Search Documents

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of September, 1913: Members. ANDERSON, ANDREW P., Min. Engr 908 Story Bldg., Los Angeles, Cal. ANDROS, STEPHEN 0., Min. Engr University of Illinois, Urbana, Ill. BECKETT, PERCY G., Min. Engr Globe, Ariz. BLAIR, THOMAS S., JR., Prest. Blair Engrg. Co 343 S. Dearborn St., Chicago, Ill. BOYLE, HARRY, Min. Engr S07 Lowman Bldg., Seattle, Wash. BRADEN, EUGENE B., Vice-Prest., Selby Smelting & Lead Co., Merchants Exchange Bldg., San Francisco, Cal. CHALMERS, JOHN W., Min. and Elec. Engr., Morro Velho, Villa Nova de Lima, Honorio Becalho Minas Geraes, Brazil, So. America.

Jan 10, 1913

Discussion of the paper of G. K. Burgess and J. J. Crowe, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2537 to 2591. HENRY M. Howe, New York, N. Y. :-I think we can hardly rate the importance of the entry of the Bureau of Standards into our field. There is no body in the world that is better fitted to undertake this work than that Bureau, and it is work which really calls for the aid of some national organization. The skill and care with which this work has been done speaks for itself. It is very striking that within a very few months the distinguished English investigator, Professor Carpenter, of whom I spoke before, thought that he had disproved the existence of beta iron by proving that the A2 retardation which Professor Burgess has now demonstrated did not occur. Dr. Burgess's demonstration of the existence of. this retardation makes the existence of beta iron very probable, in my opinion. Osmond used to call beta iron " decipuum." You knew of its existence as you know of the existence of certain planets, only by the perturbation which it caused. Certain phenomena could not be explained, except by assuming the existence of a third allotropic form, beta iron. The evidence that you got was always evasive and susceptible of other explanations, except that which we have to-day, which it seems to me is not capable of other explanation. Professor Carpenter proceeded in the same way that Dr. Burgess has, by taking the heating and cooling curves of exceedingly pure iron, and thought that he had shown that there was no thermal change, no absorption or evolution of heat at the supposed A2 point, and hence that the A2 point did not exist. This he did by a piece of reasoning which I think seems to most of us rather surprising. That is to say, if of ten witnesses, three have seen a thing and seven have not, the evidence of the seven who have not is set aside, and that of the three who have seen stands. In Dr. Carpenter's own experiments under certain conditions he found the A2 change, the heat evolution., under certain others he did not. That is like the three witnesses who saw and the seven who did not see. You can arrange your test so that this change will not become visible or so that it is masked. But though an existent change can be masked a non-existent one cannot be shown. So that the reasoning seemed to me wholly fallacious.

Jan 12, 1913

By F. H. Spedding

From thermal, metallographic, X-ray, dilatometric, and electrical resistance data a Phase diagram is proposed for the La-C system. TWO compounds are formed, body-centered-cubic Laz C, having a large range of solid solubility, and body -centered-tetrago-nal Lac2 . The former melts incongruently at 1415°C, and at 25OC it has an electrical resistivity about two and one-half times that of bure lanthanum. The latter melts congruently at 2356°C and at room temperature has an electrical resistivity about equal to that of bure lanthanum. The addition of carbon to La lowers the melting Point of La about 115' C, raises the higher (B-Y) transfomzation about 10" C and appears to have no effect on the lower ( a-0) transformation. The addition of carbon appears to lower the oxygen content in the metal and improve the machinability; however, the tendency to oxidize is increased. Two eutectics are formed in the system. The first occurs at 2.2 pct C and melts at 806" C, while the second occurs between Lac2 and C with a melting point of2271"C. PETTERSSON,~ in 1895, was the first to prepare lanthanum dicarbide by heating the oxide with carbon in an electric furnace. He showed that this yellow, crystalline but brittle carbide had a formula corresponding to LaCz and that it reacted with water with the evolution of hydrogen and hydrocarbons and the formation of the hydrated oxide. Von Stackelberg's investigation of the crystal structure of the MCz carbides showed that the lanthanum dicarbide is of the tetragonal calcium dicarbide-type structure. He found the lattice parameters were a = 3.92 and c = 6.56.* Bredig,' using X-ray methods, showed that the room-temperature form of lanthanum dicarbide is stable up to 1750 °C and that above this temperature it transformsoto a face-centered-cubic structure, a = 6.0 ± O.lA, probably of the pyrite, FeSzstruc- typ? The reported discovery of two new cerium carbides, suggested that a corresponding face-centered-cubic lanthanum monocarbide and a body-centered-cubic lanthanum sesquicarbide might exist. This paper describes work on the lanthanum-carbon system which is part of a study of the rare earth metals and their alloys now in progress in this laboratory. EXPERIMENTAL PROCEDURE Source of Materials—The lanthanum metal was prepared at the Ames Laboratory by metal1o;hermic reduction of the fluoride with calcium metal. The results of spectrographic and chemical analysis indicated the presence of 0.01 pct Y, Al, Cu, Fe, and Si; 0.02 pct Ca and Mg; 230 ppm C; and 115 ppm N. The carbon used was of two types: 1) "National Special Graphite Spectroscopic Electrodes," and

Jan 1, 1960

By G. K. Burgess

THE question of the allotropy of iron, in spite of a vast amount of experimental work and perhaps an even greater amount of theorizing, is not yet settled. That there is a definite transformation in iron near 900,° the A3 point, is generally recognized, as well as the fact that the temperature of this transformation is lowered by the addition of carbon and metallic elements. On heating, the transformation Ac3 is always found at a higher temperature than the transformation on cooling, Ar3. Whether the A3 transformation is sharp like the melting point of a pure substance, or extends over a considerable range of temperatures, embracing perhaps as a lower limit the A2 change, appears to be still an open question for pure iron. The nature and identity of the A2 transformation, it would appear from recent publications, has not yet been satisfactorily settled. In the present paper a critical, historical summary is given of the experimental investigations of the location of A2 and A.3 in pure iron, together with brief mention of some of the theoretical aspects of the subject, and an account is given of a series ?of experiments carried out with several samples of very pure iron which were studied by two methods of thermal analysis in the range from 5000 C. to 1,000° C., and which it is believed furnish a contribution of considerable interest as to the location and nature of the A3 and A2 transformations. Great attention has been given to the details of experimental manipulation and to the preparation of the samples, as it was soon found that some of the discrepancies noted in the work of many experimenters may be traced largely to lack of precautions which we have found essential. For example, to anticipate somewhat, it is necessary to provide a suitable practically gas-free furnace, the heating and cooling of which may be regulated to a nicety. To render a minimum the deforming effects on the cooling and heating curves of the poor conduction of the sample, it must be of a form and mass to pass on its heat rapidly and completely to the thermocouple; and finally the sample itself must be freed from gases which, if present, further mask the definiteness of the heating and cooling curves. We, have also varied within wide limits the several factors which may influence the determination of the exact location and shape of the transformation ranges, especially the mass and preparation of sample, rate of heating and cooling, design of furnace; and finally, as nearly as it is experimentally possible, we have worked with a substance approaching pure iron, free from occluded gases and other impurities, and contained within a vacuum.

Jan 10, 1913

By A. L. Mular

The flotability of crushed zinc oxide pellets which were doped to produce more n-type or less n-type (more p-type) properties was studied with a Halli-mond tube. Flotation data are presented to show that the pH at which 50% recovery occurs and the collector concentration for 50% recovery depends upon the concentration of doping agent added substitu-tionally for zinc in zinc oxide. The time of sintering of pellets has a slight effect on flotation behavior. A speculative model is proposed to explain the observed behavior in light of the fact that zinc oxide is a semiconductor and has a space charge region at the surface. Experimental verification is necessary before the proposed model can be established as correct. In recent years, the attachment of flotation reagents to minerals has been shown to depend upon the behavior of an electrical double layer which exists in the liquid near the mineral-liquid interface.' Thus, a mineral placed in water will undergo a surface re-arrangement, most likely be preferential dissociation of lattice atoms or by surface adsorp-tion-desorption reactions, to form a dissociation electrical double layer with the solution. Among the many factors which influence adsorption processes, the past history of the mineral itself is one of the most important. Because of trace impurities, minerals from different localities may exhibit marked differences in flotation behavior. This is not unexpected, since investigators who have studied the detailed structure of the double layer's3 have known for some time that the impurity content of many minerals may exert strong influence on double layer variables. For this reason, their studies were usually made with minerals of high purity. The precise relationship between impurities in a mineral and double layer parameters such as capacity and electrostatic potential has been obscure. However, impurities in a semiconductor type mineral which is in contact with a solution have been recently shown to produce changes in the properties of a space charge layer which extends into the bulk of the semiconductor to a distance of one micron or more.4 The double layer is influenced by the space charge layer, whose origin is best discussed in terms of the band theory of solids. A qualitative description of the behavior of impurities in the bulk of a semiconductor, from a chemical point of view, is useful at this point. Briefly, impurities or defects (lattice vacancies, interstitials, etc.) in semiconductors such as PbS, ZnS, FeS2, Cu2S, NiS, NiO, Fe2O3, ZnO, CdS, MnO2 and many others, behave somewhat like acids or bases in water. For example, water dissociates into hydrogen and hydroxyl ions according to

Jan 1, 1965

By Richard F. Link, George S. Koch

Advantages and disadvantages of deflecting (wedging) diamond-drill holes to obtain sampling data are compared with the alternative of drilling additional holes. The discussion is based on a statistical analysis of a large set of deflection data from exploratory boreholes in South African gold mines. Representative cost comparisons show the conditions under which deflections are likely to be desirable.

Jan 1, 1969

By Orlando Romig

PART I-PREPARATION OP METALLIC SINGLE CRYSTALS WITH ESPECIAL REFERENCE TO SINGLE CRYSTALS OP ZINC? As metals and alloys are composed, of, an aggregate of allotriomorphic crystals or grains, each possessing an individual orientation, the physical characteristics of a metal or an alloy are closely related to the properties of the individual crystals. The preparation and study of single metallic crystals are, therefore, matters of considerable importance. The advent of the X-ray spectrograph as a valuable metallurgical tool has magnified the importance of this subject, because the interpretation of some X-ray spectrographs is difficult unless single crystals are used in these studies. PREVIOUS WORK The first paper, as far as the writer knows, on the behavior or preparation of single crystals of metals is by Baker.1 He describes the behavior of extruded wires of sodium and potassium. These wires, when pulled in tension, instead of I showing the usual conical fracture common to most metals, had a chisel-shaped fracture when they were broken. I and II, Fig. 1, have a similar fracture. Baker checked his results by preparing single crystal wires from molten sodium and potassium and observing their properties. He prepared the wires by filling glass tubes, under oil, with the molten metal. The surfaces of the strained wires showed slip bands of remarkable clearness of which photographs are shown in his paper. He concluded that these wires were single crystals and "that the portions of the metal brought into play are cubes. Such cubes, when placed so that a plane through 'two opposite edges was parallel to the axis of the wire, would allow of lateral contraction by faces gliding over one another in one direction only and not in the direction at right angles."

Jan 1, 1927

By Donald A. Brobst

The minerals barite (BaSO4) and witherite (BaCO3) are the chief sources of the element barium and its compounds needed for many industrial processes and products. Barite, the principal ore mineral, is found the world over and is abundant and widely distributed throughout the United States.3 Witherite is much less common than barite, though more desirable in many ways as a raw material for the production of barium chemicals. England is the chief producer of witherite. Witherite is not mined in the United States at the present time, but it has been mined with barite from a deposit at El Portal, California. Barite is also called barytes, tiff, cawk, or heavy spar. Ordinarily it is a heavy mineral that crystallizes in the orthorhombic system. It is colorless, white, or gray, and transparent to opaque. In some deposits barite is black, yellow, brown, red, green, or blue because of included impurities. The streak is white and the luster vitreous to resinous or pearly. The specific gravity of pure barite (65.7 pct BaO and 34.3 pct SO3) is calculated to be 4.5, but inclusions and impurities in natural barite may reduce this value considerably. Well-formed crystals are generally tabular and have three cleavages. The barite of many deposits, however, has an uneven fracture and an apparent cleavage caused by separation along planes between successively deposited layers. The hardness is 2.5 to 3.5 on Mohs' scale. Commercially the terms "hard" and "soft" are used to refer to ease of grinding. Barite is relatively insoluble in water and acid, and thus can be used as a chemically inert material. Witherite, the natural carbonate of barium (77.7 pct BaO and 22.3 pct CO2), crystallizes in the orthorhombic system. The fracture is uneven and the luster is vitreous to resinous. The hardness is 3 to 3.5. The specific gravity of the pure mineral is calculated to be 4.29. It is transparent to opaque. The color is ordinarily white, gray, yellow, brown, or green. Geology and Distribution of Deposits Workable deposits of barite are widely distributed throughout the world in many geologic environments in sedimentary, igneous, and metamorphic rocks. Most deposits can be classified into three main types: (1) vein and cavityfilling deposits; (2) bedded deposits; and (3) residual deposits. 1. Vein and cavity-filling deposits are those in which barite and associated minerals occur along faults, gashes, joints, and bedding planes, and in breccia zones and solution channels. They also occur in various collapse and sink structures in limestone. Sharp contacts of the veins and cavity fillings with wall rocks are common. Barite cements fault and collapse breccia by replacement of the matrix or by filling voids. Large-scale replacement of the wall rocks beyond ore-controlling structures is rare. Barite in vein and cavity filling deposits is generally dense, "hard," and white to gray. Associated minerals are fluorite, calcite, ankerite, dolomite, quartz, and many sulfide minerals, especially pyrite, chalcopyrite, galena, and sphalerite. Gold, silver, and rare earth minerals occur with barite in some deposits in the western United States. Barite is also a gangue mineral in metallic ore deposits but production as a byproduct from such deposits will be affected by many economic factors. The host rocks are igneous, sedimentary, and metamorphic rocks of pre-Cambrian to

Jan 1, 1960

By George W. Neumann

The mines and concentrator of Brunswick Mining and Smelting Corporation are located in the northern part of the province of New Brunswick, approximately 20 miles distant from the City of Bathurst. Discovery of the No. 6 orebody by diamond drilling in 1952 was followed by the finding in March 1953, of the larger and higher- grade No. 12 orebody, approximately six miles to the north of the No. 6 deposit. Original development was financed by St. Joseph Lead Co., and included a small open-pit operation with a 10C ton per day pilot mill at No. 6 orebody, shaft sinking and underground development at No. 1; orebody, and an extensive program of laboratory and pilot plant metallurgical research on No. 12 ore. These operations were suspended in May 1958, and remained in standby condition until June 1961, when the equity of St. Joseph Lead Co. was purchased by a group headed by M. J. Boylen, K. C. Irving, Maritime Mining Corporation, and the Patino Corporation. Construction of a mine plant and concentrator at the No. 12 mine commenced in October 1962 and the concentrator was placed in operation in March, 1961b. Preparation of the open pit mine for production, construction of the No. 6 Concentrator to produce bulk Pb-Zn-Cu-Ag concentrate from No. 6 ore, and construction of an Imperial Smelting Process smelter at Belledune were started in 1964 and placed in operation in September 1966.

Jan 1, 1970

By R. E. H. Pomeroy

The statistical data given in this paper are taken from the actual performance of the No. 2 reverberatory furnace of the Nevada Consolidated Copper Co., Mc Gill, Nev., for a period of four months, from April to July, 1914. The principal furnace dimensions are: Length, 132 ft. % in. at the skim-line level; average width, 18 ft., 10 in. at the skim-line level. The roof is 7 ft. above the skim-line level at the firing end. The average area in the uptake flue is 36 sq. ft., and the area above the skim line under the vulcatory arch is 24.3 sq. ft. Fig. 1 shows a diagrammatic plan and sectional elevation of this furnace. The furnace is equipped with two 400-b.h.p. Stirling waste-heat boilers set in parallel. California crude petroleum is used for fuel and has a specific gravity of 16.5" B., flashing in open test at 199" F. The oil is heated to about 200" F. in a steam heater before going to the burners, requiring about 9 b.h.p. per furnace day to heat it from the line temperature to the burning temperature. Measurement is made by oil meter, checked daily by reservoir readings. The oil is fed by gravity (34 Ib. static pressure) to seven low-pressure blast burners of the Steptoe type (Fig. 2). The blast for these burners is supplied at about 40-08. pressure by a motor-driven Connersville blower of 42 cu. ft. capacity per revolution. The air supplied by the blower through the burners for atomizing the oil amounts to about 10 per cent. of the theoretical air necessary for complete combustion of the oil. The remainder of the necessary air enters the furnace through the burner openings in the firing wall. No checker holes are provided, and the charge holes in the roof are equipped with slide gates and " dog houses" to minimize air leakages. The combustion of the fuel, as shown by gas analysis at the front of the furnace, is practically complete, the carbon monoxide in the gases being less than 0.5 per cent. The draft at the firing end of the furnace is 0.18 in. of water. At the throat or in the uptake above the "verb" the draft is about 1 in.

Jan 1, 1915

By P. Greenfield, C. C. Smith, A. M. Taylor

The Mg-Zr alloy ZA and Mg-Mn alloy AM503(S) are shown to have a markedly improved resistance to creep deformation after suitable heat treatments. This improvement makes them suitable for certain stress-bearing fuel element components in nuclear reactors. The extent of strengthening is described and an explanation of the behavior of both materials is given, based on a combination of strain-aging and grain growth. The increase in operating temperatures of fuel element components in Calder Hall type nuclear reactors has necessitated the development of magnesium base alloys with a very high resistance to creep at temperatures up to 500°C. Such alloys are not required for fuel element cans, which require high-creep ductility rather than strength, but for can supporting and stabilizing components, which are needed to support the imposed loads without deforming more than about 1 pct in times of up to 40,000 hr. The amount and type of alloying addition made to magnesium for these parts is limited by the necessity of keeping the cross-section to thermal neutrons as low as possible. The alloys must also possess a high resistance to oxidation in CO2. Alloys which have been developed for this application include ZA, an alloy of magnesium with 0.5 to 0.7 pct Zr and AM503(S), an alloy of magnesium with 0.5 to 0.75 pct Mn. In the as-extruded condition these alloys are very weak and ductile in creep but it has been found that they can be strengthened to a significant extent by heat treatment. This paper describes the method of developing a high-creep resistance in ZA and AM503(S), the extent of the strengthening produced and discusses the probable mechanisms of strengthening. TEST MATERIALS Specimens were taken from typical casts of ZA and AM503(S) alloys extruded into 2 1/4-in.-diam bars, supplied by Magnesium Elektron Ltd. Typical analyses of the bars were as follows: The as-extruded mean grain diameter was 0.001 to 0.002 in. for the ZA alloy and 0.003 in. for the AM503(S) alloy. EXPERIMENTAL METHODS Extruded bars of ZA alloy, 2 1/4 in. in diameter and 9 in. long, were heat treated in electrical resistance furnaces in an atmosphere of flowing CO2 containing 50 to 300 ppm water, thereby reducing the extent of oxidation compared with that which would have occurred in air. Heat treatments were carried out at 600oc for times of 8, 24, 48, 72, and 96 hr and material was subsequently both furnace cooled and water quenched. In order to measure the effect of time of heat treatment, specimens were creep tested at 400°C and 336 psi for about 1000 hr. Subsequently, the behavior of material heat treated for 96 hr at 600°C and furnace cooled was tested at a variety of stresses from 200° to 500°C. Tests were also conducted at 200o and 400°C on material in the as-extruded condition for comparative purposes. With the AM503(S) alloy, only the effect of heat treatment at 565°C for 4 hr was examined. It has been shown1 that such a heat treatment produces marked strengthening in this alloy. Tests on this material were conducted at a variety of stresses at 200°, 300°, and 400oc with comparative tests on as-extruded material at 200o and 400°C. The creep tests were carried out on machines using dead-weight loading and direct micrometer strain measurements on specimens 5 in. long and 0.357 in. diameter. At temperatures of 400° C and below, the creep tests were conducted in air, but at higher temperatures an atmosphere of CO2 was used. Grain size measurements were made on ZA in the extruded and heat treated states and on each specimen after creep testing. This was done by a line count of a minimum of 20 grains in two or three random fields in the longitudinal and transverse directions. The same method was used for measuring the grain size of as-extruded AM503(S), but the grain size of the heat treated material was so large that this method could not be employed. For heat-treated AM503(S) the large grained characteristics (between 0.1 and 1 in.) were confirmed by the measurement of individual grains. In the case of the ZA alloy, specimens taken from various stages in the program were analysed for hydrogen by a combustion method. Material in various states was also analysed for the soluble and insoluble zirconium content by dissolving in dilute hydrochloric acid. This technique has been useda for the determination of amounts of zirconium present

Jan 1, 1962

By Larry G. Hayes

Development of the Bowers-Campbell zinc deposit, located in the Shenandoah Valley two miles northwest of Timberville, Va., was commenced in 1956 by the Tri-State Zinc Co. The occurrence of lead-zinc mineralization in this area has been known for many years, but the first serious exploration program was initiated in 1951 by the geologic staff of Tri-State Zinc Co. Ordovician dolomites. The deposit is approximately 700 ft long, 100 ft wide, and 475 ft thick. Its projected plan has an elongated ovoid shape, where- as the profile appears boot-shaped with the upper portion outcropping. Vertical cross sections show the lense as having been thrust-faulted along certain bedding planes. The movement along these bedding thrusts varies greatly and in one case, has offset the deposit so as to divide it into an upper and lower orebody. The breccia lense strikes parallel to the N 34" E strike of enclosing strata.

Jan 9, 1960

By Oliver Bowles

THE inorganic non-metallic minerals, that is, the non-metallics exclusive of coal, oil, gas and related minerals, constitute the basic raw materials for a number of essential industries. It is estimated that the value of the raw materials in this group produced in 1919, together with certain of the primary products ordinarily manufactured at the mine, exceeded $800,000,000. They are employed chiefly in the building, agricultural, and chemical industries. It has been estimated, by the Bureau of Mines, that approximately 00,000,000 worth of non-metallic minerals and their products were used in the building trades during 1918; with the great increase in building since that date and the increased cost of materials, the value of non-metals used in such industries during 1920 probably exceeded $500,000,000. The chief of these materials are cement, building stone, crushed stone, sand and gravel, clay products, lime, gypsum, glass materials, slate, talc and soapstone. In many of the producing industries of this great group, the waste is so great that the expense of handling it is an important item in the production cost. The utilization of waste is receiving unusual attention in many of the non-metallic industries at present. The most obvious advantages of such utilization are: (1) Conservation of mineral resources, (2) the removal of waste heaps that in many places obstruct development, (3) manufacture of new and useful products, (4) reduced production costs through elimination of a large part of the item of waste-disposal expense. In many industries there is keen competition between producers of various products used for the same purpose, so that advantage will accrue to the manufacturer who is able to reduce his production costs.

Jan 1, 1921

By W. E. Bruce, R. J. Morrell, James Paone

This chapter is a partial summary of an investigation by the U.S. Bureau of Mines (USBM) made in response to a recent request by the Assistant Secretary, Water and Power Development of the U.S. Department of the Interior, for a comprehensive review of horizontal boring technology related to underground power-line installation. This review is concerned primarily with 3 to 36-in. diam horizontal holes from several hundred to several thousand feet in length. An electric power system consists of three essential functions: generation, transmission, and distribution. The generation component includes the generating station and step-up substation; the transmission component includes the transmission line and stepdown substation at typical voltage levels ranging from 69 to 345 kv for underground lines and 69 to 500 kv for overhead transmission lines; the distribution component includes the distribution line carrying the commonly used voltages of 120, 208, and 240 v, the distribution transformer, and the line to the service customer.l The Federal Power Commission reports that 1600 miles of underground transmission lines of 60 to 345-kv capacity are now in service in the United States. By 1980, it is estimated that approximately 3000 miles of trans- mission lines will have to be placed underground.2 The cost of burying electric transmission lines underground in metropolitan areas, approximately 30 miles from the center of each of the most populated cities, will exceed $1.5 billion with the methods now available. The wide spread in unit costs of overhead and underground transmission lines narrows as right-of-way costs for overhead transmission in congested areas increase. Improved methods of underground emplacement will certainly reduce this difference in costs and even further favor underground emplacement. Also, in the future, overhead transmission lines will probably not be permitted in highly built-up areas.

Jan 1, 1970

By J. A. Bartnik, Gerald D. Rose, William H. Benson

New techniques in the magnetite and heavy media beneficiation industries demand more efficient magnetic dispersion and flocculation of the finely ground particles. Demagnetizing coils must produce several major effects, such as improving classification and screening efficiency, decreasing moisture content in filter cake and improving separation selectivity and green pellet properties. Likewise, magnetic flocculators must increase filtering rates and the settling rates of solids, improve magnetite recovery and produce cleaner water. To improve the design of equipment and to conduct tests leading to the optimization of such dispersion and flocculation, a program was initiated at Eriez Magnetics. The major conclusions reached are: 1. Laboratory and plant scale tests conducted on magnetite products show that a demagnetizing force of 450 rms oersteds at 60 cycles for 1/20- second duration will depolarize natural magnetite particles coarser than approximately 10 microns. This has been found satisfactory for most applications. 2. Effective flocculation of magnetite was obtained when a slurry with more than one percent magnetite was exposed for a period of approximately 1/15 second to a 600-gauss field. 3. The cost of demagnetizers (or flocculators) increases rapidly for larger diameter pipes. In order to reduce the cost, narrow rectangular sections are recommended for magnetic flocculators. 4. For minimum operating cost, permanent magnetic flocculators are ideal, chiefly because they do not require any maintenance and have no operating cost. 5. A newly designed electro-demagnetizing coil with high heat dissipation and a nonmetallic core provides high efficiency and long life. 6. To select the correct magnetic flocculator (or demagnetizing coil) the following information is necessary: a. Magnetic product susceptibility b. Magnetic product coercive force c. Percent of magnetic product d. Flow rate e. Viscosity f. Structure of magnetic product

Jan 8, 1968

NEW MEMBERS The following list comprises the names of those persons who became members during the period Mar. 10 to Apr. 10, 1914. Members ADAMS, DANIEL T., Mining 1416 Westminster Bldg., Chicago, Ill. BLICKENSDERFER, FRANK CLEVELAND, Sampler Morenci, Ariz. CAVERS, THOMAS WILLARD, Met Copperhill, Tenn. CLAPP, CHARLES H., Geol Univ. of Arizona, Tucson, Ariz. CLARK, PATRICK T., Pres Bullwhacker Mine, Spokane, Wash. COMSTOCK, HARRY, Mining Mineville, Essex Co., New York. COOKE, JOSEPH H., Gen. Mgr Mono Dev. Co., Gisborn, Tooele Co., Utah. COOPER, DEXTER P., Civ. and Hyd. Engr 101 Park Ave., New York, N. Y. DEGOLYER, E. L., Geol Apartado 269, Tampico, Mexico. DESHAYES, ERNEST F., Mine Foreman Baldy, N. M. DOUGLASS, WILLIAM CRAWFORD, Min. Engr 107 Leonard Hotel, Butte, Mont.

Jan 5, 1914

By Jacob T. Wainwright

This stove has been designed to meet the requirements of a fur nave that must be operated with either a reducing or a neutral flame ; and more particularly to make feasible the operating of re duction-furnaces with the cheaper grades of gas-fuel, which has heretofore been impracticable. In general, cheap gas-fuels result from incomplete combustion, and, being suited for further combustion, answer very well for heat ing purposes; and high temperatures may be attained with them, when they are used in conjunction with regenerative stoves. But, in operating a reduction-furnace, a high temperature is not the only requirement. It is also necessary that the fuel shall not be cansumed beyond a certain degree, in order to insure a re ducing flame for the reduction-process ; consequently, it becomes necessary to dispense with combustion as much as possible previous to the use of the fuel-gases in the reduction-furnace. Moreover, these gases must be preheated to a high degree, in order that a sufficient temperature may be maintained in the furnace; and, since this preheating cannot be accomplished by a previous, partial combustion of the gases themselves, it follows that the stoves for pre heating these gases should be heated to as high degree as it is pos sible to attain with an inferior fuel. This result can best be accom plished by complete combustion of the heating gases, and is further facilitated by preheating all of the air and gas used for this com plete combustion. It is more particularly desirable to preheat the air, since the combustible gases used may generally be obtained directly from the furnace, or gas-producer. The reducing gases, escaping from a gas-fuel reduction-furnace, are capable of considerable further dilution with air to secure com plete combustion, and consequently may be utilized for heating the stove to a high temperature, provided the air be sufficiently preheated.

Jan 1, 1889

By A. L. Field

A. W. FAHRENWALD, Socorro, 'N. M. (communication to the Secretary*).-When asked to discuss Mr. Feild's paper, I felt most highly complimented to have the privilege of commenting on such a worthy and needed piece of apparatus. In consideration of the importance of the viscosity of blast-furnace slags and the relation existing between the' melting point of a slag and its viscosity, the introduction of this apparatus should be a welcome means or assistant in the study of the physical properties of a slag. Up to the present time, it is A fact that this side of the practical working of the blast furnace has been sadly neglected by those investigating slags. It is easily seen that the fluidity of a slag is of as great importance as its melting point. It is not necessarily true that a slag having a low melting point will have a correspondingly low viscosity or be highly fluid. For example, a slag having a melting point of 1,100° C. may have to be superheated to, say,1,300° C., in order to have as high a fluidity as another slag whose melting point is, say, 1,250° C. The latter in this case would be the more economical. This point has been brought out very nicely by Mr. Feild. Before discussing this paper further, I think it will be well to outline some of the points, a discussion of which may be in order:

Jan 3, 1917

By John V. Beall, William F. Haddon

A long the mighty Andean Cordillera, there is splendor beyond imagination-in the natural beauty of the mountains and in daring engineering and lavish investment in the mines. This is the story of the great copper mines of Chile and Peru. Each mine has a special quality which has tested the physical and spiritual resources of the founder. In the early days of the older mines, the mining engineer of song and story was more the rule than the exception. He was physically tough, ingenious and a leader of men. In the current political and social environment of Chile and Peru, the foreign contract mining engineer is still needed; but he must be a different type of man. To John J. Selters at Cerro's Rio Blanco, the principal ingredient is still "toughness," but it is "toughness of mind" that is needed. "He probably should be a teacher." The copper mines are not new. They were, almost without exception, worked by Indians (La Exotica might prove the rule), and later by the intrepid Spaniards. Modern mining began after the turn of the century. In Chile, the first of the big ones was the Braden Copper Co. founded on the El Teniente deposit. This development was followed by Chile Exploration Co. at Chuquicamata and Andes Copper at Potrerillos. These properties have been developed over the years by vast expenditures of money and a monumental amount of labor. None was free of technical problems-metallurgy at Chuqui, marginal grade of the old mine at Andes, avalanches and the great fire at El Teniente. The evolution which has brought the established mines of Chile, and the new ones coming on stream, to their present state of development is in reality the work of wonders of input-money, engineering and responsible management in an atmosphere of political stability. Without any one of these, the result would have been failure.

Jan 11, 1969

INTRODUCTION The meaning of cash flow has already been defined as after-tax earnings available for use by the corporation or business. It is therefore apparent that a significant part of mineral economic evaluation is concerned with correct and accurate computation of taxable income under existing tax laws, and the proper treatment of tax allowances and deductions. The various methods of depreciation, depletion, and amortization are all means whereby the investor can earn back or recover, before taxes are imposed, the investments made for purposes of doing business or for the production of income. Each of these three types of tax deduction are applied to different investment items such as property, equipment, buildings, research, etc. The cost of buildings, equipment, machinery, and transportation equipment are representative of capitalized business costs that must be recovered by depreciation over the life of the asset. The property investment costs of acquiring natural resources such as minerals, oil and gas, and standing timber are examples of investment costs that may be recovered by depletion. Several other capitalized business costs, such as research expenses and trademark expenses, may be recovered by amortization. The term "capitalized" means that the in- vestment cost is not deducted as an operating expense in the year that it is incurred, but is spread out over a period of years through depreciation, depletion, or amortization deductions according to lawful schedules. Of course, any capitalized cost can only be deducted once. The other costs of doing business which are not capitalized, such as labor and operating costs, are said to be "expensed," i.e., they are written off for tax purposes in the year they occur. DEPRECIATION Depreciation, according to US tax law, is a deduction from taxable income permitted as a "reasonable allowance for the exhaustion, wear and tear of property out of its use or employment in a business." The original cost of the property is the usual basis for determining depreciation. Since depreciation write-off is applied over the useful life of the asset, the first step is to determine the estimated useful life or its allowable depreciable life. These two lives may or may not be the same. No average life is applicable to all types of depreciable assets under different conditions or in different types of business. It is the taxpayer's responsibility to determine the useful life of the asset according to his own operating conditions and experience, within the guidelines set by the US Internal Revenue Service (IRS). The Class Life Depreciation Range (ADR) System permits the taxpayer to choose from a range of depreciable lives at 20% below or above the present guideline life. The second step required in calculating depreciation is to determine an estimated salvage value for the asset. The salvage value is an estimate, made at the time of acquisition, of the amount of money which can be realized by the sale of the asset at the end of its useful life. The four depreciation methods most widely used in the US are: (1) the straight-line method, (2) the declining balance method (double declining balance), (3) sum of the years - digits method, and (4) units of production method. Straight-Line Depreciation Method The straight-line depreciation method is the simplest for calculating depreciation. The depreciation for each year is determined by subtracting the estimated salvage value from the first cost of the asset and dividing the result by the years of life. The method gives equal annual deduction over the depreciable life. Salvage value equal to or less than 10% of the first cost may be ignored. [first cost - salvage Straight line = years of life ] Declining Balance Depreciation Method Declining balance depreciation, or double declining balance (DDB) as most frequently applied, is used for accelerating depreciation in the early years of the asset and is the fastest depreciation method allowed by the US Internal Revenue Service. The declining balance

Jan 1, 1980