Search Documents

SYMPOSIUM ON THE RECOVERY OF PYRITE The proceedings of the Symposium on the Recovery of Pyrite, held in Johannesburg in June 1969, may be ordered from the Secretary, S.A.I.M.M., P.O. Box 61019, Marshalltown, Transvaal, at the reduced price of R5.00. Papers and addresses presented at the Symposium were: Opening Address by Mr J. K. E. Douglas (President). "The world sulphur position," by W. C. J. van Rensburg (Member). "The South African sulphur position," by D. L. Taylor (Member). "The recovery of pyrite at Government Gold Mining Areas Limited," by R. J. Westwood (Member), G. S. Stander (Affiliate) and H. P. Carlisle (Member). "Recovery of pyrite concentrates from colliery-waste discards-A preliminary assessment," by W. A. Gilbert (Visitor) and E. A. Nugent (Member). "The role of pyrite in upgrading the uranium content of Witwatersrand conglomerate ores by means of the heavy-medium separation process," by D. J. Tutt (Associate Member). "Pyrite recovery by jigs at Durban Roodepoort Deep Limited," by E. J. Dominy (Affiliate), F. Diamond (Affiliate) and A. D. Graham (Affiliate). "The storage of pyrite concentrates," by Joan C. Campkin (Visitor) and P. J. Lloyd (Member). "The flotation plants of the Anglo-Transvaal Group," by L. A. Bushell (Member). "Pyrite flotation with amines and cyanidation of the products," by E. H. D. Carman (Member). "Gold recovery by cyanidation from mill products obtained after pyrite flotation," by P. G. Mrkusic (Graduate), M. Sciarone (Visitor) and H. E. Simonsen (Visitor). "The influence of sulphydryl and cationic flotation reagents on cyanidation of native gold," by K. G. Ashurst (Visitor) and W. P. Finkelstein (Member). "Laboratory tests on the flotation of pyrite from Witwatersrand gold ores by cationic collector," by J. Levin (Member), and M. L. Veitch (Visitor). Closing Address, by Dr R. E. Robinson (Director, National Institute for Metallurgy). INCOME TAX: POST-GRADUATE STUDY COURSE CONCESSION As a result of representations made by the Associated Scientific and Technical Societies of S.A. and the Suid-Afrikaanse Akademie vir Wetenskap en Kuns, engineers and scientists will now be allowed to deduct expenses incurred on post-graduate study courses from their taxable income. The conditions of this concession are set out in section 16 of the Income Tax Act, 1969, which reads as follows: 16. (1) The following section is hereby substituted for section 16 of the principal Act: 16. "Notwithstanding the provisions of section 23(a) and (b), there shall be allowed to be deducted from the income of any person who is a dentist or medical practitioner or practises any profession referred to in paragraph (a), so much as the Secretary may allow of any expenditure incurred by such person in the circumstances contemplated in paragraph (c), if the Dental Association of South Africa in the case of a dentist, or the Medical Association of South Africa in the case of a medical practitioner, or the "Suid-Afrikaanse Akademie vir Wetenskap en Kuns" or the Associated Scientific and Technical Societies of South Africa in any other case, certifies in such form as the Secretary may prescribe that such person- (a) if he is not a dentist or medical practitioner, is the holder of a degree in engineering or allied technology or natural sciences awarded by a recognized university on completion of a prescribed minimum period of study of not less than four academic years or the equivalent thereof and enabling the holder thereof to practise the profession of an engineer or a profession for which advanced and specialised scientific knowledge is required which relates directly to- (i) the development or exploitation of natural resources; (ii) mining or prospecting for minerals; (iii) the production of pastoral, agricultural or forest produce ; (iv) the breeding or care of farm animals; (v) any industrial process; or (vi) the training of specialists in any branch of science or technology connected with any aforementioned profession; (b) has practised his profession for not less than three years; and (c) has incurred such expenditure during the year of assessment in respect of the attendance by him of any postgraduate study course approved by such body to improve his qualifications for carrying on his profession in the Republic". (2) The amendments effected by subsection (1) shall first take effect in respect of assessments for the year of assessment ending on the twenty-eighth day of February, 1970. From this section it is clear that the concession will only be granted if the application is accompanied by a certificate, which certificate must be either signed by the Chairman of Die Akademie or the President of the Associated Societies. In terms of the authority granted such certificates must certify that: (i) the taxpayer concerned has practised his profession for not less than three years; (ii) the expenditure was incurred by the taxpayer during the year of assessment indicated in the certificate; (iii) the expenditure was incurred by the taxpayer in respect of the attendance by him of a post-graduate study course approved by the Associated Scientific and Technical Societies of South Africa or Die Suid-Afrikaanse Akademie vir Wetenskap en Kuns, as the case may be, to improve his qualifications for carrying on his profession in South Africa; (iv) the taxpayer is the holder of a degree in engineering or allied technology or natural sciences, which degree was awarded by a recognized university,

"I have been involved in the refractory industry for many years and at some time or another I have designed materials, tested materials, manufactured materials, installed materials, in fact I have done everything except actually chemically analyzed a refractory material.So I would not even begin to tell you how to analyse a refractory material. I'm sure everyone here knows more about chemical analysis than I do.However you could regard me as a customer with and perhaps the insights I have developed may help in putting the role of chemical analysis in the Refractories into perspective.For a start, let's take a step back and ask why we test refractories. The refractories handbook of the American Foundry Association gives four reasons:1. To determine appropriate specification.2. For quality control, to ensure conformance to specifications.3. To provide special property information not available elsewhere.4. For postmortem analysis to determine property changes in service and provideinformation that can point the way to better service.I want to discuss these points with regard to the role of chemical analysis and in particular the abuse of in house chemical analysis facilities. Let me talk first about detelmining appropriate specifications. Most refractory products are made from alumino-silicate raw materials.The phase diagram for alumino and silica is as follows:"

Jan 1, 2014

By J. D. Flint

The geological conditions in the Vierfontein area ~re such that conventional pillar extraction ~stooping) cannot be practised safely or efficiently. Both the open-end lift and the pocket-and-fender methods of pillar extraction have been tried with little success because of problems with roof control and ground stability. The main reasons for the difficulties are the coarse-grained sandstone roof, local weaknesses in the coal seam, and the rate at which the pillars were extracted. The mine has practised bord-and-pillar mining since it started production in 1952, and considerable reserves of coal are contained in the pillars. As an alternative to total pillar extraction, in which hand-loading methods were practised, a system of partial pillar extraction using mechanized-mining methods ~11"modified goaf-line support has been evolved. These remnant coal pillars (snooks) remaining after partial extraction ofthe pillar, together with the installation of 1,2 m" matpacks and a double line of fullcolumn resin roofbolts, ensure control of the edge of the area that has been mined out (goaf). Where roof conditions preclude the use of conventional pillar-extraction methods, this method holds promise as a safe and efficient alternative for the recovery of coal from pillars and for an increase in the volumetric extraction of the reserves within a mining panel.

Jan 1, 1984

By A. Haines, O. Varaud, I. Baidoo

Abosso Goldfields Limited (AGL) is in the process of developing an expansion of their Damang Open Pit gold mine in Ghana. AGL acquired the Damang mine in January 2002, with SRK participating in the geotechnical investigation and design for the project since 2001. A deep resource drilling program, completed during 2004, intersected an extension of the orebody below the then planned final pit floor. A feasibility study has been completed to determine the economic extraction of this deep ore with an expanded pit shell. The Damang mine is in a stockwork sulphide deposit at the culmination of the Damang anticline. The deposit occurs as hydrothermal mineralisation associated with dominantly east dipping thrusts and sub-horizontal quartz veins. Primary gold mineralisation also occurs in the conglomerates of the Tarkwaian Formation. The geological units consist of steep easterly dipping dolerite, sandstone, siltstone and phyllite beds, with the weathering profile comprising saprolites overlying a relatively thin joint oxidized horizon. It is planned to deepen the current open pit to a final depth of up to 270 m, primarily by the development of a push-back of the eastern and western walls. The edge of the Eastern Tailings Storage Facility (ETSF) is currently located within 80 to 100 m of the crest of the existing pit. The geotechnical design focused on the optimization of the bench face angle and finally recommended a ?Steep Slope Strategy?, involving 24m high near vertical benches. Limiting bench stack heights of 96m at a maximum of 66° were derived from the influence of major structures and the variation in rock mass conditions. The overall slope angles in each pit sector were developed around the requirement for haulage ramps. One of the main design challenges was to optimise the standoff distance between the final pit crest and the ETSF. This process had to consider maximum access to the resource without undue influence on or from the nearby tailings dam. A planned increase to the height of the dam wall was an additional factor in the design. Dewatering of the pit walls was also a major consideration in this tropical environment.

Jan 1, 2006

By Nelson Sánchez

The Los Bronces Development Project (LBDP) was approved in October 2007 by the Anglo American plc Board at a capital cost of some US$1.74B, and is scheduled to be completed by the end of 2010. The project represents a big step forward for the Los Bronces mine since it will increase the treatment rate by 140%, the mining rate by 64% and almost double copper production during the first four years of the project. This economy of scale will also position Los Bronces as a much bigger and efficient mining operation, better prepared to face adverse market scenarios and allowing Anglo to consolidate its position in base metals. The project addressed numerous scope alternatives such as plant capacity vs mine capacity, cut-off grade strategy to maximise value based on the existing flotation and leaching process, cutback strategy, etc. Main infrastructure aspects of the project are as follows: ?Dump area with 2400Mt capacity for waste and low grade material ?Mining equipment: 1 x electric shovel, 12 x 300t trucks, 1 x drill ?Primary crusher: 60? x 89? ?Three new power lines (144MW capacity) ?Grinding plant at 87kt/day nominal capacity (includes a 4.3km tunnel with a regenerative conveyor belt) ?Grinding plant: 1 SAG mill 40? x 25?, 2 ball mills ?Slurry pipeline (52 km from grinding to flotation plant) with five choke stations ?Flotation plant (rougher, cleaning, regrinding circuits and molybdenum flotation). The history of Los Bronces started in 1867 when it was discovered. In 1978 ENAMI (Government company) sold Los Bronces to Exxon for US$112M. The same year a snow avalanche destroyed San Francisco Flotation Plant. In 1979 the plant was rebuilt at 4.9kt/day and from 1979 to 2002 several plant expansions were made up to 54kt/day capacity. In 2002 Anglo acquired Los Bronces for US$1.3B. The 2002 resource and reserve statement showed reserves at 459Mt at 1.02%CuT and resources at 780Mt at 0.80%CuT. The 2007 statement shows reserves at 1,480Mt at 0.67%CuT and resources at 1,644Mt at 0.45%CuT. Defining the size of a plant expansion is the key challenge that any expansionary project faces. The scope of this paper is a general review of the project, describing all the mining techniques that were used to define the best options that maximise value. In this context, a range of plant capacities (from 58 to 230kt/day) combined with a range of mining capacities (from 83 to 166Mt/a) were evaluated in detail, defining for each option a mine plan, Capex and Opex, and cut-off grade strategy for flotation and leaching processes and the associated Net Present Value (NPV) that was used as the selection criteria. The Los Bronces mineral resources potential provides good growth opportunities for the mine beyond LBDP implementation, offering an exciting invitation to continue studying new initiatives that maximise the value of this deposit.

Jan 1, 2008

By W. G. Huang

To recover the coal resources of high-sulphur anthracite in Jincheng Mining Area, underground coal gasification (UCG) of No. 15 seam in Fenghuangshan Coal Mine was proposed. The feasibility of the project was confirmed by investigations of occurrence conditions, coal properties, and roof conditions, as well as experimental studies and theoretical analysis. It was found that UCG technology is appropriate to be adopted in the mining of the No. 15 seam, due to the stable rock conditions, simple geological structure and hydrogeology, the high carbon content of the coal, non-cohesiveness, medium-thermal stability, high ash fusion temperature, and weak reactivity with CO2. Further factors are the characteristics of the immediate roof, which consists of 9.11 m of limestone and mudstone with a compact structure and low permeability, and 4.27 m of dominantly mudstone with low permeability.

Jan 1, 2012

I. Book review Legal and institutional arrangements in minerals development. Edited proceedings of a workshop organized jointly by the VN. Department of Technical Co-operation for Development and the German Foundation for International Development (DSE), held in Berlin in August 1980. London, Mining Journal Books, 1982. Soft, 228 X 149 mm, xi + 223 pp. Approx. R30 + GST. Reviewer: M. J. Martinson 2. New books Strength of metals and alloys (IOSMA 6). R. C. Gifkins (Editor). New York, Pergamon, 1982. Approx. 1200 pp. 3 vols. V.S. $220. Deformation-mechanism maps. The plasticity and creep of metals and ceramics. H. J. Frost and M. F. Ashby. New York, Pergamon, 1982. Approx. 250 pp. V.S. $60. Pressure diecasting, Part 2. The technology of the casting and the die. D. F. Allsop and D. Kennedy. New York, Pergamon, 1982. $ V.S. 27.50.

Jan 1, 1982

The optimization of sample spacing In South African gold mines by J. M. RENDU*, Eng. Se.D., M.S. (Min.) U.S.A. (Graduate Member) A first attempt is made at optimization of sample spacing in South African gold mines. The De Wijs model, which is shown to give a good representation of the geostatistical properties of gold values, is used to analyse the influence of the distance between samples along a stope face on the error of estimation of the stope value. The influence of other factors such as the face advance before resampling, the sample density, and the stope size, is also considered. Practical conclusions are drawn concerning the optimum sampling policy to be followed in various situations, and it is shown that sampling on a regular grid does not necessarily give the best results.

Jan 4, 1976

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By D. Nardini

The need to move towards faster and safer mine development is a key priority in mining houses globally. In addition to this, South Africa faces an array of challenges introduced by labour-intensive operations; hence a study was conducted to look into improving development rates and labour productivity, specifically in the areas where trackbound flat-end development is required. The aim of the study was to propose a method to deliver fit-for-purpose tracked tunnels that advanced at a rate of one blast per end every single working day. A major part of the study was to optimize the selection of an appropriate trackless fleet and mitigate any constraints introduced with the mechanization. This was done by creating scenarios, based on a typical case study, looking into the aspects around safety, mine design, mine activity cycling, men and machine requirements, service installations, and trackless-trackbound interfaces. The case study was based on a deep-level gold mine developing twin headings with connectings; however, with the move to extend and deepen platinum operations it is foreseen that twin end development will become more prevalent due to ventilation, logistical, and other requirements. With the introduction of the trackless mechanized system suggested, development rates of 56 m of system advance are expected (189 m total development), with on an average of three headings and fixed blast times. Scenarios run with multi-blast conditions yield expectations of 75 m/month advance of the system, significantly higher than the conventional performance seen today.

Jan 1, 2012

By C. Ndou, T. Mothupi, H. Mandende

The technological advances in efficient, rapid, and non-destructive hyperspectral core logging systems for systematic mineral mapping have led to the discovery and exploitation of new mineral deposits Hyperspectral imaging in the long-wave infrared range has been recently used successfully to identify various phosphatebearing minerals (monazite, xenotime, and britholite), with limited work on apatite associated with mafic-ultramafic layered intrusions. In this study we investigate the effectiveness of a hyperspectral imaging (HSI) system with long-wave infrared (LWIR) bandwidthsto identify apatite in the Upper Zone of the Bushveld Complex. The accuracy of the HSI results was validated by mineralogical and geochemical data. The two apatite-enriched zones detected by HSI suggesting widespread development of apatite throughout the uppermost 600 m of the Upper Zone. The lower apatite-enriched zone is approximately 40 m thick, while the upper apatite-enriched zone is about 23 m thick, consistent with previous thickness determinations by traditional logging and analytical methods. Spectral mixing observed in the response of apatite is ascribed either to the common association of apatite and olivine in these rocks, or to differences between the spatial resolution of the hyperspectral image and the size of apatite grains. The VNIR-SWIR wavelength region did not show prominent spectral features of apatite. Nonetheless, HSI in the LWIR range is effective in mapping apatite and should therefore be considered as an exploration tool. This research advances our knowledge of the reflectance spectroscopy of REE-bearing minerals, which makes it easier to detect, identify, and quantify REE-bearing silicate minerals by HSI.

Feb 6, 2023

By R. L. Castro

Currently, in several caving operations, the spacing between the drawpoints is determined by consulting Laubscher's design guide (Laubscher 1994, 2000), a methodology based on the gravity flow characteristics of the caved rock. Laubscher's methodology is based upon the height of interaction between adjacent flow zones, but does not allow calculation of primary recovery for a given layout. In this paper the authors present a technical and economic methodology based on the flow that occurs near the drawpoint and the associated development costs to estimate the optimal spacing. The flow model at the drawpoint was validated at the El Teniente mine, which extracts coarse caved rock. To validate the flow model, small-scale simulations using drawpoint clusters were conducted and results compared to extracted grades, marker recovery, and drill holes to determine ore remnants that are part of the production control programme at the mine. The results indicate that primary recovery depends on the height of interaction, which varies with the friction angle of the caved rock and the spacing between adjacent drawpoints. Primary recovery estimations indicate values from 85 per cent to 97 per cent depending on the drawpoint spacing used. Extrapolations were then conducted to estimate the primary recovery for different drawpoint configurations planned to be used in the New Mine Level of the mine. The results indicate that the optimal drawpoint spacing is 32 m x 20 m with a through length of 18 m. The methodology developed may be used to estimate optimal drawpoint spacing for block caving mines under different metal prices and mine cost conditions.

Jan 1, 2012

By G. W. Holl, E. G. Fairon

A review of some aspects of shaft design by G. W. HOLL, Pr. Eng., Associate of the Mine Managers Association of South Africa (Fellow)- and E. G. FAIRON, Pr. Eng., F.S.A.I.E.E., M.I. Cert. M.E.E., M.I.Mech. E., (Visitor) The reasons for the choice of vertical shafts in preference to inclined shafts of comparable capacity are set out, and the conclusion that the former are superior in virtually all circumstances is substantiated. The shapes of vertical shafts sunk during the past sixty years are recorded, and the shapes of those sunk during the past decade are analysed. From this analysis it is clear that circular and elliptical (and quasi-elliptical) shafts are the shafts of the future and that the rectangular shape will conceivably become obsolete. The determination of the size of shaft is discussed and it is forecast that shafts of a diameter of 13 metres and over will probably be sunk without difficulty in the years to come. The depth of the shaft is determined intrinsically by the Mines and Works Regulations applicable to factors pf safety of winding ropes and the design of the winding system. The Blair winder is the most suitable winder for hoisting rock, men, and material from a depth of, say, 3000 metres on an economic basis. Tertiary shafts will, therefore, be unnecessary in future deep-level mining projects at the limit of depth now envisaged. A few other factors relating to shaft design are described.

By P. R. Jochens, D. D. Howat, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace A. A. HEJJA, Dipl. Ing. (Budapest) (Visitor) D. D. HOWAT, B.Sc. (Glas.), Ph. D., F.I.M. (Fellow) P. R. JOCHENS, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. (Member) The iron charged to the basic oxygen furnace at the steel plant of Highveld Steel and Vanadium Corporation has a relatively high sulphur content. Considerable emphasis is therefore placed on the reactivity of the lime. An investigation of the lime used at the steel plant showed that its reactivity had deteriorated considerably both during transport from the supplier (Northern Lime Company) and during storage and handling at the steel plant. The deterioration on the steel plant is the more severe, and is due to hydration and carbonation. Rapid deterioration is a characteristic of highly reactive lime when exposed to the atmosphere. Plant tests showed that the desulphurization efficiency decreases with a decrease in the reactivity of the lime. The addition of slag rich in manganous oxide to the furnace considerably improved the efficiency of desulphurization that can be achieved with limes of lower reactivity and with lime that has deteriorated. A decrease in particle size of lime of lower reactivity greatly increased the desulphurization efficiency. Less lime of higher reactivity is required for the same degree of desulphurization to be achieved. Lime of higher reactivity gives rise to slags with lower ferrous oxide contents and hence the steel yield is increased.

By J. W. van der Merwe, A. S. Bolokang, M. J. Phasha, V. J. Matjeke, C. Moopanar

"Excessive wear rates on railway wheels can result in rolling-stock derailments. If wear is detected early the possible derailments can be prevented by prematurely replacing wheelsets, although the inventory cost and maintenance downtime remain a challenge. In the current study, wheels were introduced and monitored in-service for two years to investigate the cause of excessive wear rates. The wear rates and stresses were calculated for the wheels suitable for a maximum load of 26 t per axle. Microstructural and mechanical properties were analysed. As expected, the general microstructure of all the wheels tested was pearlitic. Although all the wheels complied with the tensile strength requirements, stress calculations confirmed material distortion on excessively worn wheels whereas trial wheels revealed yield strength exceeding the yield criterion. High wear rates observed on the wheels were a result of low yield strength relative to the load per axle. The typical wear mechanism found was due to a combination of rolling contact fatigue and abrasive brake wear. Despite compliance of the wheels with existing requirements regarding material and mechanical properties (hardness, ultimate tensile strength), it is recommended that the yield strength must also be taken into consideration as a critical parameter.IntroductionRailway wheels are used to support the wagon mass and guide the wagon along the tracks (Park, 1974). The wheels and rails must be able to tolerate the applied tangential forces in order to effect wagon dynamic performance and reduce material deformation (Ghidini et al., 1994; RSE_TE_SPC_0045, 2011; AAR M107/M 208 Specification, 2011. Over the past ten years, the South African coal wagon maintenance depot has experienced excessive hollow wheel wear rates on the heavy haul line wheels. The maximum load of Jumbo wagons on the coal line is 104 t, or 26 t per axle. Although the maintenance intervention cycle for wheelsets was two years, between February 2011 and August 2012 some wheels experienced excessive hollow wear. Hollow wear is regarded as wear exceeding 2 mm on the central portion of the wheel tread (RSE_TE_SPC_0045, 2011). This happened despite the fact that these wheels were manufactured and certified according to the requirements of AAR M107/208 standard for carbon steel wheels (AAR M107/M 208 Specification,. 2011) and the local wheel RS/ME/SP 021 standard specification (RS / ME / SP / 021 REV 5 (2013). The AAR standard only specifies a minimum hardness as a required mechanical property and the local standard specifies hardness and minimum tensile strength only. In general, an increase in hardness will improve the rolling/sliding wear resistance of steel. This relationship of hardness and wear resistance was found to be true only in a situation where solid and similar alloys are in contact (Singh, Khatirkar and Sapate, 2015). The sliding wear resistance of a material is usually estimated using Archard’s equation (Liu and Li, 2001)."

Jan 1, 2016

By S. Kok, D. Delport, J. Calitz

Altering the microstructure in order to improve the tensile properties of bow shackles resulted in inconsistency in the fatigue performance. This raises the question whether the inconsistency in fatigue life can be attributed to microstructural changes along the profile of the shackle or to decarburization at the surface. Bow shackles forged from 080M40 (EN8) material were subjected to different heat treatments in order to alter the microstructure. The shackles were subjected to five different fatigue load cases, which represented typical loads experienced at termination points for an overhead power line with a span length of 400 m, with changes in conductor type, configuration, wind, and ice loading. Although the change in microstructure does improve both the tensile and fatigue performance, we found that the depth of the decarburization layer has a greater effect on the high cycle fatigue life of bow shackles than the non-homogeneous microstructure.

Oct 1, 2021

The Annual General Meeting of The South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 18th August, 1982. Mr G. Y. Nisbet (President) was in the chair and declared the meeting open at 16h05. Obituaries President: It is my sad duty to announce the deaths of the following members of the Institute: Honorary Life Fellow J. A. Taylor ; Life Fellows J. Watt and J. J. Cairns ; Fellows J. H. Mortimer, R. R. M. Cousens, H. Clark, S. W. Hill, Dr A. Whillier, and Dr C. M. van H. van Staden; Members F. W. McElroy, V. J. Irsigler, B. J. R. Botha, and E. J. Jackson; and Associate B. V. Robertson. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, please rise and ob¬serve a few minutes of silence.

Jan 1, 1982

By H. M. Wells

The investment decision under uncertainty by H. M. WELLS, Pr. Eng., M.Se. (Fellow) The future outcome of a proposed investment is uncertain at the time the decision must be made to accept it or reject it. This uncertainty can be expressed in the form of a probability distribution. An attempt is made to rationalize the investment decision under these circumstances, especially when the range of possible outcomes extends into both the acceptable and unacceptable domains. A rigorous definition of risk is proposed, and a criterion of risk aversion is developed that forms the boundary between acceptable risk and unacceptable risk (called the loss limitation line). It is shown that this decision criterion can also serve as a quantitative yardstick in the evaluation of various possibilities for 'tailoring' the proposal to mlke it more compatible with the particular financial circumstances of the company concerned.

Jan 4, 1976

Minutes of meeting held at the Moth Hall, Witbank on 13th November, 1969. There were present eleven members: Mr J. Meintjes (in the chair); Messrs I. E. van Aswegen, O. T. Wright, A. W. L. Brereton, A. Bain, J. Brook, P. J. Beukes, C. H. Coxon, B. F. v.d. Merwe, A. C. Hofmeyer, G. E. Carlyon. Six Associate Members: Messrs E. J. Jackson, J. N. H. Pritchard, R. E. Powell, W. Weber, R. Smith, B. T. Hosking. One Student Member Mr M. J. de Beer. Seven visitors. The Chairman reminded members of the intended visit to Barberton. Dr Stander, Director of the National Institute for Water Research, gave an interesting talk, illustrated with slides and a short film, on the conservation and reclamation of water in South Africa. After question time, Mr Hector, Witbank Town Engineer (visitor) thanked Dr Stander. The meeting closed at 7.10 p.m.