Search Documents

Paper presented at the Mining Institute of Scotland's annual general meeting held in Glasgow, 8th April 1916. Although there is nothing novel or difficult about the sinking described, circular shafts are not numerous in Scotland so the details connected with such a sinking may be of interest. The shaft was sunk at Dykehead Colliery, Larkhall, which has been worked for over 50 years from the upper seams. It became necessary to sink another shaft to serve as a replacement downcast, by which the output might be maintained and some of the lower seams won. As the sandy clays regularly caused bulging into the rectangular shaft and sinking of the surrounding ground it was decided to make the new shaft circular and to enclose its mouth in a foundation-block of concrete resting on the solid clay. Details are given of the sinking, brick seating and lining, kettle strike, water-rings and doorhead lintels as well as the permanent fittings, winding gear and the cages themselves

Dec 1, 1916

By R. I. Jeffery, J. W. Summers

An account is given of the verification and calibration of a numerical modelling technique that has been developed for the prediction of subsurface strata deformation following the extraction of coal by longwall mining methods.

Jan 4, 1992

By H. B. Bell, L. C. Smith

Measurements have been made of the activity of 'FeO' in 'Fe0'-Mn0-Ti02 melts at 1475 degrees C. The results obtained are discussed in terms of ideal mixing of titanates and in terms of a regular solution model. On the basis of the regular solution model activities of Ti02 and MnO in the Fe0-Mn0-Ti02 and Mn0-Ti02 systems have been derived. The data have been shown to be consistent with the liquidus lines in the phase systems. Examples are given of the application of the data to slag-metal equilibria, being used to derive slag-metal data between liquid iron and Fe0-Mn0-Ti02 slags

Dec 1, 1971

The mineralogical composition of the ore was determined and the mineral phases with which nickel is associated were identified. The ore was prepared by grinding to -420 micrometres and classification into granulometric fractions. Prior to the main series of experiments the effect of agitation rate on nickel recovery was investigated. The influence of sulphuric acid concentration, temperature and particle size on the kinetics of nickel extraction was then studied, both quantitatively and qualitatively, over fixed value intervals. Application of the initial rate method enabled determination both of the order of reaction with respect to sulphuric acid concentration and the activation energy for the dissolution of nickel. The results indicate that a physical mechanism can be ruled out as the rate-determining step in the extraction of nickel from the ore and that a chemical mechanism is more likely

Dec 1, 1991

By R. Trueman, D. B. Tyler

Numerical modelling was used to determine the magnitude and direction of stresses around drives both adjacent to and distant from open stopes in the South Crofty tin mine. Modelling predicted that drives near the stopes are situated in a stress-relaxed zone. The peripheries of drives that are sited in solid rock away from the influence of stoping are in compression. Key-block modelling was used to determine the typical geometries of critical blocks and distinct element modelling was used to determine block stability. The conclusions derived from modelling fitted the observational data. This indicated that key-block theory is a valid tool for analysing the stability of roadways in the South Crofty mine. The support requirements for drives located next to stoped-out areas were formulated using a risk analysis approach to key-block formation. The results were compared with support guidelines derived using empirical design methods. Good agreement was obtained for the roofs of the drives but not for the sidewalls. The concept of a critical excavation width was formulated: once an excavation is larger than the critical size the length of rockbolts need not be increased as the excavtion dimensions increase. This may be the case in all rock mases.

Jan 4, 1993

By R. G. Siddall, W. Gale

In the UK the development of the science of strata control has been strengthened by a resurgence of interest in the specialism of roofbolting and its associated techniques. The evolution of the theories and practices of strata bolting in roadway stabilisation is discussed. Practical experiences are considered, principally the use of Australian techniques, the relationship between bond strength and annulus and the effects of stress in the ground. Areas of new technology such as cable bolting, injection anchors and on-board bolters are also discussed. The recent advances in computer technology and rock testing equipment and methods have provided the opportunity to simulate ground behaviour under various conditions. Computer modelling developments and the use of techniques to predict ground behaviour are described.

Jan 4, 1992

By Li Shibo, C. Halls

The compositions of olivine, pyroxene and chromite from the Proterozoic ultramafic complex are analagous to those of cumulate ultramafic rocks of tholeiitic origin, suggesting that the parent magma may have been tholeiitic rather than komatiitic. The complex contains economically significant Ni-Cu sulphide mineralisation. The high sulphide/silicate ratio is best explained in terms of the segregation of sulphides from a large volume of magma, of which all but the ultramafic cumulate fraction has since been eroded. Platinum-group minerals that have been identified include sperrylite, moncheite, native platinum, froodite, merenskyite, michenerite and Pd-rich pentlandite lamellae exsolved from pyrrhotite. They are characteristically found in close association with chalcopyrite, either along the contacts between hydrosilicate and sulphide grains or in cracks within pentlandite and chalcopyrite, which may also be intergrown with galena. Crystallisation from a Cu-rich residual magmatic liquid also enriched in Pt, Pd, As, Sb, Bi, Te, Zn and Pb is postulated.

Jan 12, 1993

The Council of the Institution of Mining and Metallurgy submitted the report of the affairs of the Institution for the session 1970-71, and the Statement of Accounts for the year ended 31 December, 1970. The statistics given in the report refer to the calendar year 1970. Details are included of membership, officers, representation on other bodies, honours and distinctions, awards, meetings, publications, library, overseas activities, fellowships and grants, the revenue and expenditure account, the balance sheet, trust fund balances, contributing companies, and schedule of investments

Dec 1, 1971

By M. J. Russell, W. E. Stephens, D. B. Mohamad, A. B. MacKenzie

Redox front processes in rocks are important in the context of both radioactive waste disposal and the development of orebodies. Results are presented from a study of the distribution of uranium and thorium and the natural decay series equilibrium about redox fronts in a granite at the Criffel pluton and Craignair quarry, Dalbeattie in southwest Scotland. The results are considered in the context of large scale uranium aqueous transport in the region and compared with those from a previous study of highly developed redox fronts at Pocos de Caldas, Brazil. Results show that the Criffel pluton has experienced a recent and rapid removal of uranium from the uppermost section of the granite whereas thorium has remained relatively immobile. The radium and uranium distributions indicate that diffusion processes probably control the distribution of radionuclides about the front. These processes are similar to those observed at Pocos de Caldas. The trends of concentration and activity ratio about the Dalbeattie redox front are less pronounced than those at Pocos de Caldas owing to the shorter time available for the process and the lower intensity of weathering at Dalbeattie.

Jan 12, 1992

By R. J. Howarth, P. L. Llowenstein

The errors resulting from field sampling, sample preparation and analysis are investigated for drainage sediments derived from homogeneous sandstone, shale, limestone, basic igneous and granite lithologies as a background to a primary reconnaissance survey of England and Wales. Emission spectrographic analyses of approximately 350 samples for Al, Ca, Fe, K, Si, Ba, Co, Cr, Cu, Ga, Li, Mn, Ni, Pb, Sc, Sn, Sr and V and atomic absorption analyses for Cu, Ni, Mn, Co, Zn and Pb have been treated statistically. For routine broad-scale surveys analysis of the unground -80-mesh sediment fraction proves satisfactory. Sampling error between localities in a stream is shown to be less than spectrographic analytical error for many of the elements considered here, except where mineralisation (contamination) occurs, but exceeds the atomic absorption analytical errors in most cases. Unless it it critical to reduce the amount of between-site variability (having regard to analytical errors) in the regional survey, there appears to be no advantage in the use of a more sophisticated sampling technique. The utility of moving-average maps in reducing the width of the confidence belt around the regional 'geochemical surface', and thus compensating to some extent for the sampling errors, is also demonstrated.

Dec 1, 1971

The following procedure was used to determine cut-off grades: define the orebody profile; plan the stope layout and quantify the work involved; formulate equipment-performance norms; calculate unit costs; input process recoveries and metal prices; and calculate the cut-off grade. Use of the method is illustrated using data from a copper mining complex in India. Results from the study led to the following conclusions for underground mines in general. Cut-off dependent costs vary significantly with the stoping method employed, orebody thickness, the degree of mechanisation and the working efficiencies of the workforce and equipment. This applies even within the same deposit. Sub-level stoping and its variants can be operated at a lower cut-off grade than cut-and-fill and its variants. Thinner orebodies affect cut-off grades adversely, but with thinner orebodies very little further reduction in cut-off grade can be achieved once a certain minimum width has been exceeded. For the same stoping method and in the same mine the cut-off grade varies with the degree of mechanisation. Labour-intensive methods require higher cut-off grades. An allowance for working efficiency should be made when calculating cut-off grades. Higher process recoveries allow a significant lowering of cut-off grades

Jul 1, 1996

By Q. H. Liao, B. G. Monaghan

The options for designing slopes in complex geological conditions are reviewed. It is shown that modelling, especially numerical modelling, allows a degree of analysis that cannot otherwise be achieved. Examples are presented of how numerical modelling can be used to investigate fundamental aspects of rock mass behaviour. It is demonstrated that an important consequence of change in scale is that the mechanisms of failure also change. The complex failure of the footwall slope at Aznalcollar, a large open-pit mine in southern Spain, is discussed. Numerical modelling with UDEC (universal distinct-element code) has allowed the realistic simulation of displacements measured in the field

Jun 18, 1905

By K. C. Dunham, M. Solomon, T. A. Rafter

Sulphur isotope ratios have been determined for 81 sulphides and S and O isotope ratios for 26 barites from the Alston Block in the northern Pennine ore field. In addition, both isotope ratios have been determined for 29 evaporitic anhydrites of various ages from European and Australian localities. The consistency of the sulphate isotope ratios over a wide area of the northern Pennines, and their similarity to values for Lower Carboniferous evaporites, suggests that the sulphate originated from Lower Carboniferous connate waters. It is suggested that these mingled with warm brines rising through granitic plutons beneath Tynehead and Upper Weardale, the aqueous sulphide ion in these brines having a delta34S value of approximately +10 per mille. The delta34S values for the sulphides range from +15.0 to -5.9 per mille and show an outward zoning with higher values in the central fluorite zones and mainly negative values in the outer barite zones. The wide range of delta34S values for the sulphide S is not characteristic of magmatic S and there is no adequate local source in the Carboniferous sediments. It is suggested that formation waters, probably mainly of connate origin, sank down sufficiently deep to become heated above 200°C before rising through Caledonian granite plutons into the Carboniferous sediments, where they spread laterally to mingle with cooler sulphatic connate water. The rising fluids were hypersaline brines carrying F, Ba, Pb, Zn, Cu and S. Temperatures of deposition calculated from galena-sphalerite isotope fractionation are similar to temperatures previously determined from fluid inclusion studies.

Dec 1, 1971

By C. M. Lesher, R. R. Keays

"The komatnte-associated Fe-Ni-Cu sulphide mineralization at Kanihalda, Western Australia, is generally believed to be magmatic in origin, but a number of postmagmatic processes significantly modified the original distribution, structure, texture, mineralogy and chemistry of the ores. Two important types of mobilized magmatic sulphides are interpillow/interbreccia sulphides and hydrothermal vein-type sulphides. Interpillow and interbreccia sulphides occur interstitial to pillowed or volcaniclastic footwall metabasalts beneath or adjacent to the stratiform contact ore horizons. They are mineralogically and compositionally similar to massive ores (and are similarly depleted in PGE relative to the compositions of bulk samples of mined ores), but normally do not contain the distinctive chalco-phile ferrochromites characteristic of contact ores. They are interpreted as magmatic sulphides that have been mobilized from the overlying or adjacent massive sulphide layer during peak tectono-nietamorphism.Hydrothermal sulphide-quartz + albite veins also occur in the footwall metabasalt and contain unannealed deformation fabrics indicative of emplacement during retrograde metamorphism. The high Ni and Pd contents of these sulphides (7-13% Ni, up to 70 ppm Pd) indicate that the metals have been derived from the spatially associated komatiites and/or contact ores, consistent with the Pd depletion previously inferred for massive ores. Very low Ir contents and high Pd/Ir ratios of the vein-type sulphides confirm an aqueous transportation-deposition mechanism; hydrothermal transfer of PGE results in strong decoupling of Pd from Ir.There appears to be a complete continuum of sulphide mobilization at Kambalda ranging from whole-scale phy sical dislocation (fault offset ores) and selective mobilization (stringer sulphides) through nietamorphie replacement (interpillow/interbrec- cia sulphides) to jiydrothermal dissolution and redeposition (vein-type sulphides)."

Jan 1, 1984

By A. H. G. Mitchell

Gold-poor and gold-rich porphyry and epithermal gold-silver deposits of Caenozoic and Cretaceous age in the western Pacific and central and eastern Europe are confined to predominantly andesitic continental margins and island arcs. The arc volcanic rocks overlie a complex non-oceanic basement of stacked nappes, the uppermost of which is often ophiolitic. The emplacement of ophiolite triggered a reversal of tectonic polarity, subduction and arc magmatism. Andesitic volcanism and the formation of a strato-volcano were followed by the ascent of magma and porphyry copper mineralisation. Regional propylitic alteration came from convecting, predominantly meteoric fluids. Magmatic degassing caused advanced argillic alteration. This is commonly unmineralised in perched water tables, but may sometimes host high sulphidation gold or enargite gold at deeper levels within the propylitic zone. The onset of extensional stress after the andesitic volcanism allowed meteoric water to circulate to depths of 5 km or more, with consequent cooling of an ascending magma body at depth and the development of low sulphidation epithermal gold mineralisation near and immediately above the sub-volcanic basement surface. All andesitic arcs are mineralised. Regional controls on their ore potential include the level of erosion and geological features in the basement that focus the ascent of fluids. Differences between the mineralisation of the European and the western Pacific arcs may reflect the presence of older, more granitic basements in many of the European arcs.

Jan 12, 1992

By J. Cech

Discussion is presented of a decision-making support method for the spacing of ore passes along a long vein orebody and the division of the orebody into convenient stopes for future mining operations. The method was tested on a Slovak siderite deposit and also on some hypothetical cases with the objective of obtaining more general results

Jun 18, 1905

By P. Rama Krishna, B. Narasimha Rao, P. Ali i Peera

Induced polarisation (IP) surveys are commonly used in uranium exploration programmes in India. The IP method is effective in detecting the disseminated metallic sulphides that are often associated with uranium minerals. However, conductive and polarisable host rock or overburden often introduces inductive or electromagnetic (EM) coupling into time domain IP measurements. This makes it difficult to distinguish between responses due to such coupling and those that might indicate economic mineralisation. Attempts must be made to remove the EM effects before the IP technique is used in drilling programmes. Transient decay curves which were recorded during field surveys at Pisnari were factorised using the Marquardt algorithm. Dispersion plots of the amplitudes and relaxation times of the composite exponential function enable a clear distinction to be made between the effects of EM coupling and those of mineralisation.

Jan 4, 1993

By D. J. Reddish, B. N. Whittaker, G. X. Sun

An image analysis technique has been used in the assessment of subsurface fracture levels in the context of water inflow into longwall mine workings. The technique was used to analyse results from physical modelling which are represented by black and white photographs taken directly from the model tests. Binary images of fracture patterns are obtained by scanning the photographs with an image analyser coupled to a video camera. The images are manipulated by a C program which allows them to be processed in vertical and horizontal directions and filtered to differentiate quantitatively between vertical and horizontal fracture intensities. The fracture density distributions provide a valuable database for further numerical and statistical analysis. This allows assessment in terms of water inflow into the excavation. A comprehensive image analysis was undertaken on several extraction models. Results indicate that extraction thickness has a significant effect on the fracture pattern and the fracture density distributions. The results can be used to adapt model findings to situations with a range of extraction thicknesses. The technique has allowed improvement in image enhancement and in the interpretation of model results. In particular, a qualitative comparison between different models is possible.

Jan 12, 1992

By L. J. Barnes, R. O. Koch, J. H. Versteegh, C. J. N. Buisman, P. J. H. Scheeren

Several water treatment options have been studied and piloted. A process based on activity of sulphate reducing bacteria combines sulphate removal and heavy metal removal in one process step. The anaerobic bacteria reduce the sulphate to sulphide and consequently metal sulphides will precipitate. The final design for the commercial scale plant is described.

Jan 12, 1992

By M. A. Bussell, G. S. Camm

The study included lode zones at Wheal Pendarves, South Crofty and Rosevale tin mines. Fluid inclusion-containing microfractures are a common feature of the granites and typically show a preferred orientation over quite a large area. The close proximity of a dominant vein or fault controls their density and orientation. They are important pathways for fluids and provide a marker for palaeo-fluid flow. Overprinting provides a reliable representation of the evolution of the hydrothermal fluids in a vein system from early magmatic fluids to late-stage meteoric and basinal brine input. Measurement of microfracture orientation allows estimation of the regional stress regime during a specific hydrothermal event. Since micro- and macro-structures can generally be reliably correlated, these studies assist in modelling the detailed development of complex vein systems. Microfracture density is a good measure of palaeo-permeability, with implications for control of wallrock alteration. The determination of the location and density of microfractures can assist the mine geologist in identifying the location of potentially economic vein structures where macroscopic markers are absent

Aug 1, 1996