Search Documents

By W. E. Lamont

The Bureau of Mines conducted flotation tests on a mixture of barite waste materials from Nevada in which essentially all of the barite values were finer than 20 micrometers. Flotation variables investigated in these tests were the effects of (1) sodium silicate as a pulp dispersant, (2) sodium hydroxide as a pH modifier, (3) increased amounts of sodium cetyl sulfate, (4) conditioning time and (5) solids content during conditioning. The optimum flotation conditions were achieved by adding 2.5 pounds of sodium silicate and 10 pounds of sodium cetyl sulfate per ton of feed and conditioning the pulp for 20 minutes at a 35-percent solids content. Using these conditions, a concentrate was produced that contained 94.7 percent BaS04, with an attendant recovery of 90.9 percent of the barite in the feed. In addition to the flotation tests, a selective barite flocculation process was developed to treat extremely fine barite. A barite concentrate containing 96.5 percent BaS04 with an attendant recovery of 82.1 percent of the barite was produced by selective flocculation. A process patent application has been filed based on this process.

Jan 1, 1982

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

7. Development of Acoustic Seal Checking System The acoustic approach was shown in Section 4 of this report to be the most promising concept for checking the seals. This section describes the development of this concept into a working hardware system to be used later in the field test program. This development effort included: (1) Theoretical analysis of the acoustic behavior in the mine using acoustic modeling- techniques. (2) Experimental determination of acoustic patterns in mine passages. (3) Refinement of the theoretical model. (4) Verification of final theoretical predictions in the quarter-scale laboratory model of a mine passage and seal. (5) Development of system specifications. (6) Development of the Acoustic Prototype Seal Checking System. 7. 1 Analysis of the Acoustic Seal Checker Concept The acoustic seal checker concept is based on a model which combines corridor acoustics and hole transmission theory. The idealized model for the mine sealing application is shown schematically in Figure 66. A high intensity acoustic- source is located in a corridor at a, position adjacent to the location to be sealed. The acoustic signal transmitted through the seal is monitored by a microphone pick-up placed on the opposite side.

Jan 1, 1973

Lead Tariff.--The full House Ways and Means Committee approved H.R. 6089 which will have the effect of reducing the tariff on unwrought lead to 3% ad valorem, with a floor duty of 1.0625 cents per pound, compared with the currently effective rate of 3.5% ad valorem. Consideration is also being given to tariff rates on imports of red lead and litharge from Mexico. A consortium of domestic producers has appealed to the Office of the Special Trade Representative (STR) requesting a return to tariff schedules which were in effect prior to the concessions made effective on January 1. Mexican producers have filed a proposal in favor of lower duties, and the matter now awaits a ruling by the STR. Ferrous Scrap Exports.--After holding public hearings and receiving public comments in May, the Department of Commerce announced that it would not institute formal monitoring of ferrous scrap exports, as requested by the Ferrous Scrap Consumers Coalition. The Department said, however, that it would follow the trend of scrap exports and prices. Ferrous scrap prices are currently low and supplies are reported to be adequate.

Jan 1, 1980

New GSP Trade Status Approved.--President Carter, by Executive Order effective March 30, has approved Generalized System of Preference treatment for imports of nonferrous metal products and other imports from Ecuador, Indonesia, Zimbabwe, Uganda, and Venezuela. As of May 2, Afghanistan and Ethiopia will be taken off GSP status. Under the Generalized System of Preferences, certain imports from developing countries are provided duty-free treatment. A country can lose its GSP status if its shipments of the product exceed $41.9 million or more than 50% of total U.S. imports during the preceding year. However, the President can waive the 50% rule in cases where total U.S. imports of an item in 1979 were less than $1 million. Certain nonferrous imports from Mexico, Peru, Chile, and Zambia are already covered by GSP. Hearings April 10 on International Tin Agreement.--The Fifth International Tin Agreement of which the United States is a signatory, which entered into force on July 1, 1976, will expire on June 30, 1981. A negotiating conference for a Sixth International Tin Agreement will be held under auspices of the United Nations at Geneva from April 14 to May 16, 1980.

Jan 1, 1980

By Donald O. Capstick

A mineral survey of the 520-acre Quigg West Wilderness Study Area (MT-074-155) was conducted by the U.S. Bureau of Mines in 1986 at the request of the U.S. Bureau of Land Management in order to evaluate its identified mineral resources. The Wilderness Study Area is in Granite County in western Montana about 16 miles northwest of Phillipsburg and 27 mi les northeast of Hamilton, MT. Stony Mountain, a study area on lands administered by the U.S. Forest Service, is about 1 mile to the south-southwest and was studied concurrently. No mineral resources were identified in the Quigg West Wilderness Study Area, but high grade gold assays, as much as 1.24 ounce gold per ton, were obtained at the one prospect found. Samples from four workings contained significant gold; minor silver, molybdenum, and copper were also present. The prospect containing the narrow and discontinuous gold-bearing quartz vein straddles the south boundary of the Wilderness Study Area. The shear zone containing the vein projects toward the old Crescent mine, about 4.5 miles to the south, which shows a similar geologic structure.

Jan 1, 1987

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines developed induction slag melting process is of concern to members of the titanium industry. The objective of the research was to determine the effect of CaF2 inclusions on the properties of titanium and its survival rate during melting. The data were obtained from single induction-slag-melted ingots prepared with the normal addition of 4 pct and also with 2- and 1-pct additions of CaF2 slag. The results of this effort showed that the mechanical properties of single-induction-slag-melted Ti-6Al-4V alloy exceed the minimum values specified in Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H, but these materials are much more notch sensitive in fatigue than normal Ti-6A1-4V alloy titanium. First and second vacuum-arc remelts of single-induction-slag-melted ingots fragmented and increased the number of inclusions, while reductions in the amount of flux resulted in an upward trend in the spatial distance between pores in an x-y plane.

Jan 1, 1988

By N. B. Greninger

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4-and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 2010

By H. O. Poppleton

This Bureau of Mines study was made to investigate a possible method for selectively removing the Si02 component of silicate minerals and ores. Of specific interest were aluminum ores and zircon. Methods are described for removing Si02 from these ores as volatile silicon sulfides by treating the ore with sulfur and carbon; with sulfur, carbon, and a reducing gas; or with sulfur compounds and carbon. Comparative results are also given for the desilication of some of the ores with carbon alone to form volatile silicon monoxide. The silica component can be removed partially from bauxites at temperatures above the sublimation temperature of SiS (940° C) by treatment with carbon, sulfur, and methane; however, it is more difficult to remove the silicon from kyanite, manganese silicate, red muds from aluminum processing, kaolinite, lateritic nickel ores, and zircon. Complete desilication requires temperatures ranging from 1,100° C for bauxite to 1,450° C for zircon. Although the high temperatures required and the undesirable metal sulfides produced eliminate practical application of this method using present technology, the Bureau is reporting this data so that they will be available to future investigators.

Jan 1, 1974

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

Assure fail-safe stopping of a mining vehicle immediately following a loss of electric power. Approach A separate emergency brake system which actuates when electrical power is interrupted, was installed on several mining vehicles and tested in a long-term underground mining demonstration. How It Works Separate, spring-actuated brakes, which press against brake discs, are used to stop the vehicle following power failure. To allow norm al movement of the vehicle, hydraulic oil under pres? sure from the vehicle's hydraulic system is directed to a spring? loaded piston in each emergency brake housing. That pressure causes the piston to compress the spring and relieves the spring pressure against the puck, thereby allowing the brake disc to turn freely. See Figure 1 A. If the electrical power fails or if the machine is turned off, a valve in the hydraulic line to the emergency brakes opens. That valve, shown as ?Solenoid Valve (automatic)" in Figure 1, which is normally held closed by its electrical solenoid while the vehicle is electrically powered, is opened by the spring in the valve assembly. The pressure in the hydraulic line which is connected to the emergency brakes then drops to

Jan 1, 1978

Determine what diameter piping is necessary to obtain sufficient water flow to spray nozzles used for dust suppression. Approach A simplified, diagrammatic method of calculating the flow of water through a proposed system consisting of a supply line and two banks of spray nuzzles is outlined. How It Works The pressure versus flowrate of the supply at the tapping point must be known or measured. The supply curve of typical city water at a 1 ¼ -inch pipe outlet is shown by the lowest curve in Figure 1. A supply curve for a typical pump fed from an open sump is shown by the middle curve. The combination of these, the supply curve of a pump fed by the city water supply is shown by adding the lower two curves to get the upper curve. A pump supply curve showing flowrate versus pressure is usually supplied by the manufacturer. The water supply line flow curve can be determined by measuring the time required to fill a 55 gallon barrel at various valve settings to determine flow, and by measuring corresponding pressures at the valve with a gauge.

Jan 1, 1979

Reduce the number of conveyor-related accidents in the mining industry by providing recommendations for effective operation of conveyor belt cleaning systems. The Problem Troughed belt conveyors provide effective, and efficient materials transport and their use has increased throughout the mining industry. Carryback, the spillage that accumulates under the belt, is a problem even with belt cleaning systems installed. Mining personnel are exposed to safety and health hazard; as they attempt to clean up this spillage. Approach To investigate the influence of metal-segmented-blade belt cleaners on the amount of carryback spillage, the. Bureau identified and tested the following parameters: (1) amount of pressure applied to the cleaner blades, (2) friction between the blades and conveyor belt, and (3) wear rates of different metal blades. The test parameters were quantified by recording the amount of carryback material passing the metal cleaner blade, and the weight loss of the blades. The data collected were used to identify the following critic d operational parameters of a segmented-blade conveyor cleaner system: (1) the existence of an optimal operating pressure for the conveyor and cleaning systems and (2) elimination of recessed patterns on the working side of the conveyor belt.

Jan 1, 1989

By J. D. Corrick

Research was conducted to develop operating techniques and define some of the limiting parameters for microbially converting hydrous calcium sulfate to hydrogen sulfide. The work was carried out in either glass stoppered flasks or anaerobic fermentors. Using the criteria of pH, temperature, number of bacteria per milliliter of test solution, and hydrogen sulfide produced, it was shown that hydrous calcium sulfate could be microbially converted to hydrogen sulfide at a rate of 7.3 g H2S/1 of fermentor volume per 24 hours. The various parameters defined were pH, temperature, and medium exchange rate. These were shown to be a pH range of 7.2 to 8.8, a temperature range of 30° to 35° C, and a medium exchange rate of 70 percent of the ferment or volume per 24 hours. It was also shown that a daily waste was between 50 and 77 percent as effective as sodium lactate in supporting the production of hydrogen sulfide and that by utilizing a gas to purge the fermentation system, a 1.7-fold increase in hydrogen sulfide was obtained.

Jan 1, 1970

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"This report is () expansive test program by the Bureau of Mines to determine methods from various and ferrous manganese-grade product () widespread () and manfniferrous iron ores. Among the samples received for testing was one from the pits of the Barytes Mining Co., 1-1/ 2 miles northeast of Cartersville, Ga.. The property is approximately in the center of the Cartersville manganese district and shares a common corner with properties of the New Riverside Ochre Co. and the Etowah Development Co., both producers of manganifereus ores. The deposit is typical of the district and occurs in residual clays resulting from weathering of the Shady limestone and Weisner quartzite. 7/The property is developed by a number of open pits ranging to 60 feet in depth. In 1918 several carloads of manganiferous iron ore was mined from an alit on the property. Since then mining operations have been negligible. The ore is known locally as calico ore.A 4-ton sample representing -re as it occurs in the -pen pits vas furnished for testing. The sample consisted of a mixture of red iron oxides, wad, and clay, with small pebbles of manganese oxides and siliceous fragments scattered throughout."

Mar 1, 1943

By R. E. Peterson

The Bureau of Mines has undertaken beneficiation investigations on samples representing large tonnages of oxidized taconites in order to develop and evaluate applicable technologies for producing iron oxide concentrates from these materials. Information derived from the investigations can be used to expand the domestic iron raw-materials base and to establish the impact these taconite deposits may have on future national iron ore requirements. This report describes a process that includes reduction roasting, magnetic separation, and flotation, applied to a western Mesabi Range sample taken near Coleraine, Minn. The sample contained 36.8 pct iron and 46.0 pct silica, and represented 0.5 to 1 billion tons of crude material. An average of 962 lb/hr of oxidized taconite was roasted with 33 lb/hr of lignite in a 35-foot-long rotary kiln. Pulverized lignite and natural gas maintained the kiln operating temperature at 850° C. The roasted taconite was beneficiated by magnetic separation and cationic flotation in a 900-lb/hr pilot plant and yielded a product analyzing 68.1 pct iron and 4.6 pct silica, and containing 82.4 pct of the iron in the kiln feed.

Jan 1, 1981

By B. J. Scheiner

Oxidation procedures based on the chlorine-hypochlorite system were investigated for improving gold recovery from carbonaceous gold ores. The oxidation pretreatment prior to cyanidation was accomplished by (1) addition of sodium hypochlorite to ore pulp, (2) by addition of chlorine to ore pulp, and (3) by generation of hypochlorite in situ by electrolysis of a brine solution used to pulp the ore. Gold extraction of 90 pct was achieved by cyanidation of carbonaceous ore that had been pretreated with 20 Ib per ton sodium hypochlorite at 50° C for 4 hours. Similarly, pretreatment of the ore pulp with 35 1b chlorine per ton at 24° to 30° C and 15 hours reaction time resulted in 89-pct gold extraction by subsequent cyanidation. Concomitant studies showed that electrolyzing the pulp prepared with a brine solution was equally as effective as electrolyzing hypochlorite and chlorine for oxidizing carbonaceous ore constituents that are deleterious to cyanidation. Gold extraction of 90 pct was obtained by electrolysis when 275 lb of are was treated at 200 amp for 7 hours in an 8-to 10-pct salt solution. Power consumption was in the range of 60 kwhr per ton.

Jan 1, 1972

By Arden D. Fugate

The Federal Bureau of Mines conducted extensive studies on solid-state defluorination (laboratory scale) and tests on molten defluorination (intermediate scale) of siliceous fluorspars. The studies were made to develop a pyrohydrolytic process for liberating fluorine from offgrade fluorspars. Test results showed that more than 90 percent of the fluorine can be evolved by solid-state defluorination at 1,300° C., and more than 97 percent can be liberated by molten-state defluorination at 1,420° C. Solid-state defluorination conditions were established by conducting tests on mixtures of ceramic-grade fluorspars and high-purity silica flour. Pelletized mixtures were defluorinated under varying conditions of time, temperature, and relative concentrations of silica, calcium fluoride, and water. The effects of adding various amounts and combinations of aluminum oxide and iron oxide on defluorination were also studied. Investigations of solid-state defluorination indicates that the following two reactions are involved: 2CaF2 + 3SiO2 = 2CaSiO3 + SiF4, and CaF2 + Sio2 + H20 = CaSiO3 + 2HF, The second reaction is dominant, although significant defluorination can be achieved by the first reaction.

Jan 1, 1961

By K. K. Kelley, L. B. Pankratz

The heat contents of four silicate minerals -- akermanite , cordierite , gehlenite , and merwinite --were measured from 298 ° to around 1,700 ° K by the dropping method . The results were compiled into tabular and equation forms suitable for thermodynamic calculations . The heat contents of these compounds are nearly additive with respect to their constituent oxides .

Jan 1, 1964

By Thomas M. Barczak

Purchasing a new set of longwall shields requires a substantial investment. A poor shield design can lead to economic hardships, safety concerns for the mine workers, and closure of the mine. This paper addresses several key points that should be considered in the procurement process: (1) understanding your goals and the logic in selecting a higher capacity shield, (2) the importance of completing performance testing before production shield fabrication begins, (3) making sure performance testing is properly done, (4) measuring load(stress) development during performance testing, (5) testing a shield to failure, and (6) the value of buying extra shields. In addition, several challenges are proposed for consideration in future shield designs. These include (1) 100,000 life-cycle expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control by optimizing setting pressures, (4) lubricated link joint design concepts, (5) composite material applications to reduce shield weight, (6) incorporating periodic weighting predictive algorithms into the data-processing software, (7) advanced component load measurement on two to three specially instrumented shields to detect loading in the structural components, and (8) constant set leg cylinder design.

Jan 10, 2000

By Foster Fraas

Review of the literature on solid solutions discloses that the relation between composition and magnetic susceptibility is not linear . Recalculation using a transformation of composition values to parameter v values provides for a linear relation with the magnetic susceptibility to the 1/2 power . Application to minerals is illustrated by the olivine and enstentite series .

Jan 1, 1964