Search Documents

The captions to Figs. 1 and 2 of the paper by B. J. Parry entitled 'High-strength cold-rolled steels' should read as follows:

Jan 1, 1984

By L. Forsbacka, M. Nakamoto, L. Holappa

Viscosity of the slag is one of the central parameters when producing FeCr in submerged arc furnaces. It contributes to smelting behaviour and reduction kinetics of chromite ore as well as to the Cr recovery by influencing the separation of dispersed metal droplets from the slag. A typical FeCr process slag contains 5-10pct chromium oxides, CrO and CrO1.5. The neural network computation was applied to the evaluation of viscosity for slags containing chromium oxides, and the prediction of viscosity in FeCr process slag was conducted. The main results in this estimation were that the chromium oxides in FeCr process slag lower its viscosity, and that the effect of CrO on the viscosity decrease is greater than that of CrO1.5.

Jan 1, 2007

By M. Wu, X. Zhao

This paper presents an integrated pipeline transport system for thickened coal sludge, which combines pretreatment and pipeline transport with combustion techniques of thickened coal sludge. The pipeline can transport thickened coal sludge with a sufficiently high solids content (about72%?77%) and high apparent viscosity (about 1 000Pa?S?3,000 Pa?S) directly by pipeline having neither use for water nor an addition agent. The transport distance can be as high as 1 000 metres. In particular, the operating principles, key equipment and technical parameters of this integrated system are examined in this paper. The integrated system effectively causes no pollution to the environment because it is completely sealed, and conserves energy over traditional conveyer designs. Keywords: pipeline transport; integrated system; circulating fluidized bed boiler; thickened coal sludge; high solids content

Jan 1, 2007

By Mauri Kauppi, Pekka Niemelä

World HCFeCr production is 6.0 million tonnes. Correspondingly 1.1-1.6 t slag / t FeCr is produced depending on the raw material basis. Essentially all FeCr is produced in submerged arc furnaces, while the role of competitive technologies like DC is limited. In all furnaces fluxes are used to optimize the slag composition. Vital characteristics are smelting point, electric conductivity and viscosity. The main components of FeCr slag are SiO2, Al2O3 and MgO. Additionally it consists of Cr-, Fe-oxides and CaO. Granulated slag and/or classified slag products are produced depending on the production process. The slag products are mainly marketed in road and civil construction purposes but also in producing refractories. Normally crushed and screened slags are produced simultaneously when recovering alloy. The leachate of slag products is low and performance results are excellent. Slag products successfully replace natural sand and macadam. Generation of waste is essentially reduced. Producing and using slag products are described as BAT-technology and it is an essential environmental aspect. Outokumpu Tornio Works produces 320 000 t FeCr-slag/a. This paper deals with formation of slag in smelting process, its chemical composition, physical and structural characteristics, utilization and product specifications as well as environmental aspects. The slag products are standardized and CE marked. Additionally the role of slag in smelting and alloy recovery is reviewed in this paper.

Jan 1, 2007

By Willem Le Roux

Occupational health and safety is regulated by statute and common law. South Africa has, like many other countries, legislated extensively on occupational health and safety. Despite the body of legislation, the common law continues to play an important role as far as it concerns contractual, delictual and criminal liability. Two major Acts regulate occupational health and safety viz. the Occupational Health and Safety Act, No. 85 of 1993 (?OHASA?) and the Mine Health and Safety Act, No. 29 of 1996 (?MHSA?). The MHSA applies to mines and works as defined and related aspects. OHASA applies to other industries but does not apply to employers and workplaces to which the MHSA and certain matters covered by the Merchant Shipping Act, No. 57 of 1951 apply. See section 1(3) of OHASA. 2 The employer?s health and safety obligations in terms of the MHSA 2.1 Section 2(1) of the MHSA provides amongst others, as follows: ?The employer of every mine that is being worked must: (a) ensure, as far as reasonably practicable, that the mine is designed, constructed and equipped: (i) to provide conditions for safe operation and a healthy working environment (ii) ... (b) ensure, as far as reasonably practicable, that the mine is commissioned, operated, maintained and decommissioned in such away that employees can perform their work without endangering the health and safety of themselves or of any other person?.

Jan 1, 2011

By S. Durapraj, R. T. Masethe, U. Maqina, A. C. Adoko

This study investigates seismicity and rockburst control within the Merensky Reef and UG2 orebody of an intermediate-depth platinum mine located in South Africa's Bushveld Complex. Utilising a mine-wide seismic monitoring system, over 1,900 seismic events were recorded between April 2023 and May 2024, revealing complex seismic patterns driven by mining-induced stress changes. The largest event, with a magnitude of ML 2.0, underscores the seismic risks associated with mining at increasing depths. Key findings include the spatial and temporal variability of seismic events, with high seismic activity observed near pillars and geological structures. A significant portion of events correlated with pillar and foundation failures. Moment tensor analysis identified dominant failure modes, such as stress-driven fracture closures and dynamic pillar failures. To mitigate risks, the study emphasises advanced support system redesign and rockburst risk assessment using the rockburst damage potential (RDP) method. The research highlights the importance of monitoring, geotechnical compliance, and adaptive designs in enhancing safety and reducing seismic hazards in underground mining operations. The study applied the RDP framework, classifying damage across R1 to R5 scales, where most instances fell into low-risk categories (R1 and R3), indicating minor to moderate damage. However, data limitations and the tabular stoping method's complexity led to inconclusive results, highlighting the need for more robust data and customised risk assessment tools. Despite these challenges, the RDP approach provided valuable insights into rockburst mechanisms and the effectiveness of existing support systems.

Jan 12, 2025

United Kingdom mineral statistics 1977. Home, D., Squirrell, H. C., and Venkatesan, J. (compilers). London, Her Majesty's Stationery Office, 1978. 156 pp. £10,25. Copper mining and management. Navin, Thomas R. University of Arizona Press, Box 3398, Tucson, Arizona 85722. ISBN 0-8165-0586-1. 426 pp. Illustrated. Price Metal statistics 1967-1977. 65th edition. 1978. Metallgesellschaft AG, Reuterweg 14, D 6000 Frankfurt am Main, Fed. Rep. of Germany. 382 pp. Illustrated. Coal mine ground control. Peng, Syd S. John Wiley & Sons. ISBN 0-471-04121-1. 450 pp. Illustrated. £19.75 clothbound. Associate Professor and Chairman of the Uranium supply and demand: Proceedings International Symposium, London, July 1978. Spriggs, Michael J. and Casteel, Kyran D. (editors). Mining Journal Gemorfologiesewoordelys/Geomorpho logical vocabulary. Van der Merwe, J. S., en De Villiers, A. B. (samestellers).

Jan 1, 1979

By H. Lagendijk, I. J. Reinecke

Mintek was contracted by Oriel Resources plc in 2004 to conduct a preliminary assessment study on smelting ferronickel from the large but relatively low grade Shevchenko nickel ore deposit in Kazakhstan. A detailed feasibility study (?DFS?) was awarded to Bateman BV following promising results from the preliminary assessment study (?PAS?) and small-scale pilot plant test work. As part of the DFS, a total of 450metric tons of ore was collected from three different locations in the deposit and shipped to Mintek. After sampling, the bulk sample was prepared for smelting. This comprised crushing, screening and calcining with each step done separately for the three different lots. The chemical composition of the ore from the deposit is relatively high in silica and therefore falls out of the MgO to SiO2 range that is normally processed by pyrometallurgical means to produce ferronickel. The main objective of the testwork was to demonstrate that a method could be found and successfully applied to smelt these siliceous ores and produce an acceptable nickel-containing alloy. A 2-m ID DC arc furnace was installed with a twin-cathode (electrode) configuration to replicate the proposed commercial-scale furnace and also incorporated an advanced design of water-cooled copper panels in the lower furnace sidewalls to withstand the aggressive nature of the high SiO2-containing slags. The reductant used was a high-volatile coal from Karaganda in Kazakhstan. The reductant addition was adjusted to achieve a 90% recovery of nickel. In the assessment of the process metallurgy, some deviation from equilibrium conditions was observed. This deviation is ascribed to the intermittent existence of a smelting bath partially covered with feed during the testwork. Optimization of smelting conditions should result in the metallurgy (slag metal equilibrium) being closer to the theoretical predictions and make the production of a 20% nickel alloy possible at 90% nickel recovery. The solution for the successful processing of these siliceous ores was found in the attainment of the necessary operational stability through the control of arc length, operating temperature, open-bath smelting conditions and flux additions of up to 10% dolime for the most siliceous of the three ore types. The test work carried out by Mintek provided the basis for the process flow sheet and engineering design of the DC arc smelting furnaces for the Shevchenko Nickel project.

Jan 1, 2007

By E. M. Bloomfield, C. A. Jermy

Geotechnical tests were carried out within an area of the coastal sand dune cordon of northern KwaZulu-Natal which is currently being exploited through mining of heavy mineral sands. In situ and laboratory tests were carried out to assess the density, strength and stability of the dune sand material before and after mining. The most stable combination of sand (>63µm) and fines(<63µm) material was determined as well as the effects of compaction on the strength and permeability of the sand dune samples. In situ DCP and density tests showed that the sand dunes fall in density immediately after mining has taken place. However, settlement of the dunes occurs with time and the density increases within the top 2 metres, and particularly once the dunes become re-vegetated. Laboratory tests carried out showed that the dune sand with between 20% and 30% added fines had the highest shear strength and dry density, but the permeability was shown to decrease steadily with increasing fines up to 40% fines added. The addition of fines would result in steadily increasing water flow problems. Compaction of the dune sands was shown to significantly increase the density and the shear strength, but with a corresponding dramatic decrease in the permeability of the material. Slope stability analysis carried out on models of the dunes with increasing fines showed that the addition of fines increases the stability of the dune sands up to a peak of about 30% fines added, and compaction further increases the stability of the dune sands. Despite the benefits of compaction on the stability of the tailings dunes, the loss of permeability is thought to outweigh the benefits as well as the high costs involved. The stability of the tailings dunes greatly increases after re-vegetation. Compaction and densification of the tailings dunes may be necessary within the top 2 m interval if large-scale construction takes place on the sand dunes. Petrographic analysis was performed to understand the granular interactions of the sand and fines fractions, and the effect of the in situ weathering of the dune sands on the stability of the sand dunes. As the fines contents increase the gaps between the sand grains are filled, until a point where the percentage of fines begins to push the sand grains apart.

Jan 1, 2003

By M. Matabane, T. Khati

"Accurate delineation of the contact between a kimberlite pipe and country rock at production level depths is a challenge due to limited geological data. Geological information is obtained from widely spaced diamond core boreholes which are drilled either from surface or from higher mining levels within the pipe. Kimberlite pipe/country rock contacts are notoriously irregular and variable, further reducing the confidence in contact positions defined by the drill-holes. At Finsch Diamond Mine (FDM), the opportunity arose to further improve the confidence in the contact positions relative to the planned slot (end) positions of each sublevel cave tunnel during the development stage of these tunnels. As a result, the accuracy of the 3D geological model has improved.The use of diamond drill core for this purpose is expensive due to site establishment requirements. The lengthy time taken during site establishment also delays the development of tunnels and support cycles, thereby extending the completion dates. FDM has reduced delays during development by adopting percussion drilling, in conjunction with gamma ray logging. The S36 drill rig is mounted on a moveable platform and does not require a costly and lengthy site establishment. The holes are generally drilled (0°/flat) on grade elevation, and these holes could also be drilled from the rim tunnels (developed in waste) into the kimberlite pipe. A single-boom production drill rig is normally used to drill holes about 20 m in length.On completion of the contact delineation drilling, gamma logging of the holes is conducted using the GeoVista geophysical sonde (or probe) to log the natural gamma signature of the dolomite/ kimberlite contact. The advantage of this tool is that the readings are continuous within centimetre intervals, and due to contrasting characteristics between kimberlite (rich in clay minerals) and dolomite, the contact position can be determined accurately. The better definition of contact positions also adds value to tunnel stopping distance in terms of developing the tunnel’s slot at the optimum distance from the contact (easier blasting of longhole rings, avoidance of contact overbreak and premature waste ingress, and other matters relating to extraction of ore from these tunnels). This method is highly successful and has reduced development costs (on-time completion), improved definition of the pipe’s contact position for geological modelling, improved blast design, and mitigated early waste ingress by maintaining the contact’s integrity."

Feb 1, 2019

By John E. Leitch

The cost of corrosion as measured by such cost components as the renovation or replacement of coated steel, or the use of expensive coating systems on steel, is considerable. Extrapolating from figures for the USA would place the overall cost of corrosion for South Africa as a figure of the order of magnitude of something over 1% of the GNP. This is a sizeable amount, of which costs associated with atmospheric corrosion would be a significant proportion. The corrosivity of an atmosphere can be defined as the ability of the atmosphere to cause corrosion in a given metal or alloy (International Standards Organization [1]). The ISO Standard 9223 specifies the key factors in the atmospheric corrosion of metals and alloys, and defines categories of corrosivity on the basis of these factors. Prior to the publication of that ISO standard, Callaghan published the results of his twenty-year exposure programme and his excellent corrosivity map of Southern Africa [2]. The present author published updates of the corrosivity map in 1999 [3] and again in 2003 [4]. The summary of the individual areas of corrosivity around Southern Africa was published in the latter paper, and is reproduced here as the following TABLE 1. Of significance in TABLE 1 are the numerous regions of very high corrosivity (C5 or beyond), particularly the rural West Coast shoreline, the North East Coast (KZN) shoreline, and the coastal cities Cape Town, Durban and Richards Bay. The corrosivity map as published is obviously based on much extrapolation as only a small number of points have been measured. During the past three years further measurements have been made, mostly however at the same sites in order to give greater reliability and to monitor long-term trends with changes in pollution. These two aspects are incorporated in this update. There has become available a greater amount of air pollution data for centres in South Africa than was the case some years ago. In this present paper the pollution data are used to extrapolate the corrosivity over areas where little or no direct corrosivity measurement has been made. This methodology is described in ISO 9223.

Jan 1, 2006

By J. D. Steenkamp, J. Muller

"Excavation of an industrial-scale submerged arc furnace, utilized in the production of silicomanganese, identified two high-wear areas in the refractory lining: the tap-hole, built with cold rammed carbon paste and SiC bricks, and the hearth, built with cold rammed carbon paste. To obtain insight into the potential causes of wear, thermodynamic calculations were conducted on eight sets of data, obtained for seven furnaces on three plants based in South Africa. FACTsage software and associated databases – FACTPS, FToxid, and FSstel – as well as the Mn-Fe-Si-C database of Tang and Olsen (2006), were applied. Theoretical indications are that chemical reaction between carbon refractory and slag, as well as dissolution of carbon and SiC refractory in metal, contributed to tap-hole refractory wear; and dissolution of carbon in metal contributed to hearth refractory wear. IntroductionDuring the excavation of a 48 MVA submerged arc furnace (SAF) used for silicomanganese (SiMn) production, it was found that the taphole and hearth were high refractory wear areas (Steenkamp, 2014). In both these highwear areas, carbon-based cold ramming paste formed the hot face refractory lining (crucible). The wear profile of this SAF is presented in Figure 1.The hot face refractory lining was formed by cold ramming of high-grade carbon ramming material. This material consisted of 50–70% anthracite, 15–25% graphite, 6–12% resin, 2–7% tar, 1–5% clay, and 1–5% alumina. The tap-hole was built using SiC bricks, consisting of 75% SiC, 23.4% Si3N4, 0.3% Fe2O3, 0.3% Al2O3, and 0.2% CaO.In the tap-hole area, the wear of the SiC refractory material was estimated at 0.4 t, and that of the high-grade carbon ramming material, at 1.9 t (Steenkamp, Pistorius, and Tangstad, 2015). The amounts of slag and metal tapped during six years of operation of the tap-hole (September 2007 to April 2013) were estimated at 33 088 t (Steenkamp et al.,2015) and 41 360 t, respectively."

Jan 1, 2016

By B. Mienie, J. F. Morrison, C. H. Wyndham, M. J. Martinson, N. B. Strydom

Contribution to discussion M. J. Martinson (Associate Member)*: Application of the simple selection test mentioned in the penultimate paragraph of the paper (reference to a more detailed description of the test would not have been inappropriate) should assist South African mining engineers to make more efficient and possibly more humane use of available labour. The authors mention that the test &apos;is in use in the gold mining industry&apos;, and it would be interesting to know the extent of this usage in terms either of number of mines or as a percentage of the total number of labourers employed on &apos;heavy&apos; tasks. The paper would have been of greater interest had the authors attempted to relate their findings to the statistics of labour usage in gold mines, members of the Chamber, and to the &apos;heavy&apos; tasks in particular. On this the authors confine themselves in their Introduction to the somewhat ambiguous statement that &apos;A relatively high proportion of the 360,000 Bantu mine labourers are employed underground on manual tasks&apos;. To appreciate the practical significance of the authors&apos; work one needs a detailed breakdown of the underground labour force by occupations, together with estimates of quantities such as: (a) total stope and development tonnages moved manually per shift: by shovelling by shovel/tram by tramming together with distances and any other relevant data; (b) theoretical energy expenditures required to accomplish (a); (c) actual energy expenditures required to a accomplish (a); (d) energy theoretically available to accomplish (a) based on 50 per cent of the total maximum oxygen intakes of the labour force allocated to these tasks. Analyses of this sort on an industry basis might demarcate the more promising areas for detailed investigation. Stress is often laid on the need for increased mechanisation to increase stope productivity, but it may be questioned if enough is known about the characteristics, performance and potential of our underground labour force to warrant blind acceptance of stope mechanization as the industry&apos;s panacea. Provided that health and safety are not compromised, the ultimate yardstick for assessing any form of stoping is profitability; obviously the industry must investigate very thoroughly any form of mechanization which might reasonably be expected to increase profitability, but it should also be remembered that a radical overhaul of existing systems-which have after all evolved by trial and error over the past 75

Jan 11, 1968

By G. Westcott

Impala Platinum, the second largest platinum producer in the world, is embarking on a major expansion strategy to increase its platinum output from 1.95 moz to 2.8 moz by the year 2008. The smelter complex, situated in Rustenburg, will undergo substantial modifications, and will require a solution to the capture and treatment of the smelter off-gases and dust produced during smelting and converting operations. One of the solutions explored was an integrated approach, where all the off-gases from both the primary smelting electric furnaces and the converter operations are routed to a large central gas cleaning and double catalysis, double absorption acid plant. In-line sulphur burning, utilizing a highly flexible LURO1spin cup burner with a turn down ratio of 50%, ensures that the acid plant operates independently of operating conditions at the smelter complex.

Jan 1, 2007

By F. H. Abd EL-Rahiem

A selective dispersion process is presented and the work carried out to find optimum process conditions to minimise the colouring material in ground calcium carbonate (GCC) is described. The feed material is the overflow product from a hydrocyclone which results from using a Denver Attritioning machine with semi-autogenous grinding for one hour and a 1:1 ore/water ratio. By using sodium silicate (SS), with pH 9 and pulp density 5%, the iron content (as colouring impurities) is decreased from 0.21% in the original concentrate to 0.12% in the final concentrate. The degree of whiteness reached is improved to 85% from 63% in the original material. However, by using hexametaphosphate (SHMP) at pH 10 at the same pulp density, the iron content decreased to about 0.073% and hence the whiteness degree increased to about 96%.

Jan 1, 2004

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article the following hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By S. R. Sankaranarayanan, T. Sowmya

Slags and fluxes used in metallurgical processes are typically made up of oxides (especially silicates), with additions of fluoride and carbonaceous matter. Despite the efforts made towards understanding the role of slags in various processes, little information is available on the structure of these slags. Tools such as X-ray diffraction, spectroscopy, and electron microscopy could be used for this purpose. This paper is based on an ongoing spectroscopic and structural investigation of slags and related materials. Spectroscopic studies of various commercial slags (predominantly ferrous), ores, glass and related materials, covering a wide range of compositions, have been carried out to understand the structure. The infrared spectra were recorded, predominantly, using FTIR spectrometer (Bruker IFS 66U) spanning 4000 to 100 cm-1using the KBr pellet method. The resolution was typically 4 cm-1. The spectral outputs have been compiled in terms of bands present (corresponding to different bonds) and then compared with the typical bands expected for such bonds. Efforts are in progress to identify the trends with respect to the chemical composition?for example, the effects of SiO2, Al2O3, and non-bridging oxygens. Data obtained so far indicate some trends such as (i) a shift in the Si-O band (969 to 1099 cm-1) towards a higher wave number with increasing silica content (almost 2 to 92 weight percentage) and (ii) further strong shifts as a function of the alumina content. These are being further investigated structurally and in terms of chemical composition/parameters. Keywords: slags, silicates, structure, spectroscopic analysis, shifting of bands

Jan 1, 2004

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article thefollowing hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the of chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By R. Uwaoma, A. Goosen, R. Matjie, K. Mphahlele, J. Bunt

Coal properties that are associated with wear and damage of grinding equipment during pulverization prior to combustion were investigated. A South African Highveld feed coal and its beneficiated fractions were crushed to <1 >0.25 mm particles for the grindability tests. These particles were milled and screened into <75 μm and >75 μm fractions, which were analysed by different techniques to establish a correlation with the conventional Hardgrove Grindability Index (HGI). The <1.5 g.cm-3 float fraction, which contained 93 vol.% (mineral matter free) total -macerals,9% kaolinite, and had the lowest HGI (57) (hardest to grind) was pulverized for 15, 30, 60, and 120 minutes for particle size distribution analysis. This analysis indicated that the content of <75 μm particles increases with increased grinding time. The >1.9 g.cm-3 sink fraction, with the highest HGI (76), 44% kaolinite, and 20 vol.% total macerals, was ground easily to generate the highest proportion of <75 μm particles. Based on higher correlation coefficients (R2 = 0.77–0.91), the ash yield, mineral matter, petrographic composition, and fixed-carbon have significant effects on the HGI. Conversely, the inherent moisture and total sulphur (R2 = 0.48–0.62) have only minor effects on the HGI. Results from this investigation could be implemented in the preparation of a suitable pulverized fuel with little equipment wear, as well as utilizing mineralogical and petrographic compositions. Finally, the effect of microlithotypes and maceral types in South African feed coals on the HGI should be investigated in further pulverization and grindability studies.

Jul 5, 2023

By S. Ata, Y. Pan, S. Gautam, G. Bournival

Bubbles play a vital role in flotation, and their properties directly affect the flotation performance. Xanthates are one of the major collectors used in sulphide mineral flotation. It is often believed that their main function is to render the desired mineral surface hydrophobic, which is essential for the mineral particles to attach to air bubbles. This paper takes a systematic approach to assess the influence of potassium amyl xanthate (PAX) at the air–liquid phase and its interaction with the frother in the concentration of range 10–5×104 ppm. Bubble size was measured in a laboratory flotation cell using a photographic technique and the stability of bubbles was quantified in terms of coalescence time -, the time required for a bubble pair produced at adjacent capillaries to merge into a single bubble. Bubble size reduction of up to 26% was observed with increasing PAX concentration in the cell. The bubble coalescence experiments using PAX only showed that the bubbles coalesced quickly at lower concentrations (10–50 ppm), but they stayed extremely stable at higher concentrations (1×102–1×104 ppm). Further experiments were carried out where the concentration of PAX was fixed at 1 ppm and 4- Methyl-2-pentanol (MIBC) concentration was varied. The synergetic action of PAX and MIBC significantly improved the stability of bubbles in the mixed system, and is even compatible with a stronger frother. The results strongly suggest that the role of PAX at the air–liquid phase should be considered in the practice of sulphide flotation. Keywords: Bubble size, bubble coalescence, PAX, bubble stability

Jan 1, 2020