Search Documents

By Sven Petersen

In April 2010 three REMUS6000 series autonomous underwater vehicles (AUVs) have been used to simultaneously map large areas near the Mid-Atlantic Ridge (3°N) axis in water depths ranging from 1,000m to 4,000m. One vehicle was provided by the Leibniz-Institute for Marine Science, IFM-GEOMAR (Kiel, Germany) the other two were provided by the Waitt Institute for Discovery (La Jolla, USA) and managed by the Woods Hole Oceanographic Institute (USA). The REMUS6000 vehicles, manufactured by Hydroid Inc. (USA), are "cigar-shaped" vehicles (4m long and weighing approx. 900kg) and consist of a tapered forward section, a cylindrical midsection and a tapered tail section. An internal titanium strongback, which extends through much of the vehicle length, provides the structural integrity and acts as a mounting platform for syntactic foam, equipment housings, various sensors and release mechanisms. The AUVs can be used in various payload configurations such as multibeam bathymetry, electronic still camera, or subbottom profiler. For these missions the electronic still camera configurations was installed. An EDGETECH 2200M dual frequency (120/410 kHz) side scan sonar was used to map the seafloor, but other frequencies are readily available for more options in resolution and range. The 120 kHz side scan transmitter was used for most missions in order to map large areas (increased range) and to be able to fly at higher altitudes (between 70m and 90m) above the rough seabed encountered in this area. The maximum slant range was between 600m and 700m on both sides resulting in a swath width of up to 1.2 km. Line spacing ranged from nearly 1,000m in flat areas down to 400m in steep terrain. Side-scan mosaics were generated with a 1m resolution. Selected areas were targeted by the higher resolution 410 kHz transmitter as well as by bottom photographs flying as low as a few meters above the seabed. The vehicles navigated autonomously using a combination of inertial navigation (Kearfott T-24 or T-16 INS) and long baseline acoustic navigation by computing their range to two moored acoustic transponders. Working efficiently in this rough topography at speeds above 3 knots was only possible due to the obstacle avoidance capabilities of these AUVs.

Jan 1, 2011

By Jai-Woon Moon

Lemkein seamount located in the west of the Kuwajleen Atoll of RMI is a relatively samll, simple-shaped, peaked type seamount with its base at 4,500 m and summit at 1,452 m water depths. Ferromanganese crusts were identified in the water depth range between 2,000 m and 2,500 m, and they were mostly observed on the northern slopes of the seamount. Among various substrate rocks, breccia occurred most commonly with crusts and formed the thickest crust layers. Average thickness of the Lemkein crusts was about 5 cm. Their chemical compositions were similar to other crusts found in the RMI area; Mn=25.82%, Fe=15.29%, Co=0.74%, Ni=0.56%. Lemkein crusts were characterized by their four distinctive internal layers; 1) Massive Layer 1; 2)Porous, Fe-stained or sediment infilled Layer 2; 3) Massive to slightly porous Layer 3; and, 4)Massive, Dense, Phosphotized, CFA veined Layer 4. Layers 1 and 2 were generally similar in composition, but highest Co concentrations were measured in Layer 1 while relatively higher concentrations of Al, Rb, Fe, and Ti were observed in Layer 2. Layer 3 showed higher concentrations of Ca and P than Layers 1 and 2. Based on the Co-chronography, the age of Layer 1 is 0¡?6 Ma (growth rate = 1.50 mm/Ma), Layer 2 is 6¡?15 Ma (1.75 mm/Ma), Layer 3 is 15¡?27Ma (1.76 mm/Ma), and Layer 4 is 27¡?45 Ma (2.06 mm/Ma). These preliminary results indicated that high Co contents in Layer 1 resulted from slow growth rates; Layer 2 was formed under relatively strong influence of high terrestrial input; and, Layer 3 was probably affected by a minor phosphatization event occurring in 15 Ma.

Jan 1, 2000

By Cornel E. J. de Ronde

Brothers volcano (34°51.7?S, 179°03.6?E) is a large caldera volcano that forms part of the active Kermadec arc south of 32° S, NE of New Zealand. It is an elongate edifice striking NW-SE that is ~11-13 km long by 7-8 km across. The caldera has a basal diameter of 3-3.5 km and is surrounded by 350-450 m high walls with the floor 1,850 m deep. A volcanic cone of dacite composition rises 350 m from the caldera floor and partially coalesces with the southern caldera wall. Much of the caldera construction and the location of the hydrothermal vent sites are controlled by intersecting basement structures. Three hydrothermal sites have been recognized at Brothers; NW caldera, SE caldera and cone. Multiple hydrothermal plumes were mapped from the bottom of the caldera upwards to a depth of 900 m and originate from two of the sites; one on the NW caldera wall the other atop the cone. Analyses of these plumes show that the two vent sites are chemically distinct. The cone site itself hosts three distinct vent fields (summit, upper flank, NE flank) that in 1999 had plumes (mainly from the summit) containing relatively high concentrations of gas with a shift of -0.27 pH units (proxy for CO2) and H2S concentrations up to 4,250 nM, particulate Cu (PCu) of 3.4 nM, total dissolvable Fe (TDFe) of 4,720 nM, TDMn up to 260 nM and Fe/Mn values between 4.4 and 18.2. However, in 2002 plumes from the summit vent field had noticeably lower concentrations of PCu (0.3 nM), TDFe (175 nM), and Fe/Mn values of 0.8, although similar TDMn (220 nM) and shift in pH (-0.22) suggesting a state of flux for this site. By contrast, plumes originating from the NW caldera site have much less gas with a pH shift of -0.09 units and no detectable H2S, TDFe up to 955 nM, TDMn up to 150 nM, and Fe/Mn values of 6.4, and have not changed their composition over the same three year interval indicating a more chronic hydrothermal system. Plume d3He results show helium is decoupled from more near-surface vent fluid sources although a shift in R/Ra values from 6.1 ± 0.5 in 1999 for the combined vent sites to 7.2 ± 0.1 in 2002 indicates a less radiogenic input of helium over three years, suggestive of a greater magmatic input to the system.

Jan 1, 2004

By Peter M. Herzig

In 1994 and 1998 the German research vessel R/V Sonne undertook detailed mapping and sampling of the largely uncharted offshore areas of the Tabar-Lihir-Tanga-Feni island chain in the New Ireland Basin of Papua New Guinea. The New Ireland Basin occupies a fore-arc position with respect to the formerly active Manus-Kilinailau arc-trench system and hosts a series of Pliocene to Recent alkaline volcanoes which are built on rifted Miocene sedimentary basement. Several of the volcanoes possess high-level porphyry stocks and active geothermal systems, including gold-depositing hot springs and the giant (40 million ounces) Ladolam gold deposit on the island of Lihir. On the southern flank of Lihir island, a group of three volcanic cones were discovered at water depths from 1.000-1.500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered volcanic rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts (ankaramites), porphyritic phlogopite basalts, and trachybasalts. Unusual gold-rich hydrothermal precipitates were recovered from the summit of the 600 m high Conical Seamount located only about 10 km south of Lihir Island. 1200 kg of sampled material systematically collected with a TV-guided grab from the top plateau (150 x 200 m, 1.050 m water depth) are intensely mineralized with pyrite, marcasite, minor sphalerite, chalcopyrite, galena, tennantite/tetrahedrite, and orpiment/realgar together with traces of anglesite, cerrusite, and amorphous silica in stockwork-like veins. Bulk samples of the vein mineralization consist mainly of clays, silica, and disseminated sulfides, and have an unusual high gold content ranging from 1.2-44.0 ppm Au. In some of these samples, grains of native gold (about 1 micron in diameter) were identified by SEM in pyrite and sphalerite. The gold-rich material also contains high concentrations of silver (up to 1000 ppm) and typical epithermal elements such as As (2.6 wt.%), Sb (0.2 wt.%), and Hg (34 ppm). Similar to epithermal deposits on land, which usually have only low base metal contents, the samples from Conical Seamount contain only minor amounts of Zn (max. 4.5 wt.%), Cu (2.0 wt.%), and Pb (2.0 wt.%). Many of the samples recovered from Conical Seamount are virtually identical to the gold ore at Lihir.

Jan 1, 1998

By J. R. Hein

East Diamante is a submarine volcano in the southern Mariana arc that is a complex caldera about 10 km x 5 km (elongated ENE-WSW), and breached on its northern and southwestern sectors. A large field of barite-sulfide mounds was discovered in June 2009 and revisited in July 2010 aboard the R.V. Natsushima using the Hyper-dolphin ROV. The mound field occurs on the NE flank of a cluster of resurgent domes inside the caldera. The mound field extends for more than 100 m long and is about 30 m wide, and is aligned along a NE-SW rift valley. A sample of dacite yielded a 40Ar/39Ar age of 20,000±400 years. Individual mounds are typically 1-3 m tall and 0.5-2 m wide, with lengths from about 3 to more than 5 m. The mounds are composed of barite-dominant layers interbedded with Zn-sulfide-rich barite layers. Rare inactive spires and chimneys cap some mounds. Fe and Mn oxides are currently forming small (<1 m diameter, ~0.5 m tall) subsidiary mounds on the top of some of the sulfate/sulfide mounds and drape the flanks of others. Both diffuse- and focused-flow fluids emanate from the subsidiary oxide mounds. Ages of the basal sulfate/sulfide mounds cluster around 4,000 years old based on 226Ba/Ba, whereas the oxides are less than 5 years old based on 228Th/228Ra. Most mound and chimney samples are dominated by barite and amorphous silica; sulfides occur in variable amounts that in decreasing order of abundance include sphalerite, galena, pyrite, and chalcopyrite. Anglesite, cerrusite, and a Pb phosphate occur as late-stage interstitial phases. Some mound samples have fragmental textures; layered clasts composed of chalcopyrite and pyrite may have been derived from collapsed chimneys. Despite the abundance of barite, samples contain high concentrations of Zn (to 23 Wt.%), Pb (to 13 wt.%), Ag (to 500 ppm), and Au (to 15 ppm). Copper is enriched in a few mounds samples, up to 3 wt.%, but is typically <1 wt.%. Other significant metal enrichments include Sb (to 1320 ppm), Cd (to 1180 ppm), and Hg (to 55 ppm).

Jan 1, 2011

By David A. Clague, James R. Hein, Robert W. Embley, Robert C. Vrijenhoek, Randolph A. Koski

We report preliminary results for a group of unique samples collected with MBARI’s ROV Tiburon on August 12, 2005. The samples were collected from the East Blanco Depression (EBD) diffuse-flow hydrothermal field, which was determined in a previous study to cover an area of at least 100 m by 80 m (Hein et al., 1999). The survey reported on here extends that field to more than 1500 m in an approximately N-S direction. The EBD, a pull-apart basin, occurs near the western end of the Blanco Fracture Zone (BFZ), which connects the Juan de Fuca and Gorda Ridge spreading centers (Fig. 1). The samples were collected from a waterdepth range of 3343-3380 m.

Aug 24, 2006

By Shinichi Takagawa

The deep sea hydrothermal deposits are one of the most prospecting resources, and various works to develop these mines are now underway. There are also various methods for the pre-site survey of the mines: acoustic survey, electro-magnetic survey, and others. However, as a precise method at the final survey, drilling/coring is indispensable to confirm the three-dimensional distribution and to grasp the dignity of the ores for the final decision of industrialization. This drilling/coring at the final survey is done at many points with distance of 15~25m between each point for on-land deposits. This means that 1km by 1km square area requires (1,000m/25m)2 ~ (1,000m/15m)2 = 1,600 ~ 4,500 holes. The drilling/coring depths will be around 30m or more for the hydrothermal deposits. This depth seems very shallow, but because the stratum is very brittle and is very difficult to core, the average core recovery ratio is around 50%, and 0% core recovery happens very often. Thus, the indispensable work of coring for grasping the dignity of ores is a very difficult work although the coring depth is shallow, and also the required number of holes is enormous. Conventional drilling/coring method on the ocean is to use drillship. However, the cost is very huge. Recently a new technique has come out which is to use remotely controlled drilling machine on seafloor. This machine seems to have a very good performance. However, it is reported that the available inclination of the seafloor where the machine sits on must be less than 15 degrees. The sea floor inclinations of active hydrothermal vents area are usually very steep and slopes of 45 degrees or more are prevailing and it seems very hard to carry out drilling/coring for the machine at these steep slopes, although it is impossible to mine the ore at these areas because the temperature is too high to work there. The inclination of the sea floor at the dead or paused hydrothermal vents area where ore recovery is possible may be not so steep, and the machine may work well. However, the required number of holes is still a very heavy burden. In order to solve these problems, the author proposes a new concept of drilling/coring system operated from a conventional research ship. This concept is still a desk plan, but the author wants to realize this system at any means.

Jan 1, 2011

By Michael Johnston

Nautilus Minerals is exploring for high-grade gold, silver, copper, and zinc-rich submarine massive sulphide deposits (SMS) within the territorial waters of the sovereign state of Papua New Guinea. Work to date has shown that these systems contain spectacularly high metal grades. To date a total of 88 surface sulphide grab samples have been collected from Nautilus’ Solwara 1 Prospect within EL 1196 in the Manus Basin, returning average grades of 15.5 g/t gold, 191g/t silver, 10.8% copper, and 4.7% Zn. Drilling in January/February 2006 confirmed the presence of this high grade system, with sulphide intersections up to 19m below the sea floor, with a best intersection of 11.6m at 9.1 g/t Au and 13.1% Cu.

By Stephan K. Schwank

In mid 1993, Bauer Spezialtiefbau GmbH, based in Germany got the order to develop a sampling tool capable of penetrating all different types of seabed sediments including cobbles and boulders and into bedrock. BHP and their partners Benguela Concessions Ltd., had been convinced by the Bauer Trench Cutter Technology and a large scale test in Germany that this system will be the right one to fulfill their expectations for sampling the diamond area off the coast of Namibia. The technique of the tool is based on Bauer&apos;s standard cutter technology, which is widely used for the installation of cut-off and diaphragm walls all around the world. The two counterrotating cutter wheels with 12.1 tom torque each cut an area of 3 x 1.2 m (up to 3 x 3 m are possible). The material mixed with seawater was then pumped to the separation plant on board the vessel Geomaster with a capacity of approximately 700 m3/h. Cutter wheels and mud pump were mounted on a special cutter frame and connected by wire ropes and hydraulic hoses to the vessel. An outer frame with four telescopic legs supported the cutter vertically on the uneven seabed and allowed a controlled penetration of the tool up to 6 m into the diamond bearing ground. The tool required a total power installed of approximately 800 kW. All hoses, the 6-inch mud hoses as well as the hydraulic hoses, were stored and compensated on drums on board suitable for a water depth of up to 200 m. Launch and recovery of the tool was effected through the moon pool of the vessel and the 25 m high, special designed drill tower. The 65? to sampling tool had been commissioned in early 1994 in Cape Town. After intensive testing the sampling programme of more than 4000 holes could be successfully completed by January 1995.

Jan 1, 1998

By Jung-Hoon Kang

Present study was stemmed from the survey associated with deep-sea mining in the KODOS area between Clarion Fracture Zone and Clipperton Fracture Zone located in the North Pacific Ocean. The study area, which is located in the southeastern part of North Pacific gyre, is oligotrophic waters with low nutrients and chl-a concentrations below 1µg/l (MOMAF, 1996). This area is also characterized by divergence at 8°N and convergence at 6°N, which moved northward or southward in the range of a few kilometers with seasonal and climate changes. If the waste materials related to deep-sea mining are intruded into the surface waters continuously, unexpected effects to water column ecosystem are anticipated negatively. In order to assess the impact on the planktonic ecosystem, natural variation need to be distinguished from anthropogenically induced variation in terms of the abundance and species composition of plankton. In this study, mesoscale variation of zooplankton community was reported in relation to the physical conditions in the northeastern Pacific during 1998 and 1999. Temperature and salinity were determined using a CTD from surface to 200m depth in July 3-20, 1998 and in June 22-July 1, 1999. Zooplankton samples were collected from two different depths (0-50m, 50-200m) by vertical towing using an opening-closing net (100cm diameter and 300 µm mesh size). The samplings were carried out at every one degree between 5° and 12°N (1998), between 5° and 11°N (1999) along the meridional lines of 131°30´ W. The net was lowered to the depth of interest from a stationary research vessel and towed upward to collect zooplankton at a speed of 25~30 m per minute. Zooplankton samples were transferred to 1-l sampling bottles and immediately fixed with neutralized formalin into the final concentration of 5%. Considering the characteristics of zooplankton such as diurnal vertical migration, all samplings were done during the nighttime. The volume filtered by the net was calculated from the readings of flow meter (Hydro-Bios Model 438-115). Zooplankton were identified to the genus level and enumerated under a microscope. The abundance of zooplankton at each station was expressed as the numbers/100 m3.

Jan 1, 2003

By Ivo Dreiseitl

The interaction between nodule harvester and eupelagic sediment on the seabed is definitely one of the key aspects of mining technology for polymetallic nodules which is to be studied in details. Physical properties of sediments play major role for evaluation of protection and preservation of marine environment while strength properties of sediments will come in useful for future mining operations. Cone penetration test (CPT) used for testing in situ is one of methods for investigation strength properties of sediments. The testing apparatus for CPT consists of an instrumented cone having a tip facing down and it is mounted on special underwater equipment (rus. UGI-1). UGI-1 can determine subsurface strength down to the depth interval 0 ? 1.10 m. Special IOM geotechnical cruise was accomplished in 1989 on board R/V Academic A. Karpinski within the extra test area of about 1000 km2. Thanks to UGI-1 the IOM database recorded unique strength sediment data (cone penetration resistance) from 279 seabed points of sounding at profiles 125.6 km long. Up to 35 strength data from depth interval 0-1.1m (every 3cm) were obtained from any particular testing point. As a result 279 strength charts could be plotted (two examples in Figure 1). The cone penetration resistance values can be correlated to shear strength parameters.

Jan 1, 2011

By Patrick J. C. Ryall

Remotely control led drills capable of being lowered to the sea-floor from ordinary research vessels have been developed over the past two decades. These drills are currently being used in geological survey programmes on the continental shelves (Canada, Japan, Norway, United Kingdom) and for studies of mid-ocean ridges. Generally the drills fall into two categories: 1) those which are powered from the surface and controlled by an operator, and 2) those which are battery powered and follow an automatic programme. Some drills have a television camera mounted on them sending a picture to the surface as an aid to site selection and geological interpretation. Typically the drills are capable of drilling a core 2.5 - 5 cm diameter up to 10 m long. While most of these drills are designed for <1000 m depth, some can drill in water depths of as much as 3500 m.

Jan 1, 1985

By Jon Machin

?ORE? is defined as ?mineral/s that can be mined at a profit?. So, what is ORE at 2,000 m water depth? Is it 5% Copper or 1.8% Nickel/Cobalt? One of the key factors that determine what is ORE, profitable or not, is the cost of mining and extraction. Therefore a determination of ORE requires a commercial and technical appreciation of both sea bed mining equipment and mining options. Perry Slingsby Systems (PSS) have built more remotely operated submarine work vehicles, including 900HP trenching machines, than any other company. With Nautilus Minerals, PSS have been studying a range of deep ocean mining solutions. This paper discusses the commercial and technical issues of various extraction techniques applicable to deep ocean mining from 1,500 m to 5,000 m water depth. Issues such as the rate of extraction, (i.e. tons per hour) is a key economic component and is often constrained by the design and horsepower of the miner. Likewise the design itself of the mining machine and cutting heads can determine the size of material produced which impacts on methods of lifting the ore to surface. Issues such as overburden, sea floor conditions, style of mineralization and physical properties of the ore, obviously affect the selection of appropriate mining machine configuration.

Jan 1, 2004

By V. K. Banakar

The occurrence of hydrogenous ferromanganese encrustations (Fe-Mn crusts) on the Cretaceous age Afanasiy-Nikitin Seamounts (ANS) in the eastern Equatorial Indian Ocean (EEIO) was first reported by Banakar et al. (1997, Marine Geology). The major element composition of the samples from the upper flank of the ANS (~1650 m water depth) indicated enrichment of Co up to 0.9 % (Parthiban and Banakar, 1999, Indian Mineralogist). Subsequently a project supported by the Department of Ocean Development to explore the ANS for Co-enriched Fe-Mn crusts was launched in 2002 by the National Institute of Oceanography. Sampling at regular depth intervals along two transects on the slopes of the northern elevated region of the ANS was carried out. The Fe-Mn oxide deposition is evident on almost all types of substrates viz., basalts, conglomerate limestone, fossil corals etc., and the thickness of the oxide layer varies from a patina to 7 cm. The Fe-Mn crust growth is evident only above a water depth of 3200 m, below which semi-lithified carbonate ooze is dominant. The ANS Fe-Mn crusts from all the water depths exhibit Mn/Fe < 1.5 suggesting pure hydrogenetic accumulation of metal-hydroxides. Bulk sample Ce-contents for a few selected depth-representative samples are remarkably high, up to 3700 ppm with an average of ~2500 ppm. The positive Ce-anomaly decreases from ~8 at 1600 m depth to ~1.6 at 3200 m depth, which is in contrast to the modern dissolved oxygen depth-profile in the region. This observation suggests that major time-period of the Fe-Mn crust accretion history is dominated by ambient waters with lower-oxygen at deeper depths than at the intermediate depths. This in turn probably suggests a major reorganization in the deep-intermediate hydrography of the region in the past.

Jan 1, 2005

By G. Cherkashov

A new hydrothermal field with massive sulfide deposits was discovered in 2004 at 16º 38.4?N, 46º 28.5?W on the Mid-Atlantic Ridge. Hydrothermal signals had already been recorded from bottom waters and sediments in this area during cruise 19 of R/V Professor Logatchev in 2000. This site was revisited during the 24th cruise of R/V Professor Logatchev in February 2004 when samples of massive sulfides were recovered and video records of the deposits made. The basalt hosted hydrothermal field is situated at a depth of 3700-3750 m, 600 m above the inner floor on the eastern slope of the rift valley. Structurally, the new field is located at the intersection of a deep along-axis marginal fault and a transverse sub-latitudinal dislocation. Six sulfide mounds as well as associated metalliferous sediments were mapped (sampled and/or recorded by video profiling) within the hydrothermal site. The largest ore body, 500 x 225 m, in the southern part of the field consists of small blocky talus and relics of sulfide chimneys partly covered by iron oxyhydroxides. The chimneys are 1-5 m high. The southern and western boundaries of the massive sulfide deposit have not yet been delineated. More than 1,100 kg of massive sulfides and stockwork mineralization were sampled at 7 sites by dredge and TV-grab. Everywhere, iron sulfides were the principal minerals present. Pyrite in association with lesser amounts of chalcopyrite occurs in both massive sulfides and stockwork mineralization. Of particular interest is the chalcopyrite-siliceous stockwork where silicified and chalcopyritized basalts are intruded by a network of chalcopyrite veinlets. These zones could be fairly thick and enriched in base metals. Sphalerite was very rare.

Jan 1, 2004

Clark volcano is a large volcanic center on the active arc front of the intraoceanic Kermadec arc. It is one of the two southern-most Kermadec arc volcanoes (the other being Whakatane volcano) that sits on oceanic crust before the transition to continental New Zealand, and is underlain by the 17-km-thick Hikurangi Plateau, which is presently subducting beneath the southern section of the Kermadec arc. Unusual K-rich basaltic lavas have been recovered from Clark (1.5 to 2.25 wt.% K2O), together with more typical basaltic-andesite, andesite and dacite rocks. The total volume of the Clark volcanic center is ~90 km3, calculated from the summit of the volcano down to the 2,500 m contour (which marks the inflection point of the volcano flanks with the surrounding seafloor) and comprises two separate edifices similar in size; the northern one having a volume of ~4.57 km3 and the southern one 4.43 km3. The volcano has a maximum relief of ~1,645 m from the 2,500 m contour to the summit of the shallower northern edifice shoaling to 855 m below sea level. The northern edifice is comprised of twin peaks each consisting of a constructional cone, with evidence of sector collapse having occurred between the cones. A more recent, smaller cone again has grown on the eastern flank between these summit cones. Massive, blocky lavas and coarse talus dominate the summits of the cones, with finer-grained volcaniclastic material and sediments a feature of the volcano flanks. The southern edifice is noticeably more dissected than the northern one, having a pronounced horst in the centre of the volcano bounded by 5-6 km-long faults. There is no obvious constructional cone atop the southern volcanic edifice.

Jan 1, 2011

By Mark D. Hannington

Results of the R/V Sonne Cruise (Edison) to the Tabar-Feni Arc from March 11 to April 5, 1994, a joint German-Canadian research cruise aboard the vessel R/V Sonne, undertook detailed mapping of the Tabar-Feni island chain, Papua New Guinea. The Tabar-Feni chain is host to several large porphyry stocks and epithermal gold deposits, including the giant Ladolam gold deposit on the island of Lihir (minimum 19 million oz. Au). The principal objective of the cruise was to map the seafloor in the vicinity of recently active alkaline volcanic islands in the Tabar-Feni chain and to characterize the tectonic setting of large high-level porphyry and epithermal gold deposits in the region. Additional work was carried out on shallow-water hot springs associated with mineralized geothermal systems on the volcanic islands. Complete sets of 1:50,000 scale (20-m contour) maps of the seafloor were produced for each of the four island groups (Feni, Tanga, Lihir, Tabar). The Lihir group was the most active and the most interesting. At least 4 (and probably 6 or 7), previously unknown volcanic cones were discovered within about 10 miles south of Lihir. The volcanoes are clearly very young and appear to have erupted along extensional faults produced by regional plate rotation. This recent volcanic activity appears to reflect recent forearc extension and represents the southward propagation of volcanic activity towards New Ireland. One volcanic cone at 1,490 m water depth is hydrothermally active, with very large areas of diffuse venting (100-200 m across), densely populated by beds of giant clams (probably calyptogena). Other vent-specific fauna are also present, including crabs, snails, sulfide worms, scale worms, limpettes, etc. The clam beds sit on a crust of hydrothermally baked and indurated, sulfidic, hyaloclastite-rich muds. The mineralization consists mainly of fine-grained disseminated pyrite and amorphous Fe-sulfides. A second, much larger cone at a depth of 1,070 m is capped by massive vesicular lavas which are intensely fractured and mineralized. Abundant sulfides and amorphous silica occur in stockwork-like veins which

Jan 1, 1994

By Kokichi Iizasa

Two major Kuroko-type deposits and minor sulfide deposits have been found in the middle Izu-Ogasawara (Bonin) Arc, Japan (Fig. 1). The Hakurei deposit, one of the major Kuroko-type deposits, was recently found in Bayonnaise knoll caldera in the nascent rift zone, which lies 20 km westward of the Sunrise deposit in Myojin knoll caldera on the Izu-Ogasawara volcanic front. The Hakurei deposit is a huge hydrothermal field measuring 500 m by 700 m in plan view. The Bayonnaise knoll caldera is mainly composed of dacite lavas and fragmental material on the caldera wall and rim, and its floor contains sediment composed of pumice, volcanic fragments, and hydrothermal clay. It is associated with a post-caldera dome and has a slightly ellipsoidal caldera rim that measures 3 km by 2.5 km, with about 200 m relief. The water depths of the caldera floor range from about 840 m to 920 m. The Kuroko-type deposit in the Bayonnaise knoll caldera occurs on the southeastern caldera floor where the caldera boundary faults intersect with a N-S-trending normal fault of the rift zone. In the deposit, many sulfide chimneys are generally less than 10 m high, and sulfide mounds are distributed around the caldera floor and on the sloping talus at the foot of the caldera wall. The deposit is buried in part by talus composed of pumice and volcanic fragments. Sulfide chimneys are still active, and inactive ones and their fragments are partly oxidized to reddish material. Chimney sulfides are mainly composed of sphalerite associated with chalcopyrite, galena, pyrite, and barite, and chemically enriched in Au up to 14 ppm and Ag up to 1400 ppm with major Zn, moderate Ba, and minor Pb, Hg, Cu, and Fe.

Jan 1, 2005

By Peter A. Rona

The Mid-Atlantic Ridge in the central North Atlantic and the Gorda Ridge within the U.S. Exclusive Economic Zone off northern California and southern Oregon are yielding new discoveries of seafloor hydrothermal mineralization. The TAG hydrothermal field in the rift valley of the Mid-Atlantic Ridge near 26 degree N, 45 degree W has been a site of international collaborative research since the discovery there of extensive manganese deposits associated with low temperature hydrothermal activity in 1973 as part of the TAG (Trans-Atlantic Geotraverse Project). The first high-temperature hydrothermal activity, massive sulfide deposits and vent biota discovered in the Atlantic were found at the TAG hydrothermal field in 1985. Collaborative dive series with DSV ALVIN in 1990 and in 1991 with the two Russian MIR submersibles in the TAG field have found and sampled large inactive sulfide mounds in addition to the previously known active sulfide mound. The active sulfide mound on the floor of the rift valley is about 250 m in diameter and 40 m high with a concentric zonation of mineral types and flow regimes decreasing in temperature from 365 degree C black smokers at the center to white smokers and diffuse flow toward the margins. The recent dive series in coordination deep-towed instrument surveys have delineated a zone extending about 5 km along the lower east wall of the rift valley of inactive sulfide mounds up to a kilometer in diameter. MIR Mound in this zone consists of a central sulfide zone about 400 m in diameter and 50 m high surrounded by a halo of low-temperature deposits to 200 m wide. Inactive sulfide chimneys contain the first primary, free gold grains found at a hydrothermal site on a mid-ocean ridge (P.A. Rona, Y.A. Bogdanov, E.G. Gurvich, N.A. Rimski-Korsakov, A.M. Sagalevitch and M. D. Hannington, 199 1 EOS, Transactions, American Geophysical Union, 72:470-471 and Journal of Geophysical Research, submitted).

Jan 1, 1992

By Andrew E. Grosz

The Atlantic Continental Shelf (ACS) of the United States includes about 391,000 km2 extending from the shoreline to the 200-m isobath. It varies in width from a fraction of a kilometer (offshore of southern Florida) to about 150 km (offshore of Cape Cod, MA). The contained volume, of sand and gravel is estimated to be on the order of 3-7 x 1.011 m3. Concentrations of potentially commercially important heavy minerals (HM) exist locally, particularly in high-energy depositional environments (for example in channels, tidal deltas, ridge and swale areas, and submerged former shoreline complexes). Recently completed and ongoing studies of HM assemblages in vibracore samples from the south shore of Long Island Sound, NY, offshore of Ocean City, NJ, offshore of Cape May, NJ, offshore of the mouth of Chesapeake Bay, VA, offshore of Myrtle Beach, SC (grab samples), and the ACS offshore of Florida provide the information base for this presentation (Table 1). The surficial sediments of the ACS contain local concentrations of HM that compare favorably to those in currently mined onshore deposits as shown

Jan 1, 1988