Search Documents

By R. M. Hudson

Equilibrium constants have been determined for the jeaction C (in steel) + H2O = CO + H2 as a function of carbon content (0.013 to 0.74 ujt pct) and temperature (1200° to 1800°F) by using a flow system in which the water-vapor content of various gas mixtures containing hydrogen, carbon monoxide, and nitrogen was systematically controlled. The equilibrium partial-pressure ratio K1 = PcoPH2/PH2O was obtained for two low-carbon steels and four Fe-C binaries from a series of runs made at each temperature. By comparison of Ki with the analogous ratio for the reaction C (graphite) + H2O = CO + H2, the activity of carbon in steel (ac) was comDuted for each temperature and carbon content studied. From these data values of the equilibrium constants for two other carburization-decarburiza-tion reactions of importance were estimated. The chemical compositions of the two steels and four Fe-C binaries used are given in Table I. Specimens of Steel E were cut from a 0.035-in.-thick commercially box-annealed and temper-rolled lot of a low-carbon low-metalloid steel. Steel F was a commercially hot-rolled rimmed steel that was cold-reduced at the Laboratory to a 0.059-in. thickness. Fe-C binaries A, B, C, and D were vacuum-melted and poured, hot-rolled, pickled, and cold-reduced at the Laboratory to furnish specimens 0.035 in. thick. Sheet specimens were cut from all lots to approximately 3/4 by 3 in. by gage and were vapor-degreased with trichlo-roethylene and weighed before heat treatment. Heat treatments were carried out in a hinged-top Hevi-Duty electric furnace with a Vycor-glass tube. When the furnace was at the desired

Jan 1, 1965

By Joseph B. Umpleby

PROGRESS in the petroleum industry in 1929 has been characterized by outstanding accomplishments in the fields of new discovery of supply, economic control of production, increased efficiency and reduced costs of recovery, and lowered costs and greater flexibility in manufacture. Resources have been developed in an outstanding degree in the Kettleman Hills. California, the Oklahoma City field (which adds a large potential area in central Oklahoma), the discovery of Woodbine sand production in East Texas, and the discovery of Wilcox sand production in west-central Kansas. Engineering technique has progressed both along the lines of development and production, with a net result that costs have been reduced and extraction increased in notable degree, although it is impossible to give a close measure of either. In the field of re- fining crude oils variations to the end of promoting reduced cost and greater flexibility has been more important than genera! acceptance of innovations in practice.

Jan 1, 1930

By D. R. THOMAS

GENERALLY speaking, the production of other metals in Mexico fluctuates with that of silver. The first commercial discovery of mineral was in Taxco, Guerrero, in 1552. Five years later, the patio process was introduced at Pachuca, by Bartolome de Medina. In 1884, the main line of the Mexican Central R. R. was completed and a few years later, the National railway. In 1907, the patio process, after 350 years of successful operation, was replaced by cyanidation. Soon after the completion of the railroads, smelters were built at various points and provided means of treating ores that could not be treated by any of the processes existing at that time, such as patio, lixiviation, or pan amalgamation. As a result, a number of mines were developed along the railroads and even far \ out in the mountains. In order to facilitate the shipment of this ore to the smelters, purchasing agencies were established, which for a time were very profitable; most of these agencies are now permanently closed.

Jan 1, 1921

By John Treweek

FOR many years the Homestake Mining Co. has devoted serious attention to the elimination of accidents, and ground is steadily being gained in this direction. In accident prevention work it is line-plunging with perfect teamwork and not the spectacular forward pass that brings progress toward the goal. In both surface plants and under- ground workings we regard "good housekeeping" as a first requisite for safety as well as efficiency. Under this term are included all types of safety guards and protective devices as well as cleanliness and orderliness it working places. Perhaps the most important factor in safety work is to arouse and maintain employee interest. The general morale and contentment of employees is of particular importance.

Jan 1, 1938

By Robert H. Leach, C. H. Chatfield

This paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in conlmercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordaq4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. Analysis of Steeling Silver Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same ana,lysis as our sterling. The first authentic record of the establishment of a standard alloy is during the reign of Henry I1 in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

By L. Dr. Edeleanu

CRUDE petroleum is a mixture of various groups of hydrocarbons and some bodies containing oxygen or sulphur. These constituents possess properties differing considerably one from another and the proportion in which they are contained in the crude oils is also very different. Owing to this complicated composition the practical use of crude petroleum is much restricted. For example it is sometimes used as a liquid fuel. But its employment in this way is uneconomical because various valuable qualities of the individual constituents are not made use of. The rational utilization of petroleum can only be accomplished if the various groups of hydrocarbons are separated. The mixture of hydro-carbons present in the crude oil must be split up in such a way that the hydrocarbons are divided into various groups having certain predominant characteristics and uses. To accomplish such a separation is the aim of the technical refining of petroleum. ORDINARY REFINING BY DISTILLATION AND CHEMICAL TREATMENT Hitherto this has been accomplished by two processes, namely, fractional distillation and chemical treatment of the distillates obtained. Distillation Process The process of distillation consists in the separation of the constituents of petroleum into various fractions, the boiling points of which lie within certain defined limits. The fractions so separated possess certain special qualities in common, which enable them to be applied for specific purposes in practice. For example, we have the fractions known as benzene, illuminating oils, heavy oils, lubricating oils, etc.

Jan 9, 1914

By O. Chanute

all of' level atid grade curve excepting Nos. 897, 898, 899, and 900, because of the impossibility of grouping them in the same nlonner, no two Iraving the chemical composition and physical prnprtiw as tho only v:iriubles. Phosphorus ~tnits have been taken to show the relatia h:wdnes. Of these 16 groups, 10 decidedly indicate slower wear firr tile harder rail. Of the remaining 6 groups, three (groups 2, 9, and 15) come well within the limits of error (.25 pound per yard) inherent in the palculation of the data as pointed out by Dr. Dndley; they catrnot, therefore, be considered tls exceptions. Group 2 and 15 arc but little outside of the limita of error. Rail 923 of group 9 is obviously abnornlal. This is probahly due to its being overheated, which the chemical analysis shows might easily be the case, and which the physical tc~ts and its low specific gravity tend to c-nfirm. We inry say, then, thnt 13 of these 16 groups fairly indicate, if they do not definitely point out, th:kt, under the same condition% tbe harder rail gives the slower wear. Of course, these comparisons are too few to enable us to arrive at positive ~?o-nclusions; but indications thus obtained are, I believe, fir more vsluitblc and tresttvc~rthy than those fhzt averages rvottld give us, mnde up from any ~lumhr of rails under intloy difi~rcal, conditions. Finally, it, seems to me, that the conclusions arrived at earlier in my remarks, together with, and confirmed by the last, show strong evidence that, under the same conditions, the harder rail will givc the slower wear. 0. C~~anute, New York CITY: We are very much shlipl, 1 ant sure, to Mr. Sandberg for his paper upn " Rail Ryaifications and Rail Inspertion in Europe." We have in thp United States bithhrto Been inspecting mils sonlewl~at haphazard, and we ore glad to gtbt tfie results of Mr. Sandberg's long experience. We recognize that he was an)ong the first, if not the very firwt, to iipply mare rittional and scientific rules to the designing of irou rails., niora recently, to adapt tlitve rules to the clesigtting of steel I':I~]R, to conform to the oapaljilities and rqniretnento of this new n1:ttcrial. Although we have generally adopted, in this country, sectinns for hteel rails which marly of our railway men think even bottar than those of Mr. Snlldlmrg, he is neverthelees the Ieat3er in foot.iito11~ we have followed ever since it has been est~blished

Jan 1, 1881

By William Campbell

FiRst I must express my deep appreciation for the honor of being privileged to give the Howe Memorial Lecture this year and at the same time my feeling of inadequacy to do justice to the subject. The first Howe lecturer was most fittingly, Professor Sauveur, his contemporary and friend, and the subject was beta iron. Last year the second Howe lecture was delivered by Dr. Mathews, one of his most distinguished pupils, who spoke on austenite. This year, the Howe Professor of Metallurgy was chosen to deliver the third annual lecture, and the subject ought to be martensite. No one but Professor Sauveur could have brought to life what was considered by many to have been dead and buried, and he so persuasively and convincingly proved to us by his experiments the existence of something that the followers of that new cult "X-Ray and Crystal Structure " would have us believe is simply alpha iron. And Dr. Mathews from his wide practical experience was so easily able to convince us that austenite was not only the most wonderful of the iron-carbon series, but that it was the wonder alloy of the future. If I were to follow in the footsteps of my distinguished predecessors, I would talk to you about martensite. But when I had planned this lecture, I found that I was writing about Professor Howe and his work and his influence on the science of metals of today, and that martensite had become the secondary theme. And when finally I was obliged to choose a title, I remembered that it was in 1901 I came from Roberts-Austen with a letter of introduction to his very dear friend, Henry Marion Howe, at the Columbia School of Mines, to continue my work at the next bench to Dr. Mathews. Since then a quarter of a century has gone by, and during that time all branches of science seem to have been remade, so great has been our advancement in knowledge and discovery. And now that Metallography has finally established its place as an important branch of science, with its own textbooks and literature, I would like to review what seem to me to be the most important advances we have made in the last 25 years. To do this, I would start with Howe's "Iron, Steel and Other Alloys," and end with Jeffries and Archer's " Science of Metals." In the preface of the former, Professor Howe wrote: My warmest thanks are due to the friends who have aided me with their counsel and knowledge. In particular, let me thank most sincerely Prof. Margaret E. Maltby

Jan 1, 1926

By Cornelius F. Kelley

EVERY man connected with the mining industry should take a significant pride in the fact that he belongs to an industry and to a profession that, from the beginning, has been constructive. The miner digs his ore and he gives the metal to art, to industry, and to commerce. The nature of our business is destructive only in that we deal with a wasting asset. That should be a source of great pride to those who belong to the profession. But unfortunately, the product of our mines, our smelters, and our re- fineries does not always go to constructive purposes. There are times when, in the administration of the affairs of men, our product chiefly goes to purposes which are destructive. When we look upon the panorama of horror that is being enacted throughout the world today, we wonder whether any effort toward the development of civilization and culture and education and well-being has been worthwhile. We are appalled to see the things that have been developed, through the application of science, toward progress and efficiency, now used for the catastrophic destruction of those things which are the most valuable that man has built. We must find hope that this is but an episodic thing; that it must, in the infinite wisdom of the Almighty, usher in a period of peace and progress, of civilization and development that will make man's existence upon earth worthwhile.

Jan 1, 1941

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By Andrew Fletcher

AS good health is the most important asset in life, the development of healthful conditions should be the one common meeting ground of agreement between management and labor. Health should not be a subject to be pulled apart, shoved around, or bargained about. Differences of opinion may exist in the procedure and techniques employed in approaching the goal of maintaining the health of workmen, and in the method of increasing the ultimate profit of the employer by improved working and living conditions. Such matters are doubtless appropriate subjects for discussions between the interested parties, but techniques are only tools. If an employer fails to remedy a hazard or a menace which contributes to poor working condlions, this constitutes a legitimate grievance. It should not be necessary, however, nor is it desirable that fundamentals of health maintenance become matters of collective bargaining, any more than should the principles of management and engineering. I have been especially concerned during the last few months with the propaganda in collective bargaining negotiations throughout the country for including in union contracts a given number of days of sick leave with pay. We all

Jan 1, 1946

By L. O. Howard

WHAT was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyère line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Falls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. .About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to handle the total output of copper in these small shells until the standard. Great Falls converters were substituted in June, 1914.

Jan 9, 1916

By L. O. Howard

What was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyhre line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Palls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to "handle the total output of copper in these small shells until the standard Great Falls converters were substituted in June, .1914.

Jan 1, 1917

By Ogden Tweto

The classes of ore deposits in the mountain province of Colorado that have been the most productive in the past and that offer the greatest promise for the future are: (1) disseminated or stockwork molybdenum deposits associated with Tertiary stocks; (2) combination precious- and base-metal veins in Tertiary volcanic rocks; and (3) base-metal replacement deposits and veins in Paleozoic sedimentary rocks. Veins in Precambrian rocks, including precious metal-bearing sulfide veins, gold-silver telluride veins, and tungsten veins, have been mined extensively in the past, but their aggregate output has been far subordinate to that of the groups named above, and the outlook for major output from them in the future is poor. Principal ore deposits of south-central Wyoming are sedimentary iron ores of Precambrian age and uranium deposits in Tertiary sedimentary rocks. Precambrian deposits of several kinds are scattered through the mountains of both states. The most promising of these, based on present indications, are vanadiferous titaniferous magnetite in southern Wyoming and southwestern Colorado and thorium-niobium rare-earth deposits associated with alkalic intrusive complexes in Colorado. Most of the mining districts of Colorado are in the Colorado mineral belt, a generally narrow but somewhat irregular belt that extends northeastward across the north-trending mountain ranges and the north-northwest trending geologic grain of the state. The belt is characterized by intrusive rocks of Laramide and younger age and by ore deposits, and it occupies environments ranging from Precambrian crystalline rocks through Paleozoic and Mesozoic sedimentary rocks to Tertiary volcanic rocks. Two ages of intrusion and ore deposition recently have been recognized in the mineral belt. One is Laramide (late Cretaceous and early Tertiary), and the other is Oligocene. As interpreted herein, the major replacement deposits and most of the sulfide vein deposits in Precambrian and sedimentary rocks are Laramide in age, and the molybdenum deposits, the tungsten and the gold telluride veins in Precambrian rocks, and the precious- and base-metal veins in volcanic rocks are Oligocene in age. In general, the Laramide deposits are mesothermal in aspect, and the Oligocene deposits are principally epithermal. The existence of two mineralization stages, in considerable part characterized by different suites of metals, has many applications in exploration.

Jan 1, 1968

By C. K. Leith

THE interdependence of nations in regard to mineral supplies has grown apace with the expanded needs of industry, with depletion of reserves, and with advances in technology. This increased mutual dependence raises many questions of foreign economic policy of special importance in our postwar planning. Realization of the urgent need for the development of a general mineral policy broadly based on national requirements led to discussions of the problem between officials of the Department of State and myself, as a result of which it was suggested that I make an informal and unofficial canvass of the views of mineral specialists of the country on foreign mineral policy.

Jan 1, 1946

By Cloyd M. Smith

A FEW years ago, the Ventilation Committee established the practice of presenting one topic each year for discussion at the annual meeting. The practice has met good response on the part of committee members and I suggest that it be continued. The topic chosen for this year, "Underground Anemometry," is a topic which has bothered me for more than 20 years. It seems to me that the coal industry is content to rely on slipshod methods for measuring the rate of flow of air underground, so I prefaced my discussional charge to committee members with the statement that I regard air measurements made in the usual way, with hand held anemometer, as no good. Agreements and disagreements came in from more than a dozen engineers, some of whom are with operating companies, coal and metal; some with manufacturers; others with government agencies.

Jan 1, 1949

By E. H. Mohr

AT the McGill concentrator of the Nevada Consolidated Copper Co., all flotation operations have been carried out in Forrester cells since November, 1926. In respect to cost of operation, the new cell has proved to be superior to the Callow, which it supplanted, and its incorporation in the flow sheet has resulted in a marked improvement in the metallurgy. Before citing the advantages of the new machine over the old, it should be explained that the Forrester has not only replaced the Callow, but it has made possible the elimination of a number of tables as well. When Callow cells were in use, table concentration preceded flotation. The ball mill pulp was elevated, by means of air lifts, to roughing Wilfley tables situated two floors directly above the flotation floor. On an intermediate floor were additional tables which cleaned the concentrate from those above. The finished table concentrate constituted approximately 60 per cent. of the total mill production, and contained about 40 per cent. of the recovered copper. The table tailings were returned to the classifiers, the overflow from which went to the flotation cells and the oversize to the ball mills. As soon as the Forrester cells were installed, this tabling operation was discontinued. The ball mill pulp now discharges into the classifiers direct, without the intermediate tabling. It was impracticable to employ the present flow sheet when Callow cells were in use, for the reason that unless the greater part of the heavy mineral was first removed, it accumulated on the mats and adversely affected the flotation operation. By tabling ahead of flotation, it was practicable to maintain the concentrator at 10 to 20 per cent. greater capacity (depending up on the pyrite content of the ore) than was possible by flotation alone. This was due to the necessity for finer grinding in the latter case. Even though the table concentrates contained only 6 to 8 per cent. copper con- tent, the low smelting costs made it advantageous to operate at high mill capacity, at the cost of low grade of product. STANDARD SECTION EQUIPMENT With the old-flow sheet, a standard section consisted of four ball mills and classifiers, one air lift, 20 roughing tables, 10 cleaner tables, 12 primary

Jan 1, 1928

By E. H. Mohr

At the McGill concentrator of the Nevada Consolidated Copper Co., all flotation operations have been carried out in Forrester cells since November, 1926. In respect to cost of operation, the new cell has proved to be superior to the Callow, which it supplanted, and its incorporation in the flow sheet has resulted in a marked improvement in the metallurgy. Before citing the advantages of the new machine over the old, it should be explained that the Forrester has not only replaced the Callow, but it has made possible the elimination of a number of tables as well. When Callow cells were in use, table concentration preceded flotation. The ball mill pulp was elevated, by means of air lifts, to roughing Wilfley tables situated two floors directly above the flotation floor. On an intermediate floor were additional tables which cleaned the concentrate from those above. The finished table concentrate constituted approximately 60 per cent. of the total mill production, and contained about 40 per cent, of the recovered copper. The table tailings were returned to the classifiers, the overflow from which went to the flotation cells and the oversize to the ball mills. As soon as the Forrester cells were installed, this tabling operation was discontinued. The ball mill pulp now discharges into the classifiers direct, without the intermediate tabling. It was impracticable to ernploy the present flow sheet when Callow cells were in use, for the reason that unless the great,er part of the heavy mineral was first removed, it accumulated on the mats and adversely affected the flotation operation. By tabling ahead of flotation, it was practicable to maintain the concentrator at 10 to 20 per cent. greater capacity (depending up on the pyrite contnt of the ore) than was possible by flotation alone. This was due to the necessity for finer grinding in the latter case. Even though the table conecntrates contained only 6 to 8 per cent'. copper content, the low smelting costs made it advantageous to operate at high mill capacity, at the cost of low grade of product. Standard Section equipment With the old flow sheet, a standard section consisted of four ball mills and classifiers, one air. lift, 20 roughing tables, 10 cleaner tables, 12 primary

Jan 1, 1928

By W. D. B. Motter

DURING the early development of blasting with liquid oxygen explosives the trend of experimentation was towards increasing the effectiveness of the explosive. Its characteristic of becoming inert after evaporation of the oxygen content made a strong appeal from the standpoint of safety, especially with missed holes. It later became apparent, however, with practical use of this explosive, that LOX lacked certain other safety characteristics. As its effectiveness was increased, it became more subject to detonation by impact. The object of this paper is to show the steps taken by one operating company to achieve greater safety in the large-scale handling of liquid oxygen explosives.

Jan 1, 1933

By P. B. Bucky

IN previous publications1 it was shown that a scalar model of any weighty structure, where the stresses produced are mainly due to gravita-tional forces, will behave similarly to its prototype if the model and proto-type material are the same arid the model is placed in a centrifugal field of force (substituted for the gravitational field) which has been increased in the same proportion as the linear model scale is decreased. This principle is now being applied to a study of the behavior of mine structures in an attempt to determine the laws that control them. The importance of using models as a means of solving mining problems has been discussed previously, yet it may be well to reiterate here that this method of research and type of solution have been productive of far-reaching results in other engineering fields, notably those of hydraulics and aerodynamics. Model research is a comparatively cheap and time-saving method of checking practical experience. Up to the present time the best guide to what will happen underground has been the judgment of the man who has observed most and been longest acquainted with the local conditions. His experimental work underground is limited by the elements of cost, time and danger, while failure is seldom permissible. In a model, as in a test tube, all elements that affect the solution of a problem are under definite control. Each element may be varied independently at will and its effects noted. Experimental work on a small-scale model may there¬fore be performed at a comparatively small expenditure of time and money, instead of on a full scale in the mine, where the cost, time, and danger elements are necessarily great. The experiments described in this paper are to be considered as part of a progress report and a continuation of Technical Paper 425. One object of the research program is to make each experiment point the way for further research on that particular phase of the general problem. The results and conclusions presented here are therefore not to be considered as final, but are to be interpreted as

Jan 1, 1933