Search Documents

By Daniel Johansson, Markus Danielsson, Håkan Schunnesson

In sublevel caving, blasted material flows gravitationally into the drawpoint from above in a periodical manner. This type of flow behavior entails muck pile conditions that are variable along the course of extraction. The effect of this variability on the LHD (Load-Haul-Dump) operation in terms of loading efficiency and ability to undermine the blasted ring is not fully understood as of today. This paper presents results from a field test in LKABs Malmberget mine in Sweden, where the influence of fragmentation on the loading operation has been studied in detail. Drawpoint filming was conducted for extraction of two rings equivalent of roughly 10000 metric tons (~9842 long tons) of material each. The analysis includes fragmentation measurements, muck pile classification, and general estimations in terms of loadability. Further, an evaluation of LHD machines from two different manufacturers was conducted to identify and highlight differences. The results show that fragmentation, muck pile compactness, and flow characteristics are all interdependent. Flow disturbances and the subsequent loading of compacted fine material in the back of the ring have been identified as the main reason for occurring problems and prolonged digging times. However, the ability to sufficiently undermine the blasted ring has been identified to primarily depend on digging depth which is only observed to be high during flow disturbances. An absence of flow disturbances seem to promote high loading efficiency but simultaneously limit the maximum digging depth. A mid-range particle size distribution with a low amount of fines has proven beneficial for overall loading efficiency. The various LHDs employed showed significant variations in terms of ability to handle difficult loading situations (e.g. compactness, boulders, etc.).

Jan 1, 2018

By John Tatom, Michelle Crull, Robert Conway

The US Department of Defense Explosives Safety Board is sponsoring the development of a risk-based explosives safety siting program, SAFER. The fragment and debris hazard generated at the potential explosion site (PES) is critical at an exposed site (ES) over a significant range of standoff distances. The Science Panel Impact Debris Evaluation and Review (SPIDER) test program has been planned to develop improved predictions for the hazards inside an ES by fragments and debris. Data will include the mass and velocity required for perforation of the test cross-section and the characteristics of all debris produced inside the ES.

Jan 1, 2010

By Tapan Goswami, Lloyd Hain, Geoff Brent

For many years Ramp 24 at Ensham mine in Queensland, Australia has suffered substantial coal loss and damage due to the fragile nature of the coal and problematic geological conditions, which have proved very challenging. In the past various blasting techniques were applied in attempts to improve coal recovery. One approach was to use a shallow throw (cast) blast followed by a separate post-strip blast underneath. Another method was the introduction of the practice known as “baby decking” with the addition of a large buffer of material in front of the coal. However, despite increasing mining costs, none of these techniques adequately reduced coal edge loss and damage.

Jan 1, 2008

By Luiz Guilherme Isfer Maciel, Marilena Cardu, Fernando Golin, Jacopo Seccatore

"This study applies the concept of the difficulty of tunnelling by drilling an blasting (D&B) to selectedcases from the Brazilian tunnelling industry. The difficulty of tunnelling has been defined in previouswork as the difference of specific drilling (SD) from industrial average trend: easier when SD is lowerthan average, more difficult when SD is higher than average. Results show how tunnels in Brazil tend tobe unrealistically more difficult to excavate when compared to similar excavations in similar geologies elsewhere in the world. It is thoroughly discussed the reason for such anomaly (up to +90% SD compared to industrial average). One reason could be the lack of options amongst explosive products on the brazilian market. Only ANFO and explosive emulsions are available in Brazil. Lacking high VOD(Velocity of Detonation) products might result in reducing the maximum allowable burden amongstproduction holes, therefore increasing SD. Another reason could be found in the tunnel designers’tendency of choosing D&B as excavation method for weak rock masses that would benefit from mechanical excavation. The reason to this tendency can be partly found in the lack of availability of mechanical excavation machines in the brazilian market. Blasting in weak rock masses requires more careful smooth blasting, hence a closer spacing amongst contour holes to avoid costly overbreak: this increases SD. A third reason could be found in the lack of skill amongst the local workforce. When dealing with unskilled workers the blast designers naturally tend to avoid highly optimized blasts thatrequire very skilled workforce to be realized on field. The designer in this case tends to leave the blastdesign simpler but more robust, at the cost of higher specific drilling and specific charge. The conclusions suggest that this unrealistic difficulty when compared to world average could be a simptom of the so-called “Brazilian cost” within the tunnelling industry."

Jan 1, 2017

By John Norman

This paper will cover blasting techniques that are applicable to underground and other rescue that involves removing obstacles and breaking rock in close proximity to rescuers and subjects.

Feb 1, 2020

By Mark Bosse

This is a paper demonstrating the use of a fixed wire and trolley system to deliver 2 or 5 lb cast primers (with 2 meter cap/fuse assemblies) deep into avalanche terrain. This avalanche terrain is mitigated using explosives prior to being opened to guests.

Feb 1, 2020

By Clara Godoy, Paulo Couceiro, Juan Navarro

The continuous automatization and digitalization of the different stages involved in any underground construction bring new possibilities to optimize the operation. One of the most important requirements for the development of these projects consist of a proper rock mass characterization for optimizing the stages of the drilling, blasting and support cycle. In the last few years the road to digitalization has gone through data science and big data, showing the importance of data gathered to describe the geological and geotechnical environment that surrounds the operations. Since rock characteristics have an important influence in the drilling response, the technological advances in the sensorization of drilling machinery such as the Measurement While Drilling system (MWD) allow to gather the necessary amount of information to be applied in data science processes to evaluate changes in the rock mass with higher resolution than conventional methods. In this paper, Machine Learning techniques have been used to combine data monitored from the drill rigwith scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure. Considering blasting factors as constant, the model combines the rotary, percussive, hydraulic flushing and the rate of advance of the drilling, and the confinement of the rock mass by depth, to detect zones with different rock properties. This provide an early information of the rock mass condition around the blastholes and the prediction of expected overbreak generated after blasting, being possible to design more efficient bastings, in which each borehole is filled with the right and necessary explosive charge. The analysis comprises data from 57 blasts (around 1700 contour blastholes) and more than 4000 excavated sections.

By Emily Johnson, Catherine Johnson, Rachel Bauer, Paul Pitzel

Demolition projects involving explosives may incorporate cutting charges to sever columns in collaboration with kicker charges that “move” the columns out of alignment. Traditional kicker charges often involve the use of dynamite secured to the column above the cutting charge. Nitroglycerine, the main component of dynamite, causes medical problems and can be a hazard to workers on site. Dynamite can also cause fragmentation of the column and structures, resulting in potential injuries to people or leading to the possibility of cutoffs in neighboring charges. This study investigates the use of water-cased kicker charges to reduce the amount of dynamite in demolition. Water charges, traditional charges, and detonating cord charges were placed on hanging steel columns and analyzed for the fragmentation of the column and velocity of the column. A W 10 X 22 beam was hung in an underground limestone test area and allowed to swing freely acting as a severed column. Charges were attached to the bottom of the column with tape and initiated using electric detonators. Explosive charges of dynamite or detonating cord were placed in the center of a water container or directly on the column for use as the kicker charge. Tests were recorded with high-speed video and velocity was calculated using Phantom Camera Control software. Velocity and time were then used to calculate force, kinetic energy, impulse, and pressure exerted by the explosive on the column. The water charge transferred energy to the column over a larger area with no direct contact of explosive and the column. Water charges moved the column faster and with more power than traditional charges. After preliminary tests, water charges were also used as the primary kicker charges in a full-scale demolition project as a case study using 118 charges. The kicker charges successfully moved building members without creating fragmentation while using less dynamite than traditional kicker charges. Due to the success, multiple full-scale projects are being designed using water charges to show success and repeatability.

Feb 6, 2023

By Clara Godoy, J. A. Sanchidrian

In this paper, Machine Learning techniques have been used to combine data monitored from the drill rig with scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure.

Feb 1, 2020

By Sven-Erik Johansson, Gosta Rundqvist, Donald Jonson

In Stockholm a new road traffic system called Södra Länken (Southern Link) will be in operation in late 2004. The total length of the road system is 6 kilometres of which 4,5 kilometres run through tunnels under suburbs immediately south of Stockholm inner City. The new traffic tunnels together with existing Metro tunnels, which mostly are in rock, will be the determining factor for blast design for many projects in the future. To set reasonable and safe permitted vibration levels the Swedish National Road Administration, Stockholm Region and Stockholm Transport Rail System have together financed a project to determine guide levels for blast-induced vibrations in traffic tunnels in rock. The purpose of the project has been to establish guide levels that are appropriate for different types of rock tunnels.

Jan 1, 2004

By C. Heiss, A. Hofmann

Due to an explosion in an Austrian steel works during the basic oxygen process, the Chair of Mining Engineering and Mineral Economics at the Montanuniversitaet Leoben was assigned with the set-up of a test arrangement to study the effects of large-scale particle emissions on the plant´s installations and the testing of various structures and structure-combinations to be applied as explosive-proof enclosure.

Jan 1, 2012

By Winfried Rosenstock, Carlos Orlandi

Along the Pacific West coast of Latin America there are several large operations of metal mining activities. To mention only a few: Chuquicamata in Northern Chile moving daily approximately one million t of copper ore and waste, Cerro Verde near Arequipa in Peru, or lanaccocia. Apart from the coal deposits in north-east Columbia it is mainly to deal with metal-mining, which has due to geographical reasons relatively high cash-cost. This sector of mining is traditionally severely depending on the world-market.There are reasons to believe that the world-market will remain on a low price level and some analysts predict that in general the price-level will continue on low basis for the next decade. The cash-cost factor becomes therefore even more important as it already is. The goldprice development during the year 1999 illuminates that market changes can quickly lead to a severe crisis which forces the shutdown of mines with cash-costs close to or above the present market price per ounce. The breakdown of the cash-cost shows, however, that there are ways to overcome even the crisis like it struck the low-grade open pit goldmines around the world. Especially hitherto the “Electronic Option” is the only solution as the possible reduction using advanced technology based on the application of electronic detonating systems and newly developed special ignition procedures. The electronic option will lead to tremendous cost reductions similar to the results of research operations Thiess Contractors, Brisbane, Australia have carried out in Australia in 1998 and 1999. The electronic option allows a comprehensive integration of side effects of the blasting process which in the past could not have been achieved so far. Electronic initiation can achieve secondary effects which have an additional and positive impact on the level of costs. Appropriate application can enhance the production of material which will reduce the primary crusher costs or even make a primary crusher operation obsolete.

Jan 1, 2000

By Agung Wibowo

The incident of Ammonium Nitrate explosion in Beirut on August 4, 2020, became a wake-up call to Ammonium Nitrate stakeholders for mining and construction regarding the deadly risks associated with explosives management. This is a very expensive a lesson learned for all parties involved in the storage of explosives.

Feb 1, 2020

By Cesar Guerra, Alejandro Rojas, Dr. Jhon Silva, Luis Velasquez

The ANN method is applied to predict the P_80 size in one open pit gold mine in Peru. The ANN was implemented in Matlab programming language, and the results from the ANN are compared with data obtained using photo-fragmentation analysis software.

Feb 1, 2020

By Mauritz Kotze, Jason Furtney, Ewan Sellers, Sandy Etchells, Tom Szendrei

The development of a simple model for gas flow and burden movement has driven the need to improve our understanding of burden breakage mechanisms for single hole blasts and the interaction between multiple holes in solid and jointed rock masses. Conventional analytical understandings of the burden breakout using the elastic-tensile fracture model were studied and found to provide a breakout angle that is independent of burden in contradiction to experimental data. By considering rock fracture in terms of Mohr-Coulomb plasticity using analytical expressions from the field of cavity expansion analysis an improved relationship between breakout angle and burden is derived until the point of critical breakout at which the angle of breakout suddenly changes from between 90 degree and 100 degrees to zero. This suggests that the critical burden occurs at about 0.6 times the radial fracture zone calculated from the analytical solutions.

Jan 1, 2013

By Donna Kliche, Charles Kliche

It has been previously documented that various weather conditions such as wind direction and speed, cloud cover and, especially, temperature inversions can significantly affect the overpressure generated by a blast event (Siskind et al, 1980; Oriard, 1999; Siskind, 2000). The overpressure can be magnified downwind and reduced upwind; a change in the regular profile of temperature with elevation can magnify or focus the sound intensity at some distance from the blast event.

Jan 1, 2011

By Anderson da Cunha Meireles, Pedro Garcia, Ernst Young, Leandro Coelho, Carlos Eduardo Soares Feliciano, Key Fonseca de Lima

Rock blasting is a crucial technique employed in mining construction and quarrying industries to fragment large rocks into smaller, more manageable pieces. However, it often generates ground vibrations that can pose significant challenges. This study explores the application of Conformal Prediction (CP) in the context of rock blasting to develop predictive models that estimate blasting-induced vibrations and quantify the associated uncertainties. Various machine learning models were integrated within the CP framework using MAPIE and CREPES libraries. The results demonstrated the effectiveness of CP in providing statistically reliable prediction intervals, making it particularly useful for applications where the stakes of underestimating uncertainty can be high.

Jan 21, 2025

By Greg Wyartt

"At an Australian iron ore open-cut mine, 129 separate blast patterns (consisting of 38.5 million tonnes /42.4 million US tons, equaling 28% of annual blasted tonnes) were initiated using electronic detonators. 87 patterns were designed as per site methodology using ‘vectorial’ initiation timing sequences (blast direction and relief specified only), while the remaining 42 patterns were designed with interactive initiation timing sequences - hole by hole sequencing based on the measured site specific primary shock wave (P-wave) velocity and distance between blast-holes. The intention of this project was primarily to reduce material size presented to the crushing circuit, and also to determine if productivity benefits could be obtained by the use of interactive timing."

Jan 1, 2017

By Jennifer Williams, Donald J. Berger

Originally built between 1913 and 1916, the Ashton Dam & Hydroelectric Facility has experienced various seepage and piping incidents since completion. Ashton Dam is located within 15 miles (24 km) of the historical Teton Dam failure site and about 2.3 miles (3.7 km) west of Ashton, Idaho. Numerous repairs conducted over the years ranged from filling sinkholes on the crest of the dam to placement of rockfill on the upstream slope to improve seismic stability. In addition, the existing low level outlet works was grouted full and abandoned in 1991 due to significant vibrations induced on the dam during its operation.

Jan 1, 2014

By X. Gumede

A model is being developed to quantify the benefits for mining houses resulting from the reduction in greenhouse gas and energy consumption by the application of innovative blast designs in addition to direct financial benefits throughout the mine to mill value chain. The conversion from shock tube initiation systems to electronics and some changes to powder factor measured on an open pit mine had previously been used to show significant improvement on blast outputs. Benefits were realised on drilling, blasting, loading, hauling and beneficiation. Quantification of the relationship between powder factor and reduced greenhouse gasses is investigated in this study. The study has highlighted new data that must be recorded and hence some assumptions were made as to fuel consumption and the energy in crushing was obtained from the Bond work equation. The mine to mill projects in an open pit platinum mine and a quarry produced energy savings and reduced greenhouse gas emissions associated with the careful application of explosives and blast innovations. The less fines project showed an increased carbon footprint. The model provides a new insight into how project feasibility should be decided based on economic and environmental viability.

Jan 1, 2012