Search Documents

By Eric R. Jette, Earl S. Greiner

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. 'This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,' who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943

By Earl S. Greiner, Eric R. Jette

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. 'This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,' who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943

By R. Simon, L. Yarborough

This paper presents a correlation for predicting the critical pressures of gas-solvent-reservoir oil systems of the type encountered in gas and solvent injection processes. Experimental data from 14 systems were used to develop the correlation which expresses critical pressure as a function of composition, C7+ mol weight, and C7+ characterization factor. Critical pressures predicted by the correlation for the 14 gas-solvent-reservoir oil systems have an average deviation of 2.8 per cent of the experimental values. The correlation war used to study a wide variety of other hydrocarbon mixtures reported in the literature whose critical conditions are in the range of interest in oil recovery work (100 to 280F and 2,000 to 6,000 psia). Critical pressures predicted by the correlation had an average deviation, expressed as per cent of experimental value, of 5 per cent for 20 miscellaneous mixtures from the literature, and 6.4 per cent for I7 methane-butane-decane mixtures reported by Sage and Lucey. INTRODUCTION Predicting critical points of hydrocarbon mixtures is an important part of phase behavior calculations. If the critical point can be predicted for a specific mixture, the separation between the bubble-point and dew-point regions will be defined, and physical properties of the mixture can be calculated by using the principle of corresponding states. Numerous correlations for predicting critical points of hydrocarbon mixtures have been published. Six of these correlationsl-8 were for light hydrocarbons, and two correlations7,8 ere for high boiling-point petroleum distillates. Organick9 And Eilerts" presented correlations which combined the published data from both light and heavy mixtures, and these correlations became the only available methods for predicting critical pressures for wide boiling range mixtures. In the course of the authors' work on secondary recovery by gas and solvent injection, experimental data were obtained for 14 mixtures of dry gas, ethane-propane-butane solvents, and various reservoir oils. The critical pressures and critical temperatures of these gas-solvent-reservoir oil systems were in the range of 1,900 to 4,800 psia and 180 to 265F. The critical pressures predicted for the 14 mixtures by the correlations of Organick and Eilerts had an average deviation from the measured values of about 13 per cent. The authors felt that it was necessary to develop a better correlation for engineering calculations and the resultant correlation, which is presented on Figs. 1 and 2, predicts the critical pressures of the 14 mixtures with an average deviation of 2.8 per cent. The validity of the correlation was tested by applying the correlation to other hydrocarbon mixtures reported in the literature. This subject is discussed later in the paper. The authors feel that there is also a need for an improved critical temperature correlation for gas-solvent-reservoir oil systems. However, developing a critical temperature correlation is a significant study in itself and is not included in this paper. EXPERIMENTAL DATA The compositions and critical points obtained by the authors for 14 gas-solvent-reservoir oil mixtures are shown on Table 1. The methane concentrations in these mixtures varied from 20 to 63 mol per cent. The intermediate hydrocarbon group, consisting of ethane, propane, and butane, varied from 20 to 64 mol per cent, and the concentration of the C,, fraction from 10 to 20 mol per cent. The physical properties of the C,, fraction covered the range from light, paraffinic, nonasphaltic (Mixtures 5, 6, 7, 8, 9 and 10) to heavy, aromatic, and asphaltic (Mixtures 13 and 14).

By Riki Kobayashi, Donald L. Katz

The dew point of natural gas which has been in equilibrium with gas hydrates has been reported to be lower than that obtained for natural gas in equilibrium with water1,? Hammerschmidt' reports a lowering of the dew point of 13 F for a natural gas in equilibrium with hydrate at 380 F and 525 psi. Records and Seely2 likewise show that the dew point of gas leaving hydrate separators' is as much as 150 F below the separator temperature. This paper presents the reasons for the observed differences between the equilibrium temperatures and the dew point temperatures. Descriptions of the dew point determination by the Bureau of Mines and ASTM tester3 indicate that the dew point is taken as the temperature at which liquid water droplets first begin to appear on the cooled mirror surface even though the temperatures involved are below that required for the formation of gas hydrates or ice. PRESSURE-TEMPERATURE DIAGRAM FOR METHANE-WATEK SYSTEM Fig. 1 presents a schematic pressure-temperature diagram for the methane-water system" for some constant pressure between the critical pressures of pure methane and pure water i.e., pressures frequently encountered in pipeline operations. The possible equilibrium relations are shown by the heavy solid lines. Curve AE represents the saturated water content or dew point of gas in equilibrium with a water-rich liquid solution while curve EF represents the dew point of gas in equilibrium with hydrates. In addition the dotted line DE labelled "metastable dew point" is introduced to explain the apparent discrepancy betwceen the dew point determination and gas-hydrate equilibria. Thermodynamics place certain restrictions on the location of line DE6, namely, that (1) the concentration of water along the line DE be greater than the concentration of water along EF or that the metastable line split the angle formed by the intersection of line GE and EF

Jan 1, 1956

By Paul Queneau

FROM the first days on the Norman beaches to the last days on the Elbe the Army Engineers of World War II lived off the countryside for the great bulk of the construction supplies needed for the fulfillment of their ultimate mission-to keep the army moving. To accomplish this end, vast tonnages of rock, timber, and steel were required in the construction of roads, railroads, and bridges. Combat Engineer battalions operated quarries under shell fire as a routine matter. An Engineer forestry company was decimated while cutting bridge timber on the Siegfried line. Oneof the more spectacular feats of the Army Engineers in obtaining construction materials was the operation of the Hadir Steel Works during the fall and winter o f 1944.

Jan 1, 1946

By THOMAS J. CLIFFORD

IN 1926, finer grinding began to be a feature of the milling practice of the Southeast Missouri lead district. Nothing since the adoption of flotation has caused greater changes and greater improvement in results. The trend toward finer grinding, with the consequent discarding of tailing at finer sizes, and consequent lower assays in lead, continued to progress until 1931, when the abnormally low price of lead brought a halt: that is, the better metallurgical results obtained would not offset the increased costs due to higher power and necessary maintenance. Since 1931 a slight tendency toward the discard of coarser tailing has taken place. , In 1926, larger rod mills i.12 ft. 1 in. by 6 ft. 6 in.) than any previously used in the district were installed in cue plant, and a new primary crushing plant, of greater capacity was built. This combination demonstrated immediately the better metallurgical results obtainable by finer grinding and all the mills now running have adopted the practice.

Jan 1, 1934

By J. E. Norton

Production statistics show that during the period of emergence from the depression the coal industry was becoming increasingly cognizant of the economic and competitive necessity for mechanizing. About 1935 many of its leaders were becoming aware also of the alarming scarcity of men properly trained to cope with the new problems of mechanization. In order to get a factual statement of this problem, a special AIME Coal Division Committee was requested to survey the condition. Its investigation disclosed that graduates of mining schools going into coal mining numbered 16 in 1937 and 15 in 1938. With this as a background, Pittsburgh Coal Co. foresaw that a comprehensive program was necessary if it was to enlist the services of trained technical men, who were an indispensable part of a mechanization program. The purpose of this paper is to review the program set up, to comment on the successes and failures and to outline the future course of action. Summer Work An inescapable conclusion from the mechanization statistics was that the opportunities in coal mining were good. Not only was there a void in technical skill to fill from past years, but the accelerating rate of mechanization indicated an increasing demand for technically trained men for the future. The remedy lay primarily in presenting facts con cerning the coal industry to the undergraduate engineers before they made their professional occupational choice. Based on this idea, one of the key points in the program was summer vacation work for the undergraduate, which, through the inducement of summer earnings, brought men into the mines to take a look at the prospects. This was more successful than statistics indicate because the war scrambled badly the orderly working of the program, but it could not obscure the value of a summer work program. A decided advantage was that it gave the company a preview of the graduate. An observation on this part of the program is that it is extremely hard to gauge lower classmen, and we found it wise to give them the benefit of the doubt, as the last two years in college bring about surprisingly rapid development in some men. We could readily single out the men at the opposite ends of the scale of competence. Comprehensive Training Program Having adopted summer work as a means of interesting undergraduates, the Location Weeks Introduction............................... I Underground mining operations............... 27 Coal preparation............................ 24 Inspection—safety, mech., prep............... 31 Mine engineering and survey................. 16 Industrial relations.......................... 12 Operating staff—costs, time study............. 8 Miscellaneous............................... I Total.................................... 120 problem of attracting graduates was met by establishing a training program that covered approximately 120 weeks and

Jan 1, 1949

By M. H. Waxman, L. J. M. Smits

A simple physical model was used to develop an equation that relates the electrical conductivity of a water-saturatedshaly sand to the water conductivity and the cation-exchange capacity per unit pore volume of the rock. This equation fits both the experimental data of Hill and Milburn and data obtained recently on selected shaly sands with a wide range of cation-exchange capacities. This model was extended to cases where both oil and water are present in the shaly sand. This results in an additional expression, relating the resistivity ratio to water saturation, water conductivity and cation-exchange capacity per unit pore volume. The effect of shale content on the resistivity index - water saturation function is demonstrated by several numerical examples. INTRODUCTION A principal aim of well logging is to provide quantitative information concerning porosity and oil saturation of the permeable formations penetrated by the borehole. For clean sands, the relationships between measured physical quantities and porosity or saturation are well known. However, the presence of clay minerals greatly complicates log interpretation, particularly the electrical resistivity and SP logs, and considerably affects evaluation of hydrocarbon-bearing formations. The conductance and electrochemical behavior of shaly sands and their relation to log interpretation have been studied by many workers. wylliel and Lunch2 reviewed this work in some detail. Virtually all laboratory measurements of electrical resistivity and electrochemical potential of shaly sands published to date are the work of Hill and Milburn.3 Their measurements were made on about 300 cores covering a large variety of sedimentary rocks, and a wide range of equilibrating NaCl solution concentrations. Hill and Milburn described their conductivity data by an empirical equation in which the shaly sand conductivity Co was expressed as a function of the solution conductivity C and two parameters b and F01 . The quantity b was shown to be a measure of the effective clay content of the rock, being approximately proportional to the cation-exchange capacity of the rock divided by its pore volume. The latter ratio is designated as 9, in this paper and has the dimensions meq/ml or equiv/liter. Qv is identical with the term representing the concentration of fixed charges in the Meyer-Sieved and Teorel15 theory of permselective membrane behavior. F01 is a formation resistivity factor referred to a hypothetical equilibrating solution resistivity of 0.01 ohm m at 25C,* where clay effects presumably are minimized. F01 was correlated to porosity by an Archie-type equation.6 The Hill-Milburn equation describes their data with a standard deviation of approximately 1 percent and a maximum deviation of + 10 percent. Shaly sands behave as permselective cation-exchange membranes, their electrochemical efficiencies increasing with increasing clay content. The electrochemical potential data of Hill and Milburn were expressed graphically, and demonstrate that the membrane efficiency (or cation transport number) of these sands is a function only of the b value (i.e., Qv) and the respective salt concentrations of the two solutions forming the liquid junction in the sand. The diffusion potentials are not dependent on F01 or any parameter relating to the porosity or pore geometry of the rock. The Hill-Milburn resistivity equation correctly predicts a decreasing sand conductivity Co with decreasing solution conductivity C?. However, at some low value of C,, the calculated Co-C, function goes through a minimum; with further decrease in C?, the predicted sand conductivity increases sharply. As pointed out by Hill and Milburn, an increasing value of Co with decreasing C, is physically meaningless. Since this occurs below the range of practical values of C,, the usefulness of the empirical equation is not affected when

Jan 1, 1969

W. 0. HOTCHKISS, * Madison, Wis.-It was fortunate, in a way, that this subject of income taxation came up during the war when the government could appeal, on the basis of patriotism, to men of large, business experience to undertake the work of formulating this matter and practically donate their services. At any other time the government would have been unable to secure the necessary number of men of like ability. There is one thing that must not be forgotten. In all cases, except the very largest and most important, the application of this income tax law to a mine is going to be made by clerks whose salaries are fixed by a Congress that appropriated a half billion of dollars for a war purpose and provided that $4000 should be the highest salary paid in the adminis-tration of that great sum. The Congress of the United States unfor-tunately seems almost entirely unaware of the fact that men of ability and experience are worth money and must be paid adequately if proper public service is to be secured. While the formulation of the broad plans for administering the law have been in the hands of. men of unusual ability, we have the future to guard, and, if possible, the mining industry should see to it that the Internal Revenue Department is permitted by Congress to pay salaries that will enable it to secure men of the ability and experience necessary to insure proper consideration of the industry. Another fact to which I would call attention is the difference between the business and the economic, or economists', points of view as to what a mine is. The economists have properly, from their point of view, classed a mine as a wasting asset, but the average metal mine is not a wasting asset if it is a real mine. The economists are correct in a broad sense in that every ton of ore taken out diminishes the orebody by that amount. When it comes to the consideration of an individual mine from the business standpoint, the future of that mine rests on unfore-seeable events-the discovery of new orebodies or the development of old bodies beyond the point of probable expectations. Every going mine must develop new ore each year to replace that extracted, and, .during all but the last one or two years of its activity, actually does so. Instead of being a "wasting asset" such a mine, from the practical stand-point which must control valuation, is an "increasing asset." From

Jan 12, 1919

By H. R. Stahl

The ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classi- fiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9½-in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 52¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1¾ in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges

Jan 1, 1947

By H. R. Stahl

The ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classi- fiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9½-in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 52¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1¾ in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges

Jan 1, 1947

By A. L. Benham, W. E. Dowden, W. J. Kunzman

The mechanism involved in creating a miscible fluid displacement of typical reservoir fluids through porous media by light hydrocarbon mixtures usually involves a number of mixing and separation stages in the contact area. This mechanism has been illustrated on ternary diagrams for miscible displacement of reservoir fluid by rich hydrocarbon gases. A relatively simple method has been devised for calculating the approximate conditions for a miscible displacement of reservoir fluid by rich, light hydrocarbon gases or by LPG mixtures. Miscibility is favored by increased pressures, decreased temperatures, light reservoir fluids and light hydrocarbon-displacing fluids rich in the heavier components. The conditions for miscible displacements of five typical reservoir fluids by various light hydrocarbon mixtures were determined for a range of temperatures from 70" to 260°F and pressures from 1,000 to 3,000 psia. A correlation of these conditions was obtained using the variables of temperature, pressure, C,+ molecular weight of the reservoir fluid, C,+ molecular weight of the displacing fluid, and mol per cent methane in the displacing fluid. This correlation has been applied to data appearing in the literature with very good success. A partial check of the correlation has been made using a step-wise procedure with a windowed PVT cell. INTRODUCTION The term, "miscible fluid displacement", may be defined as any oil-recovery displacement process where there is an absence of a phase boundary or interface between the displaced and displacing fluids. A water flood would not be a miscible fluid displacement, although cycling in a condensate reservoir would be. Another example is displacement of oil by gasoline. Not so obvious, however, are the conditions under which fluids (such as propane, mixtures of propane and methane, or other similar systems) will give a miscible fluid displacement of oil. There are four standard miscible-fluid-displacement processes being used for the recovery of oil from an "nderground reservoir—(1) high-pressure dry-gas miscible displacement, (2) rich-gas miscible displacement, (3) miscible slug using a slug of LPG followed by a lean dry gas under miscible conditions, and (4) gas driven-slug process using a slug of LPG followed by a lean dry gas under immiscible conditions. The first problem faced by the engineer designing a miscible displacement process is to determine the conditions for miscibility. A number of papers have included discussions of the process of obtaining miscibility in these processes.1-8 However, methods for calculating the conditions for miscibility have not been published. This paper includes a method for calculating the conditions for a miscible displacement of reservoir fluid by a rich gas (LPG diluted with methane or natural gas). In this paper, a rich-gas miscible displacement process is defined as an oil-recovery process in the reservoir. The cost of a rich-gas miscible displacement will be decreased by diluting the LPG with methane or natural gas as much as possible. Therefore, it is important to be able to predict the maximum dilution for miscibility. MECHANISMS The mechanisms for obtaining miscibility between a displacing mixture of light hydrocarbons and displaced reservoir fluid often involve a number of displacing and mixing stages. As stated previously, the cost of a rich-gas miscible displacement is decreased by diluting available LPG with natural gas. The problem is to predict the maximum dilution allowed while maintaining miscibility. To get a picture of the displacing and mixing stages, it is helpful to consider these complex hydrocarbon mixtures as pseu do-ternary systems. Graphical representation of a complex system as a pseu do-ternary system can be thermodynamically rigorous if enough variables are used to describe the character of each pseudo-component in one of the phases. However, even if the characterization of each pseudo-component is not complete, pseudo-ternary representation does serve to illustrate the mechanism for obtaining miscibility and can be used to make some general conclusions concerning the conditions for obtaining miscibility. A phase diagram for the ternary system, methane-

By C. Richard Tinsley

INTRODUCTION Project financing has been defined by various authors in this book. It is founded on reliance upon the project's own future cash flows and secondarily on the collateral value of the asset base developed. It is chiefly provided by the banking community who, after an assessment of the risks involved (See Chapter 9) analyse the company's presentation (See Chapter 10) in order to structure a financing package often at a leverage of up to 80% debt. This paper describes the various support and structuring techniques used to delimit and abate the risk components perceived from the banks' experience on project development especially for the period before cash flow is generated (pre completion). ADVANTAGES The advantages of project financing extend beyond the offloading of risks to banks. Among the advantages are the following: 1. Longer loan maturity than conventional, unsecured financing; 2. Loan disbursement and repayment tailored to specific mine; 3. Ability of a joint venture without a "track record" to raise financing; 4. Obtain financing where further direct borrowing (corporate credit) limited by existing indentures; 5. Possibility of arranging finance off-balance sheets; 6. Leverage return on equity; 7. Obtain tax savings with certain project financing structures; and 8. Obtain flexible loan repayment conditions. It can also be said that from the point of view of the company, project financing has certain disadvantages which can be summarised as follows: 1. Perceived higher cost (risk premium) compared with straight corporate credit; 2. More documentation; and 3. Need to negotiate risk-sharing aspects. The main attraction of project financing is the ability to pass certain risks on to the lenders within a flexibly funded transaction. (For a more detailed description of the specific risks see the author's paper at the beginning of Chapter 9. The same risk system is followed here.) The typical project financing has corporate support prior to completion and will usually carefully control the resultant cashflow after completion to ensure the bank does not unnecessarily assume further risks of an equity nature. WITHIN THE COMPANY'S CONTROL Operating Risk This is broken into three interrelated segments for ease of description. Technical Component: This must be specifically addressed if new technology or unproven adaptations are to be used. The banks will have scrutinized the sampling and bulk testing work, perhaps grilling the geological, mineral processing, metallurgical, and mining engineering staff or consultants directly. A number of supports are available such as: TECHNOLOGY GUARANTEE: Either the company itself or the process developer will guarantee that the technology will work for a period of, say, six months to two years after startup. If not, then financial penalties will apply although these are rarely sufficient to repay the loan. Many process developers are weak financially and may have little substance to back such a guarantee.

Jan 1, 1985

By Arthur F. Wendt

The following experiments and researches were originally conducted by Dr. Heinrich Rcessler, chief of the German Gold and Silver Parting Establishment at Frankfort-on-the-Main, for the sole purpose of abating the nuisance created by the discharge into the air of the sulphurous and sulphuric acids generated in the process of parting bullion by sulphuric acid. The results achieved have, however, an important bearing not only on this process, but are of value in the manufacture of sulphuric acid and sulphate of copper from sulphurous gases derived from any source. It has now been in successful operation for a term of years at Dr. Roessler's own works, and has been lately introduced with satisfactory results at the royal mints of Kremnitz and Munich, and the well-known establishment of Johnson Mathey & Co., of London.

Jan 1, 1884

By Dorsey A. Lyon, Robert M. Keeney

Page I. Introduction..........234 I1. Chemistry oF Copper Smelting...235 1. Native Copper Ores.......235 2. Oxide and Carbonate Ores....235 3. Sulphide Ores.......236 (a) Elimination of sulphur ...236 III. Reverberatory Copper Smelting...237 IV. Substitution of the Electric Furnace for the Reverberatory Furnace..................... 238 V. Smelting of Fine Michigan Native-copper Concentrates in the Electric Furnace.................. 239 1. Conclusions.................240 VI. Proposed Process for Electric melting of Fine Native-copper Concentrates.................. 241 VII. OrdINary Copper Blast Furnace 'Smelting......... 245 1. Prerequisites.................. 245 2. Losses .................... 247 VIII. Experimental Data on the Electric Smelting of Raw Sulphide. Oxidized and Carbonate Ores............. 248 1. Vattier's experiment................ 248 2. Wolkoff's experiments................ 249 3. Experiments of Stephan.............. 250 (a) Conclusions of Stephan ............ 251 IX. Smelting of Sulphide Ores in the Electric Furnace...... 251 1. Ores Treated.................. 252 2. Conclusions................... 253 X. ELectric Furnace vs. the Reverberatory Furnace and Blast Furnace as a Melting Agent.............. 253 XI. Smelting of Sulphide Ores without Roasting or Partial Pyritic Smelting............254 XII. The Electric Blast Furnace vs. the Copper Blast Furnace for Partial Pyritic Smelting.......259 1. Metallurgical conditions......259 2. Mechanical considerations......259 3. Comparison of costs.......260 (a) General considerations .....260 (b) Cost of plant........260 (c) Amount of electrical energy...260 (d) Cost of smelting.......261 (e) Cost of electrodes........262 XIII. The Use of the Electric Furnace in the Smelting of PyRITIc ORES : 262 XIV. Summary...................... 264

Jan 1, 1914

By B. W. Adams, R. W. Shilling

9.4-1. Basic principles. DESCRIPTION AND BASIC FUNCTIONS. The concept of inclined skip haulage is not new. The basic idea has been in use at least 400 years. The system is essentially a steeply inclined railway utilizing a hoist to pull the skips to the top or intermediate positions. Inclined skip haulage is often justified where high lifts would require long hauls for other haulage systems. The basic system types are as follows: 1. Single skip, single drum. This system is a single car pulled by a simple hoist system. 2. Balanced skip, single drum. A system utilizing two cars (skips on cables)--one overwound, one underwound-on a single drum. The dead weight of one skip and cable balances the dead weight of the other. As one skip ascends the other descends between two fixed points. 3. Balanced skip, double drum. This system is an elaboration of system No. 2, except the drums may be disengaged from one another to permit the skips to service various loading and dumping points. The preceding are major classifications subject to numerous variations. These variations may be in the skipway, skip design, loading methods, or unloading methods. A few examples follow: 1. The skipway may be standard or special railroad, an overhead monorail or cable, or a ramp for rubber tired vehicles. 2. The skip, per se, may be of varying dumping arrangements (side, bottom, etc.) or could be the box of the vehicle hauling to the skip. 3. Loading may be accomplished directly from the service unit to skip, through an intermediate loading device (e.g., a pocket), or into bins which feed the skip. Loading may be at more than one point. 4. Unloading of the skip can be simple or complex as required. Dumping may be to the haulage unit, to bins and feeders, or to a crusher and conveyor system. Dumping may take place at more than one point.

Jan 1, 1968

By E. J. KENNEDY

FEBRUARY 15-18 will be the outstanding dates of the month for members of the A. I. M. E., for then the 141st Meeting of the Institute is to be held in the Engineering Societies Building, at New York. What with 41 technical sessions, the Annual Business Meeting at 4 o'clock Tuesday afternoon,, two sessions of the Section and Division delegates, minor committee meetings, and the many luncheons and dinners, the Dinner-Smoker, Informal Dance, President's Reception and the Dinner-Dance, the opportunity will be limited to do- more-than cast sheep's eyes at New York's other multitudinous attrac¬tions until the meeting is over. The technical program is diverse but well organized. The sessions are almost equally divided among the four days, with ten on Monday, Tuesday, and Wednesday, and 11 on Thursday. The meeting opens Monday morning with registration. Be sure to attend to this detail. Failure to do so may have its repercussions at the meeting and throughout the year.

Jan 1, 1932

By Louis B. Slichter

Prospecting is certainly the world's biggest and best gambling business. It is a game where the chips cost many thousands and where many millions, even billions, can be won. An attractive feature of this gamble is the fact that the players are free to rig the odds as favorably as possible. Only the limited bounty of nature, the restrictions of the laws of the land, the competition from other players, the limited sagacity of the player himself- only these, and other factors, restrict the possibilities for large winnings. Today probably about half the land surface of the earth remains to be searched for signs of ore visible at the surface. It is fortunate that so much land still remains for exploration by relatively economical methods. Looking to the future, it is a good guess that the costs of finding ore will increase in response to increasing technical difficulties. To continue to achieve profits from prospecting, it will become necessary to analyze the business more skillfully, in a more and more sophisticated manner. Whenever feasible, qualitative concepts must be replaced by their quantitative equivalents, improvements, and extensions.

Jan 6, 1960

By N. Brown, R. Kossowsky

Plain carbon steels with 0.48 and 0.95 pct C were quenched and tempered at 705°C to produce carbide dispersions with spacings on the order of 1 p. The morphology of the structure consisted of a carbide-dislocation network. The strengthening due to the dispersion was found to vary linearly with M-½ where M is the mean free-ferrite path determined by the entire network. No preyield microstrain preceded the upper yield point. After prestraining, the lowest stress at which dislocation movement could be detected was 104 psi; this frictional stress was independent of the dispersion and prestrains up to 6.5 pct. The Cottrell-Petch equation for grain-size strengthening was used to discuss the dispersion strengthening in this investigation. The results support an impurity mechanism for the upper yield point rather than one based on the Johns ton- Gilman theory. IT was pointed out by Gensamerl that the mean free path in the matrix is the important variable which controls the degree of dispersion strengthening. Gensamer's data on steels showed a linear relationship between the yield point and the logarithm of the mean free-ferrite path. The first theory was by Orowan,2 who suggested the mechanism of dislocations bowing between particles, with the resulting relationship that where a is the yield point, P is the distance between particles, and G is the shear modulus. The Orowan equation applies to that range of dispersion where P is large compared to the particle size and the particles are not coherent, so that the matrix is essentially free of internal stresses. As was pointed out by Orowan, there are different degrees of dispersion which, in turn, will influence the strength-controlling mechanism. However, in this investigation, we wish to confine ourselves to the region of coarse dispersion, where the Orowan mechanism should, intuitively, be applicable. It was soon evident that the data, which existed at about the time that the Orowan theory was proposed, did not agree with the Orowan equation in that the actual strengthening was always greater than the theoretical predictions. Thus, Fisher, Hart, and pry3 modified the Orowan theory by suggesting that the Orowan process took place in the microstrain region preceding macroscopic yielding and the subsequent, rapid work hardening in the form of residual dislocation loops around the particles largely determined the observed macroscopic yield point. The F-H-P theory stated that the increment of strengthening due to the work-hardening mechanism was proportional to f3/2 where f is the volume fraction of the precipitate. F-H-P used data by Shaw, Shepard, Starr, and Dorn4 on A1 3-5 pct Cu to support their theory. Roberts, Carruthers, and Averbach5 were the first to make a microstrain study of dispersion strengthening, and they found that for steel the Gensamer relationship was obeyed. Hayman and Nutting6 suggested that in the case of tempered steel 1) the ferrite grain boundary was the primary obstacle and 2) the carbide particles simply formed part of the grain boundary obstacles. They found that the strength varied as G"" where G is the ferrite grain size. Turkalo and LOW' determined the structure of quenched and tempered plain carbon steel using a replica technique; they concluded that the carbide particles did not necessarily lie in the ferrite grain boundaries. When they defined the mean free-ferrite path as being determined by both particles and the ferrite path boundaries, their data obeyed the Gensamer relationship. Meiklejohn and skoda8 showed that the strengthening from iron particles in mercury was a function of the particle size and the distance between particles. Dew-Hughes9 explained the Meiklejohn and Skoda results by the following theory: 1) grown-in dislocations which surrounded the particles were produced by the thermal stresses during the time the material was cooled to the testing temperature, and 2) the observed strengthening was associated with the cutting of the grown-in dislocations by the glide dislocations. Ansell and Lenel10 proposed a theory in which the glide dislocations pile-up or surround the particle until the number of dislocations in the pile-up is sufficient to yield or fracture the particle. The resulting theory says that the yield point varies as p-1/2, where P is the distance between particles. The Ansell-Lenel theory is almost identical to the

Jan 1, 1965

By Hiroshi Oikawa, A. G. Guy

Recent experimental evidence has shown that it is often incorrect to neglect the reactions occurring at an interface with respect to the diffusion reactions. By introducing reaction-rate constants and k for the transfer of components 1 and 2 between the a and b phases, a phenomenological description has been devised for the coupled processes of diffusion and in-terfacial reaction. An illustrative example has been analyzed with the aid of a suitable computer program. The results indicate that for kab values on the order of 10'1 cm per sec and Ð values of about 10¯10 sq cm per sec, the interfacial reactions are significant during the first 10 2 to l0 6 sec of a diffusion experiment. Among the observable effects of the interfacial reactions in this case appear to be the burying Kirkendall markers and an anomaly in the initial shifting of these markers. THE study of diffusion between two phases is especially important because of its direct connection to phase transformations. For example, the transformation of austenite to ferrite involves diffusion in the a and ý phases and also an interfacial reaction (trans formation) at the a/? interface. If ferrite and aus-tenite are the two members in a diffusion couple, the same two reactions occur during the diffusion process. The numerical values obtained for the diffusion coefficients and interfacial-reaction constants from diffusion experiments can then be employed to predict phase-transformation behavior. Refinement of the calculations of phase transformation is also suggested by the present method for treating two-phase diffusion. In the recent paper by Nolfi et al.' only the solute com ponent is considered in the interfacial reaction accompanying a phase transformation. The present analysis demonstrates that both components must be considered. It is generally recognized that reactions of some kind must occur at the interface in a two-phase diffusion couple, but usually it is assumed that the interface reaction occurs so rapidly that its effect on the overall process is unobservable because the slower diffusion process determines the kinetics of the process. However, Seith and Heumann 2 pointed out that effects of the interfacial reaction should always occur in the early stages of diffusion, and recently Eifert et al. 3 have shown that interfacial reactions influence the composition and motion of the interface in a/ß Al-Cu diffusion couples during the entire course of prolonged, high-temperature treatments. A general procedure for handling the combined processes of interfacial reaction and diffusion in a binary, two-phase system is to introduce kinetic coefficients for the interface reactions and to develop the system of equations governing the interlinked processes of diffusion and interface reaction. The resulting equations, although not amenable to solution in closed form, can be usefully manipulated by a digital computer. INTERFACIAL REACTIONS IN TWO-PHASE DIFFUSION Consider the general case of diffusion between two solid solutions, a and ß, which are adjacent phases in a binary system, Fig. 1. Two semiinfinite bars having compositions c1 and c0ß are jointed at x = 0. If concentrations are expressed in volume fraction,4

Jan 1, 1970