Search Documents

By Charles Legrand

(San Francisco Meeting, September, 1915) THE problem of mine pumping is so much affected by local conditions, and those conditions are so liable to changes during the life of a mine, that the best system to use is difficult to determine. The experience of the;, writer has been that, in general, for copper mines, electric pumping is most satisfactory unless the quantity of water to be pumped is great or. the mine does not use electric power for any other purpose. As a rule, however, figuring on the cost of necessary power plant, the total cost of: installation is greater with electric pumps than steam- pumps. As the water is liable to be gritty, outside-packed plunger pumps are to be recommended, and if the water is not acid, or only slightly so, chilled cast-iron plungers pay for their extra cost very quickly in diminished cost of packing. With chilled plungers it is possible to use metallic, packing instead of soft packing, if the water, is not too gritty nor the lift too high. In vertical pumps this packing is satisfactory for lifts up to 400 ft., in the experience of the writer; and may be found satisfactory for higher lifts. For water slightly acid, cement-lined pump bodies have given good satisfaction. For acid. water, both plungers and pump bodies should be made of acid-resisting bronze. For high lifts, especially with gritty water, a satisfactory pump valve is difficult to find. To reduce the unbalanced pressure on the valve at time of opening it is advisable to have narrow seats; this, however, brings high pressure on the seats when the valve is closed. On large valves for lifts of 600 to 1,000 ft. we have used leather, hard rubber, vulcanized fiber, and soft brass; for clear water the latter has given best satisfaction. The difficulties due to grit make it advisable to have large sumps where water can settle, and if possible, to have two of them so that they can be cleaned alternately. At the mines of the Old. Dominion Copper Mining ,& Smelting Co.; Globe, it was found that a small air. ejector discharging into a mine car is a very convenient way to clean mud and sand from a sump. .

Jan 9, 1915

By L. E. Shiffman

This paper describes the operation of two kerosine flotation plants in Alabama for cleaning —10 mesh bituminous coal. One plant treats washer sludge, the other raw coal. Data on capacity efficiency and capital and operating costs is given. Methods for increasing cell capacity are discussed. IN cleaning coal it has long been recognized that methods which give excellent results for the coarser sizes may give poor or even no cleaning for the finer sizes. Effective cleaning of the fines, therefore, is usually a separate and distinct problem. For many years the problem of fines was considered of relatively minor importance. Now there is growing interest in methods of cleaning the fine sizes of coal because: 1. There are more fines. Increasing mechanization and the adoption of full seam mining methods have resulted in the production of a greater percentage of smaller particles than were produced by hand loading methods. 2. The fines have deteriorated in quality. The same causes that have led to increased quantity have also operated to decrease quality through greater contamination with slate, rock, and other diluents. 3. The fines have become more valuable. When coal was comparatively cheap, loss of the finer sizes was tolerated but, with the rapid increase in the cost of mining coal, it has become imperative that the maximum amount of clean coal be recovered from the mixture of coal and rock delivered to the tipple. 4. In many cases, the fines have become a stream pollution problem. Increasing governmental activity and legislation to prevent stream pollution often have made it necessary to retain the fine material which formerly was permitted to escape with the washer effluent into flowing streams. The Sloss-Sheffield Steel and Iron Co. operates four coal mines, all within a 20-mile radius of Birmingham, Ala., with a total annual production of 1,-250,000 tons of washed coal. Three of these mines are in the Mary Lee seam and one in the Jefferson seam. Although some steam and domestic coals are produced, the major portion of the coal is used to make coke for blast furnace operation. Fine coal is desirable for coking, and all the coal so used by Sloss is crushed to 1/4 in. Therefore, there is no problem of an outlet for even the finest sizes of coal. Since the coal is used for metallurgical purposes, low ash is of greater importance than would be the case if it were used for steam generation or domestic heating. Based on present blast furnace practice at Sloss, it is calculated that each percentage of ash in the coal carries a penalty of $0.22 per ton of coal. Thus there is a considerable margin for operating costs in a fine coal cleaning method that will result in materially lowering the ash content of the cleaned coal. Development of Fine Coal Cleaning Problem In 1942 Sloss reopened its Bessie mine and constructed at this location a new preparation plant to clean 11/4 in. x 0 coal from the Mary Lee seam.

Jan 1, 1951

By L. E. Shiffman

This paper describes the operation of two kerosine flotation plants in Alabama for cleaning —10 mesh bituminous coal. One plant treats washer sludge, the other raw coal. Data on capacity efficiency and capital and operating costs is given. Methods for increasing cell capacity are discussed. IN cleaning coal it has long been recognized that methods which give excellent results for the coarser sizes may give poor or even no cleaning for the finer sizes. Effective cleaning of the fines, therefore, is usually a separate and distinct problem. For many years the problem of fines was considered of relatively minor importance. Now there is growing interest in methods of cleaning the fine sizes of coal because: 1. There are more fines. Increasing mechanization and the adoption of full seam mining methods have resulted in the production of a greater percentage of smaller particles than were produced by hand loading methods. 2. The fines have deteriorated in quality. The same causes that have led to increased quantity have also operated to decrease quality through greater contamination with slate, rock, and other diluents. 3. The fines have become more valuable. When coal was comparatively cheap, loss of the finer sizes was tolerated but, with the rapid increase in the cost of mining coal, it has become imperative that the maximum amount of clean coal be recovered from the mixture of coal and rock delivered to the tipple. 4. In many cases, the fines have become a stream pollution problem. Increasing governmental activity and legislation to prevent stream pollution often have made it necessary to retain the fine material which formerly was permitted to escape with the washer effluent into flowing streams. The Sloss-Sheffield Steel and Iron Co. operates four coal mines, all within a 20-mile radius of Birmingham, Ala., with a total annual production of 1,-250,000 tons of washed coal. Three of these mines are in the Mary Lee seam and one in the Jefferson seam. Although some steam and domestic coals are produced, the major portion of the coal is used to make coke for blast furnace operation. Fine coal is desirable for coking, and all the coal so used by Sloss is crushed to 1/4 in. Therefore, there is no problem of an outlet for even the finest sizes of coal. Since the coal is used for metallurgical purposes, low ash is of greater importance than would be the case if it were used for steam generation or domestic heating. Based on present blast furnace practice at Sloss, it is calculated that each percentage of ash in the coal carries a penalty of $0.22 per ton of coal. Thus there is a considerable margin for operating costs in a fine coal cleaning method that will result in materially lowering the ash content of the cleaned coal. Development of Fine Coal Cleaning Problem In 1942 Sloss reopened its Bessie mine and constructed at this location a new preparation plant to clean 11/4 in. x 0 coal from the Mary Lee seam.

Jan 1, 1951

By E. F. Loiseau

(Read at the Philadelphia Meeting, February, 1878.) UNTIL June, 1868, it had not been attempted, either in this country or abroad, to manufacture by mechanical means, from anthracite coal-dust, artificial fuel for domestic use. Several attempts had been made to utilize coal-waste by converting it into a fuel for manufacturing purposes, but none of the processes were original, and they were merely applications of the well-known European processes and machinery, slightly modified by American ingenuity and mechanical skill. With one exception all those attempts have been failures. The great difficulty in the application of European processes and machinery has always been the limited production, and the excessive cost of the manufactured product, as compared with the cost of mining and preparing the ordinary anthracite coal for the market. The only serious and intelligent attempt to manufacture, on a large scale, artificial fuel for manufacturing purposes, has been made by the Anthracite Fuel Company, whose works are erected at Fort Ewen, near Rondout, New York. This company, organized under the auspices of the Delaware and Hudson Canal Company, had to go through the usual course of difficulties, breakages, and disappointments, which seems to be the lot of every new industry. Thanks, however, to the energy and perseverance of Mr. L. L. Crounsse, a gentleman of means, from Washington, D. C., the enterprise succeeded, and it is to-day established on a permanent basis. In order to increase the production, and to reduce its cost, the Anthracite Fuel Company was compelled to change most of its plant, and to erect more powerful machinery, producing lumps of a larger size, almost twice the size of the lumps made previously by the same company. This increase in the size of the lumps has been resorted to in Europe as well as in this country, in order to increase

Jan 1, 1878

By E. F. Loiseau

Until June, 1868, it had not been attempted, either in this country or abroad, to manufacture by mechanical means, from anthracite coal-dust, artificial fuel for domestic use. Several attempts had been made to utilize coal-waste by converting it into a fuel for manufacturing purposes, but none of the processes were original, and they were merely applications of the well-known European processes and machinery, slightly modified by American ingenuity and mechanical skill. With one exception all those attempts have been failures. The great difficulty in the application of European processes and machinery has always been the limited production, and the excessive cost of the manufactured product, as compared with the cost of mining and preparing the ordinary anthracite coal for the market. The only serious and intelligent attempt to manufacture, on a large scale, artificial fuel for manufacturing purposes, has been made by the Anthracite Fuel Company, whose works are erected at Fort Ewen, near Rondout, New York. This company, organized under the auspices of the Delaware and Hudson Canal Company, had to go through the usual course of difficulties, breakages, and disappointments, which seems to be the lot of every new industry. Thanks, however, to the energy and perseverance of Mr. L. L. Crounsse, a gentleman of means, from Washington, D. C, the enterprise succeeded, and it is to-day established on a permanent basis. In order to increase the production, and to reduce its cost, the Anthracite Fuel Company was compelled to change most of its •plant, and to erect more powerful machinery, producing lumps of a larger size, almost twice the size of the lumps made previously by the same company. This increase in the size of the lumps has been resorted to in Europe as well as in this country, in order to increase

Jan 1, 1879

By George F. Weaton

Although an almost continuous campaign had been carried on by various experimenters since 1885 to find a commercial process of smelting zinc by electrothermic means, no commercial success was attained in the United States. The St. Joseph Lead Co., appreciating the theoretical possibilities of such a process, such as the ability to construct units of large capacity, quality control, and the possibility of treating complex and refractory ores, decided in 1926 that the process was worthy of further investigation, and in that year, at one of its southeast Missouri plants, began the development of the electrothermic zinc-smelting process according to the invention of the late Earl C. Gaskill. Late in 1929 the process reached a stage of commercial significance, and in 1930 the erection of a modern electrothermic zinc smelter was begun, at Josephtown, Beaver County, Pa. The site is 3 miles from Monaca, which is on the main line of the Pittsburgh & Lake Erie Railroad, and a spur of the railroad has been constructed to the plant site. The site borders upon the Ohio River, which is navigable for 600 to 800-ton barges. This district was selected for the plant after an economic survey involving such questions as cost and availability of electric power, reduction fuel, transportation facilities, and the transportation charges on raw and finished materials, labor conditions, and taxes. The initial unit of the plant was designed to treat daily 120 tons of 58 per cent zinc sulphide concentrates from the company's mines in St. Lawrence County, New York. The plant equipment is housed in seven modern steel-frame buildings, and includes: Roasting and Acid Plants 3000-ton concentrate storage. Two Nichols-Herreshoff 21 ft. 6-in. diameter, 12-hearth roasters with usual cast-iron airshaft supporting chromium-alloy rabble arms and rabbles. SO2 gas purification system consisting of: One double-compartment hot-dust Cottrell precipitator. Cast-iron sinuous air-contact gas cooler.

Jan 1, 1937

Prof. J. C. BRanner, Stanford University, Cal. (communication to the Secretary): On p. 398, Mr. Hedburg mentions Marionite and Brannerite as ores of zinc. Neither of these has been authoritatively recognized as a distinct mineral species. Marionite, originally described by Elderhorst, was subsequently determined to be nothing else than hydrozincite. Analyses of the so-called Brannerite were sent by me to Prof. Penfield, who says it is a mixture of Smithsonite with some other mineral. On p. 398, Mr. Hedburg says the zinc-bearing formation of North Arkansas " is recognized as the Upper Silurian." So far as my observation goes, the ores occur both in Lower Carboniferous and in Ordovician or Lower Silurian rocks, but nowhere in rocks known to be of Upper Silurian age. If Mr. Hedburg has any paleontological evidence of the Upper Silurian age of these rocks, or of any of them, he will confer a favor upon geologists by making it known. On the same page is another statement in which I cannot concur. He says that in this region, " it can easily be seen that the largest fissure-deposits have been eroded and washed away, leaving here and there a few patches adhering to the hillsides." I am compelled to say that in many years' study of the geology of the region in question, I have never been able to recognize such a state of affairs as Mr. Hedburg here describes. The patches which he regards as remnants of fissure-veins, " adhering to the hillsides," I have found to be either the edges of bedded deposits, or portions of the zinc-bearing breccias, formed along old drainage-lines, and laid bare by the ordinary processes of erosion. That fissure-deposits have been partly removed by the same agency, goes without saying; but it is, in ,my judgment, no more true of North Arkansas than of any other mining-region that erosion has selected and washed away " the largest " deposits. My own views of the region in question are given in detail

Jan 1, 1902

By L. Adler

A fairly complex analysis is required to select or evaluate a piece of excavating and bulk handling equipment for its performance. At present, there is little agreement as to what points should be considered, and even less on what procedure to follow. This paper provides both of these in a consistent and direct form. The analysis applies to all types and sizes of equipment. The importance of the equipment characteristics, job activities, and work conditions are stressed. Separate analytical stems are established in a flow chart for these. They are combined using suitability tests in: problem statement; natural conditions; suitability guidelines; appropriate equipment types; operational activities; encumbered space; geometric design; equipment sizing; failure and limits; performance and consumption; public policy checks; and costs and profitability. Public policy and economics receive emphasis towards the end. The procedure is iterative, containing distinct feedback loops. Specifying the steps and sequence provides a necessary structure which has long been overdue.

Jan 1, 1985

By John S. Sumner

The various electrode arrangements used in induced polarization (IP) surveying can be classified according to the geometry of the electric field being measured. The simplest geometry (Wenner, Schlumberger, gradient) is the parallel or plane-wave electric field, while the three-array and pole-dipole array measure the field about a point current electrode. In the dipole-dipole array the characteristics of a dipolar field are approximately measured. The drill hole arrays employ variations of these fundamental geometries, depending on the objectives of the survey. This report compares the relative advantages and disadvantages of each of the commonly used surface and drill hole IP electrode arrays. Factors of each array that are considered are signal-to-noise ratio, EM coupling rejection, speed and cost, and resolution of polarizable bodies. It is concluded that certain arrays are better suited for different exploration objectives and for different geological conditions. Also the type and capabilities of the IP surveying equipment and method limit the choice of arrays.

Jan 1, 1973

By Carl F. Dietz, Dyke V. Keedy

The problem of drying ores is one that most mill-engvineers are sooner or later called upon to meet, and it may be timely to point out some of the difficulties resulting from such operations from purely a metallurgical and economic standpoint. We mean, in the following pages, to discuss primarily the effect of such operations on the ore. itself, without particular reference to the mechanical or cost features of the subject. That an appreciable tonnage of the ore fed to the usual form of drier, either rotary or stack, is lost, is fairly well appreciated, but we believe that only a few mill-managers know just what their drier-losses amouilt to, and we have found that in most cases they console themselves with the fact that the drier-smoke is not very much discolored, and it is generally believed that the draft is not sufficient to carry away more than a negligible percentage of the values.

Jan 1, 1913

By N. O. Gray, John Henderson

Hydrogen-reduction data for naturally occurring single crystals and Prepared polycrystals of dense hematite have been presented. Results cover the temperature range 400o to 1000oC, for particles from ten sources, ranging in size from 0.07 to 10 mm and in shape from spheres to cylinders, cubes, and thin slabs. A consistent pattern of behavior has been demonstrated for single crystals and the reduction mechanism shown to be temperature-dependent. Below 579oC reduction is a simple topochemical process but at higher temperatuves it is complex and occurs in two distinct stages. Prepared particles from these laboratories behave in a similar manner to the single crystals. Data from two investigators showing topochernical reduction of Prepared particles above 575°C are inconsistent with that for other dense hematites. It is concluded that topochenzical reaction should not be used as a model for generalized rate expressions for dense hematites. SINCE 1958, McKewan1-6 has brought to prominence a simple concept of dense hematite reduction. This model is that oxygen is lost from a hematite particle undergoing reduction only from an oxide-iron interface that recedes in such a way that the oxide remaining retains the original shape of the particle, i.e., reduction occurs topochemically. An adjunct to this concept is that any intermediate oxides in the transition from hematite to iron only form thin layers so that oxygen cannot be lost from the particle without movement of the oxide-iron interface. Further, the rate of oxygen loss from the particle is said to be proportional to the area of the receding interface so that the iron layer grows linearly with time and the over-all reduction process can be described by the equation where ro and do are the initial particle radius and density, respectively, R is the fraction of the original oxygen lost, i.e., the fractional reduction, at time t, and K is the rate constant. The idea of an underlying simplicity in hematite reduction is attractive because it gives a tractable basis from which general theories of hematite reduction can be developed and it has received wide support,7-14 based mainly on the large amount of data13 that can be fitted to Eq. [I]. However, despite the fact that this equation has been derived for dense materials, the bulk of the data that have been used to test it13 have been for materials of only about 90 pct of theoretical density (5.26 g cm-3) or less, so that its generality for dense hematites has not been demonstrated. In any case, as will be seen, adherence of reduction data to Eq. [1] does not necessarily imply that reaction occurs topochemically. In this work only data for hematites approaching theoretical density are considered and it will be shown that in only one study besides McKewan's is topochemical behavior observed over the whole range of temperature investigated. For the majority of materials a linear rate of interface advance is observed to complete reduction only when wustite is not a stable intermediate phase in the transition of hematite to iron, i.e., at temperatures below about 575°C. Above this temperature, reduction is an exceedingly complex series of reactions that takes place in two distinct stages and it is only in the first stage that reaction in any way resembles a topochemical process. This means then that, far from representing general behavior as has commonly been supposed, topochemical reaction for dense hematites is only a particular behavior that may be observed under some circumstances. EXPERIMENTAL Hydrogen-reduction data have been collected and cross-checked in these laboratories by three techniques, weight loss, collection of water evolved in the reduction reactions, and direct metallographic examination. Details of these techniques are discussed elsewhere," where it is shown that results obtained by the three methods are in close agreement. The weight-loss method, by which most of the results were obtained, consisted of hanging the sample in a platinum mesh basket from an Ainsworth Model AV-AU-1 vacuum recording balance inside a vertical l 1/4-in.-ID alumina tube furnace. Dry deoxidized hydrogen was flowed downwards through the tube at 2 to 4 liters min-1 (stp). Single crystals from two sources and artificial oxides from three sources have been examined. The single crystals were from hematite deposits at Yampi Sound, Western Australia, and Brazil, the latter being obtained from Gregory, Bottley and Co., London, U.K. The "Yampi Blue" crystals were hand-picked from washed, magnetically concentrated, sized fractions, -200 mesh BSS (mean diameter ca 0.07 mm) and —36 + 44 mesh BSS (mean diameter ca 0.4 mm) while 10-mm cubes were cut from the Brazilian crystals with a diamond saw. The starting materials for the prepared particles were hematites designated, respectively, "Specpure Iron Oxide", Laboratory No. S639 from Johnson Matthey & Co. Ltd., London, U.K., "Calcined Ferric Oxide" from B.D.H. Laboratory Chemicals Division, Poole, U.K., and "Pigment Grade Oxide", EPR-50, from C. K. Williams & Co., Easton, Pa., U.S.A. Approximately spherical particles were prepared from the artificial oxides by rolling the material, moistened if necessary, in a glass jar, and cylindrical compacts approximately 10 mm in diam and of approximately equal height were pressed in a steel die at 200 psi. These spheres and cylinders were subsequently fired in oxygen for 20 to 100 hr at 1370°C. The

Jan 1, 1967

By D. L. Martin

The study of cobalt-platinum alloys has been of interest since they represent a class of permanent-magnet material in which the disorder-to-order transformation plays a controlling role. The magnetic properties of alloys in the range 40 to 60 at. pct have been found to be greatly influenced by composition and heat-treatment. The peak properties of 4700 coercive force and 9,000,000 gauss-oersteds energy product were obtained by controlled cooling and aging. These high values combined with ductility and machin-ability give the alloys useful characteristics although their high cost limits their application. THE cobalt-platinum alloys have been of interest in the study of permanent-magnet materials ever since the discovery by Jellinghaus that they had unusually high coerceive-force values.' The high coercive force was associated by Jellinghaus with the disorder-order reaction which occurred in these alloys. This was later verified by Gebhardt and Koster in a detailed study.2 An investigation of the structure, mechanism, and kinetics of the disorder-order transformation and resulting property changes in cobalt-platinum alloys has been in progress for some years. Certain phases of this study related to equilibrium rela- tions, and to the mechanism and kinetics of the ordering reaction have been published previously.3-5 In this paper, the results of the processing and heat-treatment studies on 40 to 60 at. pct CO alloys are presented. The magnetic properties have been found to be influenced greatly by the composition, by the cooling rate from the disordering treatment, and the final ordering time and temperature. Coercive force values, Hc, of 4700 oersteds and energy values, (BH)m, approaching 9,000,000 gauss-oersteds have been obtained by controlled cooling and ordering. PROCESSING OF THE ALLOYS The composition range of interest for permanent-magnet properties centers around the equiatomic composition Copt. In this region the alloys are dis-

Jan 1, 1959

By W. A. Ver Wiebe

UNder the impetus of new demands caused by the defense program, the oil and gas industries of Kansas established new records during the year 1941. In all, 2113 wells were drilled, which compares favorably with the record total drilled in 1937. These 2113 tests resulted in 1446 oil wells, 76 gas wells and 592 dry holes. In all three categories there was an increase over the previous year, but unfortunately the most marked increase was in the dry holes. Nearly 80 per cent of the increase must be allocated to the drilling 01 unsuccessful tests. This was partly because of the increasing difficulty of finding new reserve areas and partly because of the erratic character of the production in the Arbuckle dolomite, which is now the main producing zone. Closer analysis of the totals reveals that western Kansas accounted for 1634 tests, of which 1186 were oil wells, 34 were gas wells and 415 were dry holes. The total potential initial daily production uncovered by the successful wells amounted to 1,691,000 bbl. of oil and 508,000,000 cu. ft. of gas. Both figures indicate a considerable decrease when compared with the proceeding year; in 1940 the respective figures were 2,128,000 bbl. and 1,289,000,000 cu. feet. In eastern Kansas a total of 479 wells were drilled. Among these, 260 were oil wells accounting for a daily initial potential production of 45,662 bbl. The new gas wells numbered 42 and added 290,438,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 177 in number, were dry. It is interesting and significant that almost half (791) of the total wells drilled in western Kansas were drilled by the independent operators. Among the large companies the Cities Service Oil Co. drilled 169 wells; the Stanolind Oil and Gas CO., 101; the Skelly Oil Co., 80; the Continental Oil Co., 99, and the Shell Petroleum Co., 63 wells. In eastern Kansas the independent operators drilled 406 out of the total of 479 wells. Among the major oil companies the Cities Service Oil Co. drilled 38; the Phillips Petroleum Co., 13, and the Sinclair-Prairie Oil Co., II wells. The figures on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas approximately one third of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 844 wells in western Kansas, of which 678 were successful in finding either oil or gas. It thus appears that the major companies fared much Getter than the independents. In eastern Kansas the major companies drilled 73 wells of which 63 were successful in finding commercial quantities of oil or gas. No less than 286 wildcat tests were put down in western Kansas and 72 in eastern Kansas, or 358 in all, during 1941. Considerably more than half of these were drilled by independent operators; zoo in western and 66 in eastern Kansas. An exploratory hole % mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, approximately 75 per cent of all wildcat wells were failures; only 25 per cent found oil or gas in western

Jan 1, 1942

By W. A. Ver Wiebe

UNder the impetus of new demands caused by the defense program, the oil and gas industries of Kansas established new records during the year 1941. In all, 2113 wells were drilled, which compares favorably with the record total drilled in 1937. These 2113 tests resulted in 1446 oil wells, 76 gas wells and 592 dry holes. In all three categories there was an increase over the previous year, but unfortunately the most marked increase was in the dry holes. Nearly 80 per cent of the increase must be allocated to the drilling 01 unsuccessful tests. This was partly because of the increasing difficulty of finding new reserve areas and partly because of the erratic character of the production in the Arbuckle dolomite, which is now the main producing zone. Closer analysis of the totals reveals that western Kansas accounted for 1634 tests, of which 1186 were oil wells, 34 were gas wells and 415 were dry holes. The total potential initial daily production uncovered by the successful wells amounted to 1,691,000 bbl. of oil and 508,000,000 cu. ft. of gas. Both figures indicate a considerable decrease when compared with the proceeding year; in 1940 the respective figures were 2,128,000 bbl. and 1,289,000,000 cu. feet. In eastern Kansas a total of 479 wells were drilled. Among these, 260 were oil wells accounting for a daily initial potential production of 45,662 bbl. The new gas wells numbered 42 and added 290,438,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 177 in number, were dry. It is interesting and significant that almost half (791) of the total wells drilled in western Kansas were drilled by the independent operators. Among the large companies the Cities Service Oil Co. drilled 169 wells; the Stanolind Oil and Gas CO., 101; the Skelly Oil Co., 80; the Continental Oil Co., 99, and the Shell Petroleum Co., 63 wells. In eastern Kansas the independent operators drilled 406 out of the total of 479 wells. Among the major oil companies the Cities Service Oil Co. drilled 38; the Phillips Petroleum Co., 13, and the Sinclair-Prairie Oil Co., II wells. The figures on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas approximately one third of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 844 wells in western Kansas, of which 678 were successful in finding either oil or gas. It thus appears that the major companies fared much Getter than the independents. In eastern Kansas the major companies drilled 73 wells of which 63 were successful in finding commercial quantities of oil or gas. No less than 286 wildcat tests were put down in western Kansas and 72 in eastern Kansas, or 358 in all, during 1941. Considerably more than half of these were drilled by independent operators; zoo in western and 66 in eastern Kansas. An exploratory hole % mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, approximately 75 per cent of all wildcat wells were failures; only 25 per cent found oil or gas in western

Jan 1, 1942

By Fred W. Gordon

The North Chicago Rolling-Mill Co., of Chicago, have four furnaces at South Chicago, built during 1881. Each furnace is 20 feet diameter of bosh, and 75 feet total height, the hearth being 11 feet diameter, and the top 15 feet 4 inches. They are blown through seven 7-inch tuyeres placed 5 feet 6 inches above the hearth level. Cubical contents, 15,000 cubic feet. Each furnace is supplied with 2 blowing engines, 84-inch blowing cylinder, and 36-inch steam cylinder, and 54-inch stroke. These two have one jet-condenser worked by an auxiliary pump. The blast for each furnace is heated by the aid of three Whitwell fire-brick stoves, each 21 feet diameter and 60 feet high. In the batteries of boilers furnishing steam for four furnaces there are 36 double-length boilers, 76 feet long, 48 inches diameter and 16,000 square feet heating-surface. The plant was designed to produce 3600 tons per week, or 900 tons for each furnace, and was fitted as above with such engines, boilers, and hot-blast stoves as were thought requisite for that production ; hence, calculated from the present make—not the least remarkable feature is the economy of construction—there are less engines, less boilers, and less hot-blast power for the iron made than at ally plant within my knowledge, or it could to-day be duplicated for less money per ton of iron made per week than could any plant now in existence, whether using fire-brick or cast-iron stoves for heating the blast. This is a practical demonstration of my assertion in a paper on fire-brick stoves, read before the Institute," that the application of fire-brick stoves in construction really lessens the first cost. In view of the statements just made, I must be most emphatic in assuring the members that nothing is strained or overburdened.

Jan 1, 1886

By G. Derge, W. Peifer, J. H. Richards

INTRODUCTION A WIDE variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware. They have been related to hydrogen largely by circumstantial evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British Committee on the Heterogeneity of Steel Ingots,1 and current approaches to the problem were reviewed in a recent symposium of the AIME.12 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principle object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem. The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow cooling. However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross section large enough to develop cracks, yet small enough for convenient handling and sampling. Rails were also selected because they are made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitates early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion. (2) Vacuum extraction (without melting). (3) Total combustion.

Jan 1, 1948

By John H. Hall

The Frémont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about # by 6 by about 16 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Frémont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. In this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions. In testing coupons cut from castings heat treated by quenching and annealing, attention was drawn to the wide variations in the value of the Frémont test of specimens cut from different parts of the coupon. The latter was of the form and dimensions shown in Fig. 1, and Fremont test pieces were cut from two parts of this coupon, marked A and B in that figure. The results of the tests are shown below, tests A and B in each instance being from the same coupon: A. B. A. B. Coupon. Kilogram- Kilogram- Coupon. Kilogram- Kilogram- meters. meters. meters. meters. 1,........ 12.0 12.5 9,........ 27.5 32.5 2,........ 11.0 32.5 10,........17.5 31.0 3,........ 11.5 30.0 11,........ 14.5 31.0 4,........ 20.0 33.0 12,........ 15.0 27.5 5,........ 17.5 33.0 13,........ 19.0 30.0 6,........ 17.5 20.0 14,........ 17.5 25.5 7,........ 17.5 13.0 15,........15.0 30.0 8,........ 10.0 30.0

Jan 1, 1914

By H. M. Merry

The graphic methods and records described in this article have been developed, with satisfactory results, for the use of executives of the Chino Copper Co., in Hurley, N. Mex. Particular attention is directed to the use of large wall-charts, the quick reference display of large charts, the scale notation of metallurgical charts shown in Pig. 3, and the inclusion of mesh extraction on screen analysis diagrams. To properly comprehend the operation and metallurgical results from a concentrating plant, a daily record of essential data is kept, usually involving the dry weight of ore milled or treated, dry weight of concentrate or metal produced, assay values of heading, assay values of tailing, assay values of concentrate, and percentage of extraction or recovery. In addition it is often necessary to record moisture, pulp density, or dilution, percentage of weight of oils and reagents employed; screen analyses of grinding conditions, oversize, etc.; assay values of non-valuable or interfering substances; cost data; and such special information as may be required. GRaphic Presentation . Close analysis is necessary of a daily operation involving such a number of factors, the relation and influence of which may be of great importance in the treatment scheme. When the analysis is made from a numerical tabulation, the chance for one or more obscure, but perhaps important, factors to escape notice is considerable, therefore the need for an accurate, readily digestible presentation of metallurgical data is obvious.. Graphic records of milling operations are frequently used, but owing to the wide range of magnitude and values, and the number of factors involved, the customary practice of assigning different values to the same ordinates, as in Fig. 1, results in a complex and intricate record which makes little appeal to a busy operating official. The methods shown in Figs. 2 and 3 are devised to display such data in a clear and legible manner, without confusion.

Jan 1, 1920

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The ductile fracturing process was studied in single-crystal and poly cvystalline aluminum deformed in tension over a temperature range from 295° to 4.2°K. At temperatures as low as 77°K, the fracture of "inclusion-free" material, including zone-refined aluminum, was by rupture (-100 pct RA). At 4.2 OK, fracture was brought on by adia-batic shear. Metallographic examination did not disclose any voids or slip-band microcracks, thus negating for inherently ductile metals any mechanism of void nucleation by vacancy condensation or of cracking due to dislocation pile-ups. In Izigh-purity aluminum not treated to be inclusion-free, fracture at temperatures as low as 45°K was of the double-cup type and a result of void formation. The reduction-of-area decreased as temperature was lowered, corresponding to the earlier appearance of voids. Such behavior was rationalized in terms of a larger increase, with decreasing temperature, in the .flow stress relative to the strength of the inclusion-matrix interface. Evidence for low-temperature adiabatic shear was found in discontinuous flow at 4.2"K, in the transition to a localized shear fracture at low temperatures, and in the suppression of shear fracture with an elastically hard pulling device. A simple analysis for the initiation of adiabatic shew permitted a general correlation of the various contributing factors. It has been pointed out that the duration of shear depends upon effective mass and elastic stiffness of the deformation system. IT has long been recognized that fracture* may Throughout this paper, the term "fracture" is taken to mean any process that results in the separation of a material into two (or more) parts. Thus rupture as it may be encountered in a tension test leading to 100 pct reduction-of-area is included in this category. occur in a ductile mode, and that the process can be of great practical as well as general interest. Much information about ductile fracture has also been accumulated over this period, but only recently has an understanding of mechanism begun to appear. Ludwik,' in 1926, first reported fracture in a tensile specimen starting with a central crack in the necked section. Since then, other studies have disclosed that such cracks may form by the coalescence of voids nucleated in this region where hydrostatic tension is highest.2-4 Rogers and Crussard et al.' have emphasized void formation and reori-entation along localized shear bands as a mode of crack propagation. pines6 has considered the tensile rod as a bundle of fibers joined by weak interfaces, which subsequently separate to allow individual fiber contraction. The notion of cavity growth and coalescence by purely plastic processes was discussed by Cottrell: who added that the tensile reduction-of-area ought not to be sensitive to temperature. On the other hand, it has been observed that the reduction-of-area is greatly increased if tests are carried out at high temperaturesa or under high hydrostatic pressure.' Fracturing anisotropy in wrought products lends support to the idea of void formation from preexisting flaws strongly aligned by earlier processing.''-l2 There is evidence that many voids result from the fracturing of inclusions or separation at the inclusion-matrix interface Another possibility is that voids grow out of pore volume produced in the initial solidification and never fully removed in later working. In general, a structure 3f particles, pores, and weak interfaces can be expected, at least in materials of engineering interest. Vacancy condensation has been suggested as an alternative mechanism of void formation for materials considered to be inclusion-free.13 Yet experience has shown that tensile reduction-of-area increases with purity, to the extreme of rupture as so often observed in single crystals. Adiabatic shear has an important bearing on ductile fracture. It occurs when the decrease of flow stress, as a result of local temperature rise from heat generated during straining, becomes larger than the increase due to strain and strain-rate hardening. As demonstrated by experiments on punching of plates,14 a large temperature rise may be brought about by rapid straining. Adiabatic flow as a result of the high strain rate reached in an ordinary tensile specimen just prior to separation may account for the cone formation in cup-and-cone fracture;14 evidence of such local heating has been presented.15 For geometrical reasons, however, pure sliding along the conical surfaces is unlikely, and separation under tensile forces is probably an important accompanying feature of the shear.7 In deformation processing operations, a high shear-strain rate may exist at boundaries between plas-

Jan 1, 1964

By J. B. Newsorn

VERTICAL SHAFTS in the United States have heretofore been sunk by blasting and mucking. The blasting leaves uneven, shattered walls which usually must be supported. Even though the walls will stand, shaft lining is needed to furnish supports for the cage guides, pipes, and power conduits. The lining is generally timber, and as timber can be most easily framed into rectangles, rectangular shaft openings are the rule. The timber reduces the size of the cage floor. For example, if the Idaho Maryland company had put down No. 2 shaft by blasting and mucking, the cage area would have been about thirty per cent of the total shaft area. Besides a low percentage of useful area, an ordinary shaft is subject to fire hazard and to timber maintenance charges. It is also poor for ventilation because the timber ribs cause eddies which greatly reduce the speed of the air currents. A bored shaft does not have these disadvantages. The walls are smooth, circular, and not shattered by blasting, so lining is not required in most

Jan 1, 1936