Search Documents

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The technique of unidirectional solidification has been applied to the A1-AI3Ni and A1-CuAl2 ezltectic alloy systems; the controlled microstructure of A1-A3Ni consists of parallel A13Ni whiskers emhedded in an aluminum matrix while the Al-CuAl2, system solidifies as parallel alternate lamellae of aluminm and CuAl2. Mechanical tests (tension and flexure) have shown that the particle-matrix interface bond formed during unidirectional solidification allowes for efficient load transfer from the matrix to the reinforcing phase. Strength and fracture characterstics of the alloys were studied as a function of phase orientation; the tensile strength of controlled Al-Al3Ni samples was 43,000 psi (three times greater than that of as-cast specime~s). The strength of the Al-CIA2, cutectic was studied as a function of lamellae-flexure stress-axis orientation using a microbend apparatus. A twofold increase in outer fiber stress was observed as the lamellae were rotated from a position of no reinforcing (perpendicular to the stress axis) to one of maximum reinforcing (parallel to the stress axis), The brittle reinforcing constituent in each alloy (A13Ni and CuAl2) was observed to he the nucleating phase for fracture. It is to be concluded from this investigation that unidirectionally solidified eutectic alloys have a potential use as reinforcing coniposite) materials. In a recent review article, Chadwick1 has described the work of many investigators in the area of controlled solidification of binary eutectic alloys. Thus far, more than twenty eutectic alloys have been unidirectionally solidified to produce structures consisting of two phases in the form of alternating lamellae or as whiskers embedded within a continuous matrix; in either case, the phases are aligned parallel to the growth direction. In particular, Kraft and Albright2 have shown that the Al-CuA1, eutectic alloy exhibits a lamellar microstruc- ture as a result of unidirectional solidification while Lemkey, Hertzberg, and Ford3 have studied the A13Ni whisker-aluminum matrix morphology in the A1-A13Ni system. Whether these alloys could exhibit reinforcing behavior would have to depend upon the strength and volume fraction of the reinforcing phase (AI3Ni and CuA12) and the nature of the bond between the reinforcing phase and the matrix. Hertzberg and Kraft4 have shown that the interface bond between chromium whiskers and a copper matrix in unidirectionally solidified Cu-Cr is particularly good while Lemkey and Kraft5 have reported chromium-whisker tensile strengths in excess of 1,000,000 psi. However, with the chromium volume fraction being less than 2 pct, no reinforcing behavior was displayed by the Cu-Cr alloy.6 In view of the encouraging results concerning the good interfacial bond and high strength of the reinforcing phase in the Cu-Cr system and preliminary mechanical test data reported by Lemkey et al.3 for the A1-A13Ni system, the A1-CuA1, and A1-A13Ni eutectic alloys containing 50 and 10 vol pct, respectively, of the reinforcing phase give promise of possessing mechanical reinforcing behavior. Based on this premise, the objective of the investigation was to study the strength and fracture behavior exhibited by these anisotropic microstructures. EXPERIMENTAL PROCEDURE Controlled Solidification Procedure. An extensive description of the technique of unidirectional solidification has been presented elsewhere.' However, the pertinent details for each eutectic system studied are discussed below. Al-A13Ni System. Several master heats of this alloy were prepared by vacuum-induction melting in an A12O3crucible and casting in SiO2 mold or by induction melting in alumina crucibles under argon. The initial heats were prepared from 99.99 pct A1 and 99.99+ pct Ni, while later heats used 99.999+ pct A1 and 99.99+ pct Ni. Specimens of these master heats were unidirectionally solidified using induction and resistance heating sources and argon atmospheres at growth rates from 1.1 to 28.7 cm per hr. The thermal gradients in the liquid were controlled in the range of 26" to 36°C per cm for these runs. Al-CuA12 System. The master heat and controlled

Jan 1, 1965

By Maurice Magee

The Ducktown ore deposits have been known, explored, and mined for 120 years. Eight massive sulfide ore bodies occur in highly folded and metamorphosed graywacke, graywacke conglomerate, mica schist, chloritegarnet schist, and staurolite schist of Precambrian age. The ore deposits are tabular bodies that have been extensively folded, generally conform to the enclosing rocks, but show local complex differences. The ore deposits, ranging in size from 250,000 tons to over 20 million tons, are composed principally of the minerals pyrrhotite, pyrite, chalcopyrite, sphalerite, and magnetite. Gangue minerals are quartz, calcite, actinolite, tremolite, hornblende, garnet, and masses of schistose wall- rock. Three fault systems are present that have influenced ore control and ore body configuration. Hydrothermal effects are evident in wall-rock alteration. Evidence of retrograde metamorphism is extensive in the wall and ore associated rock. Preliminary isotopic age dates have indicated four possible metamorphic events during the Paleozoic Era. Ore genesis is considered to be hydrothermal replacement of receptive beds, predominantly highly calcareous zones, quartzitic zones, and brecciated shear zones. Ore deposition is thought to have occurred during the Devonian Period, with later mobilization and recrystallization of the ore and gangue during Middle and Late Paleozoic times.

Jan 1, 1968

By John Goodell

CIVIL engineers seem to number in their ranks more advocates of licensing than are found among the practitioners of other branches of the pro-fession. Licensing was not originated by civil engineers but it was forced upon them in two ways. In the first place, the civil engineering profession has hangers-on like every other profession. The first legislative result of their imperfect accomplishments with which I am familiar occurred in the far West. It was found that early irrigation works were so badly planned in some cases that not only were water rights made very uncertain but considerable sums were invested in structures and ditches which proved inadequate and occasionally complete failures. Water was too valuable to be wasted in that way and money too hard to obtain. In those sections, therefore, laws were passed many years ago which made it obligatory for the design of irrigation works and other structures utilizing water to be made by engineers who had satisfied a board of examiners that they possessed the technical qualifications to plan such works properly. The basic thought on which such laws rest is the same as that on which laws governing the licensing of boiler operators rest, namely, the safety and welfare of the public. While boiler explosions still occur and irrigation works are built which are not wholly satis-factory, these laws have helped the, public, it is gener-ally agreed.

Jan 4, 1922

By H. H. Campbell

MANY attempts have been made to write a formula by which to calculate the strength of steel from its chemical composition, but most of these endeavors have failed because there were too many disturbing conditions. It is idle to collect from the pages of trade-papers, books, or the proceedings of scientific societies, a multitude of observations. The combination of such results will simply show that steel of the same composition will vary in tensile strength through wide limits-a fact that has been known for generations. That cold-working, overheating, and many another form of heat-treatment alter fundamentally the strength of steel, is ancient history, although it is only recently that the microscope has pointed out the road to an explanation of the phenomena. It may be urged that the microscopic structure must be taken into consideration in any formula giving the ultimate strength, but from the standpoint of the present investigation this is unnecessary. We are trying to determine primarily, not what changes in ultimate strength may be made by variations in the condition of carbon, but what effect is produced by changes in the amount of carbon, when its condition remains constant. For such an inquiry, in order that the condition of the carbon should remain as nearly uniform as possible, it is essential that all test-pieces be made under the same conditions; and it is be¬lieved that the tests described in this paper satisfy that require¬ment. The investigations were made at the works of the Pennsylvania Steel Company,. Steelton, Pa.; the ingots from which the tests were made were 6 in. square in every case; they were heated in the same furnace and forged at the same ham

Jan 1, 1905

By C. WIFLARD HAYES

(New Haven Meeting, February, 1909.) I DESIRE to make it perfectly clear at the outset that I fully realize the hazardous nature of any attempt to estimate the quantity of iron-ore or any other mineral in the ground. I should not have had the temerity to venture upon an inventory of the iron-ore supplies of the United States except for the requirements of the Conservation Commission. During the preparation of this inventory I have been impressed by the wide diversity in estimates of those best qualified to. hold an opinion, and I am therefore prepared in advance for criticism of my figures. Inasmuch as this report was prepared in large part for unprofessional readers, I considered it necessary to classify and describe the commercial iron-ores in a somewhat elementary manner, in order to explain the reasons for the large element of uncertainty in the estimates. I have therefore given a chemical and a geological classification of iron-ores, which place the commercial deposits in six classes: (1) magmatic segregations in basic igneous rocks; (2) contact-deposits formed in connection with igneous intrusions; (3) concentration-deposits; (4) replacement-deposits; (5) bedded-deposits, and (6) gossan-deposits. The iron-ores are further distinguished under two classes available and not available. This classification is in large measure arbitrary, and it, is evident that it will vary front time to time. In the available class are placed those ores which can be worked at a profit under conditions essentially as they exist at present. Since it depends wholly on the question of costs, the various factors which affect cost will determine the classification of any particular deposit. Actual production, * Abstract of Report prepared for the Conservation Commission. t Chief Geologist, United States Geological Survey. .

Apr 1, 1909

By Roy Moore

THE Tom Reed Extension and Big Jim mines of United Eastern Mining Co. are situated in the Oatman district, Mohave County, Ariz., about 28 miles southwest of Kingman, the nearest railway point. Articles descriptive of the mine surface plant, mill construction, and plant operations have been written by Otto Wartenweiler1, the designing engineer; Wheeler 0. North,2 when he was assistant general manager for the company, and Earle M. Bagley, mill superintendent.3 The last article covers average costs for the full time the mill was operated. The geology of the mines is described by F. L. Ransome4 of the United States Geological Survey. Production was started in January,. 1917, and the known orebodies were exhausted in May, 1925, showing a life of seven years and five months. On account of the comparatively short life and the fact that stoping operations were confined to two orebodies, little experimenting was done with mining methods. The two orebodies were in what is generally called the Tom Reed-United Eastern vein, which occupies a fault fissure having a normal displacement of several hundred feet. Seven or eight very productive ore shoots were mined along this vein in a distance of 1 ½ miles, the two worked by the United Eastern being 1 mile apart. The maximum dimensions of the Tom Reed Extension ore shoot were height, 750. ft.; length, 950 ft.; thickness, 48 ft. The vein structure varied from a solid quartz-calcite filling to a series of parallel stringers separated by andesite. From this body, 511,976 tons of ore were mined. (Fig. 1.)

Jan 1, 1928

By T. M. Morris

R. T. Hukki (Finland Institute of Technology, Helsinki, Finland)—Two schools of thought are developing concerning the order of the rate of flotation. The paper by Morris is intended to show experimental evidence in favor of the first order rate. Arbiter, on the other hand, has presented an earlier paper" to demonstrate the validity of the second order rate equation. Unfortunately his method of plotting is open to criticism, as pointed out by Morris." A more sensitive method of plotting has been described by the writer,= whereby the data presented by Arbiter demonstrate the superiority of the second order plot. The general rate equation may be written in the following forms for the integrated first and second order equations: (A) t = -1/k In Co-R/Co (first order) [4] 1 (B) 1/t = - kCo + kCo2 1/R (second order) As a first approximation the value of Co may be taken as a unity, 100 pct or 1. Whether or not this is the case in all tests performed by Morris is impossible to judge, owing to the fact that the flotation times are extremely short, e.g. 150 sec in tests A. It would, indeed, be very interesting to know what the total recovery R would be after 1 hr of flotation, for example, instead of after 150 sec. Certainly there are circumstances when C, approaches unity within a very small margin of error. Morris has used the same approximation in his example D "since the feed to this cleaner

Jan 1, 1954

By Appendix by A. S. Goldoni, R. E. Tate, E. M. Cramer

The diffision coefficient for self-diffision of plutonium in the temperature range 350" to 440°C has been measured by using puZ3 as the tracer isotope. Autoradiopaphic techniques were used to inzlestigate the possibility of grain boundary diffusion, hut only evidence for volume diffusion was found. The least-squares fit of the data gives the .following equation for the diffision coefficient: The computer least-squares technique for fitting the nonlinear equations is outlined. DETERMINATION of the self-diffusion coefficient of the fcc 6 phase of plutonium is in principle a straightforward experimental task. However, the chemical reactivity, the intense @ activity, and the toxicity of plutonium put limitations on the experimental techniques. The technique selected included roll bonding for preparation of the diffusion couples and pulse-height analysis of the @-particle activity to determine the distribution of the PU tracer in the diffusion couples. EXPERIMENTAL PROCEDURE Couple Preparation. Cylinders about 0.5 in. in diam were cast from two special stocks of plutonium, one of which had been enriched in puZ3', as shown in the isotopic analyses listed in Table I. For each roll-bonded composite sheet, a cylinder 0.437 in. in diam and 0.190 in. thick was turned from each kind of plutonium on a lathe in a 98 pct He atmosphere. The two freshly machined cylinders were positioned face to face in a tube of commercially pure aluminum which had been sealed at one end by welding and the assembly was evacuated on a vacuum manifold overnight. The elapsed time between machining the faces of the plutonium cylinders and evacuating the loaded tube was about 15 min. After overnight evacuation of the assembly the indicated vacuum was 1 X 10"5 torr or better. The aluminum tube was then warmed and pinched off with a cold-welding tool. The pinched-off weld was also fusion-welded as an additional precaution against leakage of air into the evacuated assembly. The assembly was immediately heated for 30 min in a 250°C furnace and reduced in thickness by being passed through a rolling mill with rolls heated to 200°C. The rolling schedule (four passes of 100 mils each with a 10-min reheat after two passes) reduced the thickness of the assembly to 100 mils. The rolled assembly was allowed to cool normally in air. The rolled assembly was sheared at the edges and the aluminum peeled from the composite plutonium sheet. The elliptical sheet was about 0.060 in. thick and usually three 0.383-in.-diam disks could be punched from its central portion. The sheet was heated on a hot plate to the ductile low 0 range (140°C as measured by temperature-indicating pellets) before each disk was quickly punched. The quality of the bond in the disks was evaluated by metallographic examination of the scrap sheet adjoining the hole left by the punch. Only well-bonded specimens without oxide in the interface (as indicated by metallography) were considered satisfactory for further use. More than half of the specimens so examined contained sufficient oxide in the interface to be rejected. Diffusion Anneal. Each disk to be diffusion-annealed was wrapped in 1-mil-thick tantalum foil and sealed within a Pyrex capsule evacuated to 1 x 10~5 torr or better. This capsule was then sealed within another Pyrex capsule at a similar pressure. The diffusion anneals were carried out at temperatures between 350" and 440°C in Marshall furnaces adjusted to have a temperature gradient of not more than *1/2"C over a 5-in. length. This gradient was then further smoothed by using a nickel tube as a liner in the furnace. The liner was divided into three longitudinal cavities by a septum of nickel sheet to which two calibrated Chromel-Alumel thermocouples were attached. One thermocouple was used for controlling the furnace temperature by means of a Brown Pyrovane controller equipped with a Capaciline anticipation circuit; the second thermocouple was monitored twice daily with a Leeds and Northrup K-2 precision potentiometer.

Jan 1, 1964

By Matti J. Saarivirta

Two new precipitation hardening copper-base alloys, Cu-1.5pct Ti-2.5 pct Sn and Cu-1.5 pct Ti-2.5 pct Sn-0.4 pct Cr were developed. High strength and medium conductivity are obtained by solution annealing and subsequent heat treatment. Combination of solution annealing, cold working, and heat treatment increases the strength further. Good elevated temperature strength and ductility makes these alloys superior to copper-beryllium-cobalt alloys. A considerable amount of research work is being done throughout the world to develop new and improved copper-base alloys. In many cases, the object is to develop alloys having a combination of high electrical and thermal conductivities, and high strength. The problem is complicated by the fact that any alloying element added to increase strength, invariably decreases conductivity. Among the few commercial precipitation hardening type copper-base alloys, the Cu-Be-Co alloys are best known. These alloys are used in many applications that require good spring characteristics cornbined with high strength and moderately high electrical conductivity. They can be formed readily after solution annealing, then heat treated to obtain high strength and conductivity. Because of the relatively high cost of the Cu-Be-Co alloys, considerable research has been aimed at developing new lower cost alloys having similar properties. As far as is known today, the binary Cu-Ti alloy is the only one whose properties are

Jan 1, 1962

By Notman, Arthur

THIS is a day of surpluses, some good and some not so good. One can hardly pick up a newspaper, magazine, review or economic treatise without confronting the fact that we have or are threatened with more .of certain goods than we have use for, whether it be corn, wheat, cotton, coal or oil, -lumber, 'leather, newsprint, automobiles, zinc, lead, copper or what not. How did this unprecedented state of affairs arise? Who is to blame? How shall we avoid smothering ourselves in our own production? The voice of the farmer is raised in appeal to the Government to relieve him from the dilemma of his own fertility. In answer the Government employs thousands of experts and spends millions of dollars to aid the farmer. But to what end? To make him still more efficient so that he may produce even greater surpluses? Not satisfied with the result, it spends other millions to prepare vast areas of the arid land of the West for more farmers to cultivate and insure yet larger surpluses. Then what? Naturally another appeal to the Government to fix prices by financing the

Jan 1, 1928

By AIME AIME

A PAPER prepared by James A. Adams, development engineer of the fitline & Smelter Supply Co., and presented at the last Annual Meeting of the A.I.M.E. in New York City, de- scribed a new automatic pulp density controller which has had a most favorable reception. Manual control has until now been the universal practice in spite of its shortcomings; samples of pulp for density determination were often improperly taken, and only at the operator's convenience, so that the trend in density changes was frequently missed, and the grinding circuit al- lowed to operate under something less than the most efficient conditions.

Jan 1, 1940

By Charles H. Fulton

ONE of the events of note in mineral industry education circles during the year was the summer school for engineering teachers, devoted to mining and metallurgical engineering, which was conducted by the Society for the Promotion of Engineering Education in co¬operation with the University of Wisconsin. It was in charge of Prof. Harry P. Hammond, director of the summer school, and Prof. Richard S. McCaffery of the University of Wisconsin. It was attended by 63 people, and practically every educational institution offering mineral industry courses had representatives present. The session was successful and those in attendance spoke highly of the pro¬gram and results obtained. The Mineral Industry Education Division cooperated with the S.P.E.E. in this project. Prof. Hammond will discuss the purpose and results of this session at the February meeting.

Jan 1, 1934

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

[A AALSETH, Earl P (M 51) Consult Geol Engr 2019 Eldorado Dr, Billings, Monl ABADIE, Henry G (M 43) Asst to Supt of Oper Long Beach Oil Dev Co 925 Harbor Plaza, Long Beach 2, Calif ABBE, T Waldo (A 56) Asst Dist Oper Supt Sun Oil Co PO Box 66, Stowell, Tax ABBOTT, Fred E Jr (M 59) Abqaiq Dist Mgr Arabian American Oil Co Dhahran, Saudi, Arabia ABBOTT, Clifton T (A 60) Apartado 677, Maracaibo, Venezuela ABBOTT, J L (M 56) Partner Pritchard & Abbott 1010 Ft Worth Natl Bk Bldg, Fort Worth 2, Tex ABBOTT, Richard H (J 51) Partner Abbott & Howard 422 W Hermosa San Antonio 12, Tex .ABBOTT, William G (M 50) Div Mgr Rice Engrg & Operating Inc Box 1142, Hobbs, N. M. ABDERHALDEN, Ronald R (J 59) Prod Engr Continental Oil Co Box 100, Carmi, III ABEL, Malcolm D (J 50) Gen Partner Abel & Bancroft PO Box 865, Midland, Tex ABEL, Ramond L (M 28) Prof of Chem Eng Univ of Pittsburgh, Pittsburgh 13, Pa ABEL, Wayne K (M 57) 1513 Patton Drive, Odessa, Tex ABELL, Joseph M (J 55) Petr Engr Tennessee Gas & Oil Co Box 1772, Casper, Wyo ABELS, Thomas A (J 60) Exploit Engr Shell Oil Co Box 193, New Orleans 3, La ABENDROTH, G F (M 46) Dring Prod Supt Lyons & Logan 1500 Beck Bldg, Shreveport, La ABERCROMBIE, Bolling A (M 60) Mgr Product Planning Axelson-Garrett PO Box 2427, Longview, Tex ABERCROMBIE, C T (160) Prod Engr Cities Ser Petr Co Box 472, Brownfield, Tex ABERCROMBIE, H L Jr (J 55) Prod Engr Mobil Oil Co Room 1800 Gr PI Life Bldg, Lubbock, Tex ABERCROMBIE, Robert (J 57) Prod Engr Mobil Oil Co PO Box 1770 Shreveport, La ABERG, Richard S (M 57) Area Prod Geol Shell Oil Co of Canada, Box 100 Calgary, Alta, Canada]

Jan 1, 1961

By DAVID F. McFARLAND

THE making of courses of study and curricula has long held first place as the favorite pastime of educators. As a game, this activity is as fascinating to some as golf or bridge, 'and the golfer's hope of a low score is matched by the teacher's ambition to some day evolve a sequence of studies that shall prove the ideal preparation for a life of maximum service and, profit. There are few in, this gathering who have not tried their skill at this game and still fewer are those who have been long satisfied by the product of their efforts. A curriculum is hardly printed in the college catalog before conditions arise which seem to make changes desirable, and strong will power is needed to maintain the program long enough to give it a fair trial. Metallurgical curricula are not less subject to change than others, 'and; indeed they have seemed, at times, to change more rapidly than other curricula because of the changing 'needs of the industries and the demand that the graduate be trained to meet the new conditions. Metallurgical practice is constantly proving that "time makes ancient good uncouth," and the graduate metallurgist is required to adapt himself to newer and

Jan 1, 1930

By Herbert Hoover

BOTH the directors of industry and your leaders have made great progress toward a new and common . ground in economic conceptions, which, I am confident, has had a profound effect upon our economic progress during the last few years. That is the conception that industry must be constantly renovated by scientific research and invention; that labor welcomes those labor-saving devices; that labor gives its full and unrestricted effort to reduce costs by the use of these machines and methods; that the savings from these reduced costs shall be shared among labor, employer and the consumer.

Jan 1, 1930

By R. A. RAGATZ

THE preparation of specimens for microscopic examination from metal articles of relatively large cross-section offers no particular difficulty. It often happens, however, that articles submitted for examination are so thin that specimens satisfactory for microscopic examination can not be successfully pre- pared by the methods commonly employed when working with larger articles. Ordinarily, the preparation of metallographic specimens involves the following operations : (1) cutting the small specimens to be examined out of the larger mass of metal, (2) cleaning and electroplating, (3) mounting to furnish support during the grinding and polishing operations, (4) grinding and polishing to produce a scratch-free surface, (5) etching and drying. All of these operations must be carried out in such a manner that when the specimen is finally examined under the microscope, the structure seen is a true and well-defined representation of the structure that the larger mass of metal possesses at the place where the small specimen was removed. It is important that the deformation involved in cutting out the specimen be as slight as possible, in order that the subsequent grinding and polishing operations will completely eliminate the cold- working effects in the vicinity of the cuts. It is also important that the specimen never be allowed to attain a temperature high enough to alter its structure; the maximum permissible depends on the metal being handled. With some metals, zinc for example, consider- able care must be taken to avoid heating; with other metals, annealed steel -for example, no particular pre- cautions need be observed because there is no tendency for structural change to occur at relatively low temperatures.

Jan 1, 1929

By Rogers Wade

THE Pilares mine of the Moctezuma Copper Co. is situated at Los Pilares de Nacozari, Sonora, Mexico, about 75 mi. (120.7 km.) South of the international boundary and about 7 mi. (11.26 kin.) east of the town of Nacozari de Garcia. It is situated at an elevation of 5000 ft. (1524 m.) in one of the northward trending ridges that form part of the mountain mass that culminates in the Sierra Madre de Mexico. To the east, south, and west, the topography is rugged and diversified; to the north less diversity exists, ranges of mountains rise sharply out of almost level ground and give the basin range structure characteristic of the southwest. The climate is dry, the average rainfall of 15 in. (38 cm.) being confined almost entirely to the months of June, July, and August. The

Jan 8, 1919

By Robert R. Walden, LaMont West

KENTUCKY'S first acid-grade fluorspar flotation mill, shown in Fig. 1, was placed in operation Aug. 1, 1952, by the Pennsylvania Salt Manufacturing Co. at Mexico, Ky. During 1951 a critical shortage of acid-grade fluorspar developed and it became necessary for the company to produce part of its fluorspar requirements. In 1951 the company purchased the Crider and Lennen metallurgical fluorspar mill and an adjacent stockpile of tailing at Mexico, Ky. The tailing, assaying about 26 pct calcium fluoride, originated from log washer and jig mill concentrators in the area. As the mill did not have a fluorspar dryer or convenient rail facilities, the company leased the Burleson concentrator at Marion, Ky., where these facilities were available. At Marion, Ky., on the Illinois Central Railroad, dry acid-grade fluorspar is transported direct to the company's Calvert City, Ky., hydrofluoric acid plant.

Jan 5, 1954