Search Documents

By L. C. Uren

Field studies and laboratory research have established the fact that the expulsive force which drives petroleum into wells, from the reservoir sands in which it is stored by nature, is primarly an expression of the energy latent within compressed natural gas dissolved or occluded in, or otherwise associated with the oil. Each barrel of oil produced is forced into the recovery well by the expansive energy of a certain volume of compressed gas, originally stored with the oil in the pores of the reservoir rock; and each cubic foot of gas so produced with the oil and expanded to atmospheric pressure reduces by so much the total natural energy available for oil expulsion. This relationship between the volumes of gas and oil produced has seemed so important that petroleum production technolo-gists have come to regard the "gas-oil ratio," or the "gas factor" as it has been more conveniently termed, as a measure of oil-production efficiency. Different methods of oil recovery and production devices are now Com pared on this basis and estimates of ultimate recovery obtainable through their use are considered by many to be inversely proportional to the values of their respective gas factors. The writer has been among those who have given support to a widcspread movement toward a proper recognition of the significance of the gas factor as a guide in the control of producing oil wells, and does not wish to oppose its more extended application. It seems necessary, how-cvcr, in view of the almost elemental faith with which the principle of the gas factor has been received in many quarters, to point out that it is a most complex factor, and one which cannot be regarded as an absolute index of production efficiency without due regard to other contributing factors by which it is influenced to an important degree. Variables Influencing Gas Factor The mere recording of a low gas factor, obtained through the use of some method or device, does not necessarily imply efficient oil production; and conversely, a high gas factor does not always signify inefficient recov-

Jan 1, 1928

By C. G. Dunn

Identification of the kinds of orientation relationships that may exist among crystals is an important problem in the metallurgical field. As an aid to its solution standard orientations of several orders of twins would be very useful for rapid analyses to discover high-order as well as low-order twin relationships. Although data have been published that give orientations for three generations of twins, these data are not readily useful in the form presented; i.e., in a stereo-graphic projection with one pole per orientation.' However, accurate data based on calculations of the positions of all {1001 planes for such groups would be very useful when presented in tabular form. Therefore, calculations have been made for a group of four orders of twins and the data are listed in Table 3. Illustrative applications are considered briefly, with the idea of pointing out what may be done with large groups of orientations. Method of Computing Orientation OF a Twin It is common practice to describe the orientation of a crystal in terms of the positions on a stereographic net of the poles of certain planes of the crystal. A single position on a net may be given in terms of two angle variables, two sets of which appear in the following equations: Polar Net Wulff Net x = , sin ?p cos Fbp x = r COS ?w y = r sin ?p sin Fp y = r sin ?w cos Fw % = r cos ?p z = r sin ?w, sin +, The three numbers z, y and z determine a length r as well as a direction (0, 4) in an X, Y, Z coordinate system. In the present case, r will be set equal to (h2 + k2 + L2)1/2, where h, k and I are the usual Miller indices for a crystallographic plane, a restriction that facilitates determination of the positions of poles of new planes from those of old or known ones,2 as will become evident later. Furthermore, since twinned lattices have certain planes in common, it is an easy matter to determine the orientation of a twin of a crystal if the orientation of the crystal itself is known. We start therefore with a crystal of known orientation (positions of three {Ioo} poles given) and determine where the cube poles occur in first, second, third and fourth-order twins. Methods for identifying twinned lattices and for making the calculations to find the orientation of a twin have been published.3,4' Reference 4 will be illustrated in the calculation of the orientation of a twin, even though this method differs from the one used by the writer in obtaining the following data on four orders of twins. Consider a crystal S and its twin A1, A' being one of the four {112} or {III} type* first-order twills of S. The orientation of S—i.e., the positions of poles of (I00)

Jan 1, 1945

By Chester Fulton

IN Polk County, Florida, the mining of raw phosphates began some 50 years ago with dredging operations on the Peace River, and in other near-by places by removal of shallow overburden with negroes and wheelbarrows, or with mules and scrapers, and the excavation and screen-ing of deposits found close to the surface. There were many individual operations of comparatively short life. Later steam shovels removed the overburden, and still later hydraulic methods were substituted for the steam shovel. Within the last 10 years large electrically operated drag-lines have almost entirely replaced hydraulic mining for overburden removal. The matrix is still mined by hydraulic giants and pumped to the washer or recovery plant. The many small operations have long since disappeared and the most desirable phosphate lands have gradually been acquired through purchase or merger by the seven companies that are operating in the field today. These companies are producing and selling about 2,000,000 long tons of phosphate per annum, or about two-thirds of what the industry likes to think is the normal output, with 1929 and 1930 in mind. To produce these 2,000,000 long tons of raw phosphate, they mine and treat about 1,000,000 tons of tailings from older and less efficient opera-tions, about 11,000,000 tons of matrix, and remove from above this matrix some 22,000,000 tons of overburden. The mining practice that has made possible the excavation and handling of 34 million tons of material to win but 2 million tons of merchantable product, selling for probably an average of only $4 per long ton when dried, should be of interest to the mining profession, though little has been written of it. The Florida Pebble Field, as it has come to be known, comprises an area (Fig. 1) within a radius of about 18 to 20 miles centering around Mulberry in Polk County, a small town 30 miles east of Tampa, Florida's largest port on the gulf coast.

Jan 1, 1936

By H. T. Van Ells

The following is a brief description of the cost accounts in effect at the mines of the Anaconda Copper Mining Co. The accompanying chart, Table I., shows the distribution of labor, materials, and redistributable accounts to the various operating and repair accounts. OperatiNG. Development. Owing to the fact that every mine has its peculiarities in formation and methods, the question of arriving at what charges should be included under the head of " Development" is one that has occasioned considerable thought and comment, and in the cost sheet of the Anaconda Copper Mining Co. this account has been sub-divided to show the expenses of breaking ground, tramming, timbering, shaft sinking, up-raising, and cutting stations and skip chutes. It has always been the policy of the company to charge the entire cost of this work to operations monthly, whether the mines are producing or not, also the cost of the opening up of new mines; and only surface construction and additions are charged to capital, excepting original machinery installed for operating pumping plants. Explanations of the charges to the various sub-accounts follow : Breaking Ground.—Work performed in driving cross-cuts from the station, or cross-cuts from the drifts, and diamond-drill work, for the purpose of discovering or developing ore bodies. Tramming.—Cost of tramming waste produced by cross-cuts mentioned above. When waste is hoisted to another level to be used for filling, the charge to this account stops at the station, and when hoisted to surface the charge includes tramming from the collar of the shaft to the dump. Timbering.—Cost of timbering the cross-cuts mentioned above includes the cost of handling and framing such timbers, but does not include the wages of station tenders and top carmen.

Jan 1, 1914

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

Jan 5, 1976

By H. P. Allen

The Achotla mill of the Cia. Minera de Penoles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1939

By H. P. Allen

The Achotla mill of the Cia. Minera de Penoles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1939

By E. C. W. Perryman

The recovery of X-ray line broadening, hardness, and electrical resistivity from cold worked AI-Mg alloys has been investigated. The results, together with those from density measurements, suggest that magnesium atoms freeze in the excess vacancies formed by cold working, and that this affects the climb of dislocations during the recovery process. PREVIOUS work1, " has shown that while 1 pct Mg increases the activation energy for recrystalliza-tion, it decreases the activation energy for the recovery of mechanical properties and decreases the subgrain size both after cold working and annealing. A similar result has been reported by Varley2 for an A1-2 pct Mg alloy. With plastic deformation at high temperatures, McLean and Farmer' and Rachinger have found that magnesium appears to retard the motion of dislocations and, furthermore, they find little or no effect of magnesium on the size of subgrains formed during high temperature deformation. In view of the apparent contradictions as to the effect of magnesium on subgrain size, the recovery process in Al-Mg alloys has been investigated more thoroughly by studying the annealing out of X-ray line broadening, hardness, and electrical resistivity from alloys cold worked at room temperature. Material Used—The chemical analyses of the alloys are given in Table I. Fabrication—The material used was cold rolled 20 pct at room temperature, the grain size prior to the last cold rolling operation being similar to that used in previous work; i.e., 230. The experimental procedure for annealing, determination of X-rav half-veak breadth. hardness measurement, electEica1 resistivity, and density and metallographic examination was exactly the same as previously described." Variation of X-Ray Half-Peak Breadth with Annealing Time—Isothermal annealing curves at 100°, 200°, and 250°C were obtained for material cold worked 20 pct. The half-peak breadth of the (333) Ka, line directly after cold working is shown as a function of magnesium content in Fig. 1. Only with the 2.87 pct Mg alloy was overlapping of the a, and n.. reflections observed to any appreciable extent. To separate these, Rachinger's method' was used. Typical isothermal annealing curves are shown in Figs. 2 and 3 for 100" and 200°C, respectively. These curves are similar to those obtained previously for super-purity aluminum except that the

Jan 1, 1957

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson's discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 7 3/4 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612° F. (322° C.), they reduced the 7 3/4 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statement just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson's time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced consumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opinions advanced by different authorities in the scientific world to account for the apparent anomaly, but none,

Jan 1, 1877

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson's discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 79 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612' F. (322' C.), they redoccd the 79 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statenlent just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson's time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totsally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced colisumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opirlions advanced by different authorities in the scientific world to account for the apparent anomaly, bat none,

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1-4 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio,' in the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably those from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1952

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By L. G. Huntley

The occurrence of oil or "tar" in Mexico was mentioned as early as the seventeenth century by Friar Sagahun, who gives the Indian name "chapopote," by which these asphalt seepages are still called. This asphalt was apparently used, as it has been used by primitive people in many parts of the world, in religious ceremonies and for medicinal purposes. Travellers also report that the ruins in Yucatan and the pyramids in southern Mexico show traces of the use of "chapopotel' as a building cement.l DeGolyer says that the first attempt to exploit oil or gas in Mexico in a commercial way is shown by the records of the Memoria de Fomento of 1865, when permission was granted to a Senor Ildefonso Lopez to exploit the deposits of petroliferous substances in the San Jose de las Rusias area in the State of Tamaulipas. Other concessions follow, and probably refer to surface seepages which occur in that district. This was several years after the discovery of oil in Pennsylvania. In 1868, a well 125 it. deep was :drilled by a company organized in Mexico City, in what is now known as the,, Furbero district, and a little oil was refined there. In 1873, residents of Tampico denounced seepages along the Tamesi River, and asphalt was mined near Tempoal in the Canton of Tantoyuca. No drilling was attempted. But between 1880 and 1883 several shallow wells were drilled for oil in Mexico, two of them being near the present Potrero de Llano field west of Tuxpam. The wells were drilled by a Boston company with Canadian rigs, and are said to have reached a depth of about 400 ft., while one is reported to have flowed. Several other abortive attempts were made to drill for oil between 1885 and the beginning of the present century, about which time the Mexican Petroleum & Liquid Fuel Co., Ltd., in which Cecil Rhodes was interested drilled 24 wells unsuccessfully, several of them as deep as 1,500 ft., in the State of Vera Cruz. Also Messrs. Doheny and Canfield of California pur-

Jan 1, 1916

THE Lehigh Valley Section is planning with a num-ber of other organizations a three-day conference, April 25, 26 and 27, with field visits to cement, slate and steel plants in the vicinity of Easton, Pa. W. B. Plank is chairman and D. Knickerbocker Boyd is sec-retary. Headquarters will be at Hotel Easton. Wednesday' will be cement day. In the forenoon A. S. T. M. Committee D-16 will meet and after luncheon the delegates will visit the Martin Creek plants of the Alpha Portland Cement Co. An evening dinner and general session on cement is being arranged. Thursday morning will be devoted to a technical ses-sion on slate, and the breaking of ground for the new John Markel mining building at Lafayette College. After luncheon various slate quarries will be inspected, the visitors being guests of the companies. In the eve-ning there will be a conference dinner at Hotel Easton with a number of distinguished visitors. Friday will be given over to steel and will include a visit to Lehigh University, an inspection of the plant of the Bethlehem Steel Corp., and a luncheon as guests of the latter.

Jan 3, 1928

By Jay A. Carpenter

THIS preliminary report from the Committee to Study Relations Between Students and the Institute is submitted to our member- ship for consideration and discussion before the general subject comes up for action at the Annual Meeting in February. At present, the A. I. M. E. has a dual relationship with mining students, each relationship in no may connected with the other. To the individual student the Institute offers for $2 a year a Student Associateship in the Institute which carries with it a subscription to MINING AND METAL- 'LURGY, a watch fob, and the privilege of becoming a Junior Member after graduation without payment of the -first year's dues, if one's application is accepted. To the student's college society it offers the privilege, upon application, of becoming 'an Affiliated 'Society, which brings with it no specific supervision or aid, and in turn requires no specific conditions as to membership, fees, or rules. This Affiliated Society is distinctly a school organization which Student Associateship in the Institute can he given special status or ignored, is the local .society sees fit.

Jan 1, 1934

By Leonard Grimshaw

THE idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a com-posite steel.

Jan 1, 1936

Meeting of June 26, 1914.-The President was authorized to appoint Advisory Committees to co operate with the United States Bureau of Mines. The President announced the appointment of Edward H. Benjamin and W. C. Ralston as additional members of the Committee on Arrangements for the San Francisco meeting, 1915. H. T. Van Ells and Judd Stewart were appointed to represent the Institute on a joint committee of several technical societies to consider the standardization of graphical methods for the presentation of statistics. The President announced the appointment of H. Foster Bain to succeed Edward H. Benjamin, resigned, on the Committee of Management of the International Engineering Congress, 1915. The Secretary was authorized to issue a new circular advertising the sale of back Transactions and to sell back Transactions, bound in cloth, at a price of $35 for 46 volumes, provided sufficient orders were received to warrant the special binding. The sum of $177.50 was contributed to the San Francisco Local Section. Upon recommendation of the Committee on Membership, 70 Members, 4 Associate Members and 7 Junior Members were elected to their respective classes; there was also one change of status from Junior Member to Member.

Jan 8, 1914