Search Documents

By Charles W. Wright

At most mines where large tonnages are handled, "bulldozing" or secondary blasting is an important and costly operation. To reduce the large blocks from primary blasting operations or stoping so that they will be small enough to pass through the chutes into the cars at the haulage level, and not too large for the crushing plant, requires blasting. Often this is done by placing a few sticks of dynamite on top of a block with or without a capping of mud, but to consume less dynamite and to promote safety, most secondary blasting is now done by blockholing, or the drilling of holes 6 to 12 in. long in the blocks, using only a part of a stick of dynamite per hole. Regardless of the method of blasting, however, the term "bulldozing chamber" is applied to the room where this work is done. Bulldozing chambers permit secondary blasting at all times in a safe place without disturbance to the other mining operations. The chambers are usually high above the haulage level and well below the stope level or open-pit floor. In most instances the material is passed through a grizzly in the bulldozing chamber, but sometimes no grizzlies are used. One to four raises extend from the chamber to the stope floor and one or two from the haulage level to the chamber floor. Occasionally large slabs of ore or rock choke the raises above the bulldozing chamber, and these have to be blasted by attaching a bundle of dynamite sticks on the end of a long pole and placing them up in the raise between the pieces causing the choke. This is called "chute-blasting." To give a picture of the progressive developments in the use of the bulldozing chamber, a few typical mines that show the application of this method to both metal and limestone mines have been selected for description here. Limestone mines have been included because many metal miners do not realize to what extent the nonmetallic, or rock, miners' are now applying metal-mining methods successfully in their operations. The bulldozing chamber is the "neck of the bottle" for some mines.

Jan 1, 1937

By A. A. Brant

Mining men, quite as exploration minded as petroleum interests, are in the position where most of the exposed crustal portions of the earth have been examined, where the demand for metals is high and likely to continue so, and yet where, perhaps, the tools fail for the economic exploration of many of the possible mineral areas more deeply covered with drift, alluvium, and later formations. At the same time the incentive exists to create acceptable substitutes for many of the duties of metal. The problem of the economic exploration of possible mineral-bearing areas is hence a vital one. In oil exploration, the absence of surface or shallow occurrences and the high cost of test drilling has led to the intensive study of geophysical techniques. Hence the development of the seismic method with its high certainty factor and its adaptability to standardized procedure.

Jan 1, 1949

By Frederic Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 166,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1943

By Frederic Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 166,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1943

By F. R. Koeberlin

ABOUT thirty miles south of the port of Coquimbo, Chile, nestling in one of the western outliers of the main Andes range, lies the little mining town of Andacollo, a place whose history and traditions make up one of the most romantic pages in the life story of this southern republic. The beginning of Andacollo is shrouded in the penumbra of the pre-Columbian era, but its first mining activity probably dates from about the years 1440 to 1460. It was in the middle of the fifteenth century that the Inca Tupac-Yupanqui, grandfather of Atahualpa, conquered this part of Chile. His domain extended even as far south as the present site of Santiago, and perhaps farther, but was maintained with increasing difficulty against the fiercely independent and indomitable tribes of Araucanian Indians of the South.

Jan 1, 1938

By F. Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimoniallead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1944

By Robert C. Stephenson

Large deposits of titaniferous magnetite occur associated with anorthosite and gabbro in the Lake Sanford area, Essex County, New York. The ore, gabbro, and anortbosite show consanguineous relations. Anorthosite grades through gabbroic anortbosite into gabbro but is locally intruded by gabbro. Structural and petrographic evidence suggests that gabbro was differentiated from anorthosite by filter pressing. Field and laboratory study of ore occurrences indicates that an ore residuum concentrated in the gabbro through magmatic segregation' by normal crystallization and flowage. Ore occurs as bands which grade into gabbro, and also as large masses which replace anorthosite. Ore in the gabbro is finer grained and richer in ilmenite than ore in anorthosite. Introduction The Lake Sanford area lies in the heart of the Adirondack Mountains, in the southeast portion of the Santanoni Quadrangle (Fig. I), and there are four ore bodies in the area immediately surrounding Lake Sanford. The area lies 30 miles by highway from the railroad at North Creek. The deposits were discovered in 1826, and from then until 1858 iron was produced in small quantities. They were idle from 1858 to 1906. Between 1906 and 1913, extensive development work was carried on. These early attempts to produce iron ore were thwarted by transportation difficulties and by the titanium content of the ore, which, ironically, has been the element responsible for the present development. In 1941 the National Lead Co., Titanium Division, developed the Sanford Hill ore body and is now producing ilmenite and magnetite concentrates.18 The Defense Plant Corporation is extending the railroad to the property from North Creek and is building a sintering plant to treat the magnetite concentrate. Investigations OF the Deposits* Early studies of the Lake Sanford titaniferous magnetite deposits were made by Emmons in 1842,l2 by Kemp, in 1897-98'0 and by Newland in 1908.22 Singewald26 and Osborne23 considered these deposits along with numerous other titaniferous magnetite deposits in 1913 and 1928, respectively. None of these reports entailed a detailed study of the ore occurrence in this area. The present study was begun in 1940. Seven months were spent in the field, and considerable time was spent in labora-

Jan 1, 1949

By Robert C. Stephenson

Large deposits of titaniferous magnetite occur associated with anorthosite and gabbro in the Lake Sanford area, Essex County, New York. The ore, gabbro, and anortbosite show consanguineous relations. Anorthosite grades through gabbroic anortbosite into gabbro but is locally intruded by gabbro. Structural and petrographic evidence suggests that gabbro was differentiated from anorthosite by filter pressing. Field and laboratory study of ore occurrences indicates that an ore residuum concentrated in the gabbro through magmatic segregation' by normal crystallization and flowage. Ore occurs as bands which grade into gabbro, and also as large masses which replace anorthosite. Ore in the gabbro is finer grained and richer in ilmenite than ore in anorthosite. Introduction The Lake Sanford area lies in the heart of the Adirondack Mountains, in the southeast portion of the Santanoni Quadrangle (Fig. I), and there are four ore bodies in the area immediately surrounding Lake Sanford. The area lies 30 miles by highway from the railroad at North Creek. The deposits were discovered in 1826, and from then until 1858 iron was produced in small quantities. They were idle from 1858 to 1906. Between 1906 and 1913, extensive development work was carried on. These early attempts to produce iron ore were thwarted by transportation difficulties and by the titanium content of the ore, which, ironically, has been the element responsible for the present development. In 1941 the National Lead Co., Titanium Division, developed the Sanford Hill ore body and is now producing ilmenite and magnetite concentrates.18 The Defense Plant Corporation is extending the railroad to the property from North Creek and is building a sintering plant to treat the magnetite concentrate. Investigations OF the Deposits* Early studies of the Lake Sanford titaniferous magnetite deposits were made by Emmons in 1842,l2 by Kemp, in 1897-98'0 and by Newland in 1908.22 Singewald26 and Osborne23 considered these deposits along with numerous other titaniferous magnetite deposits in 1913 and 1928, respectively. None of these reports entailed a detailed study of the ore occurrence in this area. The present study was begun in 1940. Seven months were spent in the field, and considerable time was spent in labora-

Jan 1, 1949

By Colin J. Dixon

The full realization of the potential of computers in geological in- formation system demands new approaches to the machine representation of information. At the same time, the feasibility of such a system, particularly in commercial field, demands greater freedom in input preparation and a degree of standardization in the arrangement of subject matter system. The paper describes some of the basic notions of project "GEOSEMANTICA 70". The aim of the project is to devise means of storing real geological informations in a machine rather than the representation of the information in human language form. This is seen as the only long-term solution to the problems of the complex vocabulary of geology and the complex syntax of geological description. Effectively, a machine language is being defined, consisting of a set of symbols and a date structure for representation of geological and related information. Beyond this, is the definition of a set of rules allowing the use of constrained text as an input/output medium. The investigation is oriented primarily to the representation and handling of information about mineral deposits and the associated geographic, economic and engineering information.

Jan 1, 1969

By Frank J. Tolonen

BENEFICIATION of iron-bearing formations is one of the major problems of research at the Michigan College of Mining arid Technology. Funds for this purpose hate been supplied by the State of Michigan supplemented by contributions of labor and some supplies from the Federal Government during the depression. The iron-mining companies have cooperated in securing samples and have also furnished much valuable information relative to the various formations.

Jan 1, 1937

By G. Derge, Lo Ching Chang

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By G. Derge

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

JOINT convention week has become a feature of the year with western mining men. The first was held at Denver in 1926, the second at Salt Lake City in 1927, and the third is about to take place at Los Angeles. Holding in the same city in one week the meetings of a number of related organizations has been .found to permit the development of a well-rounded program at the same time that it economizes time and money for the members, many of whom belong to several of the participating organizations. For the third time, the American Mining Congress, represented by its Western Division, of which Philip Wiseman is chairman, is taking the lead and assuming the main responsibility. The A.I.M.E. is furnishing the papers for two sessions and the California Development Association for one. The Southern California Section, Robert R. Boyd, chairman, is host for the Institute, but the Northern California, Nevada and Arizona sections have each contributed papers to the program, and will be represented at the meeting. It will be a real reunion of the mining men of the Southwest.

Sep 1, 1928

By Harvey S. Mudd

WHEN talking about Europe it is well to endeavor to keep politics and economics apart but they have become so intermingled in recent years that the discussion of one topic inevitably leads to the other. Economic influences formerly prevailed over politics but today national and international economies are governed by political forces. Commerce in raw materials, food, and manufactured products is now so restricted by governmental controls that the capacity of the world to produce and to consume, to exchange goods and to pay for them, cannot be gauged by the past or predicted by a multitude of experts. In prewar days there were some yardsticks but today there are none. Thus it is hazardous to make forecasts, for in all fields of human effort the world has been cast upon an uncharted sea.

Jan 1, 1947

INTRODUCTION The International Finance Corporation (IFC) is affiliated with the International Bank for Reconstruction and Development (World Bank) but operates with a separate staff and funding. It supplements the activities of the Bank by providing, to private business, equity and loans without government guarantees in whatever form and combination most suited to the project. IFC frequently complements the Bank's activities by utilizing, for example, the Bank's public sector infrastructure activities to support IFC's private sector projects. In the case of local financial institutions especially, IFC collaborates with the Bank by providing technical and financial assistance. IFC is the world's largest multilateral organization which finances private sector business in developing countries. IFC's fundamental purpose is to promote the economic development of its developing member countries through the support of the private sector. Of the 124 member countries of IFC, more than 100 are developing countries. Since it began operations in 1956, IFC has been associated with more than 2,000 companies and financial institutions in supporting over 700 business ventures in more than 80 countries. The total capital costs of these projects exceeds $26,000 million. In the 1984 fiscal year, IFC approved 62 projects in 37 countries with a total project cost of $2,473 million. IFC will make investments only if sufficient capital cannot be obtained on reasonable terms from other sources. IFC often serves as the catalyst for a project by encouraging other investors--from inside and outside the host country--to make their own equity investments along with the local sponsor for a particular project. IFC'S SPECIAL ROLE The significance of IFC's role extends beyond just its financing and technical assistance: IFC's capability to raise investor confidence in a project and to help all the participants to arrive at mutually satisfactory investment arrangements is its distinctive character. Direct Investments IFC invests in all types of projects both large and small. Heavy industrial ventures not only supply essential materials and equipment for other domestic enterprises, but also earn foreign exchange through exports. In recent years, increased emphasis has been placed on agriculture and agribusiness products, aquaculture, food and food processing, and other renewable and nonrenewable resources such as metals and energy. [ ] An overall objective of IFC is to assist entrepreneurs and others in the private sector raise the needed capital for business ventures. IFC does not compete with, nor seek to replace private initiative and capital. Rather, IFC helps to raise funds in order to undertake projects that would otherwise be held back by the lack of adequate funding. IFC can do this in several ways: IFC can invest in equity and make loans for its own account. But beyond that, IFC can reach out into the international capital markets in search of additional capital. Because of IFC's 25 years experience and record, outside investors who might otherwise be

Jan 1, 1985

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

CRUSHING and concentration flow-sheets of western mills have become greatly simplified and more or less standardized of recent years with the introduction of modern grinding methods and flotation. Improvement has not stopped, however, and advancement is continually being made in crushing and milling practice. A case in point, where remarkable improvements in efficiency have resulted from comparatively minor changes in the flow-sheet, is in the New Cornelia mill of the Calumet and Arizona Mining Co. at Ajo, Ariz. This mill, completed in 1924 for the concentration ,of the sulfide ores of the New Cornelia mine, was originally designed for a 5000-ton capacity. Before recent changes and additions were made the five 1000-ton units were handling 6500 to 7000 tons per day, giving a flotation feed of approximately 14 per

Jan 1, 1930

By G. L. Tufford, R. L. Bleifuss

Low-grade manganiferous iron ores of Minnesota's Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite with subsequent magnetic separation and flotation have not given satisfactory results because, in many instances, concentrate grade and manganese recovery are low. Metallization of iron and concurrent reduction of higher manganese oxides to MnO, as in the R-N process, followed by recovery of iron by magnetic separation and manganese by leaching, seems to be a technically feasible process. High-temperature x-ray diffraction studies show that solid-state reactions between iron and manganese, with the formation of intermediate iron-manganese oxides, occur during reduction and affect recovery of both iron and manganese from the final product. Solid state reactions also occur between FeO, MnO, and SiO, at temperatures as low as 900°C. The kinetics of these reactions are such that they become an important factor in the treatment of ores by the R-N process. These investigations suggest a temperature and gas composition cycle that would maximize both iron and manganese recovery. During the past ten years, iron ore shipments from the Cuyuna Range of Minnesota have decreased sharp1y. Because of adverse grade, structure, and cost, many Cuyuna ores are no longer competitive with high-grade foreign ores and domestic pellets. The low-grade manganiferous iron ores from the Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite for subsequent magnetic separation and flotation has not given satisfactory results because concentrate grade and manganese recovery are often low. However, a technically feasible process appears to be metallization of the iron and concurrent reduction of manganese oxides to MnO with recovery of metallic iron by magnetic separation and extraction of manganese from the tailings by leaching. In 1962 the R-N Corp., with a grant from the Area Redevelopment Administration, conducted an amenability study of the metallization of manganiferous iron ore from the Cuyuna Range. The results of this preliminary investigation were sufficient to interest the Economic Development Administration in sponsoring further studies of the process with emphasis on secondary recovery of manganese from the nonmagnetic tailings. Inasmuch as the metallization process has considerable influence on the final form of the manganese - its texture and distribution between the magnetic concentrate and nonmagnetic tailings-the investigation included a study of metallization of the ore as well. Therefore, the investigation conducted at the Mines Experiment Station covered three interrelated phases: (1) laboratory R-N roasting studies and magnetic separation tests, (2) laboratory chemical extraction experiments of the nonmagnetic tailings, and (3) a mineralogical study of the crude ores and their various roast products. High-temperature x-ray diffraction investigation of the Fe-Mn-Si0,-0, system is the main topic of this paper and an extension of the mineralogical work. GENERAL GEOLOGY The Cuyuna Range is known for its complicated geologic structure, complex orebodies, and generally indifferent response to attempts at conventional beneficiation. Several geologists have made intensive studies of the Cuyuna Range, including Leithl (1907), ~darns' (1910), Zapffe3 (1925), Grout and Wolff4 (1955), and schmidt5 (1963), whose study was the most comprehensive of all. The Range is covered with glacial deposits - till, out-wash, and lake sediments -up to 250 ft thick. Bedrock stratigraphic units of the Cuyuna Range consist of three tightly folded Precambrian sedimentary formations. The lower unit is the Mahnomen formation, composed of 2000 or more feet of argillite, slate, siltstone, and quartzite. The middle unit is the Trommald formation, which varies from 45 to 500 ft in thickness and comprises the major iron-bearing formation. The upper unit is the Rabbit Lake formation, consisting of over 2000 it of argillite, slate, and interbedded lenses of lean iron formation. In the central part of the Cuyuna Range, the units have been folded into a series of

Jan 1, 1969

By Terry E. Perkins, Len Marnewecke

Installation of a relatively simple, low-cost analog mill control system at Amax Lead Co. of Missouri's Buick concentrator has paid off handsomely. The system, which provides the capability of handling mill circuit upsets and ore changes while maintaining a desired particle size, is expected to generate annually a return on investment of several times its capital cost. In addition, the system stresses simplicity of field instrumentation and control strategy, leading to better operator acceptance and understanding, and its capital cost makes it very attractive for the specific installation when compared to more complex schemes using mass flow measurement and computers for calculating circulating load to infer particle size. This system has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value.

Jan 2, 1978