Search Documents

By S. Fugleberg

As a result of research work done during the planning of the Kokkola zinc plant it was found that a very efficient cementation of impurities from the suspension obtained after leaching copper and cadmium cakes was achieved by adding zinc dust to the batch without filtration after the leaching. All elements nobler than cadmium are precipitated with the exception of lead, which must be removed in a separate step. Using pure zinc dust, free from noble metals, the cadmium sponge produced will only contain elements that can be re- moved from cadmium by meltrefining. The process is thus : 1. Leaching and purification 2. Removal of lead (with BaCO3) 3. Precipitation of cadmium sponge with pure zinc dust 4. Meltrefining of briquetted sponge with NaOH for removal of Zn (and others) The paper deals with the removal of the most critical elements, i.e. Co, Ni, As, Sb, Cu, Pb, T1 in the liquid phase and Zn and T1 in the melt. A survey is also given of the behaviour of most of the other elements normally found in Cd raw material, such as Ge, Te, Se, Sn, In, Ga. It is shown that in most cases the benefit of an electrolysis in Cd production is very limited. In Kokkola 99.998% Cd is achieved by this method, but in favourable cases it may be possible to come quite close to five nines.

Jan 1, 1973

The total crude production from the Dutch East Indies, and the British Protectorates of Sarawak and Brunei for 1932 is given in the following table: Production, which had shown a rapid increase from 1921 to 1929, has since been reduced. Exploitation drilling in the majority of the larger fields was suspended and existing production kept within predetermined limits by beaning. Most of the smaller fields were shut down entirely. The depth of producing levels varies widely in the different fields. Shallow fields with drilling depths to 500 meters (1650 ft.) are still numerous as well as those with depths between 500 and 1000 m. (3300 ft.). A few of the newer fields reach greater drilling depths up to 1600 m. (5250 ft.). The deepest exploration well drilled to date (Djambi field, South Sumatra) reached a, depth of 2332 m. (7650 ft.) before abandonment in March, 1930. The specific gravities of the various crude oils produced range between 0.65 (86.2° A.P.I.) and 0.95 (17.5° A.P.I.). The lighter crudes have a high gasoline content and fuel oils are derived from the heavier crudes, which usually are rich in paraffin. Producing companies are: De Bataafsche Petroleum Maatschappij (Royal Dutch-Shell combine in Dutch territory); The Anglo-Saxon Petroleum Co. Ltd. (Royal Dutch-Shell combine in British territory); De Nederlandsch-Indische Aardolie Maatschappij (De Bataafsche Petroleum Maatschappij-Dutch East Indian Government combine); De Nederlandsche Koloniale Petroleum Maatschappij (Standard Oil Co. of

Jan 1, 1933

Roof Bolts An expansion shell and plug Westinghouse roof bolting assembly made for use with threaded steel rods and large flat washers or steel channel employs a plug larger in diameter than those for trolley wire service. The notched plug helps prevent shell and plug from turning. The unit is shipped complete. Circle No. 1 Fan The Jeffrey Mfg. Co. Aerodyne Midget fan is a self contained blower or exhauster for auxiliary ventilation through tubing. Operating rating with 5 hp motor is 6.5 in. maximum static pressure, and 6200 cfm free delivery volume. Weight is 340 to 475 lb and it may be furnished in open or permissible form. Circle No. 2 Heavy-Density Initial installation in the Mesabi Range country of the Wilmot-Daniels heavy-density concentrating system was a 175 ton per hour plant at the [ ] Skubic Bros. Virginia, Minn., operation. This Wilmot Engineering Co. unit has a separatory vessel providing unidirectional medium flow and as the only moving part uses a standard drag-line conveyor for lifting sink out of the bath. Circle No. 3 Portable pH Meter A low priced battery-operated portable pH meter of utmost simplicity announced by the Photovolt Corp. uses only 3 ordinary radio batteries which give over 2000 hours of service. Accuracy of 0.03 pH is claimed by the manufacturer for the model 125, and AC power line supply is available. Circle No. 4

Jan 1, 1952

By P. R. Swann, R. M. Fisher, W. R. Duff

Observations by transmission electron microscoPy of the microstructures in quenched Fe-A1 alloys provide the basis for revision of the Fe-A1 phase diagram. The diagram is characterized by first-order transitions between the disordered ferromagnetic a! solid solution and the two ordered phases FeAl and Fe3Al. However, second-order transitions showing corre-luted fluctuations in the degree of order near the critical temperature occur between the paramagnetic a! and FeAl and the FeAl and FeAl phases. ELUCIDATION of the true nature of the Fe-A1 equilibrium diagram has proven to be an extremely challenging problem as evidenced by the fact that six quite different versions of the iron-rich portions have been published since 1958.&apos;-6 The most recent diagram shown in Fig. 1 was proposed by Rimlinger6 based on X-ray diffraction analysis and dilatometry. He shows the single-phase fields of the ordered phases of the types FeAl(L20) and Fe3A1(D03) and the disordered bcc Fe-A1 solid solution, a, separated from one another in every case by large two-phase regions. Thus, he implies that in Fe-A1 alloys ordering always occurs via a classical phase transition. In contrast to this view, theoretical studies3&apos;" have concluded that the transitions a — FeAl and FeAl — Fe3A1 should be second- or higher-order in character. A further revision of the Fe-A1 diagram of state is presented in Fig. 2 based on our previous8,9 and current observations by transmission electron microscopy of the microstructures found in quenched specimens. The average quenching rate was 50,000°C per sec and although this was sufficiently rapid to prevent Fe3A1-type ordering below -550°C it was not sufficient to suppress ordering of the type FeAl in the temperature range -650" to 800°C. However, ordering during the quench is easily recognized since the FeAl phase formed during holding at temperature rapidly develops large antiphase domains whereas FeAl formed during quenching has a very fine domain size, -50Å diam. Each symbol in Fig. 2 indicates the result of a micro-structural examination of specimens heat-treated (-1 hr) until equilibrium was established. The results will be discussed in the order of the points, A - Dl marked on both diagrams with reference to the phase fields, critical temperature, and "transition" ranges, respectively. The dark-field micrograph corresponding to point A is shown in Fig. 3 and was obtained using a 111 reflection of the Fe3A1 structure which reveals both a&apos;/4<111> and a&apos;/2<100> antiphase domain boundaries.10 The structure observed in this specimen is typical of single-phase Fe3A1 and shows no evidence for FeAl or any other additional phase. The dark-field micrograph shown in Fig. 4 corresponds to point B on the two diagrams. It was taken with a 100 FeAl reflection which reveals a/2(111) domains and exhibits the typical structure of single-

Jan 1, 1970

By Wilbur C. Helt, Joseph J. Yancik

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production ; and to produce electricity. Because it is our nation&apos;s most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health and environmental goals are rapidly emerging. These technologies will allow coal&apos;s use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals. MARKETS FOR COAL: PAST AND FUTURE A simplified diagram of the marketing network for coal is shown in Fig. 1. As shown in this figure, coal is transported to its traditional

Jan 1, 1981

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a very general loosely used term that includes virtually all finely divided types of limestone as well as burned forms of lime. However, actually (and according to Webster) lime is only calcined limestone (known as quicklime, calcium oxide, or calcia). It also embraces the secondary product of quicklime-namely hydrated lime or slaked lime (calcium hydroxide). Fundamentally there are two basic types of limestone-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts in terminology. The only difference is that the dolomitic types are a combination of the elements, calcium and magnesium, whereas high calcium limes contain only 0.5 to 2 pct of magnesium. Both types, which are made through calcination at high temperatures, are shown chemically as follows: [ ] In the above reactions either type of limestone is burned (calcined) in furnaces known as lime kilns so that the carbon dioxide content of the stone is expelled as a gas. With high calcium limestone 44 pct of the weight of the stone is lost; with dolomitic limestone the loss is 48 pct. Also, both reactions are chemically reversible since quicklime absorbs carbon dioxide readily and in so doing transforms itself back to the original carbonate form. Most quicklimes correspond in size to the original rock, which varies from one to eight inches, depending upon the type of kiln employed. Slight shrinkage occurs during calcination. A few limestones when calcined will decrepitate (break down) into a fine powdery form; however, chemically it is the same as the pebble or lump-sized material. For some uses the lumps of quicklime are pulverized and packaged. Since quicklime has great affinity for moisture and carbon dioxide, it is perishable. When it absorbs moisture and CO2 slowly from the atmosphere, the resulting product is "airslaked." Consequently, it must be stored in dry, moisture-proof areas that are free from CO2. Because of its fugitive nature, it is usually consumed within a few weeks after manufacture. A more stable form of lime is hydrated lime-commercially made by adding water to the quicklime until the lumps break down into a fine, white powder. This product, which is usually packaged, can be stored more safely; and many of its uses are interchangeable with quicklime. The irreversible chemical reactions of hydrated lime for both high calcium and dolomitic types are: [ ]

Jan 1, 1960

By Charles E. Wait

The old laboratory at the School of Mines was among the notoriously bad ones, being situated in apartments of the main collegebuildings not originally intended, and conspicuously unfit, for the use to which they were put; while, as in many of our schools and colleges, the assaying was done in the basement of the college. Prominent among the disadvantages of such an arrangement are insufficient light, poor ventilation, and little or no provision to carry off offensive gases. It is not my intention now to present a complete description of this building. I wish merely to call attention to a few points in its construction and equipment, which may prove of interest to those who contemplate erecting buildings for snch work, and who may be, as we were in this instance, limited as to funds. In this laboratory every room is well lighted; all rooms used by students are well ventilated, and are provided with closed hoods for

Jan 1, 1887

By R. Schuhmann

Distribution of material in the fine sizes of a comminution product generally is well represented by the empirical equation&apos; y = 100 (x/k)a [1] in which y — cumulative percent finer, x = particle size, a -= distribution modulus, and k = size modulus. Charles3 found that the energy consumption in comminution is usefully expressed by another empirical relation, E = Ak(1-D) [2] in which E = energy input per unit volume of material, A = a constant, k = size modulus based on Eq. 1, and n = a constant; (1-n) is the slope of a plot of log E vs log k. Holmes3 has presented energy equations similar to Eq. 2. The constants a and n in Eqs. 1 and 2 have been shown to depend both on the nature of the material and on the comminuting device. Moreover, Charles showed that within experimental error a and n are a — n+1 = 0 [3] Combining Eqs. 2 and 3, E = A k-a [4] In the first sections of this article it is shown that the energy equation, Eq. 4, can be derived directly from the size distribution equation for the fine sizes, Eq. 1. The derivations are made without assuming any of the specific relationships between energy and particle size which have been common in previous literature. For comminution processes in which Eqs. 1 and 4 adequately represent the experimental data, the constant A in Eq. 4 is found to be a simple and useful inverse measure of grindability. That is, A is the energy consumption per unit volume of comminution product finer than unit size as determined from the straight line portion of the log-log plot of the size distribution. These considerations all lead to a unifying hypothesis of comminution mechanism from which both Eq. 1 and Eq. 4 can be derived. Finally, it is pointed out that this hypothesis raises serious questions as to the significance of the Rittinger hypothesis, the Kick hypothesis, and other theories in which energy numbers are systematically assigned to various size fractions of comminution products in order to calculate theoretical energy consumptions. Derivation of the Energy Equation from the Size Distribution Equation: For simplicity, consider the comminution of 100 volumes of a feed material of relatively uniform particle size. The comminution process may be considered as the summation of many individual and independent comminution events. The extent of comminution is most easily expressed as the number of comminution events, z. In the first derivation, the key assumption is that the characteristics of the comminution events in a given crushing or grinding process are substantially constant and do not vary with the progress of the comminution process. Accordingly the characteristics of an average comminution event may be defined. In one such event, a quantity of energy $E is applied to a single particle of size f and volume $v. The crushing of this particle produces fine particles with a size distribution similar to that given by Eq. 1: yw=100(x/ka)a0 [51 In this equation yo, a0, and k0 are used to characterize the product of an individual comminution event rather than the product of the comminution process as a whole. In using Eq. 5, we will not be concerned with values of x close to the feed size f and will therefore assume only that the equation is applicable to the finest sizes of the material. In 100 volumes of total product, the actual volume of product finer than x from a single comminution event, or dy, is given by The total volume of material below size x, resulting from z events, is then given by y = z(dy) =z(dv) (x/ka)a0 =" Eq. 7 reduces to Eq. 1 when we let a, = a and [8a] z =100/dv (ka/k )1 or k = ka (zdv/100)-1/a [8b] Eq. 8a shows that the distribution modulus of the comminution product is the same as for the product of an individual comminution event. Eq. 8b shows how the size modulus of the comminution product k varies with the extent of comminution as measured by the number of events, z, or as measured by the fraction of the feed actually subjected to com- minution1 zdv/100. The energy input to 100 volumes of total feed, or 100E, is the sum of the energy inputs for all the comminution events: 100E =z (dE) [9]

Jan 1, 1961

By Edwin R. Phelps

In the year 1900 about 212 million tons of bituminous coal were produced in the United States. Almost none of this was produced by surface mines (Fig. 1), because there was no large equipment suitable for stripping overburden at that time. By 1915 the surface mines had built up their capability largely through use of the steam shovel to the point that they produced 2.8 million tons of the nation&apos;s total production of 443 million tons. Over the intervening years between 1915 and 1970 surface mining provided a continually increasing percentage of the nation&apos;s bituminous coal, stimulated by the growing availability of giant surface mining machines, some of which are presently capable of removing 220 cu yd of earth with one bite of their mighty buckets. In 1970 the nation&apos;s surface mines produced 244 million tons of bituminous coal, over 40% of the total national production. On the other hand, the nation&apos;s underground mines hit a peak of 560 million tons in 1920, dropped to a low of 273 million tons in 1961, and are presently on a very slow rise. Environmental pressures generally oppose surface mining, and have forced coal companies to consider more underground mining in future planning. Also, since strippable reserves are decreasing in the eastern states, an increase in underground mining is expected over the coming years. However, in the western states there are enormous reserves to be extracted by surface methods. Why has surface mining increased, while underground mining has decreased? It&apos;s largely a matter of economics. The cost per ton is greatly reduced by surface mining because of the relative ease of obtaining the coal. Also, there is a much greater percentage of coal recovery-nearly 85% in surface mines within the minable area, as compared to an average of about 50% in underground mines. Much surface mining recovers coal that could not be extracted by underground methods because of coal bed thinness, or multiple beds close together, split seams, the nature of the roof, and other geologic conditions. What are some of the limitations of surface mining? First of all, with presently available machinery it is difficult to surface mine at depths

Jan 1, 1973

By Parke A. Dickey, R. Fettke

Drilling activity during 1944 increased considerably in the oil fields and slightly in the shallow gas fields of western Pennsylvania. The number of deep tests (middle Devonian or deeper) completed during 1944 was the same as in 1943 and did not result in discoveries of additional reserves of natural gas or oil. Thus far no commercial oil production has been obtained from sands below the Upper Devonian in Pennsylvania. As a result of the lack of new discoveries, oil production in nearly all of the producing areas in the entire Pennsylvania grade region declined 10 to 11 per cent. Stocks of Pennsylvania Oil The Peilnsylvania grade crude-oil stocks in storage on January 1943 were 2,479,000 bbl. In January 1944 crude stocks totaled 1,846,000 bbl., and during 1944 the stocks of Pennsylvania grade crude declined to a year-ending balance of 1,617,000 bbl. Nearly all of this oil is "unavailable for use," representing pipe-line fill, tank bottoms and limited working inventories at the refineries. The storage of Pennsylvania oil has declined to a point where little or no available crude oil is currently in storage. Prices The posted price of Pennsylvania oil remained constant during 1944; however, on Rug. I, 1944, the wartime Government subsidy was instituted at a rate of 75¢ per barrel. The average price in the Bradford area, including the subsidy, was $3.31 per barrel. New Technical Developments The Pennsylvania Grade Crude Oil Association started a rather ambitious program of research in production fundamentals and technology during 1944. Several well-qualified engineers have been employed and a laboratory is to be equipped at Bradford. The group will investigate, in cooperation with the American Petroleum Institute, the possibilities of bacteria as agents in oil recovery, and undertake other studies of both a fundamental and an applied nature. In cooperation with the Pennsylvania State College, the Research Group worked out a method of measuring water-intake rates in different strata. The method involves injecting salt water down a string of tubing and fresh water down the annulus, determining the location of the interface electrically, and measuring the input rates above and below the interface. The United States Bureau of Mines, in cooperation with oil companies of the Venango district, developed a simple gas-lift tubing string, which is operating successfully in some 20 wells. This device uses the air-gas mixture produced with the oil to lift it by the usual gas-lift principles. The Northern Ordnance Co. is experimenting with a chamber lift device that expels the oil in an unbroken column. These devices hold considerable promise

Jan 1, 1945

No records have been found of coal in the old Spanish documents, although some mention of it probably exists in manuscripts. Coal was found in Mt. Diablo, in Contra Costa County, about five miles south of the San Joaquin River in 1852, but the first mine, the Teutonia, was located in 1858. The deposits are located on both sides of a high ridge, and vessels of 1,000 tons burden could ascend the river to the nearest point to the mines.1 In 1854, coal was found about four miles from Oroville, on the Feather River, in Butte County. Development work was started and in 1856 a mine was opened. From the description the coal was likely a variety of lignite and probably never amounted to anything commercially, as it does not appear again in the records 2 The more valuable mines at Mt. Diablo were opened in 1859 and 1860. By 1867 there had been 11 mines started and at that time five were in operation. The seam conditions were much disturbed and lack of knowledge of them caused much waste of effort and money. All of the coal excepting that used locally and in nearby towns, was shipped to San Francisco, and largely used for steam purposes. The first receipts were in 1861-6,620 tons. A railroad to the river had been constructed and opened in February 1866. The Corral Hollow field in Alameda County was found and prospected to a small extent in 1862. Two mines were opened but little work was done and the field was then abandoned. Good exposures were rare and the cost of underground exploration was then prohibitive. The Commercial mine produced coal in 1869 and 1870, but a fire in the latter year destroyed the tipple and communications to the mine. The Livermore mine was abandoned after 18 months operation in 1875 and 1876 and no other work was done here until the nineties. In 1867 Hyne reported the presence of coal in workable thickness, and of good quality, on the property of the Pacific Coast Petroleum Company,

Jan 1, 1942

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922

By W. M. Clark

OUR interest in the matter of pyrometers and pyrometry is primarily that of a user of considerable quantities of heat-measuring equipment; and while we play be somewhat critical on the subject we have aimed to make the nature of these comments constructive. The glass industry in America dates back to 1609, when Capt. John Smith started a small glass plant near Jamestown, Va., with a few Italian workmen, to manufacture glass beads for trading with the Indians. While the industry has expanded until it has reached a volume of over $200,000,000 per annum, the means of heat determination in Colonial days was the human eye, and in much of the industry the same means is used today. About 15 yr. ago the largest glass-house supply dealers began to sell platinum pyrometers, but as nearly all of these proved un-satisfactory, pyrometers met a temporary rebuff from the old-time glass manufacturers. As their ruggedness of construction, reliability, and stability have been improved, however, pyrometers have gradually won their way into more and more extensive use throughout the glass trade. But there are still many applications where pyrometers are not used, largely because of cost and upkeep considerations. There are two distinct fields in glass works for pyrometry. The first calls for accurate temperature measurement and the second only demands knowledge of relative comparative fluctuations of temperature, to know whether the work is becoming hotter or colder. For example, in a lehr for annealing glassware and removing strain we want accurate temperatures to know that the ware is heated to the critical temperature for rapid removal of strain. On the other hand, in a glass pot furnace nearly 120 ft. (36 m.) in circumference, where the pyrometer couples only project inside the furnace wall for less than 2 in. (50 mm.), it is inconceivable that these few inches represent the accurate temperature at every point of the 120-ft. circumference but the relative readings as to whether the pyrometer shows schedule temperature fluctuations are valuable indications for control. The glass melting in the pots is,

Jan 8, 1919

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922

HUDSON MAXIM, Brooklyn, N. Y.-Immediately after the creation of the Naval Consulting Board, Admiral Strauss, Chief of the Bureau of Ordnance of the Navy, told members of the Board that the most important problem for the scientists to solve was erosion in large guns. The Navy, for years, had been working on the problem with marked suceess, but there was much yet remaining to be accomplished. As Chairman of the Committee on Ordnance and Explosives of the Naval Consulting Board, I communicated with several experts in the manufacture of steel, principal among whom was Prof. Howe. He generously agreed to help in every way possible, and the work that he has done and the time that he has spent upon it can he appreciated only by reading his paper. Prof. Howe asked for some rings. from a, certain 14-in. gun which Admiral Strauss had mentioned in particular, and in which, he had informed us, at each shot the bore of the gun, was enlarged about 0.001 in.,&apos; and that after a relatively small number of rounds it was considerably eroded. It has puzzled scientists for a long time to account for the peculiar erosive effect produced by the powder gases in a gun, arid: what Prof. Howe has done in his paper is worthy of Sherlock Holmes. He is a veritable Sherlock Holmes of science.

Jan 4, 1918

By C. G. Dunn

WITH respect to theories of recrystallization in metals plastically deformed, it has been said that the present status of this subject is far from satisfactory.1 It may also be said that before any mechanism of recrystallization for metals and alloys can be set forth in a satisfactory manner, there must be made available considerable data on orientation changes that occur during the deformation and recrystallization processes. Although extensive data have been published on recrystallization in single crystals and in polycrystalline specimens, more results of a type that can be classified according to simple orientation changes would be desirable in this complex field. It might even be said that before classifications are made according to types of orientation changes, it may be possible to classify a considerable amount of data into certain kinds of orientation states if groups of common or nearly common orientation occur. Methods for computing the probability of occurrence for various types of groups have been published2 and it has been pointed out in particular that it should be possible to analyze orientation data for high-order twin relationships between old and new grains even when agreement is not at all exact. In this connection, work on recrystallization in silicon ferrite reported in a paper concerned with complex groups of annealing twins&apos; indicated that some data were consistent with primary nucleation occurring according to a second-order or a third-order twin transformation. However, further work in this latter direction was definitely needed. It is, therefore, the purpose of the present paper to report data and analyses for primary nucleation in silicon ferrite following small deformations that have been carried out at the Pittsfield Works&apos; Laboratory of the General Electric Co. Analyses have been made with the aid of standard groups of twins that are reported elsewhere .4 PREPARATION OF SPECIMENS AND EXPERIMENTAL PROCEDURE The material used in the present investigation was taken&apos; from the same heat of steel as that used in a prior report.3 The finished strip in both cases was made by the Allegheny-Ludlum Steel Corporation according to methods that produce a high degree of preferred crystal orientation. Samples with large grains had the following composition: 3.45 per cent Si, 0.003 C, 0.008 P, 0.020 S, 0.075 Mn, 0.031 Al and 0.072 Cu. Thickness of specimens was 0.012 inches. Plastic deformation was produced by cold-rolling the samples on a mill with

Jan 1, 1945

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By J. H. Henderson, J. Naar

The displacement of a wetting fluid from a porous medium by a non-wetting fluid (drainage) is now reasonably well understood. A complete explanation has yet to be found for the analogous case of a wetting fluid being spontaneously imbibed and the non-wetting phase displaced (imbibition). During the displacement of oil or gas by water in a water-wet sand, the porous medium ordinarily imbibes water. The amount of oil recovered, the cost of recovery and the production history seem then to be controlled mainly by pore geometry. The influence of pore geometry is reflected in drainage and imbibition capillary-pressure curves and relative permeability curves. Relative permeability curves for a particular consolidated sand show that at any given saturation the permeability to oil during imbibition is smaller than during drainage. &apos; Low imbibition permeabilities suggest that the non-wetting phase, oil or gas, is gradually trapped by the advancing water. This paper describes a mathematical image (model) of consolidated porous rock based on the concept of the trapping of the non-wetting phase during the imbibition process. The following items have been derived from the model. 1. A direct relation between the relative permeability characteristics during imbibition and those observed during drainage. 2. A theoretical limit for the fractional amount of oil or gas recoverable by imbibition. 3. An expression for the resistivity index which can be used in connection with the formula for wetting-phase relative permeability to check the consistency of the model. 4. The Iimits of flow performance for a given rock dictated by complete wetting by either oil or water. 5. The factors controlling oil recovery by imbibition in the presence of free gas. The complexity of a porous medium is such that drastic simplifications must be introduced to obtain a model amenable to mathematical treatment. Many parameters have been introduced by others in Iprogressing" from the parallel-capillary model to the randomly interconnected capillary models independently proposed by Wyllie and Gardner3 and Marshall4. To these a further complication must be added since an imbibition model must trap part of the non-wetting phase during imbibition of the wetting phase. Like so many of the previously introduced complications, this fluid-block was introduced to make the model performance fit the observed imbibition flow behavior. THE IMBIBITION MODEL ASSUMPTIONS The following assumptions are common to many two-phase models previously described. 1. The wetting characteristics of the medium are clearly defined. 2. When two fluids co-exist in the medium, the wetting phase will fill the smaller pores and the non-wetting fluid the bigger ones. 3. The pores have a circular cross section. 4. Apparent pore radii are related to the capillary pressure (drainage) by

By E. H. Crabtree

THE heavy-media separation plant at the Central mill of the Eagle-Picher Mining and Smelting Co., near Picher, Okla., was started in February 1939. Since that time twenty-four million tons of lead-zinc ore has been treated in the mill, of which approximately 70 pct has been treated by heavy-media separation. Until January 1945, galena concentrate from the flotation plant was used as the sink-float medium. At that time minus 100-mesh ferrosilicon was substituted for the galena, and its use has been continued. The purpose of this paper is to compare the operating results and the costs of operation of the two media. For the purpose of this comparison the period Jan. 1, 1943, to Jan. 29, 1945, has been taken to represent the operation using galena medium; the period Jan. 29, 1945, to Sept. 1, 1946, to represent the ferrosilicon medium. During the first of &apos;these periods about seven and one-half million tons was milled; during the latter, or ferrosilicon period, more than five million tons was milled. It is believed that these tonnages are large enough to give representative data. FLOWSHEET The Central mill has a capacity of 15,000 tons per day. Briefly, the treatment used consists of crushing the ore through 11/2-in. and wet-screening out the minus 3/16in. portion. The minus 1 1/2 plus 3/16in. washed product is treated by the heavy medium; the minus 3/16-in. product is deslimed and jigged. The heavy-media cone tailing is discarded and the cone .concentrate is recrushed and jigged for the production of a coarse lead concentrate. The cone concentrate, impoverished of lead, is then ground in ball mills and treated by differential flotation. The minus 3/16-in. jig product is similarly treated. HEAVY-MEDIA PLANT The heavy-media cone plant treating the minus 1 ½ plus 3/16-in. product consists of one open-top cone 20 ft in diameter by 20 ft deep, equipped with a central airlift. Concentrate is discharged from the top of the airlift to a 3 by 14-ft low-head Allis-Chalmers drainage screen. Medium drains back into the cone, from the first half of this screen. The last half of the screen is provided with washing sprays for further removal of medium. Cone tailing is similarly drained and washed. Undersize from the washing screen is thickened and then cleaned in the medium-cleaning plant. When galena was used as a medium, cleaning was done in Fagergren and Denver flotation machines. The ferrosilicon is cleaned in three 36-in. and one 24-in. Crockett magnetic separators. A flowsheet of the cone plant is shown in Fig 1.

Jan 1, 1947