Search Documents

By J. T. Norton, Pekka Rautala

The phases and equilibria in the W-Co-C system have been studied by X-ray diffraction methods, metallographic technique, and thermal analysis. In addition to the 7 phase, two double carbides, called 8 and have been revealed. The compositions correspond to CO3 W6C2 and Co3-W10C4. The reactions leading to these phases have been explained and tentative diagrams of stable and metastable equilibria proposed. The basic reactions in sintering cobalt cemented tungsten carbides are discussed. THE W-Co-C system is of fundamental importance in practical carbide manufacturing as well as for the understanding of the sintering mechanism. Surprisingly little is known about this system, for the probable reason that all the important alloys are of two-phase structure and that the diagram Co-WC has been treated as a quasi-binary. This obviously is incorrect, because WC decomposes before melting. One ternary phase, 7, of composition Co3W3C has long been known. It was first studied by Adelskold, Sundelin, and Westgren,1 although the isomorphous iron-tungsten carbide was known earlier. There have been in the literature several reports of two 7 phases.' " Also the 7 phase has been considered unstable by Takeda4 and Westgren.1 The Co-WC diagram has been studied by Wyman and Kelley5 and a quasi-binary diagram has been published by Sandford and Trent.2 Takeda has published a tentative Co-W-C diagram, considering both metastable and stable equilibria. However, the lines of two-fold saturation are shown only partially and it seems impossible to complete the diagram without violating the phase theory. Therefore it seemed desirable to examine the system in more detail. Experimental Procedure The alloys used in the present investigation were made of powders of tungsten, tungsten monocarbide, cobalt, and carbon and were of the grade used in manufacture of commercial cemented carbides. The powders were ground and mixed in small stainless steel ball mills, using balls of the same material. Benzene was used as a dispersing agent. The mixing period was 1 hr, since this was shown to give suffi- ciently good mixing of the powders without too great a contamination from the mill. After ball milling, the specimens were pressed in cylindrical or rectangular dies. No paraffin or other lubricant was used and the small compacts had sufficient green strength to be handled without difficulty. Several sintering furnaces were employed. The most satisfactory arrangement was a vacuum furnace based on the Arsem principle which employed a graphite helix as the resistance heating element. Specimens were placed on graphite stands and there was generally a slight carburization or decarburiza-tion of the specimen surface, depending on the carbon content of the alloy. The evaporation of the cobalt at a sintering temperature of 1400°C was not significant, but became severe at 1500°C and higher. The sintering time was 1 hr at 2000°C and 2 to 4 hr at lower temperatures. It was not possible to quench the specimens, but the cooling rates were rather fast, greater than 300°C in the first minute. In the system under investigation, the reactions are sluggish, and it is believed that the high temperature structures are satisfactorily retained. The principal method of investigating the sintered specimens was X-ray diffraction by the Norelco recording spectrometer. Approximate determinations of the phase boundaries were made by the disappearing phase method. Ternary Phases To study the phase formation in W-Co-C system, a series of specimens was sintered at 1400°C. In this experiment two ternary phases, called here ? and k were formed in addition to the well-known 7 phase. The 7 phase, which has been completely described by Westgren: showed a range of homogeneity from 7 to 20 pct C and from 38 to 48 pct Co. At 1400°C the 7 phase was found to be in equilibrium with monotungsten carbide, 8, tungsten, 8, #?, and liquid. The boundaries toward #? and liquid were difficult to determine and appeared to be very temperature sensitive. The other boundaries are believed to be well fixed. The homogeneity range of 7, as measured in this work, is considerably smaller than the one

Jan 1, 1953

By Frank C. Smith

The following article covers the history of a metallurgical campaign, commenced in March, 1905, at the mines of the Socorro Bold Co., in the so-called desert region of Yuma county, Arizona. The results obtained were simply a function of necessity, as will be seen from the description of the local economic conditions and the character of the ores treated. The mines and mill of the Socorro Gold Co. are located near the small village of Harrisburg, about 60 miles from Congress Junction, Ariz., which, at the time this work was undertaken, was the nearest railroad station, and from which all supplies were brought by wagon through the desert, at a cost varying from $10 to $15 per ton in addition to the railroad freights. Wood, the only available fuel, cost $7 per cord. Water for all purposes was pumped to the plant from a well in the valley about 4 miles away. Under the Arizona law, a working-shift is 8 hr. Wages were $6 per day for foremen and mill-men, $4 per day for blacksmiths and engineers, $3.50 per day for miners, and $3 per day for shovelers and trammers. The ore consisted of quartz, in which, above the 250-ft. level, the iron-minerale were largely oxidized and some free gold was visible; below that level few traces of oxidation occurred, and pyrite constituted the principal mineralizer in the quartz, together with occasional pockets of galena and a few eccentric specks of covellite. The 20-stamp mill was equipped with plates for amalgamation, and three Standard tables for concentration. The tails from the tables mere elevated by a centrifugal pump to a launder, by which they were conveyed to a 60-ton cyanide-mill for further treatment. The cyanide-mill was erected at so great a distance from the stamp-mill that a separate crew of workers and a separate power-plant were necessary. No arrangement had been made for the treatment of the concen-

Jan 1, 1907

By John Vanderwilt

THE value of molybdenum as a ferroalloy has been known for many years. For a long time, however, the metal was used only on a small scale in the iron industries, because the known source of supply appeared inadequate and the cost to the consumer was not stabilized. The world's production of molybdenum prior to 1914 was only a few thousand pounds per year and even during the war period annual production was only about 800,000 lb. Production during 1929 and 1930, however, was over 4,000,000 lb. per year and that of 1931 promises to be of the same order of magnitude. This remarkable increase in production is due primarily to the development of a large molybdenite deposit at Climax, Lake County, Colo., which has accounted for 80 per cent of the world's production of molybdenum during the past two years. Based on conservative esti-mates, the deposit at Climax has the capacity to maintain its 1929 and 1930 rate of production for 100 years or more. The production of molybdenum ores has been established on a new basis-in recent years as compared with the period during and before the world war. During the earlier period, production came from small deposits and the cost to the consumer fluctuated. At present, production comes from a few large deposits and the price is not only lower but also fairly constant. In recent years the price of molybdenum has consistently dropped as consumption increased. The present price is $0.95 per pound of molybdenum in ferromolybdenum and $0.80 for molybdenum in calcium molybdate. Before and during most of the war, Australia, Norway, and a few other foreign countries were the chief producers, while at present the United States is producing over 90 per cent of the world's production. With molybdenum available at a moderate cost, the steel industry has been adopting more and more the use of molybdenum as an alloy addition. A relatively small demand for molybdenum exists in the chemical and electrical industries, but the recent large increase in con-sumption has in large part been by the iron and steel industries, which

Jan 1, 1932

By K. E. N. Hanney

INTRODUCTION Slurry systems and mechanical conveying, represent the main methods of transporting solids from one area of a mineral processing plant to another. A well-designed slurry handling system can assist in lowering plant capital costs by reducing building size, simplifying plant layout and reducing operating costs by lowering maintenance and labour costs. This Paper has been prepared with the object of providing a practical approach to designing slurry systems. SLURRY CHARACTERISTICS Slurry is a mixture of crushed or ground rock mixed with water or a chemical solution, and can flow under several different conditions: (a) As a homogeneous suspension; (b) As a heterogeneous suspension; (c) With a moving bed (saltation); (d) With a stationary bed. Homogeneous flow takes place when the solids are uniformly distributed throughout a pipe and when particle sizes are smaller than 325 mesh. Heterogeneous is the most common slurry suspension. In this system, there is a gradual increase in concentration of solid particles towards the bottom of a pipe. There is a fairly wide range of velocities that fall within this system. In moving bed systems, the coarse particles settle out and bounce along the bottom of a pipe. Operating under these conditions tends to minimize wear and power requirements, but because this system operates within narrow velocity limits, pipelines frequently plug. Stationary bed conditions exist when coarse material has settled in the bottom of the pipe restricting the available area. These conditions should be avoided. DESIGNING A SLURRY SYSTEM Slurry can be transported either by pumping through a pipeline or by developing a gravity head and flowing through a pipe or along a launder. When considering any slurry system, whether for the design of a new plant or to make modifications to an existing operating plant, design criteria are required. The design criteria provide the information for calculating the material balance and sizing the equipment. The quantities on the material balance can then be assigned to the flowsheet for reference. The equipment can then be laid

Jan 1, 1982

By H. A. Wheeler

. Page History.................................533 Location .........:.....................536 Geology...............................539 Description of the Eastern Field ... :..................543 Description of the Western Field .........,...........546 Quality of the Oil ................ ,........549 The Oil Sands .,.............................549 Drilling Features'........................., . 551 Well Density...........,.'...............:. 552 Plant Equipment.......................:.'., .554 Market Features..........................555 Production Prices.........,...................557 Royalties and Rentals.........................558 Cost of Oil Leases............................'.558 Operating Expenses..........................559 Operating 'Profits...........................559 Gas Developments ........................560 Gas-Gasoline production ... :....................561 Statistics.......562 History Illinois has SO recently attained the third place in the oil production of the United States that few realize its great importance, or are aware of its highly profitable character. Since 1907 Illinois has furnished about 15 per cent. of the United States output and about 10 per cent, of the world's production. The value of the output in 1913 is estimated at $307000,000, of which about $20,000,000 is profit. The present prosperity dates from 1905, but efforts have been made since 1865 to develop production and geologists have been very sanguine as to its future for over 25 years. Had the oil operators been as confident as the geologists, the field would have been opened at least 30 years earlier. For the rich Eastern Illinois oil field is located along the La Salle anticline, that was mapped 46 years ago by Professor Worthen in the

Jan 1, 1915

By LESTER H. WOOLSEY

IT IS doubtful whether anything new can be said upon this subject and, therefore, it is with considerable hesitation that l prepare this paper. On account of my recent connection with the Department of State as its law- officer, perhaps I will be pardoned if I discuss this subject briefly from the point of view of that branch of the Government. , I cannot, of course, speak for that department, since I have-no connection with it at-present, but it may be helpful if I set down certain* of the factors which in my opinion and from my experience have a bearing on this international problem. With oil-burning ships, motor vessels, motor vehicles, airplanes-all consuming, astonishing quantities of petroleum or petroleum products; with the United States having within its borders only 12 per cent. of the petroleum resources of the world, and consuming about 70 per cent. of the world's output; with the more enterprising nations wide awake to the necessity ; of obtaining and preserving as large a share as possible of the oil resources extant ; the 'problem is peculiarly and in a, very practical sense an international one.

Jan 1, 1921

By Russell Webster

In having maintained production for more than 40 years Arizona's Magma mine is unique in a mineral district that includes several major copper mines. Other past and present producers in this area are Miami and Inspiration at Miami, the Old Dominion in Globe, the Ray mine in Ray, and to the south the new San Manuel mine near Tucson. Magma's production of copper, silver, gold, and some zinc has come from nearly parallel east-west striking mineralized faults, one called the Main or Magma vein and the other the Koerner vein, about 1100 ft to the south. This vein system has been prospected and partially mined for some 9000 ft horizontally and 4800 ft vertically. In ascending order from the deepest exploration level, the Main vein cuts Pre-Cambrian schist, Pre-Cambrian Apache Group, Post-Devonian diabase, and Devonian, Mississippian, and Pennsylvania limestones. Until 1950 very little ore was obtained from replacement mineralization.

Jan 10, 1958

By M. E. Wadsworth, I. B. Cutler

Coprecipitation of anionic and cationic polyelectrolytes has been applied to floccula-tion of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves. DISPERSION of colloids has been of interest to surface chemists for many years. Flocculation studies have been employed to evaluate the limits of colloid stability. In water suspensions, colloids become unstable and flocculate when the ( potential, the potential of the kinetic solvation sheath, falls to a value at which van der Waals forces may act to draw the particles together. This may happen through an adjustment of the pH of the suspension or by addition of a salt. Optimum conditions for rapid formation of large flocs are found in the region of minimum ( potential. In addition to these well known considerations, colloids in water suspensions are known to be flocculated by certain large organic macromolecules. These polyelectrolytes in some cases minimize the i potential and in other instances increase the attractive forces by supplying sites for hydrogen bonding.' Use of organic polyelectrolytes in flocculation of mineral colloids has increased rapidly in recent years. These materials are now recognized as indispensable aids to fluid-solid separations in many extractive metallurgical operations. They have been found to increase both the settling rate in thickeners and the filtration rate of filters. In the elucidation of the characteristics of these organic reagents as floc-culants in this laboratory, it was discovered that interaction of certain polyelectrolytes had a surprisingly good effect on flocculation of mineral colloids. Experimental Procedure: The anionic flocculants used in this study were Lytron 886 and 887, produced by Monsanto Chemical Co. Both reagents are copolymers of vinyl acetate and maleic anhydride. Lime is added to Lytron 886, whereas Lytron 887 is all organic. These reagents possess two carboxyl groups for each acetate group and are therefore anionic in character. The cationic reagents used were the Peter Cooper Co. 1-X and 2-X glues. The structures are not definitely known, but the re- agents are amines and are cationic in character. The glues were prepared in the chrome-alum form. Both types of reagents may be classified as polyelectrolytes in that they are high molecular weight polymers and ionize in water. All data presented are in terms of sedimentation rate, measured in 250-ml glass-stoppered graduated cylinders. With suitable precautions such measurements are fairly reproducible and provide a sensitive means for selecting important parameters such as pH, reagent concentration, and floc size and density.2 Agitation was standardized with five complete end over end cycles of the suspensions in the stoppered graduated cylinders.

Jan 1, 1957

By W. B. Morrison

Anderson, King, and Spreadborough present detailed evidence to show what ~aldwin~' has already pointed out, that, over a relatively small grain-size range (Ad"1/2 ^ 10 mm-'I2, d is average grain diameter), yield point data can fit a number of relationships. Part of the difficulty in obtaining data which reflect only the effect of change in grain size on yielding arises from the fact that in varying the grain size, even though great care is taken, other structural changes are almost certain to occur. In iron alloys, these changes may consist of variations in subgrain size, grain boundary ledge density, and degree of carbon and nitrogen segregation at grain boundaries, all of which are difficult to detect and which may affect yielding, primarily through their effect on dislocation generation. Because of the inherent inaccuracy associated with yield point measurements there is little point in using relatively complex equations to fit data, as was done by Anderson et mnl., rather than the simpler, widely used Hall-Petch equation. In compiling their table of data, it is surprising that they did not include results from certain low-carbon steels,31 in which, as illustrated in Fig. 2, the grain-size range is very much larger than in their Armco Iron. The very fine grains in these steels were obtained by a thermomechanical process. Examination by electron microscopy showed that the grains were separated by high-angle boundarie and contained only an occasional subboundary. The data from these steels obeyed the Hall-Petch equation, and it was shown quite conclusively that they did not fit a d-l or (1-lJ3 relationship. Obviously, a much wider range in grain size than used by Anderson et al. is desirable if we are to determine the true relation between lower yield stress and grain size.

Jan 1, 1969

By D. M. Schuster, E. Scala

The elastic effects occurring in the matrix of a composite reinforced by discontinuous fibers were studied by means of photoelastic techniques. A hirefringent plastic was employed as the matrix material with high-strength a Al2O3 whiskers as the reinforcing fibers. It was found that for whiskers aligned parallel to the tensile load direction: (I) Matrix reinforcement occurred along the length of the whisker to within about 5 diameters of the whisker tip for a length to diameter ratio, L/D, of 40. (2) Significant stress concentrations were created in regions immediately surrounding the tips; the fine as-formed tapered ends exhibited the minimum stress concentration whereas the square-ended whisker produced relatively high values, K r 2.5 for L/D = 40. (3) The axial and radial stress distributions could he determined quantitatively; the stress distribution at the whisker-matrix interface was in general agreement with theoretical calculations. (4) The highest source of stress concentration occurred at points of fracture in whiskers which had ruptured after incorporation into the composite. Whiskers aligned perpendicular to the load direction neither reinforced nor caused appreciahle stress concentrations in the matrix. ThE properties of composites have generally been formulated empirically on the basis of macroscopic tests. There are still many questions concerning the mechanical and chemical interactions occurring at the interface between the reinforcing fiber and its matrix. Continuously reinforced plastics and dispersion-hardened metals represent the two extremes of composite reinforcement. Whether artificially produced or formed in situ, the whisker composite falls between these two extremes and is an example of discontinuous fiber reinforcement. The effect of fiber shape, size, surface condition, and end configuration on the stress distribution in the matrix is important since the presence of stress concentrations, especially in any high-strength, thin-wall structure, could become the cause of catastrophic failure. DOW,' in his theoretical discussion of discontinuous fiber reinforcement, has pointed out that appreciable stress concentrations occur at the tips or ends of the reinforcing fibers. It is the purpose of this study to examine directly, by means of the photoelastic technique, the stresses which occur in the vicinity of a discontinuity or whisker tip and to measure qualitatively and quantitatively the effects of whisker geometry when embedded in a birefringent matrix material. The use of sapphire (a A1,O3) whiskers was decided upon as the reinforcing agent because of their high elastic modulus (E- 60 X 106 psi) and in some cases strengths in excess of one and a half million psi. Sapphire whiskers are of further practical interest since they retain large fractions of their strength up to temperatures approaching the melting point (3720oF).2 The whiskers were grown, by the vapor-phase reaction commonly employed,3 as part of this study to insure a physically uniform supply. Tensile and bend tests were performed to verify that the whiskers were of the expected ultra-high strength. The high-strength whiskers can be identified and selected from the combustion boats by surface perfection, shape, and size; otherwise, strength values can vary by a factor of ten or more. Macroscopic defects are quite common on the surface of large bladed whiskers and the principal experiments were conducted with hexagonal whiskers of about 0.002 in. diameter and lengths ranging from 0.1 to 0.4 in. Upon completion of these two phases of the experiment, several birefringent resins were evaluated. A plastic, developed by Zandman,4 which is supplied by the Budd Co., was found most suitable and was used as the matrix material for the whisker composite throughout the study. It has a sensitivity of 60.5 lb per in. order, calibrated in tension and cures without introducing residual stresses. Young's modulus for this matrix material is 430,000 psi in the fully cured condition. Since good wetting and bonding between the sapphire and the matrix material is essential to the interpretation of the results, a wettability test was performed. The contact angle was measured to be 168 deg where perfect wetting is defined as 180 deg; therefore, the Budd Plastic wets the sapphire

Jan 1, 1964

By W. Edeburn, H. R. Fife

An extended study of dustproofing Freeport-seam coal has emphasized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption propcrties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measurements on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average tori of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by surface area. Wax extraction data on 1-in. to 0 slack from mine-run treated Freeport-searn coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness. The actual cost of the pretipple and supplemental treatments was very low per ton of coal treated, while the net or true cost was sufficiently

Jan 1, 1938

By W. Edeburn, H. R. Fife

An extended study of dustproofing Freeport-seam coal has emphasized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption propcrties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measurements on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average tori of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by surface area. Wax extraction data on 1-in. to 0 slack from mine-run treated Freeport-searn coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness. The actual cost of the pretipple and supplemental treatments was very low per ton of coal treated, while the net or true cost was sufficiently

Jan 1, 1938

By J. R. Mihalisin

Phase changes in as-cast alloys in the Ni2 CoCr-Ni, Ti-NSAl system containing 0.1 wt pct C were studied after heat treatment at 1650°F. It was found that a vegion of CrCo-type s was developed in this system after I1000 hr. The tendency for s formation was dePendent upon the aluminum and litanium content, the s -forming tendency generally becoming more pro-nounced as the latter two elements are increased. s lended to form in interdendritic regioues and was associated with solutioning- of- carbide phases. Electron- vacancy computations for prediction of s formation on these alloys mere in sufficient agreement with what was observed experimentally to indicate that the method should be of value in assessing a-forming potential in cast alloys. However, the correlation of electrotz- vacancy numbers may not be as favorable in cast as cormpared to wrought alloys. THE increasing use of high-temperature alloys for longer times at higher temperatures has resulted in a real need for obtaining information on the phase changes taking place in these alloys since these changes often have a direct effect on properties. This paper reports on a study of the phase changes in Ni-Cr-Co-Al-Ti alloys after prolonged heating at 1650°F. The alloys were selected from the pseudo-ternary system Ni2CoCr-Ni3Ti-Ni3Al and this system was chosen because it is the basis of many of the newer cast commercial superalloys. The attempt here was not to define accurately the boundaries of s formation in the NizCoCr-Ni3Ti-Ni3Al system but to delineate the phase transformations taking place upon heating alloys covering a wide range of chemistries in this system. An addition of carbon was made to all alloys to further simulate commercial alloys. It was hoped that the information generated in this manner would be of more direct use to superalloy designers than an equilibrium diagram approach since commercial alloys generally have outlived their usefulness when equilibrium is attained. EXPERIMENTAL PROCEDURE The alloys were vacuum-melted from carbonyl-nickel pellet, vacuum-grade chromium, electrolytic cobalt, high-purity aluminum and titanium, and spec-trographic-grade carbon.

Jan 1, 1968

By E. P. Pfleider, W. G. Pariseau

Even as the rational selection of excavation equipment requires a matching of machine performance capabilities to rock response characteristics, the functional features of transportation systems must be matched to the characteristics of the materials handled in order to secure optimum, trouble-free operation. In particular, ore passes and chutes must be designed for flow in order to insure controlled draw whenever a chute is opened. The alternative to quantitative design is, of course, the well known ad hoc procedure of freeing plugged ore passes, cleaning up spillage from flooded chutes, etc., after installation of the system. Since the voluminous empirical work sporadically undertaken through the years evidently had not led to reliable design methodology, it seemed worthwhile to attempt a rational and complete description of the movement of material through ore passes. The concepts of de- formable body mechanics applicable to gravity-induced flows of granular media or "soils" were involved. Accordingly, the mathematical theory of soil plasticity was adopted as a working hypothesis, and a two-dimensional laboratory model of an ore pass constructed in order to investigate the appropriateness of the theory. The general experimental strategy consisted of formulating the movement of material in ore passes as a boundary value problem in soil plasticity, determining the required boundary values of stress and velocity experimentally, and then using these data for the initiation of a theoretical solution for stress and velocity throughout the moving mass of material. A comparison between the theoretical and experimental constituted the test of the original hypothesis.

Jan 6, 1968

By Irving Cadoff, Kurt Komarek, Edward Miller

Barium can be purified by equilibration with titanium. The melting point of barium was found to be 726.2° i 0.5 °C. The room-temperature lattice parameters of BaTe and Bask are 7.004 * 0.002A and 6.600 * 0.002A. Melting points for BaTe and Base were found to be 1510° * 30°C and 1830° ± 50°C, respectively. HIGH-purity barium and its compounds are difficult to prepare because of the reactivity of barium with the atmosphere and the large heats of formation of the compounds. Purification of barium by vacuum distillation,' and the preparation and properties of barium oxide2 and barium sulfide3 have been reported. However, little has been done on the homologous compounds barium selenide and telluride. PURIFICATION OF BARIUM Distilled barium obtained from King Laboratories was used as the starting material. The analysis supplied with the metal showed the presence of: 0.4 wt pct Sr, 0.001 pct Mg, 0.02 pct F, 0.003 pct Cu, 0.005 pct Na and less than 5 x 10-3 wt pct of any other metallic impurity. Analyses for oxygen and nitrogen were not available. Since there is evidence4 that any barium nitride present in the starting material may decompose on distillation producing nitrogen which can contaminate the distillate, further purification was performed. At elevated temperatures, any nitrogen and oxygen present in barium should be removed by reaction with titanium. Assuming that the solubility of oxygen in liquid barium is negligible near the melting point of barium, any oxygen present will be in the form of BaO. Removal of oxygen from molten barium is expressed by the equation: BaO(S)+ TixOy(S) = Ba(l)+ TixO(y+1)(s) where Ti,Oy and TixO(y+1) are solid solutions of oxygen in titanium. At 1000°C, the change in free energy for this reaction is negative for (y+1)/x +y+1) x (100) 17.5 at. pct O.5 Since reaction with commercially pure titanium (containing 0.07 wt pct oxygen) results in a free energy change for the reaction of -19 kcal per g-atom, slight solubility of oxygen in barium would not hinder the oxygen removal. Since comparable thermodynamic data are not available to permit calculation of the partition of nitrogen between liquid barium and titanium, a similar quantitative relationship cannot be obtained. However, on the basis of work by Kubaschewski and Dench,5 complete removal of nitrogen from liquid barium can be expected. Since the melting point of barium is depressed markedly by small additions of nitrogen,' the change in melting point during reaction of barium with titanium was used to follow the purification reaction. MELTING POINT OF BARIUM A 50-g sample of barium was sealed by arc welding under argon into an all titanium crucible provided with a thermocouple well. The melting point of the sample was determined by thermal analysis, using a Pt/Pt-10 pct Rh thermocouple which was calibrated according to National Bureau of Standards specification6. The crucible was then heated for 48 hr at 950°C in vacuum and the melting point redetermined. This procedure was repeated until three successive thermal analyses agreed within ±0.5oC, the limits of error of the analysis. The melting point increased from an initial value of 720.0°C to a final value of 726.2°C. Analysis on samples quenched from 950°C gave a solubility value of 0.004 wt. pct Ti. Assuming that the titanium-barium phase diagram is similar to those of titanium-magnesium7 and titanium-calcium,8 the solubility of titanium in liquid barium decreases with decreasing temperature. Therefore, the solubility of titanium in liquid barium should be less than 0.004 wt. pctat the melting point (726oC), and the effect of dissolved titanium on the melting point would be negligible. Addition of up to 3 wt pct Sr does not significantly change the melting point of barium,7 so that the effect of the 0.4 wt pct Sr in the starting material will also be negligible. The value of 726.2" ± 0.5C obtained for the melting point of barium can be compared .with a determination carried out by Keller and coworkers in low-carbon steel crucibles,' who obtained a value of 725± 1C, using barium purified by fractional distillation. The higher value obtained in the present investigation is indicative of the effectiveness of titanium in removing traces of nitrogen. PREPARATION OF BaTe AND Base The compounds were prepared by direct reaction

Jan 1, 1961

By M. J. Coolbaugh

There is a need for concepts and techniques developed specifically for blasting in areas where the rock is loose or highly fractured. Common practice has been to use techniques developed in hard homogeneous rock and reduce the amount and strength of explosive. However, this rule cannot cope with all of the special characteristics of highly fractured rock and has not adequately taken care of the problems of overbreak, gouging, and wall damage. The main problems encountered when blasting in highly fractured rock are controlling the amount of rock broken, minimizing the damage done to the remaining wall material, and adapting blasting methods to rapidly fluctuating ground conditions. In addition, because it frequently needs timber support right into the blasting area, there is also the problem of how not to shoot out the timber when heavy loading is needed in order to offset a loss of impact caused by deflection of the detonation wave off the numerous rock interfaces, and by the absorption of the wave by resilient clay particles. Another consideration is the fact that less attention needs to be directed toward producing satisfactory fragmentation of the broken rock. Those blasting methods designed for breaking hard rock into manageable segments are, as a rule, not needed in highly fractured rock which will usually break along its own numerous fracture lines.

Jan 8, 1965

By H. W. Knott, M. H. Mueller

The crystal structures of Ti2Cu, Ti2Ni, Ti4Ni2O, and Ti4Cu20 have been determined using powder specimens examined by X-ray and neutron diffraction. Lattice constants have been determined for all four phases using X-ray powder diffraction films. Atom positional parameters of all four phases have been determined from observed neutron intensities. X-ray diffraction calculated intensity data have been presented also for the phase Ti2Cu to point out the particular suitability of neutron diffraction in this case. Interatomic distances have been determined using the positional parameters obtained from neutron diffraction. ALTHOUGH some investigations of the crystal structures have been made of these four compounds previously,'-13 it was the purpose of the present investigation to expand the previous work in order to locate the various atoms, determine their coordinates, and to confirm or to correct some of the previous work. It was convenient to group these four compounds together since they are related chemicallv and/or structurally. The compound Ti2Cu is tetragonil; and Ti2Ni, Ti4Ni2O, and Ti4CU2O are all large fees of the same space group. Ti2Cu has been previously reported as a fee phase by Laves and Wallbaum;1 and Rostoker2 which was possibly the oxide phase, Ti4Cu20. Joukainen, Grant, and Floe;3 and Trzebiatowski, Berak, and Ramotow-ski4 have also reported a phase of this composition. karlsson5 has reported a small fct phase of the composition Ti3Cu which may be the presently discussed Ti2Cu phase. More recently Ence and Margolin6 have reported a small fct phase for Ti2Cu and the present authors7 together with Nevitt8 have briefly reported it to be a bet related to the fct with a co three times the length of the co of the fct and have also reported that this phase has a very limited composition. Further refinements will be reported which have varied some of the parameters of this bct structure slightly. Ti2Ni has been reported as a fee phase by Laves and wallbaum;1 Duwez and taylor;9 Rostoker;2 Poole and Hume-Rothery;10 and Yurko, Barton, and parr.11 In a later paper Yurko, Barton, and parr12 have given the complete structure of this phase based on an X-ray diffraction study which was independently confirmed with neutron diffraction by Mueller and knott.7 Additional crystal structure information will be given. Ti4Ti2O, Ti4Cu2O, and a number of other compounds including Ti4Fe2O have been reported as fcc phases by Rostoker,2 and more recently Nevitt13 has confirmed the Ti4Ti2O phase. Rostoker,2 however has reported diffraction lines for Ti4Fe2O which do not have all odd or all even indices. These lines, therefore, cannot be observed if this compound has a fee structure. This same error has crept into the diffraction results reported for TiNi2O and Ti4Cu20 in the ASTM powder data which has been credited from Rostoker's data. Complete crystal structures of these two phases will be presented. Although all four of these structures have large unit cells and hence do not lend themselves for completely resolved neutron powder patterns, a sufficient number of individual reflections was observed for solving the structure. They also serve as good examples of some of the advantages to be gained by using both neutron and X-ray diffraction techniques. EXPERIMENTAL PROCEDURE All of the alloys were prepared by arc melting. The starting metals had the following purity: Cu 99.999 pct, Ni 99.83 pct, and Ti 99.92 pct. Oxygen was introduced into the two oxide phases as chemically pure TiO2, with the remainder of the titanium coming from the above mentioned metal. All of the sample buttons were annealed in evacuated Vycor tubes, the two binary phases for 5 days at 700°C and the two oxide phases for 3 days at 900°C. Oxygen analyses were performed on all four phases by two independent laboratories with the following amounts of oxygen present in atomic percent; Ti2Cu-0.06, Ti2Ni-1.03, Ti4Ni2O-13.95, and Ti4Cu20-13.87. The stoichiometric amount for the oxide phases is 14.29 at. pct. Since all of the samples were very brittle they were easily reduced to a powder for diffraction measurements. The lattice constants given in Table I were determined for the four compounds from X-ray diffraction patterns of powder samples exposed to filtered copper radiation using a 114.59 mm diam Debye-Scherrer type camera using the Straumanis loading. None of the patterns showed a detectable amount of a second phase. The lattice constants were obtained from an IBM 704 computer program employing a least squares treatment with systematic correction terms as previously reported.14

Jan 1, 1963

NEW MEMBER, The following list comprises the names of those persons who became members during the period Mar. 10 to Apr. 10, 1915: Members ADAMS, Louis WINFIELD, Supt., Rolling Mills, Lehigh Plant, Bethlehem Steel Co., So. Bethlehem, Pa.. ALLEN, ARTHUR WATTS, Mine Mgr Rodeo, San Juan, Argentina., BALL, EDWIN MARCOTTEL, Mine Supt., Ishkooda. Mines, Care Tenn. Coal, Iron & R. R. Co., H.F.D. 1, Birmingham, Ala. BOLN, CHARLES A., Oil salesman 135 S. 2d St., Philadelphia., Pa. BOYD, DAVID F., Naval Officer Navy Department, Washington, D. C. CAPERTON, GEORGE HENRY Charleston, W. Va. COGGESHALL, GEORGE W., Chem. Engr., Institute of Industrial Research, Washington D C

Jan 5, 1915

By H. L. Monroe

Meramec Mining Co., owned 50% by St. Joseph Lead Co. and 50% by Bethlehem Steel Corp., is engaged in mining, concentrating and pelletizing iron ore from the Pea Ridge Mine which is located about 75 miles southwest of St. Louis. The Pea Ridge orebody lies under some 1300 ft of limestone, dolomite, shale, and sandstone. It runs from east to west for about 1/2 mile and varies in width up to a maximum of around 600 ft. The orebody dips about 80" S. The ore is high grade magnetite with some local zones of specular hematite. The Precambrian country rock is rhyolite porphyry.

Jan 12, 1965

By F. C. Smyers, E. W. Merrick

ALTHOUGH the zinc and pyrite concentrates produced at Midvale go to other companies, the United States Smelting Refining and Mining Company smelts and refines its own lead. Refining is the first step of the process that is done at some distance from the mining operations, the plant being at East Chicago, Ind., an industrial center about 25 miles southeast of Chicago. For years it has been notable as being the only lead refinery in the country using the Betts electrolytic process. The original buildings, many of which are still in use, were erected in 1906 when the plant was known as the United States Metals Refining Co. In 1920 the parent company sold its copper refinery at Chrome, N. J., and since the copper refinery was also known as the U. S.

Jan 1, 1948