Search Documents

By Darryel Boucher, Raymond Langlois, Neil Rowson, Kristian Waters

The Knelson Concentrator is a centrifugal gravity concentrator composed of a high speed rotating bowl into which a mineral slurry is fed. The rotational motion creates a centrifugal acceleration up to an equivalent of 200 G. Under this acceleration, particles enter fluidised riffles along the side of the bowl, with the fluidisation allowing for the substitution of dense material for less dense. The separation mechanism is not fully understood and questions remain on the optimal residence time, slurry feed parameters and bowl surface profile to achieve a better separation. The positron emission particle tracking (PEPT) technique has been applied to record the motion of a -1700+1180 µm particle of a quartz-gold matrix, labelled with 18F radioisotope while it undergoes concentration inside a 3" laboratory scale Knelson Concentrator (KC-MD3) operated at 60 G. The slurry used was composed of quartz and magnetite. Particle trajectories during the first stage of the concentration process where the heavier particles centrifuge through the increasingly dense slurry towards the riffles of the bowl are shown with respect to time. This work reveals new information on particle motion inside the Knelson Concentrator and the results will be used for validation of developed separation model as well as optimisation of a centrifugal concentrator’s performance.

Jan 1, 2014

By I. Zimbovski, T. Ivanova, E. Chanturiya

"The mechanism of selective action of new reagent-collector AMD of phenylpyrazolone class with sulphide minerals of copper-zinc ores was theoretically and experimentally investigated. The validation was carried out using spectrophotometry, Fourier-transformed spectroscopy, laser scanning microscopy, analytical scanning electronic microscopy and flotation. The reagent AMD in alkaline medium on chalcopyrite and sphalerite surfaces is chemically sorbed, forming strong hydrophobic complexes with copper and zinc. On the pyrite surface, AMD acidifies ferric iron ions with formation of hydrophilic oxidates. The selectivity of collector AMD with separation of sphalerite and pyrite in alkaline condition (??=10) is confirmed by flotation experiments. With AMD, the obtained recovery of sphalerite was 34.4 % at extraction of pyrite of 3 and 6 %. The low recovery of sphalerite is caused by weak collective ability of the reagent. The use of copper sulfate increases the flotability of sphalerite up to 82.0 % at extraction of pyrite of 5 and 2 %. It has been experimentally determined that during the flotation of sphalerite and pyrite by AMD reagent with addition of butyl potassium xanthate, and in the presence of copper sulfate and regulator of formation of ammonium thiocyanate complexes, the recovery of sphalerite is increased to 91 %, while the recovery of pyrite is decreased to 3.8 %. The chalcopyrite is floated actively (90 % recovery). The results of all theoretical research and experiments were confirmed by flotation tests on ores and products of dressing in industrial conditions."

Jan 1, 2014

By D. Tang

The froth zone in a flotation cell is recognised as a region which contributes to the overall flotation performance. Froth recovery is a measure of the efficiency with which the froth phase delivers particles arriving at the pulp-froth interface to the concentrate. Poor froth recovery in scavenger stages is generally attributed to poor froth stability. The key indicators of froth performance: froth recovery, entrainment and water recovery were measured in an OK3 pilot cell installed at a zinc concentrator in Australia and supplied with scavenger feed. Cell hydrodynamic and pulp chemical conditions during the operation of the cell were also measured as well as bubble growth across the froth phase. The objective of the work was to assess the impact of a number of commercial frothers on the froth performance in the OK3 cell and assess the suitability of using bubble growth as an indicator of froth stability.

Jan 1, 2014

By M. Kadiyski, V. Stoyanova, E. Visariev, V. Stoilov

"The present study deals with copper losses in slag from copper smelting. Copper slag cooling at Aurubis Bulgaria is traditionally done in pits. A new type of slag-cooling is introduced in the site, involving cooling ladles. In a previous study, the ladle cooling process was studied in detail, showing an improvement in the recovery of copper in the slag after flotation. The main reason for better recovery of copper is the increased cooling time, which allows for the accumulation and aggregation of copper droplets. The effects of the newly introduced slag cooling process are studied using optical microscopy and scanning electron microscopy. Cooling in pits and in ladles is compared, based on copper droplet size, distribution and content. Specialized image processing software is employed on images taken with an optical microscope. The results are then compared with a similar technique, available in SEM software. The availability of phase-analysing image software in combination with electron dispersive X-ray spectroscopy makes it possible to study the morphological properties, distribution and chemical composition of the copper droplets. The obtained results confirm the initial conclusions about size, distribution and composition of the copper-bearing particles. A large amount of copper particles is examined showing an obvious increase in their size from pit- to ladle cooling. The results show an increase in the average size of the droplets, which doubles from pit-cooling to ladle-cooling. There is a well-pronounced tendency of decrease of the percentage of droplets in the smallest fraction (<5 µm) in the ladle-cooled slag. In addition, the number of droplets in the larger fractions increases, compared to the ones in the pit-cooled slags. It is believed, that the developed methodology for analysis provides a relatively quick and reliable solution for comparison of the cooling rates in the slag. INTRODUCTION In the process of copper smelting and converting, iron-silicate slags are produced that contain various amounts of dissolved and entrained copper. Different physical and chemical techniques are employed for the valorisation of the remaining metals in the slag – magnetic separation, leaching, roasting, flotation, etc. According to Gorai et al (2003), about 2.2 tons of slag is produced per ton of metal. In 2016, about 20 million tons of copper have been produced globally (www.icsg.org). At an average of 0.5 percent copper content after treatment, these slags contain more than two hundred thousand tons of copper which is lost due to inefficient processing."

Jan 1, 2018

By Girolamo Belardi, Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

Ore textural and structural characterizations play a fundamental role in any preliminary study (i.e. comminution, classification, separation) addressed to the design and set up of beneficiation flow sheets. The possibility to utilise automatic tools able to perform a classification, and a quantitative description, of the mineralogical and petrographical characteristics of raw ore samples thus represents an important step to define, to control and to verify the entire set of parameters, ore-texture-related, that can affect the final beneficiation results. The procedure usually adopted is based on the analysis of polished sections and more in details the recognition of the different mineralogical species and associations and the measurements of some quantitative parameters estimating both the geometrical characteristics of each species and the possible spatial relationships between them. This approach, originally carried out by experts, utilising optical and/or electronic microscopy, was ‚replaced? during the years by more and more sophisticated devices integrating analytical facilities and acquired data processing. Such integrated analytical devices formed the breakthrough platforms into what is now known as modern Process Mineralogy. In this paper the possibilities offered by chemical imaging based devices and techniques, to perform ore minerals recognition/classification, and to perform their topological assessment, are presented. Tests have been carried out and are discussed in order to analyze the problems related to the development of suitable and low cost strategies addressed: i) to realize a full mapping of ore minerals/gangue inside selected samples, ii) to define the optimal data-flow handling to optimize the speed of processing versus the quality of the results and iii) to start to define logics and procedures finalized to implement innovative smart detection engines, chemical imaging based, for mineral processing addressed to perform both a preliminary characterization of the ore, at laboratory scale, and a further possible control of the different processed minerals flow streams.

Jan 1, 2014

By J. T. Liu

Packing in a flotation column is one way to increase separation efficiency and effective descending flotation-column height. In this paper, the difference between filling packing and sieve packing is described, and the flaws of filling packing in flotation columns in industrial application are pointed out. A change of flotation process and its effect on flotation results are reported. Based on sieve-plate filling, a high-efficiency mixed packing mode consisting of screen-plate packing and honeycomb-tube packing has been proposed, with the packing mode optimized in the cyclonic static microbubble flotation column in the separation zone. In the mixed packing mode, the honeycomb tubes are used to reduce the vortex effect at the base of the column and weaken the radial dispersion of jetting bubbles, and the sieve plates are used to comminute bubbles in the separation zone, to lengthen the bubble migration path, and to stabilize the foam layer. The superiority of honeycomb-tube packing is analyzed using bubble-particle collision theory, and the dynamic equations of collision probability are derived. The role of mixed packing in guaranteeing mineral recovery is analyzed by the axial dispersion method, and a dimensionless axial dispersion model is derived. When a high-turbulence flow is maintained, a static separation environment is formed in which secondary mineral processing is rendered more effective. In this way, a nonlinear separation environment is formed in the flotation column. Finally, mixed packing was applied in an industrial test. A large vortex developed at the base of the column. It was observed that the bubbles in the radial flow were homogeneously dispersed, the residence time of the pulp was prolonged, and the froth layer became thick and stable. Based on the test data, it was found that the sieve packing has the potential to yield a product of approximately 25.83% copper concentration with 91.78% recovery from a feed concentration of approximately 0.727%. If mixed packing were used, the product concentration could be further increased to 27.60% from a feed of approximately 0.739% concentration with 93.38% recovery.

Jan 1, 2014

In many base metal sulphide concentrators reagents such as collector and cyanide are often added to the grinding mill as well as to the flotation circuit. Whilst good reasons can be cited for splitting the reagent addition in this way, the benefits of such are rarely quantified and the complex reagent-mineral-media interactions occurring during milling are often poorly understood in terms of pulp chemistry. A new laboratory batch grinding mill designed by Magotteaux allows the user to measure, monitor, and control the pulp chemical conditions during grinding when testing different ores and media. Some of these parameters include pulp pH, pulp Eh, temperature, gaseous atmosphere, and dissolved oxygen concentration. In a recent development, the mill has been coupled with a simple on-line reagent monitoring system, designed by CSIRO, which allows the levels of species such as xanthate and cyanide in the grinding pulp to also be measured continuously during milling using a robust UV detection system. In this way the uptake of collector during grinding and the rate and ex-tent of cyanide interaction with the minerals and media can be determined as a function of grinding time. A series of grinding tests using an Australian nickel sulphide ore was conducted with the coupled system in which the cyanide dose, xanthate dose, and media type were systematically varied. The xanthate and cyanide levels were monitored as a function of grinding time and the data collected are discussed in terms of the pulp chemistry of the system and implications for plant reagent dosing strategies.

Jan 1, 2014

A processing scheme is presented to use one single chemical that has multiple functions to re-duce the use of chemicals and achieve more efficient mineral flotation and solids dewatering. Sti mulisensitive polymers which display hydrophilic/hydrophobic transitions in response to changes in temperature or pH have been found to be useful as such multiple function reagents. They can cause the mineral particles to be either hydrophilic or hydrophobic at one stimuli condition and the opposite at the reverse stimuli condition. Therefore, both particle surface wettability and inter-particle interaction forces are reversibly controllable. When the surface is hydrophilic, particle dispersion is achieved by repulsive inter-particle forces whereas when the surface is hydrophobic, particle aggregation is induced by inter-particle hydrophobic attractive forces. In addition, the hydrophobic surface condition allows for the attachment of particles to bubbles. Flotation and solid settling tests have been conducted with a silica suspension treated with the temperature-sensitive polymer poly (N-isopropyl acrylamide) (PNIPAM). The results indicated that PNIPAM can be used to induce a transition between hydrophilic and hydrophobic surface character at temperature lower or higher than its critical solution temperature (CST around 32oC). Thus, both effective silica dispersion or hydrophobic aggregation and flotation without adding any additional collector have been demonstrated. In tailings treatment, rapid silica settling was obtained with hydrophobic aggregation at temperature above the CST and further sediment consolidation (and water release) occurred at temperature below the CST. Contact angle measurements confirmed the hydrophilic/hydrophobic transition induced by PNIPAM.

Jan 1, 2014

By Z. Chen

This study is concerned with the behavior of bubble clusters in a well-controlled turbulent flow. We used a specially designed cell where the bubble aggregates could be formed and exposed to breakage by a rotating impeller. The effects of impeller speed and the concentration of collector on cluster behavior were studied. It was found that the size of the clusters increases with the concentration of collector used. We also found that although the clusters could easily be destroyed under the action of impeller, they could reform, especially at lower impeller speeds. It was observed that the size of the bubbles arriving into the impeller region in the absence of particles before breakage was considerably higher than the size of the clusters formed at the same impeller speed. It appears that both cluster breakage and re-formation take place simultaneously, and the extent of formation and regrowth is mainly determined by the hydrophobicity of the particles and the impeller speed.

Sep 1, 2012

By Sarthak Kaushik

Zeta potential measurements show that the isoelectric point of crandallite, in aqueous solution of 10-2 N sodium chloride is at about pH 5.5. Measurements of turbidity confirm the point of zero charge or crandallite. Calcium ions specifically adsorbed on the surface and thus changed the zeta potential and turbidity. From the measured data, it is confirmed that starch acts as a flocculent for crandallite. Oleic acid, which is a collector used in phosphate ore processing is weakly adsorbed on the surface of crandallite. This results in hydrophobic coagulation of particles resulting in a lower turbidity.

Sep 1, 2012

By Lucy van de Ruit, Megan Becker, Aubrey Mainza, Jenny Wiese

"UG2 chromitite ore is a complex, highly disseminated platinum ore from the Bushveld Complex in South Africa, with typical platinum group mineral (PGM) grain sizes below 15µm. The introduction of stirred mills to the platinum industry has enabled grinding to finer product sizes, which has improved liberation and recovery of the finely grained PGMs. However, reduction in particle size leads to an increase in chromite entrainment in the flotation concentrate, which has a negative impact on the subsequent smelting process. Factors such as particle size, froth structure, solids concentration and water recovery have all been identified as impacting entrainment, but whether particle shape also has a significant effect is unclear. The purpose of this study was to determine whether the recovery of chromite particles by entrainment during the flotation of UG2 ore is affected by particle morphology. A laboratory vertical stirred mill with inert ceramic media was used for grinding UG2 ore which was then floated in a batch flotation cell. Flotation feed and concentrate samples were analyzed using QEMSCAN to quantify the angularity and aspect ratio distributions of the particles. The stirred mill product was found to have relatively broad aspect ratio and angularity distributions, with the major mineral components (chromite and silicates) having very similar shape characteristics. Analysis of flotation feed and concentrate samples suggested that particle shape does not have a significant effect on chromite entrainment."

Jan 1, 2014

By G. G. Xiong

Water-sealed cyclone is a new efficient equipment to use for grading,concentrating of slurry, it was researched and developed by the Kunming Metallurgy Research Institute in the 1980s , and ac-cessed to the 1990 national invention award and the national patent products (ZL02245313.X ). The equipment and technology are innovative, firstly, we design a set of micro-pressure (0.005~0.008MPa) water-sealed device, which eliminates the gas phase of three-phase of sol-id-liquid-gas of the traditional general hydrocyclone grading process, it only has solid and liquid phases. Secondly, the axial velocity envelope surface which is a factor of controlling the accuracy of grading changes to a wedge rotation; and the interface of upward flow to down flow changes from surface to the solid, it can improve grading accuracy. Thirdly, water-sealed box and catheter devices make the stilling which pass through the cyclone cone centrifugal force fields re-enter the pressure grading zone of catheter. The three innovations make water-sealed cyclone can reduce the loss of overflow and has less mud in stilling product. Because the excellent performance, the water-sealed cyclone has application in non-ferrous metals, ferrous metals, non-metallic and aluminum hydroxide industries for grading, desliming and concentrating since it has successfully developed.

Jan 1, 2014

By B. Suresh

Iron ore in Bellary-Hospet region is friable in nature and generates a significant amount of micro-fines (-150 µm) during mechanized mining, handling and processing. Present beneficiation practice generally employs spiral classification followed by hydrocycloning to remove slimes (-15 µm). The iron ore fines, beneficiated at JSW Steel Ltd., Karnataka generates tailing having 48-52% iron content in the form of slimes, which accounts for 50 to 55% by weight with respect to classifier overflow. The loss of iron as slime is considerably high. In this context, laboratory studies were carried out with different combination of beneficiation techniques with an objective to develop an efficient flow sheet to achieve better product grade and recovery from classifier overflow. The results revealed that de-sliming process by hydrocycloning in combination with either magnetic separation or froth flotation leads to increased iron loss in tailing. Based on investigation it is observed that forward flotation is beneficial over the reverse flotation. The experimental approach of forward flotation on classifier overflow followed by magnetic separation on flotation tailing resulted in overall product grade of 62.9% Fetotal and 70.3% yield. The tailing contains 34.6% iron, which accounts for 29.7% by weight with respect to classifier overflow.

Sep 1, 2012

The Sydvaranger magnetite mine was shut down in 1996 due to low iron ore prices. It was reopened in 2009. The flowsheet has remained more or less as in the old plant, based upon two grinding steps followed by magnetic separation. The Sydvaranger magnetite is free of harmful elements and should therefore be sold on the high quality market. This requires a concentrate containing less than 2 % SiO2. In the old plant, this grade was achieved by amine flotation. Amine was preferred as collector because it could be used in process water from the sea. The use of amine has been restricted by the Norwegian pollution authorities during the time the mine was shut down. Test work to replace cationic with anionic flotation is therefore done. Research on activation of quartz with Ca or Mg ions prior to anionic flotation was shown by basic research in the period from 1960 to 1980 to be effective under simplified laboratory conditions. This old research has now been followed up from a practical/empirical point of view. The basic work was mainly done on quartz and iron minerals only. In this case, an actual feed containing a number of minerals common in iron ores is used, in order to demonstrate that a commercial process is possible. Calcium activation is shown to work excellently but requires too high pH to be environmentally and economically attractive. Magnesium activation is a more difficult process, because the maximum concentration of MgOH+, which was shown to be the activator, is about 100 times lower than the alternative CaOH+. Flotation success depends partly upon the ore, some amphibole minerals are more difficult to float than pure quartz. Ordinary batch flotation test work is time consuming. A South African microflotation test cell has shown promise, because work can be focused upon flotation of the more critical coarser fractions of the Sydvaranger ore. Keywords: iron ore concentration, anionic flotation, mineral activation, microflotation, Sydvaranger

Sep 1, 2012

By C. Y. Wang

Based on Slurry Electrolysis, and combined with the problems of extraction antimony, lead and their separation from complicated antimony-lead concentrate, a series of tests have been done in this paper. Using Slurry Electrolysis to treat complicated antimony-lead concentrate, antimony and lead can be separated in one step. And 2# metal antimony can be achieved in cathode directly at the same time. Lead in concentrate is restrained still in the residue at the form of PbCl2. After converting the residue with ammonium carbonate and removing sulfur with kerosene, the high quality of lead concentrate (Pb is above 45%, S is below 15%) and pure sulfur can be achieved, respectively. The recovery of all in Slurry Electrolysis process is as: Sb 95%, Pb 95%, Ag 80%, S 60%.

Jan 1, 2014

By S. C. Borah

Graphite, a mineral form of pure carbon, is one of the most versatile minerals in industry, because of its varying physical properties and characteristics. The mineral occurs naturally in the form of tubular crystals or microcrystalline earthy lumps, or it is disseminated in rocks, which have undergone intense metamorphism. India has a large deposition of graphite minerals out of which about 43% are found in Arunachal Pradesh. However, compared to the rest of the country, the North-East Region and particularly Arunachal Pradesh has not attracted attention till date for detail investigation for characterization, beneficiation, prospecting and/or exploitation of the mineral resources including graphite. Bulk graphite sample were collected from upper Subanshiri district of Arunachal Pradesh. Chemical analysis of the representative samples were carried out and found that 7.29%, 19.60% and 6.07% of fixed carbon (FC) is present in graphite sample collected from La-Lamdak, Bopi and Taliha, Arunachal Pradesh, respectively. Chemical analysis of the ash of the graphite sample shows presence of impurities such as silica, Al2O3, Fe2O3, Ca, Mg etc in the graphite sample which are also supported by XRD and SEM-EDX investigation. The graphite samples of Arunachal Pradesh are low grade and do not fulfill the market requirement for the industrial applications. Therefore, low-grade graphite is subjected to beneficiation for the upgradation of the graphite for industrial applications. We have adopted the dispersion?cum-settling technique for the beneficiation of the graphite sample collected from Arunachal Pradesh. The FC of 40.21% with 41.17% raw graphite recovery which is equivalent to 71.02% carbon recovery have been obtained by gravity separation technique using only distilled water without any chemical reagent in case of graphite sample collected from Bopi, Arunachal Pradesh. The graphite sample is upgraded up to 47.75% FC with 41.91% raw graphite recovery, which is equivalent to 85.85% carbon recovery with the pH adjustment at 9 with NaOH. Keywords: graphite, beneficiation, gravity separation, arunachal Pradesh

Sep 1, 2012

By G. Bonifazi

Mining activities belong to human history, they are lost in the mists of time. They usually impact on large portions of the territory, both directly (exploitation areas and logistic activities directly related to exploitation) and indirectly (exploited material handling, processing and storage areas). As a result, at the end of mine life cycle, dismissed areas usually cannot be directly re-utilized without efficient and well addressed rehabilitation actions. Main goal of the proposed approach was to analyze the results obtained when a set of procedures, based on the collection and the analysis of remote sensed data, is developed to evaluate the effect of rehabilitation of land contaminated by extractive industry activities and to perform a monitoring and registration of the environmental impact of such operations by the application and the integration of modern information technologies, as Earth Observation (EO) and Geographic Information Systems (GIS). The study was developed in the framework of the EU-Asia program of the European union (EXTRACT-IT Project-Contract No: CN/ASIA IT&C/006 (89870): Application of Information Technologies for the sustainable management of Extractive industry activities) and it was addressed to three different dismissed mine areas in India, Thailand and China, respectively. The results, in terms of methodologies selected, strategies applied and results obtained, are described with particular reference to Fuxin coal mine area in China.

Jan 1, 2014

By R. K. Rath

The low-grade iron ore sample contains both lumps and fines. It is mostly hematitic iron ore and considerable amount of goethitic/limonitic material is present in it. The major impurities present were quartz and clay. It is observed that the iron bearing phases are poorly liberated above 300 µm and the liberation improves below 300 µm. More than 80% liberation is achieved below 106 µm. Based on the liberation data, the feed for the different beneficiation methods was prepared by stage crushed the ROM followed by grinding passing to 106µm and the ground material (-106µm) was deslimed. The underflow was subjected to various beneficiation techniques such as tabling, enhanced gravity separator (EGS), wet high intensity magnetic separation (WHIMS), and flotation and the results are discussed. All the methods studied could able to produce pellet grade concentrate with iron content of 64.5%, however, a marginal higher yield was observed for WHIMS (81%). Keywords: beneficiation, gravity, magnetic, enhanced gravity separation, flotation, low-grade iron ore, desliming

Sep 1, 2012

In the present work, the flotation behaviours of zircon, rutile and ilmenite using sodium oleate as collector in absence and presence of depressants were thoroughly investigated. The maximum in the flotation recovery of any of the above minerals falls within similar pH ranges. A range of inorganic and polymer depressants were examined in order to improve the separation of zircon from rutile and ilmenite. Optimum values of conditioning pH and depressant concentration to achieve maximum recovery and best selective floatability of zircon were obtained. Selective flotation of zircon from Ti-bearing minerals was anticipated from single mineral experiments under different pH values, depressant and collector conditions.

Jan 1, 2014

By M. Wierink

The lifecycle of a resource, specifically a metal, is often depicted as circle from primary production from mining to minerals processing and via manufacturing and use to disposal and recycling. When a material is recycled, it is considered as saved energy compared to producing the material from primary source. This is, however, a simplified representation. At each step of the life cycle, there are changes in the quality of the material due to different materials chemical and physical interaction, phase transformations due to diffusion, radiation etc. Due to these physical and chemical phenomena there are losses of material, which as determined by thermodynamics are not recoverable within the life cycle. This can be considered as an increase embodied energy per mass unit of substance and loss exergy from the material cycle. With low cyclic loss, the material will remain in the recycling loop for a long time, while with high cyclic loss it will disappear fast. Where you put the material determines how fast it disappears from the resource cycle. In this research paper the phenomena of quality degradation of material and idea of increase of embodied energy and exergy loss within a resource cycles is portrayed. The cyclic nature of material states and transitions and energy consequences of material quality degradation as well as the parameters affecting the length of the time scales of the material cycles are described. Currently the cyclic embedded energy and the history of material is not taken under consideration in generic life cycle assessment. This easily results into a conclusion that lifetime of product is optimized only in terms of how much energy an appliance uses during its lifetime, while ignoring the loss of embedded energy due to the effects caused by the environs the material is subjected to during the cycle. Better description of the time properties of material give us a possibility to design toward optimum lifetime of products in terms of resource efficiency. Keywords: product lifetime, material lifetime, recycling, cyclic resource efficiency, material state, material quality, exergy, embodied energy

Sep 1, 2012