Search Documents

By L. T. Larson

The spectral reflectivity of zirconium in light of 441 to 668 nanometers (nm) wavelengths and air immersion has been determined. Bireflectance and apparent-angle -of-rotation measurements show zirconium to be optically isotropic when examined in light of approximately 484 nm wavelength. There is a direct relationship between bireflectance and the tilt of the basal pole of zirconium from the surface normal. This relationship allows the determination of the spatial orientation of the basal pole of an individual single crystal within a coarse-grained poly crystalline section to within± 2 to 3 deg for angles of basal pole tilt from 0 to 90 deg. In recent years considerable attention has been given to the quantitative determination of optical properties of opaque minerals by use of vertically incident, plane-polarized light. In particular, Cameron' and Cameron et a1.2 have developed criteria for the identification of a large number of anisotropic ore minerals based upon measurement of the apparent angle of rotation and the ellipticity or phase difference of the reflected light. It was shown by Larson and Pickle-simer3 that apparent-angle-of-rotation measurements may also be used to determine crystallographic orientations of grains of noncubic metals. In particular, it was shown that the basa.1 pole orientation in space of zirconium grains can be determined to ±3 deg for those grains with basal pole tilts of 10 to 90 deg from the plane of the section. Another, even more widely studied, optical property is reflectivity. cameron4 has commented upon measurement of the reflectance of plane-polarized, vertically incident light and Bowie and Taylor5 have made such measurements an integral part of their system of ore-mineral identification. Leow6 has reported on the spectral reflectivity of molybdenite and has used reflectivity values to calculate refractive indices and absorption coefficients. Cameron7 has made use of reflectivity values to ascertain aniso-tropic ore mineral symmetry and Piller and v. Gehlen8 have evaluated sources and importance of errors in reflectivity measurements as applied to calculation of optical constants. cambon9 has shown that reflectivity measurements using vertically incident, plane-polarized light are useful in the investigation of metals and in the identification of phases present in alloys. Bronson10 has made preliminary measurements on the optical anisotropy of beryIlium and Mott and Haines11 have published qualitative data on the intensity of light reflected from sections of bismuth, tin, and aluminum when these metals are microscopically examined under crossed polarizing plates. Koritnig12 has correlated the reflectivity of homogeneous solid solutions with their chemical compositions. From the above work and investigations in progress by this author, it is apparent that accurately determined values for the reflectance of vertically incident, plane-polarized monochromatic light from carefully polished surfaces of noncubic metals can prove useful in identification, composition determinations, and crystallographic orientation applications. Finally, reflectivity values, when measured in two media of differing refraction index and related to standards whose spectral reflectivities in these media are known, can be used to calculate optical constants such as refractive index and absorption coefficient. These constants may prove of use to those concerned with problems of electron band configuration. This paper reports the spectral reflectivity of zirconium measured in light of 441 to 668 nanometers (nm) wavelengths and air immersion. It also gives maximum bireflectance values for a prism section of zirconium in these wavelengths and shows how bire-flectance may be used to determine the crystallographic orientation of zirconium single crystals. Because of the lack of information on the reflectivities of the standards in oil immersion, no attempt is made to calculate the refractive indices or absorption coefficients although it is recognized that such values may be of fundamental importance. METHOD Single crystals of zirconium were cut by electro-discharge machining from a single-crystal rod grown from iodide bar by an electron-beam zone-melting process.13 The crystal sections were mounted in cold-setting epoxy resin and mechanically polished to a plane, uniform, bright surface. Each crystal was then chemically polished in a 26/26/43/5 mixture (by vol) of water, nitric, lactic, and hydrofluoric acids to remove the mechanically damaged and smeared surface layer. Final polish was obtained by electropolishing at 30 v in a bath of methyl alcohol and perchloric acid (98/2 by vol) at -70oc.14 Reflectivity measurements were made using a photometer system designed and developed at Oak Ridge National Laboratory and described in detail by Larson.15 Briefly, the reflectivity measuring system consists of a reflecting microscope; a double-beam, null-balancing photometer array; a mechanically driven microscope stage; and a direct X-Y readout of the reflectivity of the specimen relative to its orientation on the microscope stage. The measuring photometer receives its signal from the specimen through a slotted Wright occular placed on top of the photovisual head of the microscope. The reference photometer receives light through a flexible glass "light pipe" from a mirror in the reflecting system of the microscope. Monochromatic light is attained through use of interference filters (15-nm half-peak width pass bands) placed in front of a stabilized Vickers 12 v, 100 w, tungsten-filament, quartz-iodide lamp.

Jan 1, 1970

The new Ceramic Engineering Building of the University of Illinois is to be formally dedicated on Nov. 20 and 21. The occasion will be made one of great interest to the clay-workers of the country. It is expected that the exercises will be attended by many representatives of the architectural, structural, mining, geological, chemical, and manufacturing interests. In connection with the dedication exercises, an industrial conference will be -held, in which a number of topics of current interest to the ceramic engineer, the clay-worker and the manufacturer will be discussed by well-known experts. : The number of students registered in the College of Engineering of the University of Illinois eleven days after the beginning of registration - for the new year, is as follows: Architecture, 116; Architectural Engineering, 167; Ceramic Engineering, 46; Civil Engineering, 190; Electrical Engineering, 266; Mechanical Engineering, 273; Mining Engineering, 25; Municipal and Sanitary Engineering, 26; Railway Engineering, 34; total, 1,143. The enrollment of students in the whole University, not including the College of Medicine, the College of Dentistry and the School of Pharmacy, which are located in Chicago, is 5,21.4.

Jan 10, 1916

By A. C. Dorenfeld

In most mineral enterprises, what is the progress, and shift in responsibilities, as the young engineer advances in the corporation? You are all familiar with the normal pattern-in mine production from level boss, to shift boss, to superintendent to manager; in milling from test engineer, to shift boss, to foreman, to superintendent and then manager; in engineering from surveying on to Chief Engineer; and all then aspire to the corporation presidency. Note the shift-from purely technical jobs, say in the first five to ten years in the profession, to administrative positions for 30 to 40 years. What is the average preparation given to mineral engineering students, who can look forward to about 30 years of administrative work? From the catalogs of 21 institutions, offering 36 curricula of four years length, in mining and/or metallurgy, requiring the equivalent of about 150 to 160 semesterhours for graduation, the following results were obtained: Average number of semester hours of economics, 3 hr. Range of requirements, 0 to 8 hr. Thirteen curricula do not require any economics. Accounting and business law, average: 1 semester hr, 26 curricula do not require business law or accounting.

Jan 2, 1955

By R. W. Raymond

Edward Cooper was born in New York City, Oct. 26, 1824. His father, Peter Cooper, to say nothing of manifold reasoils for fame as an inventor and philanthropist, deserves to be remembered as a pioneer in the establishment .of public schools ; and it is not surprising that. he sent his son to one of the democratic institutions in which he was himself so ardently interested. From the public school Edward Cooper went to Columbia College, where he made the acquaintance of Abram S. Hewitt, who was first his tutor, afterwards his traveling companion, brother-in-law, business partner and life-long friend.' For twenty years I was the consulting engineer of the firm of Cooper & Hewitt, and also connected with the work of the Cooper Union, in which they were both deeply interested and faithfully active. On the basis of the intimate knowledge thus gained, I venture an estimate of Edward Cooper's character and career which, if not fully comprehensive, may facilitate a juster estimate than would be reached by the student of those data which the modesty of the man permitted to be placed upon public record.

Jan 1, 1907

By R. P. Smith

The diffusivity of carbon in iron, cobalt, and alloys of 89.7 and 79.3 wt pct Co has been determined by a decarburization method for the temperature range 850° to 1100°C. The Plots of log D us 1/T for the two Fe-Co alloys are linear through the region of the Curie temperature, showing that, unlike some cases of substitutional diffusion, carbon diffusion in these alloys is not affected by electron spin order. RECENT investigations1-' have shown that for substitutional diffusion in iron the change in diffusivity with temperature does not follow an Arrhenius equation, at temperatures near the Curie temperature. Data on the diffusivity of carbon in a iron5"9 indicate that this anomaly does not exist for interstitial diffusion; however, this has not been definitely established. Since cobalt and Fe-Co alloys, 80 to 100 pct Co, have Curie temperatures in a temperature range convenient for carbon-diffusion measurements they are suitable systems for studying the relation of interstitial diffusion and the Curie temperature. EXPERIMENTAL The carbon diffusivity, D, was determined by a decarburization method. The diffusion cylinders, made from small vacuum melts of electrolytic cobalt and plastiron, were about 0.76 cm diam and 6.3 cm long. A small amount of carbon was added to each melt to keep the oxygen content as low as possible. The cylinders were first treated with a hydrogen-3 pct water vapor mixture at 1100°C to constant weight, then carburized to the desired initial carbon content with a suitable CO-C02 gas mix-

Jan 1, 1964

By Roshan B. Bhappu

This is the Centennial year of AIME and many of us reading this issue of ' will be getting ready to attend the Centennial Celebration in New York from February 26 through March 4. The officers of the Division sincerely hope that a large number of our members will attend the fine technical sessions and social functions arranged for this really big meeting. The year 1971 will be a crucial one for MBD. This SME Division is a working group organized "to furnish a medium of cooperation among those interested in the basic unit processes and unit operations of minerals beneficiation; and to promote the advancement of this branch of mineral technology through meetings for professional intercourse, and to stimulate the preparation, reading discussion and circulation of papers connected therewith." No one can deny the worthiness of these objectives or minimize the efforts that Division officers and members have made to attain them. Much has been done over the past several years to achieve a smooth-running and effective MBD organization. However, there is still room for improvement and much more needs to be done in order to provide the best possible services for the membership and the profession.

Jan 1, 1971

By Robert S. Williams

On several occasions, when 60-40 brass is first obtained in the beta condition by quenching at about 825" C. and is then reheated, the writers have noticed that reerystallization will take place in the form of twin crystals at the grain boundaries of the original beta crystals. It was, therefore, thought that interesting results would be obtained if this twinning process was studied further, especially as to the temperature at which it first occurs. The material used in the investigation was a bar of extruded muntz metal, 1/2 in. in diameter, and of the following composition: Copper, 60.21 per cent.; zinc, 39.73 per cent.; lead, trace; iron, trace; tin, nil. Specimens 1 in. in length were sawed from this bar and a hole was drilled into the side of each specimen until it reached the center, and the tip of a platinum-platinum rhodium thermocouple was inserted. A small Hoskins' resistance-type electric furnace was used for heating the specimens. The specimens were first heated at 840' C. for 2 hr. and then quenched ' in cold water, in order to get the material entirely in the beta state. In every case, in the reheating process, the furnace was brought to the desired temperature before the specimen was introduced. The time occupied in preheating was from 20 to 30 min. By sawing back 1/4 in. on each side of the hole, two parts were obtained from each specimen and duplicate observations were possible. The specimens were held at the reheating temperatures for periods of 15 min., 30 min., 1, 2, and 4 hr. All specimens were etched with a freshly prepared mixture of equal volumes of concentrated NH4IOH and H2O2.

Jan 1, 1924

By E. V. Crane

A TREMENDOUS volume of the metal rolled annually into sheets, strips and coil stock finds its way to a host of stamping and manufacturing plants which are the quantity production units of the country. Considerable in volume, too, are the rolled and extruded rods which go into forging and manufacturing plants for conversion into the same general line: those widely sold metallic necessities and luxuries of the household, the office, transportation, farming and building construction. Yet, in spite of its age and its importance, the stamping trade has been doing its "engineering" largely by trial and error. Its distinctive method is shearing out and plastically working metal to finished shape in a few quick strokes with high loads and expensive tools which are warranted only by large quantities to be produced. The principal operations have many features in common with rolling and wire-drawing methods. Combinations of stresses are different, however, and details of operations are infinite in variety. An engineering study of the subject begins with stress analysis, but must go back to metallurgy for its foundation. A grouping of pressed-metal working operations according to whether the metal is (1) sheared, (2) bent, (3) drawn or (4) squeezed has proved useful. All of these groups include instances of both hot and cold operations. For discussions of metal working properties, the division between hot and cold working is taken as the recrystallization range of temperature. This, of course, brings tin, lead and often zinc into the hot-work range at or near room temperature. The outstanding hot-working press field is in forging: particularly of brass; all of which is included in the squeezing group.

Jan 1, 1931

By H. I. Aaronson, H. A. Domian, G. M. Pound

Zener's two-parameter theory of the y a reaction in Fe-X alloys is extended to encornpass austenite-stabilizing as well as fewite-stabilizing elements, and is then cottzbitzed with statistical thermodynamic theories of Fe-C alloys to permit development of a ther-modynamic description of the proeutectoid fewite reaction in Fe-C-X alloys. Equilibrium tielines are calculated for tile a + y rep'on from experimental data and frort extrapolations of the y/y +a equilibrium surface. Sectzovs of the y/y + 0 surface are calculaled for the tzetastable sstuation LYL u-kich alloyrtg eleitzents do not partition betzseen azrstenite andfer-rite. The finding that the metastable y/a + y curves Lie close to their equilibriuwz counterparts when X = Si, .Vo, Co, Al, and Cu but well below them when X = A/ln or Ari pr-elides a thermodunamic explanation for the expcri1?7e?ztally obserted absence of partition during the proeutec toid ferrite reartlon in the fortner alloys and for the occurrence of partition at hzgher ternperatures in the latter alloys. Cotarison ofno- patitzoa free-energy changes and y/y i a curr,es in Fe-C-X alloys with the equilibrium 11al1es of these quantities in Fe-C alloys furnishes additional qualitative insight into the irqluence of allojling elements upon the kinetics of the proeutectoicl ferrite reaction. THE introduction of a substitutional alloying element, X, appreciably complicates calculation of the thermodynamics of the formation of proeutectoid ferrite from austenite. As noted in the preceding paper,' the positional entropy of the interstitial species is the principal component of the free energy of an interstitial solid solution with which theory has so far been able to deal. One would expect, however, that other components of the free energy of this type of solid solution may be significantly altered by the addition of a substitutional alloying element. Even if the assumptions are made, by analogy to the case of Fe-C alloys,' that changes in the positional entropy of carbon represent a significant part of the thermodynamic effects of an alloying element, and that the remaining effects can be taken into account by fitting the equations developed on this basis to experimental data on Fe-C-X phase diagrams or on the activities of carbon in alloyed austenite and ferrite, the experimental information available on either of these quantities is not yet sufficiently accurate or extensive, respectively, to make such an approach useful. An attempt made by Zener on the former basis to explain the effects of alloying elements on the thermodynamics of Fe-C alloys in terms of a temperature-independent "free-energy change" (actually enthalpy hane') required to transfer 1 mole of an alloying element from austenite to ferrite, in which the "free-energy change" was determined by fitting the theoretical relationships developed to Fe-C-X phase diagrams, thus proved inadequate in part because of deficiencies in the available ternary-phase-diagram data.= Other difficulties of a more fundamental nature, however, also indicated the desirability of a different approach to the problem.3y4y6 zener6 subsequently proposed that the free-energy change associated with y — a transformation in pure iron can be decomposed into magnetic and nonmagnetic components. Alloying elements were assumed to affect those components separately. One parameter was used to describe the quantitative effect exerted on each component. These parameters were evaluated from Ms (martensite-start) temperature data and from other experimental information usually either readily available or measurable with acceptable accuracy. Zener applied this treatment only to the calculation of Fe-X phase diagrams in which X is a ferrite-stabilizing element. In the present study, this treatment is extended to include austenite-stabilizing elements, and then combined with treatments previously considered for Fe-C alloys1 to permit calculation of the thermodynamic quantities of interest in the austenite - proeutectoid ferrite transformation in Fe-C-X alloys, where a number of representative, and commonly used alloying elements are chosen for X, including Si, Mn, Co, Mo, Al, Cr, and Cu. The results are used to explain important features of the partition of alloying elements between austenite and proeutectoid ferrite, as reported in a companion paper7 on the basis of electron-probe analysis, and to provide some additional understanding of the influence of alloying elements upon the kinetics of nucleation and growth of proeutectoid ferrite. Portions of this treatment6 have been clarified in the course of a review by Kaufman and Cohen.3 The consolidated summary of these developments with which this section is begun provides a basis for further clarification of the treatment, from which extension to include austenite- as well as ferrite-stabilizing elements is a natural consequence. The division of the free-energy change associated with the 7 - a transformation in pure iron, into two independent components is formally stated as:

Jan 1, 1967

By W. C. Schroeder

During the post-war period, and particularly during the past few years, coal production has been maintained at a reasonably constant level. This is in contrast to the greatly expanded demand for oil and natural gas. Certain markets for coal, such as the railroad and for home heating, have tended to decrease, but this decline has been offset by an increase in demand for other uses, particularly for electric power. Since the United States has very large reserves of coal and relatively limited reserves of natural gas and oil, from the conservation viewpoint, it would be better if the increased demand were to fall more heavily on coal. Where coal has lost certain markets, the decision has not always been made on the basis of price, and, in fact, in many instances, the markets have been lost where coal could show a price advantage. There are various reasons for this situation but it can be attributed in the main to the preference of certain consumers for the convenience offered by liquid and gaseous fuels. In the production of chemicals such as benzene, phenol, or ammonia, coal still plays an important role. As co-products from coke-oven operations, a wide variety of aromatic chemicals are available. In recent years, however, the production has not been sufficient to supply the demand, and it is not profitable to build coke ovens to make chemicals unless there is a market for the coke as well. As a result, the petroleum industry is beginning to take a stronger part in the production of aromatic chemicals. Natural gas has almost displaced the coke-oven water-gas machine for the production of hydrogen for the synthesis of ammonia, as well as for the synthesis of methyl alcohol and other oxygenated compounds. This information is not new and is given here only as a basis for the discussion of the broad significance of the development of the gasification process. It is clear that if coal is to regain some of its old fuel markets, as well as to maintain a position in the field of chemical synthesis, processes must be available for converting coal to the type of fuel the customer wants, and for a cheap method of furnishing gaseous raw material to the chemical industry. The operation of coke ovens and water-gas machines is not the answer to this problem for at least two important reasons: (1) the limited supply and relatively high price of good coking coals, and (2) the relatively high costs of the combined operations of coking and manufacture of water gas.

Jan 1, 1953

By Charles Hart

THE-report of the advisory committee to the U. S. Bureau of Mines, on the use of oxygen in metallurgy, brings to the art of steelmaking a radical change in the method of operation of the many processes of this widely diversified industry. When completed, the improvements suggested by the use of oxygen will be far-reaching and revolutionary. As to its effect upon the iron blast furnace, the use of oxygen should be as important as any of the improvements in the art of iron smelting and should take its place beside the German "Hochofen" which was the first attempt to use a shaft for preheating the stock, and beside the hot-blast stove which heated the blast before entering the furnace. The former initially produced molten iron and the latter made unbelievable economies in fuel consumption. It would seem that a discussion of this paper would be best served by following the conclusions on page 17 of the report and analyzing them seriatim. 1. (a) A decrease in costs, due to higher smelting heats is only attainable by taking full advantage of these heat units. This is affected by, adding additional ore to the burden which in turn increases production and yields a larger tonnage upon which to figure costs. These economies appear in decreased cost per ton of iron for coke and limestone consumed, and a proportionate reduction in all items entering the cost above materials. We can take no exception to these. premises. It is a well-known fact that silicon in the iron and sulfur removed" are the result of hearth temperature, other matters remaining constant. To a practical furnaceman the most satisfactory manner of controlling a furnace is by increasing the burden. It is not necessary, therefore, to consider the question of refractories, for this discussion presupposes that the temperatures in the furnaces will be kept practically where they now stand for making the various grades of iron. The same situation obtains in regard to the height of the furnace, which, as intimated, was one of the great strides forward in this art, and its abandonment at this time, is inconceivable. The shaft prepares the stock so that at each succeeding step we have exactly the proper conditions. All the stock entering the furnace is dried and preheated. The limestone is calcined by sensible heat practically at no cost, for this is sensible heat which otherwise would pass from the top with the gases. Under normal conditions, external calcination has been attempted without tangible results. Under normal average furnace operation, limestone requires about 760 B.t.u. for calcination and the loss of sensible

Jan 11, 1924

By A. I. Krynitzky, Henry S. Rawdon

The most commonly used material for terminals in spark plugs is commercial nickel wire, because of its relatively high temperature of melting, excellent heat conductivity, and slow rate at which the metal is oxidized, even upon continued heating at high temperatures. The grade commonly used for this purpose averages 97 per cent. nickel, the remainder being manganese, cobalt, iron, copper, with traces of other impurities always found in commercial nickel. A peculiar and interesting type of deterioration that occurs in these nickel terminals during the service life of the spark plug was recently brought to the attention of the Bureau of Standards. Commercial spark plugs vary greatly in their size and shape and the terminals differ considerably as to their relative size, shape, number, and arrangement with respect to one another. Although this defect was studied in detail in only one form of spark plug, the deterioration is a characteristic of the material, i.e., of nickel wire, rather than of the particular type of spark plug in which it was noted and studied. The mechanical features of the plugs, however, have a considerable bearing on the time required for the deterioration to become serious. The results of this study of the deterioration of nickel terminals in service should be of value to the makers of all types of spark plugs in which the terminals are made of this metal. CharacteR of Deterioration of WIres During Service Macroscopic Appearance and Properties of Changed Wire.—The nickel terminals in which the deterioration was studied were taken from spark plugs having a central terminal with the ground or side terminals attached firmly at both ends to the shell of the plug. In some of the plugs, two side terminals were used, one on each side of the central one. Although both terminals were found to have deteriorated to some extent, the attack of the central one was quite negligible compared to that of the side ones. These latter wires had developed, in service, transverse cracks that, in many cases, were as sharp and definite as a knife-cut. After a separation occurred, the breach widened by loss of material from the

Jan 1, 1921

By F. Claisse, R. Angers

Self-diffusion in iron has been measured during rapid a-r transformations using a variant of the Kryukou and Zhukhovitskii diffusion method. The study was performed by thermally cycling iron foils (1 to 6 cpm) through the transformation (=910°C). Some foils have been subjected to over 1000 cycles and some have spent more than 15 pct of their total diffusion time in the process of transformation. The experimental results show that the a-r transformation has no measurable effect on self-diffusion in iron. The study is completed by a quantitative analysis of mechanisms which can affect the diffusion rate during the transformation. The analysis confirms the experimental results. SINCE diffusion is an important factor in many solid-state transformations, it is of interest to study how it is affected by the stresses generated during these transformations. Clinard and Sherby1'2 were the first to make a study along these lines. They measured diffusion coefficients in Fe-FeCoV couples subjected to slow thermal cycling (1.5 cph) through the a-r transformation range. They found an enhancement of diffusion by a factor of about two. The purpose of the present paper is to report measurements of the self-diffusion coefficient of iron during much more rapid thermal cyclings (1 to 6 cpm) through the a-r transformation (-910°C). These more rapid cyclings produce higher strain rates during the transformation and should emphasize any possible influence of transformation upon diffusion. EXPERIMENTAL Iron foils, 25 to 35 µ thick, were cold-rolled from 99.92 pct pure iron and annealed in pure helium for 2 hr at 870°C; the resulting grain diameter was about 150 µ. Specimens 0.5 by 8 cm were cut from the foils and I7e55 was vapor deposited on one of their surfaces. A 38 gage alumel-chrome1 thermocouple was spot welded in the middle of one of the specimen long edges, Fig. 1. Two 38 gage chrome1 wires were also spot welded along the same edge on each side of the thermocouple; they were placed 2.5 cm apart and used for electrical resistance measurements. In order to prevent twisting and crumpling, the specimens were pinched between two quartz plates 0.1 by 1 by 7 cm and the assembly was close fitted into a 1 cm ID quartz tube. Four holes were drilled through the tube to let the 38 gage wires out: these were connected to the recording equipment by means of extension wires. 20-gage nickel wires fixed at both ends of the specimens were used to thermally cycle the foils by Joule heating. The above described device was placed in a 2.7 cm ID quartz tube which in turn was placed in a tubular furnace. Either a pure helium atmosphere or circulating hydrogen was used during the experiments. Specimens were subjected to thermal cycles between a minimum temperature To and a maximum temperature Tm at rates ranging from 1 to 6 cpm. This was obtained by maintaining the furnace at a constant temperature near the minimum temperature To and periodically passing an electric current through the specimen. Cooling was achieved by heat losses to the surroundings. The forms and periods of cycles were varied from one specimen to another; however, each specimen was subjected to one type of cycle only. The temperature and electrical resistance variations of the specimens were recorded as a function of time. The temperature curves were used for diffusion calculations while the electrical resistance curves were used to monitor the transformation and to determine its starting point and its approximate duration. Diffusion was measured by the method developed by Kryukov and zhukhovitskii3 and modified by Angers and Claisse.4,5 In this method a metallic foil is coated on one side with a radioactive isotope and the activity is measured periodically on both sides during the diffusion anneal. The following equation then holds: where: I1 Activity on the surface on which the deposit is made. I, Activity on the opposite surface. t Diffusion time. B Constant. D Diffusion coefficient. d Foil thickness including the deposit. G(t) A function of time; it is a second order correction term which is given graphically in Refs. 4 and 5. The diffusion coefficient D is found by plotting ln[(Il - I2)/(I1 + I,)] -G(t) against t; the resulting slope m leads to an accurate calculation of D through Eq. [2]. The effect of the a-r transformation on diffusion is expressed by the ratio DT/DU where:

Jan 1, 1970

By F. V. Lene, E. J. Westerman

The recrystallization behaviors of two extruded and cold-drawn experimental sintered aluminum powder alloys, containing 1.75 and 3.0 pct Al2O3 by weight, were compared with that of extruded and cold-drawn commercially pure alumirzum. The kinetics of recrystallization of the alloys are described semiquantitatively. For the alloy containing 1.75 pct A l203 the rates of nucleation and of growth were also semiquantitatively determined. THE most striking property of aluminum alloys strengthened by a dispersion of Al2O3, the so-called SAP alloys, is their stability at elevated temperatures. One of the manifestations of this stability is their resistance to recrystallization after they have been cold worked. Most of the commercial grades of either the Swiss SAP or of Alcoa's Aluminum Powder Metallurgy Products have not been recrys-tallized after cold working, even when they are heated for a long time at a temperature near the aluminum melting point. Lenel, however, observed that the dispersion strengthened aluminum alloys with a larger spacing between the oxide particles than that of most commercial grades would recrys-tallize.1 It appeared to be of interest to further investigate the mode and kinetics of recrystallization of these alloys, and to compare their recrystallization behavior with that of commercially pure aluminum. Because homogeneous deformation of these SAP alloys in tension did not provide sufficient cold work to induce recrystallization, they were cold worked by wire drawing; the nonuniformity of this deformation unavoidably complicated the interpretation of the recrystallization studies. EXPERIMENTAL DETAILS Extrusions—Two types of sintered aluminum powder extrusions were used in this study. One type, designated AT-400, was produced from Reynolds atomized aluminum powder consisting of spherical particles averaging 3µ in diam and containing 1.75 wt pct of Al2O3. This powder was very similar to the R3M powder from which extrusions were previously prepared with an average spacing of 0.9µ between oxide particles.2 The second type, designated MD 2100, was produced from Metals Disintegrating Co. flake powder containing 3.0 wt pct of Al2O3, with an average flake thickness of 0.8µ. The average spacing between oxide platelets in MD 2100 extru- sions was 0.45µ.2 Powder compacts of 3/4-in. diam were extruded at 1000°F into 0.097-in. diam (AT-400) and 0.093-in. diam (MD 2100) wires by methods previously described.3 In order to compare the recrystallization behavior of sintered aluminum powder extrusions with that of wrought commercially pure aluminum 3/4 in. rod stock of 1100 F aluminum was extruded at 1000°F into 0.102-in. diam wire. Wire Drawing—Tungsten carbide dies were used for the AT-400 and 1100 F alloys. They had an included angle of about 15 deg and reduced the wire area approximately 7 pct per pass. Steel dies with an included angle of 11 to 13 deg and an average reduction per pass of 10 pct were used for drawing the MD 2100 alloy, because drawing this alloy through the carbide dies produced overdrawing defects. Heat Treatment—The cold-drawn wires were cut into small samples, and the deformed ends were etched off. The samples were each wrapped tightly in a single layer of aluminum foil, and individually isothermally annealed in a lead bath. Metallography—The modes and kinetics of recrystallization were determined by metallography. Mounted and polished specimens were anodized in a solution of 1.8 pct HBF4;4 examination under polarized light clearly revealed their grain structures. The recrystallized grains were generally much larger than those of the unrecrystallized matrix, and could clearly be distinguished because they alternated between maximum and minimum light reflection when the microscope stage was rotated, while the unrecrystallized matrix had a comparatively homogeneous "salt and pepper" structure. The fractional recrystallized volumes of the dispersion hardened alloy wires were determined by cutting and weighing of recrystallized and total transverse areas on photomicrographs. The recrystallized grains in the 1100 F alloy were too small to be cut out individually; therefore a combination of cutting and lineal analysis was used in this case. RESULTS AND DISCUSSION Modes of Recrystallization—The modes of recrystallization of the three alloys varied widely. In the 1100 F alloy nucleation and growth started in the region midway between the center and the surface;

Jan 1, 1961

By Arthur F. Taggart

The quality of aggregate materials is. of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 1, 1950

By Willard C. Lacy

Rather than attempting to present a summary of the many and highly varied papers that have been presented at this symposium on sampling and grade control, I will attempt to extract the general philosophy of analysis and approach, and attempt to identify the trend of future developments. First, the term "sampling" is used with its broadest connotations. A sample consists of a representative portion of a larger mass, and must represent the mass not only in the grade of contained metals or minerals, but also in all other respects in terms of mineralogy and mineral quality (1, 5), deleterious materials, recoverability of economic components, physical behavior, geophysical response (I), and even archaeological and environmental aspects (7, 11). The sample must be taken from a locality and in such a manner and quantity that it is representative of the larger rock mass. This calls for complete and accurate geological control and an understanding of the nature and distribution of the contained chemical and physical elements and a record of the effectiveness of the different sampling methods. Second, value of a given mass of ore material is based upon its profitability - the difference between recoverable value and costs to achieve recovery, beneficiation and sale. There is a strong movement in mining geology control toward more complete analysis in determining cutoff grades and in grade control, as illustrated by the kriging of metallurgical recovery factors as well as grade at the Mercur Mine (8). To achieve a "profit- ability factor" as a guide for economic mining practice requires further integration of: 1) the value of contained metal or mineral, 2) percentage recovery of values, 3) dilution of ore with waste rock, 4) addition to, or loss of value as a consequence of by-product materials or deleterious components, 5) cost of producing a saleable product plus mini- mum profit to justify the effort (cutoff), and 6) cost of land restoration (7, 11). All these parameters vary with the rock type, rock structure, mineralogy, depth, geometry, mining and metallurgical methods, but they must be sampled and analyzed if sampling and grade control are to reflect profitability. A wide variety of deposits has been presented at this symposium; each deposit with its own problems and special solutions. Deposits containing high unit-value components, e.g. precious metals and diamonds, present special problems in the obtaining of accurate samples and generally require statistical analysis control methods or may disregard or modify occasional high or occasional low values, based upon experience (12 ) Grade control may be accurate for the long term but may vary for the short term. Bulk sampling is always essential. Deposits containing metals or minerals with low unit value are very sensitive to transport costs, and they are often very sensitive to small amounts of deleterious components or differences in physical or chemical behavior. Problems of sampling and grade control change with the genetic type of deposit, with the stage of deposit development and with the size of the information base. Precious metal epithermal deposits (2, 6, 8), because of rapid vertical zonation and erratic lateral distribution of values, have always been difficult to evaluate and maintain grade control and ore reserves. On the other hand, evaluation and grade control are relatively easy in bulk-low- grade deposits (4, 13). However, these deposits generally have a low margin of profit and are sensitive to mining and beneficiaton costs, price fluctuations and political costs. Industrial mineral deposits (5) often must be evaluated on the basis of their behavior, rather than by chemical analysis. Environmental impact generally increases with the scale of the operation, but certain elements or minerals have especially high impact effects (7, 11). In the exploration phase there is no production control of sampling procedures and careful geological observations are particularly essential. The greatest number of problems is related to the oxidized outcrop where the chemical environment of the ore body has changed and the contained values may have been enriched, depleted or values left unchanged (2, 6). Present evidence suggests that gold values may be very mobile under certain conditions (2, 6) and stable under others. Everything must be sampled in detail. Principal values and by-product or deleterious elements may vary dependent upon their position within the soil profile. Such factors as geomorphic position, erosion rate, vegetation, climate, etc., may affect the interpretation (1, 3). During the development phase it is equally easy to overtest, to have "paralysis by analysis," as to undertest (3, 6). Bulk samplng and testing are

Jan 1, 1985

By Michael Chender

INTRODUCTION The project financing described elsewhere in this book is available to major mining companies on the basis of a strong balance sheet, a significant equity position in a project of proven feasibility, and a demonstrated ability to bring ore deposits into production. "Junior" mining companies, which are most active in Canada, Australia, the US, and South Africa, by definition do not meet these criteria. In many cases, junior companies will need to raise money simply to cover the costs of acquiring and exploring potential deposits. In what follows we will look primarily at junior financing practices in the US and Canada, although the same general principles will apply in Australia and South Africa. The principal vehicles for junior mine company financing are limited partnerships, the private placement of securities and debentures, and public offering of securities, and property deals with stronger companies, in the form of leases, earn-ins and co-ventures. The cost (in terms of dollars or equity) and, to some extent, the applicability of using these difficult approaches varies with the stage of development of the property and with the corresponding degree of risk to the investor. Much junior company fund raising is, in fact, "interim" financing in that it allows the company to improve its properties and develop its assets to the stage where more favorable financing arrangements may become available. Companies will therefore often use several of the approaches described above during the development life of a specific property. LIMITED PARTNERSHIPS Limited partnerships and syndications are a popular way of structuring the initial private financing of mine developments because of their attractive tax consequences for the well-to-do investor. Costs of exploration and development can in many countries be passed through as deductions to the limited partners, who are thus able to gamble on a possible windfall at little real cost. In addition to private Canadian funds, much German money flowed into Canadian exploration ventures on this basis, but stopped in 1982 due to economic conditions in West Germany. In the US, recent regulations have, in the great majority of cases, taken away the ability to "shelter" income in mining limited partnerships. Deductions taken by the individual investor cannot exceed the amount of money he actually has at risk. Nevertheless, the allowable deductions are still attractive and some of the major mining companies are now beginning to look at limited partnerships as a vehicle for attracting additional exploration funding. Ranchers Exploration and Development has successfully put together several drilling funds on this basis. THE PRIVATE PLACEMENT Initial funding for the acquisition and preliminary exploration of prospects is often accomplished through a private placement of unregistered securities or, where it is not a problem to carry debt on the statement, by a private placement sale of debentures. A fledgling company wishing to do a public offering may well be advised by an underwriter to accomplish a small private placement as a precondition of the larger offering. In this way, the sale of the registered securities is not inhibited by the company starting out with a debt-ridden balance sheet and no demonstrated ability to secure the additional financing generally necessary beyond the proceeds of that offering. In the US, the securities offered in a private placement are not registered with the Securities and Exchange Commission (S.E.C.) but are restricted as to their resale, and could be further restricted by a underwriting agreement

Jan 1, 1985

By P. M. Kelly

TWO analytical methods for calculating the positions of matrix and twin reflections on electron-diffraction patterns of a twinned cubic crystal have recently been published.1,2 Meieran and Richman1 considered the case of twinning on (1 12) in a bcc structure, while a more general treatment, capable of analyzing twinning on any plane in a cubic crystal, was developed by Johari and Thomas.2 The latter authors applied their general rotation matrix to both (111) twinning in face-centered crystals and {112} twinning in body-centered crystals and they derived separate expressions for these two cases. This separate treatment masks the fact that in a holosymmetric cubic crystal a (111) twin is crys-tallographically equivalent to a {112} twin.3 This is analogous to the crystallographic equivalence of rotation and reflection twins in centrosymmetric crys tals. A particularly simple example of this equivalence occurs when the two twin planes are perpendicular to each other—for example (111) and (112). Then, if twinning on (111) moves a point P to a new position P1, and twinning on (112) moves P to P2, P1 and P2 will be related to each other by a 180-deg rotation about [110]— the direction normal to both (111) and (112). Since there are diad axis axis along (110) direction in a holosymmetric cubic crys tal the two positions P1 and P2 must be crystallo-graphically equivalent. In other words if a particular pole (hk l) is in a position P1 after twinning on (Ill), then after twinning on (112) a pole of the type {hkl}—but not the particular pole (hk1)—will also be in the position P1. As a result, when only the general (as opposed to the particular) indices of poles after twinning are required, twinning on (111) gives the same results as twinning on (112). To convert the results for a (111) twin to those applicable to a (112) twin, when the particular (as opposed to the general) indices of poles after twinning are required, all that is necessary is to multiply the indices of the twin poles by the matrix for 180-deg rotation about [lie], i.e., The analytical methods suffer the disadvantage that a new set of calculations must be performed for each different diffraction pattern or, as is done in the Meieran and Richman treatment,1 a lengthy list of the location of the twin spots in reciprocal space must be prepared. All the tedious computation involved in these analytical approaches can be avoided by simply plotting, on tracing paper, a stereographic projection of a crystal twinned on say (112). By superimposing this twin stereogram on a standard (001) projection (preferably with the points and indices in a different color from those on the twin stereogram) the relative positions of both matrix and twin reflections can be determined by inspection. Alternatively, a composite projection can be

Jan 1, 1965

By N. A. Gokcen, J. Chipman

A revised treatment of the authors' published data eliminates the complex relation previously proposed between concentration of silicon and activity coefficient of oxygen in liquid iron. Revised values of the thermodynamic properties of the liquid solution are presented. IN a recent experimental study of the reaction SiO2 (s) = Si+ 2O; Kf, = [% Si] [% O]² [1] the authors' found a substantially constant equilibrium product in liquid iron at 1600°C of 2.8x10-5 They also reported extensive data on the reactions: SiO2 (s) + 2H2 (8) = Si- + 2H2O (g); K'2= [% Si] (H2O/H2 [2] and H, (g) + 0 = H2O (g); K'3 =( H2 O [31 (H2) [%O] From the results on reaction 3 and earlier data of Dastur² on this same reaction in the absence of silicon, they determined the activity coefficient of oxygen, f0, on the basis of the definition K3 = (H2O)/ (H2)f0 [% 0] where K, is the equilibrium constant and f0, is taken as unity in the pure Fe-0 system. Similarly values of fsi were deduced from results on reaction 2. In a more recent study" of analogous reactions in the system Fe-A1-0, it was found impossible to reconcile the results on reaction 3 with Dastur's data; accordingly the latter were ignored and the equilibrium results were extrapolated to find a value of K, at zero concentration of aluminum. This procedure failed to locate the cause of the discrepancy but it did yield reasonable values of activity coefficients. It also avoided introduction of the complex empirical relation between the oxygen activity coefficient and the concentration of the added element. The same type of discrepancy exists for system Fe-Si-0.' In the earlier paper an attempt was made to fit both sets of data by a single curved line (Fig. 6 of ref. l), the form of which is contrary to the theoretical requirement of a finite slope at infinite dilution. In the light of experience on the Fe-A1-0 system the discrepancy must be recognized as one which can be resolved only by more refined measurements. Accordingly Figs. 6 and 10 are retracted. It is pointed out also that until the discrepancy is resolved Figs. 7, 8, and 11 are subject to some uncertainty. Qualitatively the following conclusions still appear valid: 1—The activity coefficient of oxygen is reduced by addition of silicon. 2—In dilute solutions the activity coefficient of silicon increases with its concentration. 3—With respect to equilibrium in reaction 1, the above effects are approximately compensating. The discussion of K'1 in the previous paper requires no revision. It was pointed out that the constancy of the product [% Si] [% 0]² ndicated a compensating effect of the activity coefficients of silicon and oxygen. Therefore, as a very good approximation, K1 = K'1 and the following average values are suggested both for K, and K', at the temperatures 1550°, 1600°, and 1650", respectively, 1.0x10-", 2.8~10-" and 5.5 ~lo-'. Revision of the thermodynamic treatment is necessitated by the recent appearance of new data, based on a combination of combustion and solution calorimetry,' which yields for the heat of formation of low-cristobalite from the elements, the value —209,330 ±250 cal per mol at 25°C. This is about 4000 cal larger than the value previously accepted. The new value for cristobalite is used, together with Kelley's tables of high-temperature heat contents" and entropies and with Korber and Oelsen's' heat of fusion of silicon to obtain the following equation for the standard free energy of cristobalite in the temperature range 1700" to 2000°K: Si (1) + 02 (g) = Si02 (crist.); ?F° = -217,700 + 47.OT [4] The free energy of solution of 0, in liquid iron is:8 O2 (g) = 20 (in Fe); AF° = -55,860 - 1.14T [5] and these two equations are combined to give: Si (1) + 20 = SiO, (crist.); AF° = -161,840 + 48.14T [6] ?F°1873 = -71,700 cal. From the experimental value of K, = 2.8x10-5, Si + 20 = SiO2 (crist.); ?F°1873 = -39,000 cal. [7] The combination of Eqs. 6 and 7 yields the free energy change when liquid silicon dissolves in iron to form the dilute solution of unit activity (1 pct). Si (1) = Si; ?F°1873 = -32,700 cal. [8] The heat effect in this process according to Korber and Oelsen' is an evolution of 28,500 cal per gram

Jan 1, 1954

By C. E. Lesher

Low-TEMPERATURE carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus 3/8 -in- or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal, of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic con-sumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold.

Jan 1, 1940