Search Documents

By Joseph J. Wallace

1. From the standpoint of known recoverable reserves, the following is the order of importance of the beds: Upper Kittaoning, Lower Kittanning, Upper Freeport, Lower Freeport, Middle Kittaning, Clarion, Pittsburgh, and Redstone. 2. mown measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, me estimated at 1,859 million short tons as of January 1, 1952. Of this, 1,351 million short tons me in beds 28 inches and more thick. Areas in each bed were omitted from the estimates because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By Renpei Yoda

An investigation was conducted to develop columbium alloys with e1evated-temperature strengths higher than those exhibited by more common commercial columbium alloys, and attention was given to improving the oxidation resistance and ease of fabrication. Additions of carbon, aluminum, and chromium were made to some columbium-base alloys, and their effects on workability, recrystallization, oxidation resistance, and mechanical properties at elevated temperatures were explored. The additions were made to take advantage of (1) solid solution strengthening, and (2) precipitation hardening. Three alloys displayed good high-temperature properties with relatively good oxidation resistance at 1,000° C, and tensile strengths from 26,000 to 32,200 psi at 1,400° C. When the properties of these alloys were compared with those of commercial alloys, B-66 and FS-85 (1),4 the outcome was favor-able for the alloys studied in this investigation.

Jan 1, 1967

By Joan C. Biordi

[Composition profiles for atomic, radical, and stable species, as well as temperature and area expansion ratio profiles, have been determined for a nearly stoichiometric CH4-02-Ar flame and one to which 0.3 percent CF5Br inhibitor had been added. Net reaction rate profiles were calculated for all the observed species. For the normal flame, these and the mole fraction profiles gave rate coefficient information about the elementary reactions in the methane flame, for example, CH. + 0 4- H2CO 0 H, k4 = 1.05 X 1014CM3 mole-1sec-1 for 1,550§T 0,725' K; CO + OH 4 C02 + H, k6= 4.7 X 1011 for 1,350{T X1,750° K. Comparison between the inhibited and normal flame showed that A] and [CH3] were significantly reduced at the lower temperatures in the inhibited flame even though in the hot gas region the [E] [OH!, and [0] were essentially the same in both flames. The CF3Br disappears very early in the flame, relative to the fuel, and the reaction primarily responsible for its disappearance is H v CF3Br 4 HBr + CF3, where k7 is found to be 2.2 X 1014 exp(-9460/RT) for 700-1,550° K. Reaction of the inhibitor with methyl radicals provides for the relatively small amounts of CH3Br observed, but CH3 + Br2 - CHs Br + Br must also occur. The HBr formed reacts rapidly with H atoms to form H2 and Br, but the reaction is soon "balanced" in the flame as may be demonstrated by calculation of the equilibrium constant at various temperatures. The fluoro-carbon fragment produced in reaction (7) also reacts rapidly, in part with methyl radicals to give the observed elimination product CH2CF2 Later in the flame, above -1,400' K, F2CO is formed from the reaction CH2CF2 + 0 P F2CO + CH2 and k., -1.5 X 1013 at 1,600° K. The rather slow decay of carbonyl fluoride is attributed to reaction with H atoms according to the sequence F2CO I H - HF + FCO and FCO + H HF + CO.]

Jan 1, 1975

By Joseph L. Condon

Fifteen shots of three explosives with charge weights of 0.52, 1.1, 3.1, and 5.1 kilograms were fired in a pond to study the seismic effects of detonating explosives in water. Shock pressures and bubble periods were measured with pressure transducers in the water. Vibrations were measured on land in three orthogonal directions with particle velocity gages. Statistical tests indicated that a charge weight exponent of 0.43 best scaled the data. While shock pressures and bubble periods showed considerable differences in explosive performances, the amplitudes of ground vibrations showed less difference, and one prediction equation was therefore derived to estimate vibration amplitudes from all the explosives.

Jan 1, 1970

By K. E. Stanfield

[Asphalt ~~d road oil ar8 the principal products manufactured from Wyor.1in~ Ilblack oilo" \r,hich, beca.use of th?lir hig.~ E\.sphal t and hig} sulfur COi.1Jce~1t, .!?re difficult e':ld costly to refine into hi?;h-gra.de motor f 101s, burning oils. and lucri ants by presont mothods. Accordin~ly. the demand for truHle asphaltic renidl urn for the construction of roade aJ1.d other uses is 3. controlling factor in the quantity of crud~ oil prod ICed. The increasiilg -u.tilization of special aST>ha.lts as ine}""Pensive bonding, in-]

Jan 1, 1941

By R. L. Montgomery

The heats of formation of lanthanum sulfate and the enneahydrate are -939.8 ± 3.1 and -1,587.1 ± 3.2 kcal. per mole, respectively. The heat of hydration is -32.5 ± 3.5 kca1. per mole. These values were obtained from heat-of-solution measurements of lanthanum oxide and salts. Low rates of solution precluded more accurate determinations of the thermal data. The heat of formation of the chloride was similarly observed to be -256.18 ± 0.28 kcal per mole. Heats of solution and combustion of lanthanum metal yield mutually concordant results, and earlier discrepancies reported in the literature may be ascribed to impurities.

Jan 1, 1959

By L. B. Pankratz

The Bureau of Mines conducted heat-content measurements above 298.15° K for dehydrated analcite (NaAISi2O6) to 1,000°K, kaliophilite (KA1Si04) to 1,800° K, and leucite (KAlSi206) to 1,800° K. Heat content and entropy increments were tabulated, and the heat content data, were given in equation form. A first order transition was noted for kaliophilite near 810° K with a heat absorption of 160 cal/mole. Leucite had a second order transition which became complete near 955° K. In this transition a crystal change occurred from tetragonal (low-temperature form) to cubic (high-temperature form).

Jan 1, 1968

By N. S. Dalal, X. Shi, V. Vallyathan

"Correlated spectroscopic and cytotoxicity measurements were made on newly crushed silica to find whether the fracture-induced, silicon related (Si-0· or Si· type) free radicals play a direct role in the mechanism of hemolysis by silica particles. The free radical content of the silica particles was controlled through the radical decay, thermal annealing, and boiling processes, and was followed with electron spin resonance spectroscopy. Portions of the same sample were evaluated for their hemolytic potential, employing sheep erthyrocyte and optical absorption techniques. The results indicate little, if any, correlation between the amount of the silicon-based radicals and the hemolytic potential of the fresh dusts, but these or related radical sites might be contributors to silica cytoxicity and fibrogenicity via peroxidative pathways .INTRODUCTIONIn an earlier convnunication (1.) from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates free rad;cals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubin; et al.(2) have also reported the detection by electron spin resonance (ESR) of the formation of SiO· and Si·-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum (10-10 torr) (3) and subsequent exposure to air (3), and to other gases (4), these radicals were identified (2) as being formed by the hemolytic cleavage of the Si-0-Si bonds and the reactions of the Si· and SiO· ,radical with atmosphere. Fubin; et al. (2) also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anea (5) had reported that lipid peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radical studies on a given Quartz dust sample have been reported, except for some earlier work from our laboratory (1,6,7). We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radical measurements on a freshly made quartz dust. The dust’s free radical content was measured using ESR spectroscopy while its cytotoxicity poteni1al was estimated via hemolysis. Hemolysis was employed as the tox1c1ty test because it 1s a widely used method for estimating the potential of a dust for disrupting the cell membrane (8). The f1brotic potential was followed.by measuring the dust-induced lipid perox1dat1on. us1ng linole1c ac1d as a model lipid. As discussed below, the results obtained suggest new clues.to the mechanism of the Quartz-related cytotoxicity and fibrogenicity."

Jan 1, 1988

Multiple-seam interactions are a major ground control hazard in many U.S. underground coal mines. In some U.S. coalfields, particularly in central Appalachia and the West, the majority of today’s mines are operating above and/or beneath previously mined seams. The effects of multiple-seam interactions can include roof falls, rib spalling, and floor heave. These can seriously disrupt mining operations and threaten the safety of miners. In early 2006, a West Virginia coal miner was killed by rib roll that occurred in a high-stress zone beneath a remnant structure in an overlying mine. Fortunately, not every multiple-seam situation results in hazardous conditions. Indeed, the vast majority do not. For the past several years, the National Institute for Occupational Safety and Health has been conducting research to develop better techniques for predicting the location and severity of multiple-seam interactions. During this investigation, more than 50 mines were visited across the U.S. coalfields. Nearly 300 case histories were collected and analyzed using multivariate statistical techniques. The study also employed the numerical model LaM2D to estimate the multiple-seam stress, the Analysis of Longwall Pillar Stability (ALPS) and the Analysis of Retreat Mining Pillar Stability (ARMPS) programs to determine pillar stability factors (SFs), and the Coal Mine Roof Rating to measure roof quality. The study focused on the two most common types of multiple-seam interactions: • Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the main concern; and • Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The study confirmed that overmining is much more difficult than undermining, and isolated remnant pillars cause more problems than gob-solid boundaries. For the first time, however, it was possible to quantify these effects in terms of the equivalent thickness of interburden needed to compensate for them. The study also found that pillar design is a critical component of multiple-seam mine planning. Many of the failed cases involved pillars whose SF seemed inadequate once the multiple-seam stresses were accounted for. Weaker roof was also found to significantly increase the risk of multiple-seam interactions. The most important result of the study is an equation that predicts the critical thickness of the interburden required to minimize the likelihood of a multiple-seam interaction. This equation was incorporated into a step-by-step methodology that allows mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. Such measures could include installing cable bolts or other supplemental support, increasing the pillar size, or changing the mine layout to avoid the remnant structure entirely. These Proceedings also contain several previously published papers that cover other facets of multiple-seam mining research. Two papers describe the LaModel family of software developed by Professor Keith A. Heasley of West Virginia University. The LaModel programs were designed for calculating the stresses and displacements in coal mines or other thin, tabular seams in layered media. The original three-dimensional version of LaModel is essential for detailed analyses of complex multiple-seam scenarios. LaM2D, by contrast, implements a simplified two-dimensional model that is suitable for quick approximations of the multiple-seam stresses and strains. Three additional papers in these Proceedings describe the extensive multiple-seam experience of the Harris Mine, examples of extreme multiple-seam mining from the central Appalachian coalfields, and longwall mine experiences in Pennsylvania, West Virginia, and Utah. The final paper reports on a numerical modeling study that provided some insight into the mechanics of multiple-seam mining.

Jan 5, 2007

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 313, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and. January and March, 1932, as published in Reports of Investigations 3l40, 3147, 3l50, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active permissible list: [Austin Red Diamond No. 1, L. F. Gel-Coalite W. L. F. Austin Red-Diamond No. 5, L., F. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No. 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.]

Jan 1, 1932

By Eric B. Sansone

The Federal Coal Mine Health and Safety Act of 1969 requires coal mine operators to sample accurately the amount of respirable dust in the mine atmosphere. A technique approved for such sampling employs a 10 mm nylon cyclone followed by a membrane filter (nominal pore size ????= 5 µm) and a pump. The pump is required to provide a flow rate of 2.0 ± 0.1 liters per minute. Calibrations have yielded a range of flow rates (1.4 to 2.8 1pm) at which the cyclone should be operated to remove the non-respirable portion of the dust. The purpose of this project was to evaluate the performance of the 10 mm nylon cyclone at flow rates of 1.8 and 2.0 1pm using a polydisperse coal dust aerosol. The penetration characteristics of the cyclone were to be compared to the United States Atomic Energy Commission's respirable dust standard. The effect of relative humidity on cyclone penetration characteristics was also to be observed.

Jan 1, 1973

By J. P. McGee

As part of a joint U.S. Atomic Energy Commission-Federal Bureau of Mines program for using nuclear energy to supply process heat, a simulated nuclear loop has been constructed to test components. This loop has been operated for more than 1,800 hours at 100 p.s.i.g. Of this period, 23 hours were at 2,500° F. and higher; 540 at 2,000° to 2,500° F.; 840 at 1,500° to 2,000° F.; 200 at 1,000° to 1,500° F.; and 260 below 1,000° F. Leakage at flanges and welds was not a serious problem. A helium-recycle system with gas temperatures of 2,300° to 2,500° F. and a static pressure of 250 p.s.i.g. appears feasible. Difficulties were encountered with the recycle compressor due to thermal distortion of the impeller and shaft. The use of sealed bearings limits compressor operation to the life of the bearings.

Jan 1, 1960

By L. B. Pankratz

Enthalpies above 298° K were determined for AgCl to 1,400° K and for AgBr to 1,200° K by copper-block calorimetry. Before melting, both compounds showed an anomalous increase in enthalpy, an effect associated with lattice defect formation. Melting points and heats of fusion were determined to be AgCl, 730° K and 2,945 cal/mole; AgBr, 700° K and 2,030 cal/mole. The heat capacity of both melted substances decreased with increasing temperature over the entire liquid ranges investigated. Enthalpies above 298° K were tabulated at even temperatures along with derived entropy increments and heat capacity values. The results were combined with the known heats of formation and entropies at 29.8.15° K to obtain values of the heats and free energies of formation over the range 298.15° to 1,400° K for AgC1 and 298.15° to 1,200° K for AgBr.

Jan 1, 1970

By D. W. Blaylock

1. The Lower Freeport and Lower Kittanning beds are the most important beds in Clearfield County, Pa., from the standpoint of production. The Lower Kittanning bed has the largest remaining recoverable reserves of any of the beds in the county. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 1,909 million short tons as of January 1, 1953. Of this total, 1,177 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By J. M. Stuve

This Bureau of Mines investigation measured the low-temperature heat capacities of FeOC1(c) and FeC13(c) in the temperature ranges of 6 to 305 K and 4.6 to 300 K, respectively. The standard entropies (S°, 298.15 K) of FeOCl(c) and FeC13(c) were derived as 19.73±0.03 cal/deg-mole and 35.33±0.07 cal/deg-mole. A large lambda transition was observed in the heat capacity of FeC13(c) at 8.4 K. The standard enthalpy of formation (?H°f, 298.15 K) of FeOC1(c) was determined to be -98.23±0.22 kcal/mole by HC1 solution calorimetry. High-temperature enthalpy measurements (H-H298.15) of FeOC1(c) were determined to 700 K by precision drop calorimetry. Standard thermodynamic formation data and related functions were tabulated at various temperatures for FeOC1(c) and FeC13(c).

Jan 1, 1980

By D. J. Donaven, Manuel Gomez, W. S. Landers

Bulk density tests were made on a Western U.S. coke oven plant blend to obtain bulk density control data that would be directly transferable to plant practice . Maximum bulk density values were obtained at zero surface moisture . Increase in surface moisture to about 6 percent decreased the bulk density to a minimum value . Increase in the fine grinding of the blend , at constant surface moisture , decreased the bulk density . The effect of oil on bulk density was observed with five oils at concentrations ranging from 1/8 to 1-1 / 2 gallons per ton . Maximum bulk densities were obtained within the 1 / 2- to 1 - gallon - per - ton range . Essentially the same bulk densities were obtained with petrolatum- and nonpetrolatum- containing oils . Storage effects were observed on samples tested at selected intervals from 0 to 56 days . No significant change in bulk density took place if no surface moisture was lost during storage .

Jan 1, 1964

By Donald P. Blasko

The Bureau of Mines investigated two areas of oil and gas seeps in the north-central Gulf of Alaska--Katalla River to Bering River and Cape Yakataga to Yakutat Bay to determine (1) whether previously reported seeps are still active, (2) the characteristics of the seeping hydrocarbons, and (3) the amount of bitumen contained in the drainage leaving the seeps and entering the Gulf of Alaska. Thirteen separate oil seeps, six bitumen deposits, and eight gas seeps were located, sampled, and analyzed. The oils ranged from 35.2° to 14.1° API gravity and had sulfur contents from 0.53 to 1.31 wt-pct. Bitumen samples had API gravities from 2.4° to 14.6° and sulfur contents from 0.28 to 0.88 wt-pct. Gas samples had specific gravities ranging from 0.577 to 0.883 and caloric values from 724 to 1,427 Btu/cu ft. A total of 63 water samples obtained from seep locations and seep drainages were analyzed by atomic absorption spectrophotometry for ionic content and by solvent extraction for hydrocarbon content. Although some of the water at the oil seeps had a bitumen content as high as 246,000 mg/1, the amount of hydrocarbons actually reaching the Gulf of Alaska averaged <0.2 mg/1.

Jan 1, 1976

By B. S. Covino

The Bureau of Mines has conducted a laboratory and field corrosion test¬ing program to determine materials of construction for the leaching and gas-sparging crystallization environments of the clay-HC1 process in order to more fully utilize the alumina from domestically available kaolinitic clays. Laboratory tests were used to determine the corrosion rates of 22 metals and alloys by weight-loss measurements in these two environments of the process. The results of this laboratory study were used both to suggest metals and alloys for field testing and to determine the effect of the individual solution components on the corrosion behavior of the metals and alloys. Results from the field tests were used to recommend Ta, Ta-2.5W, and Ta-10W for con¬struction of the agitators for the leaching process. The metals and alloys recommended for construction of the gas-sparging crystallizer heat exchangers were Ta, Ta-2.5W, Ta-10W, Nb, Nb-1Zr, Nb-3Zr, Nb-28Ta-10W-1Zr, Nb-10Hf-1Ti, and Zr for the first stage and Ta, Ta-2.5W, Ta-10W, Nb-28Ta-10W-1Zr, Nb, Nb-10Hf-1Ti, and Zr for the second stage.

Jan 1, 1981

By G. R. Hopkins

Crude-petroleum pipe lines in the United States on May 1, 1941, had a total length of 118,350 miles - an increase of 7,770 miles since Jun, 30, 1936, then the last previous survey was made by the Bureau of Mines. The expansion was due almost entirely to trunk-line construction, as the mileage of gathering lines was virtually unchanged from 1936. The greatest mileage of gathering lines, 53,640, was recorded in the survey of May 1, 1931. Both trunk and gathering-line mileage decreased moderately, in the interval from 1531 to 1936, but the present survey indicates that trunk-line facilities have expanded since 1936 to new high levels. Truck-line mileage equaled 55 percent of the total mileage of all crude lines on May 1, 1941, and 52 percent is 1936. The total length of gasoline pipe lines on May 1, 1941, was 9,001 miles this does not include several hundred miles of life under construction at that time or several hundred additional miles now being laid. No detailed surveys of gasoline mileage were made for 1, 1931, and June 30, 1936, but the mileage for those dates was about 1,400 and 4,600, respectively.

Jan 1, 1941

By Gene Asai

Properties obtained for columbium carbide-carbon castings ranging in car-bon content from 12 to 17 weight-percent were compared with those of hot-pressed composites of similar composition. The properties were oxidation resistance in static air between 500° and 700° C, linear thermal expansion between 20° and 2,400° C, electrical resistivity between 20° and 1,500° C; microhardness between 20° and 1,500° C, and modulus of rupture between 1,300° and 1,800° C. CbC-C castings differed markedly from hot-pressed material with respect to microstructure, electrical resistivity, and modulus of rupture, but behaved quite similarly with respect to oxidation resistance, thermal expansion, and hot hardness. In oxidation resistance, thermal expansion, and hot hardness both materials were independent of carbon content. Both castings and hot-pressed composites oxidize rapidly in air above 600° C, have thermal expansion coefficients very similar to columbium metal, and the logarithm of the hardness decreases linearly with increasing temperature. The microstructures of hot-pressed composites contained varying amounts of graphite in a CbC matrix but did not contain significant amounts of a eutectic structure present in all castings, nor did they contain graphite needles which were present in the hypereutectic castings. The higher electrical resistivity of hypereutectic castings over hypereutectic hot pressings was attributed to the presence of highly oriented graphite needles in the castings. The modulus of rupture of castings was 1-1/2 to 2 times that of hot-pressed composites. Both materials displayed bend ductility above 1,800° C.

Jan 1, 1971