Search Documents

By E. S. Machlin, W. R. Yankee

IN a previous study1 of the effect of heating com-mercial titanium in air on its subsequent friction coefficient against other metals, as well as itself, it was found that the friction coefficient markedly decreased from a value of about 0.7 to about 0.3. A tentative explanation was given that surfaces normally produced at room temperature are not contaminated sufficiently to prevent seizing or welding of the titanium to the softer mating metals. The latter tend to cleanse themselves during rubbing over the harder titanium. It was thought that the lack of a contaminant protective film on the titanium was due to the high solubility of titanium for oxygen and nitrogen and hence an inability to form a contaminant oxide or nitride. This explanation requires the ratio of the surface absorption rate to the diffusion rate to become much lower at room temperature than it is at high temperatures. In order to check the phenomenon further, commercial titanium specimens were nitrided or oxidized at 800°C for 20 hr in flows of prepurified N2 and 01, respectively, at about 1/2 in. H2O above atmospheric pressure. Friction runs were made in argon using a freshly cut copper hemisphere (cut in argon) on surfaces cut successively into the diffusion layers in the titanium (cut in argon) using the techniques described in a previous publication.' DPH values (100 gram load) were made as a function of depth into the diffusion layer using a Tukon tester. Also, micrographs were taken at separate cross sections to indicate the diffusion layers. The results obtained are presented in Figs. 1 and 2, which show the "static" friction coefficient vs hardness for the nitrided and oxidized specimens, respectively. A separate measurement of the friction coefficient of clean copper vs iodide titanium also was made. From results reported in the literature' giving the oxygen and nitrogen contents as functions of the hardness, cross plots were made showing the friction coefficients as functions of the amount of interstitial solute. These plots are given in Figs. 3 and 4. From micrographs of the diffusion layers and the phase diagrams, it was deduced that the data in Figs. l through 4 correspond to the single phase a region. The points observed on the compound regions have been excluded from the figures. It is apparent that nitrogen or oxygen in solution in the a titanium markedly affects the friction coefficient against a softer mating metal. Discussion of Results These results are extremely interesting from both a practical and theoretical viewpoint. The theoretical implications will be discussed first. According to Bowden, the friction coefficient should be given to a good approximation by the relation where a is the fraction of contact area that has welded, a is the shear strength of weaker component, and H is the hardness of softer component. Using this relation alone, it is difficult to understand the results because none of the terms should be affected by a variation in the oxygen or nitrogen content of the harder and stronger metal, titanium. Even if the ratio of S/H for titanium is used in Eq. 1, the ratio has been shown to be independent of oxy-gen or nitrogen content.' If a more rigorous equa-tion is used combining Eq. 1 and a result given pre-viously" for the case where welding is absent, then the relation obtained is µ = a S/H + (1-a) a W aß/H where a is constant and Waß is the work of adhesion between the two metals comprising the friction couple. This relation states that if a is less than 1/2 or so, variation in the work of adhesion Waß between copper and the titanium should affect the friction coefficient markedly. It is reasonable to expect that the work of adhesion will depend on the oxygen or nitrogen content of the titanium. Available data4 show that clean metals and oxides have much lower works of adhesion than the same metals against the

Jan 1, 1955

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZg2, (formerly ASTM No. 17; also known as Dowmetal C or AM26o) which was done under "Restricted" Project NRC-2I, in 1942-1943, and reported in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat- treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZp was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZp, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray 'analysis. From this figure it may be seen that above approximately 375°C (707OF), AZp alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, ancl because of its solubility relations, AZqz resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ² alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1949

By Frank Fahrenwald

I. INTRODUCTORY METALLURGICAL research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likely that a material can be produced which will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may, be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series' has shown that alloys of those metals may be produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties-including the ease with which

Jan 1, 1916

By Harry L. McNeill

THE Selective Media Process was developed by the author in a laboratory provided by The Steårns-Roger Manufacturing Co. It is the outcome of an [ ] investigation into the possibilities of coarse beneficiation by sink and float without using the conventional heavy media. Commercial work to date has been limited to the treatment of minus 3/8-in. iron ore at the Hill Trumbull washing plant of the Cleveland Cliffs Iron Co., at Calumet, Minnesota. Two cut away prints of the machine are shown (Figs. I and 2). A rotary conical impeller is mounted within a stationary cone (Fig. 2). This impeller is adjustable vertically by a 12-ton screw jack. The speed of the impeller can be varied from 14 to 32 r.p.m. by the Reeves variable-speed motor pulley mounted on the 7 ½ -hp. motor drive. Attached to the bottom of the stationary cone is the automatic control valve for sink product, actuated by a ¼ -hp. gear motor. The sink product is dewatered in a conventional drag driven by a 7 ½ -hp. motor and discharged onto an inclined conveyor containing from 6 to 10 per cent moisture. Two plants are operated at the Hill Trumbull property. All the ore is first treated in a typical washing plant (Fig. 3). When treating "wash ore" a finished concentrate can be produced by the log washers and Akins classifiers, as the separation involves only fine silica (minus 48-mesh) and free iron. However, when "jig ore" is fed to the washing plant the coarse

Jan 1, 1946

By Raymond C. Johnson

GASIFICATION is important to the anthracite industry, as it is to the entire solid-fuel industry and to the nation. However, to the anthracite industry it may have particular significance in that it would increase the market value of many millions of tons of a by-product fuel, which the industry now has in storage and is currently producing, in addition to increasing the potential market for all its products. The by-product fuel is of usable quality but the ash content is higher than it can be in other products and therefore it must be converted or used at the point of production. Gasification is one method by which the product may be given increased value. The inherent characteristics of anthracite make it well suited for producing a fuel or synthesis gas. It is the most concentrated form of natural commercial carbon, noncaking and noncoking; it does not produce smoke, tar, or soot and has a low sulphur content; and the volatile matter, which ranges between 2 and 8 pct, is 80 to 85 pct hydrogen with small amounts of methane, carbon dioxide, carbon monoxide, and nitrogen. The ash fuses at high temperatures, which allows it to be burned at high rates without slagging. However, with the addition of small amounts of dolomite, the ash will form a slag, or glass, which is very fluid. Anthracite has long been used in the manufacture of city gas and it is extensively used in various parts of the country to make water gas to be converted to hydrogen. Buckwheat and rice anthracite are used in Galusha producers to make producer gas. Excellent synthesis gas has been made in a Galusha producer with rice and barley anthracite with oxygen in tests at the Consolidated Mining and Smelting Co., Trail, British Columbia. In these tests, anthracite was shown to have advantages over competitive fuels, in that the gas had a higher hydrogen content and could be cleaned with less difficulty. The anthracite seams are steeply pitching and in mining the parting strata and some of the roof and bottom materials are taken with the coal. In preparation, these materials are separated by gravity from the commercial product and stored in refuse banks. This refuse contains a mixture of rock, slate, or shale, and high-ash anthracite with bone coal, which is low-ash coal that is interspersed with thin bands of shale. The bone coal contains between 25 and 50 pct ash with an average ash content of approximately 30 pct, with a

Jan 1, 1953

By J. Groyecki, M. Markuszewicz, J. Lassota, A. Zawada

The ratio of stable to unstable inclusions was found to ploy an essential role in the process of sccorldar-y recrystatlizalion in Si-Fe. The analysis of the free energy of inclusions in the range of heat-treatment of individual inclusions to be predicted. The effects MnS. ns inslable inclusions. were investigated. TO secure a high induction, the secondary recryslulliztt-lion associated wilh the texture is necessary. To obtain a low core loss an additional refiuing in the solid state is required. It has been found that sulfur can be more easily removed in racunm than in hydrogen and thai this process was hindered by the prescrzce of INCLUSIONS play an essential role in the development of cube-on-edge texture in Si-Fe. Their function consists in restraining the growth of primary grains up to about 900°C and in passing subsequently into solution at higher temperatures. This process is accompanied by the selective growth of secondary grains with (110)[001] orientation. The general effect of inclusions depends on such factors as the type of impurities, their amount. dispersion and stability, the conditions of diffusion in the space of lattice of metal, and the reactions at the metal/gas interface. In recent years, some of these factors were the subject of a special investigation. A positive influence of Mns, siN,' and vN3 has been established. The quantity of impurities4 and their dispersion5 have been found to be of major importance. Attention was called to the vital importance of diffusion and the conditions under which the impurities are removed from metal., It has also been demonstrated that in Fe-Si alloys by the techniques of powder metallurgy a special opportunity exists to obtain the (110)[001] type texture. 6 The aim of this work was to conduct qualitative investigations on the influence of inclusion stability on the development of cube-on-edge texture in a metal containing approximately 3 pct Si. Experiments were carried out on cast alloys and on those manufactured by powder-metallurgy techniques. The results obtained from these experiments were utilized to explain the phenomena involved and to analyze the relationships between stable and unstable inclusions and the magnetic properties of alloys. EXPERIMENTS AND RESULTS The raw materials used in these experiments were the powder of carbonyl iron with the analysis (in pct) 0.044 C, 0.01 Mn, 0.005 Si, 0.009 P, 0.002 S, traces of Cu, 0.06 Ni, 0.0015 Al, 0.03 Cr, 0.02 Mo, 0.01 Ti, 0.002 Co, traces of Pb, and the powder of silicon containing 94.14 Si, 0.003 S, 0.048 C. The powders were ground and mechanically mixed in 100-g batches. and then pressed at 9 tons per sq cm into 74 by 24 by 8 mm blocks. Sintering was carried out at 1100°C for 12 hr in vacuum (2 x lo-' Tr) or in hydrogen. In this instance the material was heated slowly and subjected to prolonged soaking at 350°, 650°, and 750 2C, respectively, to secure reduction of ferro-oxides. This was checked by making measurements of the dew point, which was found to change from -15" to -35°C after reduction. The compacts after sintering were hot-rolled to 2.4 mm, annealed at 800 C, and finally cold-reduced to 0.35 mm with intermediate annealing at 800°C at a gage of about 0.8 mm. Impurities were added in the powdered form and mixed with iron and silicon powders. Sulfur in the elemental state, electrolytic manganese, and pure aluminum oxide were employed. Besides, to obtain a material with low contents of impurities, especially

Jan 1, 1967

By W. H. Emmons

This paper is the third of a series treating of the relations of ores of the metals to igneous rocks. The first' outlined the general problem; the second2 proposed a classification of lode ores, and showed how the distribution of the deposits is in a certain measure controlled by the contour of the roof of the parent batholith. A number of mining districts were discussed, the examples being selected chiefly from group 2 of the classification. The proposed classification of lode deposits, briefly stated, is as follows: 1. Cryptobatholithic: near hidden batholiths which have not yet been exhumed by erosion. 2. Acrobatholithic: in and near cupolas or domes of batholiths—the high points of larger underlying masses. 3. Epibatholithic: on batholiths, near their rims, but below eroded cupolas, or below the highest points of the roofs. 4. Embatholithic: among closely-spaced outcrops which probably are parts of a single bathohth. The outcrops of invaded rocks predominate. 5. Endobatholithic. in and near roof pendants of large batholiths. The invading rocks predominate. 6. Hypobatholithic: in deeply-eroded batholiths, where even roof pendants have been eroded. Deposits of certain metals on the roofs of the batholiths are much more numerous in some positions than deposits of other metals, and the horizontal zonal arrangements of lodes of different metals are shown characteristically only in certain groups. In a large measure, also, the character of the fracturing and metallization is determined by the position on the roof of the batholith. The disseminated copper ores in porphyry constitute a clearly-defined type. All the deposits of these ores, as far as known, are in group 2. They appear to have been formed only in and around small upward projections of the parent granitic masses, and not low on the walls of the

Jan 1, 1927

Jan 1, 1924

By Howard Martens, Pol Duwez

IN two papers published in 1949, alloys of chromium with the refractory metals tungsten, molybdenum, tantalum, and columbium were investigated in view of their possible use as high temperature resisting materials. For the Cr-Ta system, a partial phase diagram was presented and the only intermediate phase was identified at Ta2Cr3. A phase of the same composition was also observed in the Cb-Cr system. The X-ray diffraction data presented in these papers, however, were insufficient for crystal structure determination. It is shown in the present study that the only intermediate phase in both the Ta-Cr and the Cb-Cr systems corresponds to the ideal stoichiometric ratio TaCr2, or CbCr2. Both structures are cubic, MgCu, type. At high temperature, however, TaCr2 has a hexagonal MgZn, type structure, which can be retained at room temperature by fast cooling. The alloys were prepared by melting in a helium arc furnace on a water-cooled plate. The design of the furnace was essentially the same as that described in ref. 3. Some alloys were also obtained by sintering compacts made of the mixed powders pressed at 80,000 psi. The sintering was carried on for 4 hr at 1375°C. The tantalum and columbium powders were supplied by Fansteel Metallurgical Corp., North Chicago, 111. The tantalum powder was the reagent grade, with a particle size smaller than 400 mesh and a total impurity content less than 0.1 pct. The columbium powder was smaller than 325 mesh and contained approximately 0.1 pct C and traces of Fe, Ti, and Zr. The electrolytic chromium powder from Charles Hardy, Inc., New York, was smaller than 300 mesh and contained about 0.1 pct Na, 0.05 pct Ca, and traces of Cu, Al, Mg, Si, and Co. Powder diffraction patterns were obtained with a 14.32 cm camera, using copper Ka radiation filtered through nickel foil. The powder pattern of the TaCr2 alloy obtained by sintering at 1375'C was different from that obtained on the same alloy rapidly cooled from the melt. Contrary to this result, the powder pattern of CbCr2 was the same, whether the alloy was made by sintering at 1375°C or by melting, and was similar to that of the TaCr, sintered. It was also found that the structure of the TaCr2 specimen obtained by melting was retained after heating for 4 hr at 1590°C, but transformed into the structure found in the sintered specimen after heating for 4 hr at 1375°C. Hence, the structural change of TaCr2, appears to be a reversible polymorphic transformation. CbCr2 and ToCr2 Structure, Low Temperature Form By using large scale Hull-Davey charts, the powder pattern of CbCr, and of the low temperature form of TaCr2 were readily interpreted on the basis of a face-centered cubic lattice with a parameter of approximately 6.95 kX. The indices of the reflections together with the values of sin' 0 are given in Tables I and 11. From this list of observed reflections, it appears that the (200), (600), (024), (046), and (028) reflections are missing. The lack of (h00) reflections for h 4n indicates a four-fold screw axis. The missing (Okl) spectra for k + 1 An indicate the existence of a diamond glide d. The combination of these symmetry elements can be found in the O— Fd3m space group, which is therefore the most probable one. After having determined the approximate density of TaCr, by the immersion method, the number of molecules per unit cell was calculated and found to be nearly eight. This information, added to the fact that the most probable space group is O leads to the consideration of a structure of the MgCu2 type, in which the atoms have the following positions: 8 magnesium in a and 16 copper in d. On the basis of this structure, intensities were computed by means of the usual formula: 1 cos'20 I a sin2 cos where F is the structure factor; 8, the Bragg angle: and p, the multiplicity factor. As shown in Tables I

Jan 1, 1953

Jan 1, 1924

A discussion at a joint meeting of the New York Section of the American Electrochemical Society and the American Institute of Mining Engineers, Nov. 20, 1913. Chairman Lawrence Addicks:-Our program this evening represents an attempt to set before you the present situation and outlook in the metallurgy of zinc. It is a time-honored custom to throw bricks at the zinc man. The accusation is that he has borrowed a lime kiln and a gas retort and part of a sulphuric acid plant, hitched them together, and spent the last 50 years in regarding with holy veneration the reactions which take place in that retort. The copper man, who thinks of zinc as something with which copper is adulterated to make brass, and the iron man, who regards it as a sort of paint for corrugated sheets, and the lead man, whose opinion as to zinc is not fit for publication, have long felt that, when two or three of the minor details of their respective metallurgies were put in order, they would take a few clays and fix up zinc on a modern basis. But somehow there still seem to be some unsolved problems at home, and while we are waiting it seems only fair that the case for the defense should be adequately presented. There is probably no man in this country to-clay better able to do this than Mr. George C. Stone, of the New Jersey Zinc Co., on whom I have pleasure in calling to talk to us on "Progress in the Metallurgy of Zinc." George C. Stone:-It is frequently stated that there has been no change in the metallurgy of zinc since the first Belgian furnaces were built in the early part of the last century. It is true there have been no such spectacular and radical changes as were worked in the metallurgy of copper and iron by the introduction of converters; but, in the essentials, I believe the progress in zinc metallurgy has been as great as in that of the other common metals. The main reason that there have not been revolutionary changes is that the chemistry of zinc differs radically from that of the other metals and these differences control the type of apparatus that can be used. The differences are: 1. The temperature at which zinc is reduced by carbon is much above the volatilizing point of the metal and it is therefore always produced as a vapor.

Jan 1, 1914

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

A generalized mathematical model has been developed to describe the kinetics of gas-solid reactions with special attention given to the hydrogen reduction oj dense spheres of hematite. This reduction process must pvoceed through a sequence of transport and chemical .reaction steps acting in series. Under typical experimental conditions, none oj the individual transport and reaction resistances may be neglected in the development of a physically significant model. A linear vate of thickening oj the product layer, usually taken as evidence of interface-controlled .reuction, may be observed even though transport resistances play a dominant role in the over-all kinetics. The temperature and pressure dependencies of all terms have been carefully evaluated in order to .make fill use oj arailable expe-inzental data in evaluation oj the model. FOR obvious technological reasons, the kinetics of reduction of iron oxides has become the subject of intensive experimental and theoretical investigation during recent years. Continuing efforts to construct mathematical models to describe the kinetics of reaction between a gas stream and a granular bed of solid particles have demonstrated the necessity of a thorough understanding of the reaction kinetics of a single particle within the system as a prerequisite to the construction of physically significant models of complex, reacting systems. This paper presents a critical examination of the transport and chemical-reaction processes involved in single-particle oxide reduction and develops the mathematical expressions necessary to evaluate their importance. Comparison of theoretical predictions with experimental results contributes important new understanding of the complex nature of this process. The reduction process has been studied under a wide range of experimental variables, and it is not surprising that apparent conflicts in observation and interpretation appear in the literature. The interested reader is referred to the reviews of Themelis and auvin"? and Manning and philbrook3 for a description of much of this work. The course of reaction commonly has been followed by measuring the oxygen weight loss from the particle as a function of time. A number of authors have suc- cessfully correlated their data in terms of a model which assumes that the reduction process is controlled by the rate of reaction at a single, sharply defined, advancing interface. According to this model, the interface will advance linearly with time. A mathematical model for gaseous reduction in a packed bed developed by the present authors in an earlier paper4 recognized that reduction must proceed through the series hematite (Fe203), magnetite (Fe30,), wiistite (Fe,O), and finally metallic iron. The reduction scheme permitted a stepwise topochemical reduction of the individual particles to metal or to the lowest oxide thermodynamically possible for the local gas composition in the bed. The limiting situations of theoretically dense and very porous oxide structures were considered. On the basis of available experimental evidence, the simplifying assumption was made in each case that all product layers would thicken linearly with time. A generalized single-particle model has now been developed to determine the significance of transport resistances in the product layers and in the gas film surrounding the particle. The analysis shows that the interplay of transport and chemical resistances is such that an apparently linearly advancing interface may be observed despite the fact that the reaction may be under significant transport control. Attention thus far has been focused on the development of a model for the topochemical behavior of dense spheres of hematite in atmospheres capable of reducing them completely to metal. The formation of successive product layers of iron, Fe,O, and Fe304 is assumed to follow the mechanism originally described by dstrijm.' All oxygen removal from the core occurs at the iron/Fe,O interface, intermediate oxide layers being propagated by sol id-state diffusion without change in the oxygen density of the core. Since fractional reduction is operationally defined in terms of oxygen weight loss, the kinetics of the over-all reduction of FeZ03 to iron is properly studied in terms of the gas-solid reaction occurring at the iron-wiistite interface. The fractional reduction of a partially reduced oxide sphere is given by: here refers to the radial position of the iron/Fe,O interface. This model is not universally applicable because, as explained in the earlier paper,4 a consideration of porous particles or of dense particles in atmospheres not capable of reducing wiistite must allow for the possibility of gaseous reduction at interfaces other than the one between iron and Fe,O. However, evidence that certain hematite specimens actually do follow the dense-pellet mechanism developed here is provided by the data of cewan' and of Bogdandy and

Jan 1, 1967

By J. J. Jonas, J. L. Uvira

Equipment was constructed which permitted the hot compression of 99.8 pct Armco iron and 2.8 pct Si steel at constant true strain rates of 0.05 to 1 per sec over the temperature range 600" to 1000°C. A maximum true strain of 1.9 could be attained, followed by immediate quenching or by isothermal annealing. True stress-true strain curves were obtained, and the steady-state flout stress, a, strain rate, i, and temperature, T, were found to fit the following expression: The constants A, a, n', and AH were determined for the two ,materials. The activation energies obtained for Arrnco iron and silicon steel are 66 and 80 kcal per mole, respectively, and approximate those for seu- diffusion and for creep. This indicates that hot compression is a diffusion-controlled thermally activated process. THE hot compression of iron and steel is usually carried out in the austenite temperature range,1"7 as this is the one of greatest interest with respect to industrial hot working. However, a disadvantage of testing in the austenite range is that the hot-worked structure is destroyed by the phase transformations taking place during cooling. The present study was therefore carried out in the ferritic temperature range, and the hot-worked substructures were preserved by rapid quenching after deformation. The substructural results will be described in a separate paper, and the present communication is restricted to the strain rate/stress/temperature relationship observed during hot working. The results of hot-compression testing are usually given in the form of true stress/true strain curves, with a different curve for each temperature/strain rate ~ornbination.',~,~ Sometimes simple algebraic equations are fitted to the curves, so that certain extrapolations or interpolations can be performed.1'2'5 These equations are, however, devoid of mechanistic interpretations. The present study was undertaken to show that hot compression can be described by an equation of the type used in creep studies. That is, it will be shown that the temperature dependence of the strain rate in hot working is well-represented by an Arrhenius term, with an activation energy similar to that for creep. Also it will be seen that the stress dependence of the strain rate is similar to that for creep EXPERIMENTAL METHOD AND MATERIALS The investigation was carried out with the following three ferrous materials: 1) Armco iron; 2) Armco iron with 0.26 pct Mn; 3) 2.8 pct Si steel. The first two materials were utilized for investigations performed in the temperature range 600" to 800°C; the last one was used for tests at temperatures from 600" to 1000°C. The materials were of commercial purity,* as shown in Table I. Cylinders of five different sizes were prepared by strain annealing. The resulting mean grain diameter was 3 mm in the 1-in. Armco iron and 2 mm in the other sizes and grades. Different ratios of diameter/height were used to enable the determination of the coefficient of friction. The specimen faces were provided with concentric grooves, which acted as lubricant holders during compression, as recommended by English and ~ackofen' and others.2'9 Powdered glass lubricants were applied to the samples before hot compression to decrease friction and barreling, following the practice of previous investigator~.~~~~~~~~ Different mixtures of glass powder were used for each temperature, after the determination of suitable compositions by experiment.'' Equipment for Hot Compression. Hot-compression tests were carried out on an adapted 150-ton vertical hydraulic extrusion press and also on a modified high-temperature creep machine. The modified extrusion press was used for temperatures up to 800°C. The following items were added to the press: a) a high-temperature furnace with built-in upper and lower platens; and b) a transmission assembly, which permitted the attainment of logarithmically decreasing crosshead speeds. These accessories are described in detail in Ref. 11.

Jan 1, 1969

By L. M. Yokum

Tremendous strides have been made in front end loaders in the last 15 years. Fifteen years ago a 21/4-cu-yd front end loader was the largest standard machine you could purchase. Today there are two commercially available 15-yd front end loaders and many 10-yd loaders. The estimated total worldwide market for all front end loaders over 1 cu yd has increased to over 30,000 units yearly. The trend for front end loaders, in general, and for the mining market, in particular, is to larger and larger loaders. Today there are 18 and 24-cu-yd front end loaders in prototype form. It is not inconceivable that within another 15 years there will be front end loaders in the 50-cu-yd class with design features quite different from today's. These larger loaders are being designed at the demand of the mining industry, and the design criteria are being directed at this market area. The costs of these larger loaders may be greater per unit of capacity, but it is the intent of the various manufacturers that they will be more reliable, be easier to service, give greater availability, live longer, and cost less to maintain, than previous loaders. It is also the intent of the manufacturers to compete directly with the large mining shovel as the front end loaders become appropriately larger and more reliable. There has been some trend in this direction in the past with smaller shovels and loaders. In Table 1 are data for U.S. production of front end loaders (5 to 6-cu-yd class and 10-cu-yd class) and U.S. production of cable-operated, crawler-mounted power shovels, draglines, and cranes (11/z to 5-cu-yd class) for the years 1965 and 1970 (Source: Bureau of Census, U.S. Department of Commerce). Many believe that the decline in shovel production, in particular, is due at least in part to the acceptance of the front end loader as a primary production tool. However, the foregoing comparison is for a smaller shovel class than for front end loaders. It has generally been a rule of thumb that a front end loader is competitive on a cost and production basis with a shovel when it is approximately twice as large as the shovel. This same relationship may not hold true with the larger 10 to 15-cu-yd electric shovels, but at some point, direct competition will probably occur. Current Trends There are many trends today that are significant. One major usage trend in large front end loaders involves load and carry operations. This application is defined as "performing the functions of loading, hauling and dumping with one machine over distances within its economical limits." Many people are using front end loaders to transport material as well as load it. It is estimated that nearly half of all 10-cu-yd front end loaders sold in 1970 went into primary load and carry work. Many times, significant savings result from using the load and carry system, instead of small truck and shovel operations, for distances in excess of 1000 ft. Strip mining in coal utilizes great numbers of front end loaders in this manner. In-pit crushing of limestone is developing on an ever-increasing level, especially in Europe, and this stimulates interest in load and carry operations. In Table 2 is a cost example for 10-cu-yd front end loader in a limestone quarry. More than likely, load and carry use will continue to increase over the next few years. While some types of mining do not lend themselves to load and carry in the pit, such areas as surge piles are applicable and should be studied. In the area of machine operating cost reduction, there

Jan 1, 1974

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson's Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson's Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson's Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile ''Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson's Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson's Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson's Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile ''Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951

1. A passenger rickshaw in China. 2. A Pekin cart carrying coal, on dirt roads; the cost works out to 15 or 20 c. per ton-mile. 3. Coolie with wheelbarrow. This one has a small load, but barrow men carry ordinarily 250 lb., occasionally 400 if with a helper. He goes about 18 miles a day and the cost is about 25c. gold per ton-mile, though it varies widely. 4. Coolie delivering coal balls in Pekin. He carries about 65 lb. On some roads with a different arrangement a coolie carries 133 lb., making about one ton-kilometer per day. 5. Truck used by the Government Fuel Yard at Washington. Carries 71/2 tons in an hour as far as a barrow man carries 1/4 ton in a day.

Jan 8, 1928

By J. E. Hilliard, H. E. Cook

It is shown that for systems having a miscibility gap the spinodal composition (c,) in the vicinity of the critical temperature (Tc) is related to the equilibrium composition (c,) by where cc is the critical composition. This expression is exart for the limit T — Tc and is a good approximation down to (T/Tc) - 0.9. If the miscibility gap meets the composition of the pure components THE recent theoretical treatment by cahn1,2 on spinodal decomposition of solid solutions has revived interest in methods of estimating the chemical spinodal, * i.e., the locus on a binary phase By use of the appropriate expression, the spinodal can be drawn on the Phase diagram almost by inspection with an accuracy comparable to that of lengthy calculations in which a free-energy function is fitted to the phase diagram. Satisfactory agveemenf is also obtained with spinodals comPuted from experimental free-energy curves. where G is the Gibbs free energy of the homogeneous solution and c the atomic fraction of component 2, the derivative being evaluated at constant temperature (T) and pressure (P). (These subscripts will hereafter be omitted from the partial derivatives.) If experimental measurements of G as a function of c and T are available in a single-phase region above the spinodal, then these can be extrapolated to obtain a series of metastable free-energy isotherms in the two-phase region, and from these isotherms a series of spinodal compositions can be calculated. Because the value of is very sensitive to experimental errors, an elaborate analytic procedure is required for

Jan 1, 1965

By Cyril Smith

IN the study of the structure or the properties of a series of alloys or nonmetallic compounds, it is often advantageous to express the com-position not as percentage by weight, according to which the material is always made up and analyzed, but as the atomic percentage of the two constituents. The conversion from the one to the other is repre-sented by the formulas: 100A 100x or 1 x/A+100-x/B B(100-x) _ 100yA 100y [2] X. yA + (100 - y)B or y (100 - y) where x and y are the weight and atomic percentages respectively of the element of atomic weight A, and (100 - x) and (100 - y) are the per-centages by weight and by atoms respectively of the element of atomic weight B. While calculations according to these formulas are simple, they are time consuming if several conversions have to be made. In 1931 Water-man1 constructed a nomograph for performing the conversion, but this did not permit an accuracy greater than about 1 per cent to be obtained in the neighborhood of 50 per cent. Ölander2 has proposed a graphic method simpler than Waterman's and one that gives a uniform precision throughout the entire scale. The possible accuracy is about 0.5 per cent of the whole, depending on the size and accuracy of the coordinate paper used. Recently, Hermann3 has described a slide rule for making the calculations. These devices make use of the simple rearranged equation

Jan 1, 1933

By Cyril Smith

IN the study of the structure or the properties of a series of alloys or nonmetallic compounds, it is often advantageous to express the com-position not as percentage by weight, according to which the material is always made up and analyzed, but as the atomic percentage of the two constituents. The conversion from the one to the other is repre-sented by the formulas: 100A 100x Y x 100 ? x/A A [1] A+ B x + A/B(100-x) X _ 100yA 100y [2] yA+(100-y)B or y+A(100-y) where x and y are the weight and atomic percentages respectively of the element of atomic weight A, and (100 - x) and (100 - y) are the per-centages by weight and by atoms respectively of the element of atomic weight B. While calculations according to these formulas are simple, they are' time consuming if several conversions have to be made. In 1931 Water-man' constructed a nomograph for performing the conversion, but this did not permit an accuracy greater than about 1 per cent to be obtained in the neighborhood of 50 per cent. Olander2 has proposed a graphic method simpler than Waterman's and one that gives a uniform precision throughout the entire scale. The possible accuracy is about 0.5 per cent of the whole, depending on the size and accuracy of the coordinate paper used. Recently, Hermann3 has described a slide rule for making the calculations. These devices make use of the simple rearranged equation:

Jan 1, 1933