all cyclones: A fluid is tangentially introduced into a cylindrical or conical container under pressure. A predominantly irrotational flow field1 is established within the cyclone (Fig. 1). The uniqueness of this flow is indicated by the variation in tangential velocity across the cyclone radius, which reaches a maximum a short distance from the center and decays toward the cyclone wall. In contrast, the tangential velocity in a centrifuge increases uniformly toward the wall. Usually two products are discharged from the cyclone. They differ in that one discharge consists predominantly of that portion of the feed fluid which moves along the wall axially away from the feed inlet, while the other consists predominantly of fluid spiralling along the central regions of the cyclone, in an axial direction opposite to that of the wall current. Fig. 2 indicates these discharge points schematically. The latter product may be termed the vortex-product, since it is discharged with the central vortex-current. In the case of conical cyclones, the former product may be referred to as the apex-product. Although the names "over- and underflow" are widely used, many cyclones are operated from extreme angular positions thus the proposed terms are less ambiguous. The cyclone feed fluid can be laden with solid particles or nonmiscible fluid drops. Such a feed component is discharged from the cyclone, after some residence time, into the one or the other product. Yet, the orifice through which a particle will leave the cyclone is dependent upon a number of factors. These factors, in a statistical sense, determine the path of the particle within the cyclone. Thus, different separation phenomena are possible and different process results attainable by the controllable variation of the particle path. It is then, to attain a fuller understanding of this particle path, to which this study is ultimately directed. It is anticipated that the detailed study of the data being developed will allow further elucidation of existing qualitative models. However, the development of a quantitative description of cyclone operation in terms of a mechanism is not currently feasible. The flow conditions in a cyclone are not fully understood even for a pure fluid, without the added complexity of the inclusion of multiple size-density particles. It is hoped that the development of the present data will also assist in an enhanced application of the hydro-cyclone and provide a base for further research. Some practical applications drawn from the data are suggested. Cyclone operations have been classified according

Jan 1, 1967

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By Gen-ichi Nakazawa, Masamichi Fujimori, Ichiro Doi

INTRODUCTION The major products of nickel industry in Japan are the electrolytic nickel (E-Ni), the ferro-nickel (Fe-Ni) and the nickel oxide sinter (NOS), totaling in production to 90 - 100 X 103 tons/year in terms of pure nickel content, and sharing approximately 20% for E-Ni, 10% or less for NOS, and the rest for Fe-Ni. The raw materials to be used for these products depend totally upon the imports from abroad; matte, the raw material used in the production of E-Ni, is from Australia and Indonesia; matte for the NOS is from Indonesia and New Caledonia; and garnierite, the raw material for Fe-Ni, is imported in bulk from New Caledonia, Indonesia and the Philippines. This report describes the acquisition of these raw materials, the production processes, trend of supply-demand, problem areas and the measures taken, and so forth, in connection with the nickel industry in Japan. ELECTROLYTIC NICKEL 1. History The nickel industry in Japan began in 1939 by the Sumitomo Metal Mining Co., Ltd. (SMM) with 150 tons E-Ni/month under the blast furnace smelting and the metal anode electrolysis. This was temporarily suspended after the end of last World War II, but resumed in 1952 with garnierite of New Caledonia as a raw material. Since then, the production capacity has been expanded incidentally to the increase of demand. However, since the smelting of garnierite contained about 2% nickel was very costly, the smelting process had been changed to smelt the briquettes of the mixture of garnierite and nickel sulfide concentrate imported from Canada and Australia. In 1975, this smelter was closed, and SMM's nickel refinery used matte from Western Mining Corp. (WMC) of Australia as a raw material. The refining process had been the metal anode one. The crude nickel oxide derived from roasting the high grade nickel matte had been melted and reduced with coke in the electric furnace and cast into anode. In 1970, a new refinery was constructed to produce 1,000 tons Ni/month under the matte anode process, and further, in 1976, the old refinery was converted into the matte anode process, thus resulting in the total production capacity of 1,690 tons Ni/ month today under the matte anode process. Shimura Kako Co., Ltd. began in 1951 to produce a little of E-Ni, and in 1955, they constructed a shaft furnace smelter with New Caledonian garnierite as a raw material to begin the E-Ni production under the matte anode process. Its monthly production reached 400 tons in 1957, but it discontinued its smeltering in 1963 to convert to the matte import from S. Le Nickel, WMC and INCO. In 1979, it changed the source of matte supply from the above to Soroako of Indonesia, discontinued the E-Ni production in 1979, and arranged for a total toll contract with Sumitomo. Meanwhile, SMM has developed a very distingished process for nickel-cobalt separation and refining by a solvent extraction method from nickel and cobalt mixed sulfide generated as a by-product in the nickel recovering process from laterite under the Nicaro process. Nippon Mining Co., Ltd. (NMC) also developed its own process. The plants under these processes were constructed in 1975, with the monthly production capacity of 230 tons of nickel and 130 tons of cobalt by SMM, and 300 tons of nickel and 110 tons of cobalt by NMC. SMM imports the raw material from the Marinduque Mining and Industrial Corp. of the Philippines, while NMC from Queensland Nickel Pty. Ltd. of Australia. 2. Production Status 2.1 Producers and materials Today, SMM holds the monthly E-Ni production capacity of 1,920 tons, of which 1,690 tons are from the matte anode process, and the remaining 230 tons are from the mixed sulfide as a raw material. NMC also uses the mixed sulfide as a raw material for a production of 300 tons/month. [ ] Most of SMM's raw material, nickel matte, is imported from WMC of Australia, partly using the Soroako matte from Indonesia. An example of material analysis is given in Table 1. Matte is a raw material for E-Ni and NOS, and the major sources of matte supply at present are Australian WMC and Indonesian Soroako, occupying ap-

Jan 1, 1982

By P. G. Winchell, A. J. Heckler

An experimentally simple method for determining the effect of alloying elements on the activity of carbon is validated in Fe-Ni-C austenite. The technique consists of the equilibration of carbon between specimens of different nickel contents within a sealed silica capsule. The attainment of carbon equilibrium within each capsule is evidenced by: 1) in each capsule specimens of the same nickel content attained the same final carbon content regardless of their initial carbon contents, 2) in every capsule the final carbon content was reached for most nickel contents by carburizing and by decarburizing. The activity of carbon attained within each capsule was calculated from the carbon content of a binary Fe-C alloy placed within the capsule, and from the activity coefficient of carbon in the Fe-C system as found by Smith for CO/CO2/C equilibrium. The activity of carbon in Fe-Ni-C austenite determined by this method at 1000°C agrees with prior work by Smith, who used mother method. The measurements are extended to 800°and 1200°C. The activity coefficient of carbon 7c, in Fe-Ni-C austenite is given by: where xC is the ratio of carbon to metal atoms and XNi is the ratio of nickel to metal atoms and where the standard state is chosen such that yC = 1 as xc approaches zero in Fe-C alloys. This equation appears to be valid for xni < 0.3, and 1073° < T<1473°K. ThE activity of carbon in Fe-C austenite has been measured by smithL at 800°, 1000°, and 1200°C. Smith has also studied the effect of nickel on the activity A. J, HECKLER and P. G. WINCHELL are Graduate Student and Associate Professor of Metallurgical Engineering, respectively, School of Metallurgical Engineering, Purdue University, Lafayette, Ind. This paper is based on a thesis submitted ty,to Purdue University, in partial fulfillment of the requirements for the degree of M.S. in Metallurgical Engineering which A. J. HECKLER received from Purdue in January 1962. Manuscript submitted August 13, 1962. IMD of carbon in austenite at 1000°C. In both these studies the activity of carbon was fixed by a flowing CO-C02* *Gas mixtures of hydrogen and methane were also used in Ref. 1 but these results are not incorporated in Ref. 2 or in the present study. gas mixture. In the present work, Smith&apos;s results for Fe-Ni-C austenite are confirmed and extended to 800" and 1200°C by a different experimental technique. EXPERIMENTAL PROCEDURE In essence the experimental technique consisted of enclosing specimens of various nickel contents in an initially evacuated silica capsule and annealing the capsule until carbon equilibrium was attained among the enclosed specimens. The carbon activity obtained within the capsule was determined from the final carbon content of the binary Fe-C alloy included in each capsule and the results of smith.&apos; In order to evaluate this method the absence of nickel transfer between specimens must be established and the attainment of carbon equilibrium between samples must be assured. The absence of nickel transfer was demonstrated in the case of an originally pure iron sample which was annealed at 1200°C in a capsule with a 27.3 at. pct Ni alloy. The final nickel content of the iron specimen was less than 0.1 at. pct, a change which has a negligible effect on carbon activity. The attainment of carbon equilibrium was demonstrated within every capsule and in over half the results by achieving the same final carbon content in a sample which carburized during equilibration and in a sample of the same nickel content which decarburized during equilibration. The base Fe-Ni alloys were vacuum melted from Ferrovac E or electrolytic iron and Mond or electrolytic nickel. The samples were rolled and/or swaged and their carbon content adjusted to the desired pre-equilibration level either by methane-hydrogen carburization or by direct carbon transfer from a graphite source in a sealed silica capsule. As mentioned previously, high-carbon and low-carbon samples were prepared for most nickel levels in each capsule. The specimens were cleaned and

Jan 1, 1963

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By Corliss R. Kinney

SINCE the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated pace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. POSSIBILITIES OF ACETYLENE One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and&apos; these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1946