Search Documents

By K. Esmaieli

The Synthetic Rock Mass (SRM) approach has the potential to capture the mechanical behavior of large rock samples. In order for the method to be used with confidence it is necessary to gain a good understanding of the factors that influences its analysis. This paper reports on a series of numerical experiments, based on field data from a large underground mine, to investigate the influence of intact rock mass strength of a constructed (SRM). A jointed rock mass defined by three fracture sets was simulated by a Discrete Fracture Network (DFN) model. The generated fracture network was subsequently embedded into six different intact rock samples, simulated by a bonded particle model in PFC3D, generating six SRM samples. Each intact rock sample was 7 m × 7 m × 14 m and assigned different mechanical properties. The first intact rock sample was assigned a uniaxial compressive strength of 205 MPa and an elastic modulus of 104 GPa with the UCS and elastic modulus values of the other samples downgraded by 10% until the weakest sample had a UCS value of 121 MPa and an elastic modulus value of 61 GPa. All SRM samples were loaded under uniaxial compression to obtain the complete stress strain curve. It was observed that the compressive strength of the rock mass samples decreased by 10% following the same trend as the rock material strength. However, the elastic modulus of the rock mass samples decreased non-linearly with reduction of the elastic modulus of the rock material. The Poisson's ratio of rock mass samples does not change with decrease of rock material properties. For the post-peak behaviour the results show that both the brittleness index and the residual strength of rock mass samples decreased as the rock material properties degrades.

Aug 1, 2013

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By R. Pakalnis, D. Tenney, B. Lang

"This paper describes three case histories whereby numerical methods were employed as a tool in the identification of potential instability. Simple two dimensional (PCBEM) and pseudo three-dimensional (BESOL, MINTAB) codes were employed to identify zones of induced stress which were subsequently related to extensometer, stress meter and observational data as the stope was excavated. The following case histories will be discussed. MacLellan Mine - sill pillar stability; Ruttan Mine-Hanging Wall Stability; and Detour Lake Mine-narrow vein mining.The MacLellan case history showed how modelling and instrumentation enabled mining to be conducted safely and under controlled conditions. MINTAB and PCBEM were employed to predict sill pillar failure. The sill pillar failure was associated, with an unloading of stress which was recorded by instrumentation (stress meter) and a decrease in the over-all rock mass strength. The yielded pillar, however, maintained its over-all configuration enabling access through the pillar.The Ruttan case history is an example of hangingwall and footwall design whereby the existence of adverse structure coupled with a zone of relaxation results in dilution. BESOL and PCBEM were employed to model a test stope and to verify the observations and measurements through instrumentation . Empirical methods of dilution estimates are employed to determine the level of walls lough with respect to the rock mass rating, stope dimensions and rate of excavation.The Detour Lake case history in an example of open stoping a narrow steeply dipping deposit. Stope dimensions are 135m in strike length, 47 m in vertical height with an average width (F/W to H/W) of3.6 m. Stress meters coupled with visual observations are related to modelled estimates of stress and dilution."

Jan 1, 1991

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement .Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement.Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By Sunil S. Gandhi

"The Mountain Lake deposit is a tabular sandstone-type uranium deposit, hosted by the basal unit of Middle Proterozoic Dismal Lakes Group. Uranium occurs mainly as sooty pitchblende disseminated in stratiform lenses within gently dipping quartzose sandstone. It is associated with copper sulphides, pyrite, hematite, and traces of nickel and cobalt arsenides and of silver.Exploration HistoryUranium showings on the PEC claim group were discovered during 1969 by an airborne radiometric survey carried out over the Dismal Lakes-Great Bear Lake area by Aquitaine of Canada Limited (Bizard and Salat, 1969). Some drilling was done in the vicinity of the showings in 1975 by the company under a joint venture with Eldorado Nuclear Limited but the results were not encouraging (Hassard and Woollett, 1975). During 1972, Trigg, Woollett and Associates Limited conducting surveys for Imperial Oil Limited, discovered numerous high-grade radioactive boulders scattered over a distance of several kilometres north and west of the showings, and the area north of the PEC claims was staked as the YUK claims (Ahuja, 1974). A systematic study of the boulder distribution and Pleistocene geology suggested a source additional to the showings. More intensive exploration followed, and in 1976 drilling just north of the PEC claim group boundary intersected the main deposit at a depth of 75 m to 150 m, beneath overburden up to 60 m thick. Part of the deposit extends into the PEC claim group which is under exploration by the Aquitaine-Cominco Joint Venture.The following brief description is based on the presentations in 1978 by F. Hassard of Trigg, Woollett and Associates Limited at the Geoscience Forum in Yellowknife, and by S.S. Gandhi of the Geological Survey of Canada at the Mineralogical Association of Canada Uranium Short Course in Toronto."

Jan 1, 1986

By J. P. Aiello

"INTRODUCTIONWhile this paper deals specifically with potential coal use at the Cold Lake Project of Esso Resources Canada Limited, a majority of the technical aspects of coal conversion could apply to any oil field and industrial boilers or stearn generators. In 1962, Imperial Oil Limited's production arm (the forerunner of Esso Resources), began examining methods of extracting bitumen from a 50 m thick layer of oil sand buried 450 m below the surface in the Cold Lake area. Almost two decades of research followed to develop an in situ oil sands recovery technology that made commercial production feasible.A $13 billion mega project that would have produced 22 000 m3/d (141 000 barrels/day) of synthetic crude oil (160 000 bpd of bitumen) was shelved in 1981, and ultimately replaced by a phased development strategy, involving smaller production units, to bring blended bitumen production on stream as markets and prices permit.The first two phases came into production in 1985. There are currently a total of six phases in production with four more in the construction stage. Each phase has 130to 140production wells (initially) and a central plant with water treatment, crude treatment and stearn generating facilities capable of producing 150 m3/d (9500 bpd of raw bitumen). The stearn generation section for each phase consists of three 180millionBtulhour oil fieldsteam generators.In its natural state, the bitumen is too thick to be recovered using conventional oil recovery techniques. At the Cold Lake Project, bitumen is recovered by a method called cyclic stearn stimulation. Water is pumped to the central plant where it is treated and heated to produce high pressure, high temperature steam. During the steam cycle, this steam is transported in insulated pipelines to the wells for injection into the oil sand formation. This cycle lasts from 30 to 50 days, heating the formation and causing the bitumen to flow. Following an initial flowback period, a surface based artificial lift system pumps the heated liquid bitumen, mixed with water and gas, out of the well and back to the central plant. The water and gas are separated from the bitumen, with the gas being used to provide some of the fuel for the stearn generators and the water being treated and recycled. Approximately 5% of the water cannot be recycled and is disposed of by injection into deep formations . The bitumen is blended with a diluent and shipped by pipeline to market."

Jan 1, 1989

By Gabriel Zarate

"Los Bronces had two ROM dump leach operations designated Leach I and Leach II. Leach I was commissioned in 1998 and stopped in 2014 due to the mine requirements. Leach II plant, commissioned in early 2002, was built to treat around 700 million tons of marginal ROM ore averaging 0.45 % total copper. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides.The original electrowinning plant design capacity for copper production was nominal 19,500 tonnes per year at a current density of 276 A/m2 and a current efficiency of 92%. Presently, Los Bronces San Francisco plant typically operates at current densities between 390 and 440 A/m2, much higher than the average in the industry, with current efficiencies around 93% and a maximum copper cathodes production of 37,200 tonnes per year.In order to accomplish these achievements, a number of modifications in the process conditions, in the cell hardware and in the operational procedures have been implemented. In the first case, the specific flowrate, copper concentration and temperature of the electrolyte were modified to accommodate the operational requirements facilitating the increased current density. Associated with the cell hardware, a six cells expansion was added, upgraded equipotential inner cell busbars were installed and the cross section of the cathode hanger bars was enlarged for increased current carrying capacity. Documented operational procedures like short circuit detection and cathode weight control were improved.The modifications implemented and the results obtained are discussed in this paper.INTRODUCTIONLos Bronces Division of Anglo American Chile is located up in the Andes Mountains, northeast of Santiago. It had two cathode plants, Los Bronces at an altitude of 3500 meters above sea level (m.a.s.l.) commissioned in 1998 and closed in 2014 and San Francisco at an altitude of 2800 m.a.s.l. and in operation since 2002.The process is leaching run off mine (ROM) low grade copper sulphide ore in dumps. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides. The average grade is 0.45% total copper (Cut).At Los Bronces dump, Leach I plant, the pregnant leach solution (PLS) was collected and stored in an underground reservoir. From there, it was fed to a solvent extraction plant with a series-parallel configuration in two extraction stages and one stripping stage. The electrolyte produced was fed to the electrowinning plant having 30 cells and 60 cathodes per cell. Maximum capacity of this plant was 12,000 tonnes per year (tpy)."

Jan 1, 2016

By Michael Boyle, John Zeni

"The Blind shaft boring method is a mechanised process of excavating large diameter vertical shafts downward from the surface. It is a rotary drilling technique eliminating any requirement for personnel to enter the shaft or access underground workings during drilling and lining phases. Excavated material is delivered to surface carried by a flow of circulating fluid through the centre of drill rods. The drill assembly is suspended from a large A-frame rig and powerful winch at ground level providing vertical thrust to a hard rock cutter head. INTRODUCTION The Southern Coalfields Ventilation Shaft was constructed at a mine, 45 km north-west of Wollongong. The 5 m finished diameter (6.2 m drilled) shaft reaches a final drilled depth of 517 m, the deepest, fully lined blind bored vent shaft to date in Australia. Operated by a mining company in the Southern Coalfields, the expanding mine required a new ventilation shaft and associated surface infrastructure to service future operations. An assessment of future ventilation requirements for the coal seam operations identified a need to improve the capacity and reliability of the existing underground ventilation system in order to ensure a safe and efficient underground working environment. Installation of the new upcast ventilation shaft was determined to be the most cost effective and reliable solution to provide adequate ventilation for underground operations. The completed shaft is smooth and fully lined with steel/concrete composite liners that are hydrostatically sealed. The shaft lining is designed to meet the mine ventilation requirements for a service life of 20 years. The shaft intersects the top of the working section of the coal seam at approximately 513 m of depth. This includes the shaft collar depth and shaft bottom profiled intake section.PROJECT METHODOLOGY AND INDUSTRY BEST PRACTICE The shaft was drilled using the blind bore method, an innovative construction technique and an alternative to the traditional methods of sinking deep and large diameter shafts, such as raise boring and conventional drill and blast shaft sinking. The blind bore method allows the shaft to be drilled from the surface down without anyone having to enter the shaft or the mine during the construction process. This is by far the safest method of shaft construction and is especially suitable for difficult ground conditions where there may be unstable or water-charged strata. As this method involves drilling from the surface downward, shafts can be completed ahead of the underground mine development. Thus, allowing underground operations to focus on development and production without the conflicts of managing ventilation priority for underground contractors and mucking out spoil from excavation workings."

Jan 1, 2019

By J A. Gilliand

Mineralogical cross sections of orebodies on the 300-,600- and 900-foot levels of the Coronation mine have been interpreted in terms of centers of mineralization. The maximum concentration of chalcopyrite occurs closest to these centers, with pyrite and pyrrhotite concentrated some distance away. The magnetite concentrations are farthest removed from the centers. A hydrous halide fluid model is established. Attempts to explain the observed mineralogy by the action of temperature gradients on the fluid model were unsuccessful. Likewise, the action of diffusion alone on the fluid model cannot explain the observed mineral distribution. The concept of attenuation is introduced-i.e., the rate of diffusion of a particle species is related to the product r2 I/ M, the attenuation coefficient, where r is the particle radius and M its molecular weight. Attenuation, acting on the fluid model alone, will not produce the observed mineral distribution, but, when considered together with the action of temperature gradients, the observed mineralogy can be well explained by the combined effects of these two processes on the assumed fluid model.

Jan 1, 1965

By T S. Cochrane

This paper is based on observations made during a recent visit by the writer to three of the dust research laboratories .in West Germany, each .of which is mainly concerned with studymg the composition and character of the respirable dust produced in mines or at industrial sites. The three institutes are discussed as regards their orgamzat10n and duties, their methods of dust sampling and analysis, and recent trends in research and development. An extensive bibliography completes the paper. Introduction A RECENT trip to Europe to attend international conferences m Austria and m Belgium gave the writer the opportunity to visit a number of research laboratories and mines in Western Europe. The visits to the dust research laboratories in West Germany are the basis of this report. In Germany, cooperative associations formed prior to and since the turn of the 20th Century to promote the safety and welfare of their workers have recognized the effects of airborne dust on the general health of the labour force.

Jan 1, 1964

By G. F. Trainor

The complex ore body at CNRL?s Horizon mine presents some unique challenges in managing ore and waste delivery. With 25m x 25m ore blocks shovels often take bucket loads from multiple blocks to fill one truck load. With CNRL monitoring 22 different qualities per material a precise calculation of the blended quality of ore on the back of each individual truck is essential to meet the daily blend requirements at the plant. Additionally, one of these qualities must be closely monitored and controlled at a singular level as delivery of certain grade and quantities can cause serious disruptions at the plant. The waste material also requires special handling and delivery for its use in dyke construction for tailings impoundment. Shale materials used in the construction contain high levels of saline that must be contained to prevent seepage into ground water. This paper will discuss how the use of Wenco?s survey-grade GNSS system on shovels, its dispatching algorithm, and fleet management applications give CNRL the ability and confidence to control and report on these three issues.

May 1, 2013

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006

By J. Severin

Surface mining operations are increasingly involving the design and development of deeper and larger open pits, often with plans to transition into underground mass mining operations. Experiences at the Palabora Mine in South Africa demonstrate the complex interactions between underground workings and the steep slopes above that may lead to slope movements that potentially pose safety and economic concerns. To properly assess the rock mass response to these interactions for planning of future developments, understanding the controlling influence of geological and geomechanical structures is crucial. Preliminary results are presented from a detailed review of historical slope monitoring data from the Palabora Mine, before and after the initiation of block caving 400-m beneath a 800-m deep pit. This paper demonstrates that a detailed analysis of geology and monitoring data can be used to better understand the kinematic controls of complex rock slope displacements and interactions between open pits and underground mines. This investigative treatment of the monitoring data is important in understanding the failure mechanisms prior to undertaking sophisticated 3-D numerical models.

May 1, 2009

By J. Spross

"The Key Lake mill has operated since the fall of 1983. The ore from both Key Lake open pits will be depleted by 1997. It is planned to use this mill, located about 60 km southwest of McArthur, to process the McArthur River ore.While the geological data collected so far on the McArthur deposit are encouraging, more information of the deposit is needed before any detailed mine planning can begin.The surface drilling program identified the orebody and provided information on the geomechanical and hydrological properties of the overlying sandstone. It was proposed to conduct an underground exploration program to further delineate the orebody. This was air proved following a public hearing and review process. This program involves the sinking of a 630 metre deep shaft and the driving of one or two drifts along a portion of the orebody. From these drifts, exploration drilling every 10 m to 15 m through the orebody will provide the information required for the preparation of a feasibility study and an Environmental Impact Statement (EIS)."

Jan 1, 1994

By N. W. D. Davis

"As I have recently carried out some further research on the Navan lead-zinc deposit data while working in Michel David's research team, I should like to add a few comments on the paper- ""Universal Kriging for Ore-Reserve Estimation- Conceptual Background and Application to the Navan Deposit"", by M. Dagbert and M. David (CIM Bulletin, pp. 80-92, February 1976). The first comment is that since this research has been carried out, important new theoretical advances have been made which make for an easier application of geostatistics to the non-stationary case (see Matheron0l). This is the theory of intrinsic random functions of order k. With the aid of this theory, it has been possible to write computer programs which can carry out automatically universal kriging, although so far such applications have been largely confined to automatic contouring and not to mining problems. However, if approached with care there is no reason why these methods should not be applied to mining problems and, in this case, an automatic study has been done on this data."

Jan 1, 1976

By Robert A. Brown

"The O'Brien mine is in the west-central part of Cadillac township along the Cadillac 'break', which extends for 7,500 feet from west to east across the property.The ground was staked in 1924 by A. Dumont and W. Hermeston, prospecting for M. J. O'Brien, Limited. The first vein discovered is that now known as No. 1. The No. 4 vein was later exposed on the surface; the other veins known to be present were revealed by underground work and diamond drilling carried out both from the surface and underground.The mine is developed from three vertical shafts: No .. 2 extending from the surface to 2,000 feet; No. 3 from the surface to 1,500 feet; and No. 4 from 2,000 to 3,000 feet. There is on the property a mill of about 200 tons a day capacity, the usual shops, and a townsite housing about forty-five families. Gold production to the end of September, 1944, amounted to 295,824 fine oz. from ore having an average grade of 0.505 oz. a ton. In addition, the mill recovered 3,237 tons of arsenic trioxide having a purity of 83 per cent As2O3.GENERAL GEOLOGYThe four main groups of rocks of the Cadillac area- the Cadillac, Blake River, Kewagama or Pontiac, and Malartic- are found within the boundaries of the property. However, as these rocks have been fully described in · various government reports (1,2,3,4,5,6) and all the known orebodies occur within one group- the Blake River-a detailed description of the geology will be dispensed with here. The known ore deposits lie south of the Cadillac 'break' in a group of rocks that includes 'greenstones', greywackes, conglomerate, porphyries, and a rock of gabbroic composition that may be intrusive. Both flows and tuffs can be recognized in the 'greenstones'. The two bands of porphyry that trend easterly across most of the property have been considered by some observers to be dyke rocks and by others to be flows. Certain evidence points to their being dykes that were intruded as sills considerably prior to the emplacement of the gold-bearing veins, but the possibility of flow origin cannot be fully rejected. North of the talc-chlorite-carbonate schist zone forming the 'break' the rocks are conglomerate and greywacke with iron formation, in which there are no known veins of ore grade. Within the schist zone are minor acid and basic intrusives. The general trend of both bedding and schistosity is a few degrees south of east. The dip is generally vertica1 or steep to the south."

Jan 1, 1954

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By G. R. Morin, A. R. Leggett

"In 2010, closure of the Kidd metallurgical plants along with structural changes to the historical ratios of payable metals led to a review of the operating targets at the Kidd concentrator. Previous operating data indicated that there was potential for significant revenue improvements by lowering the copper concentrate grade. An extended plant trial was carried out in 2011 to quantify the revenue impact of lowering the copper concentrate grade from 27% to 25% Cu, as well as identifying the lower practical grade limit. Analysis of plant trial results indicated that the process change increased net concentrate revenue by $2 M to $3 M per year at current metal prices. Increased revenue was primarily associated with higher silver recovery to the copper concentrate while the marginally improved copper recovery was essentially offset by increased zinc losses and concentrate treatment and freight charges.Details of the plant test work results are discussed in this paper along with the financial analysis of the revenue improvements. Key areas covered are major revenue components of the concentrate contracts, validation of revenue improvements through plant testing and sensitivity of the improvements to market and plant variables.INTRODUCTIONThe Xstrata Copper Kidd concentrator commenced operations in 1966 treating ore from the nearby Kidd volcanogenic massive sulphide deposit in Timmins, Ontario (Thompson, Amsden, & Chapman, 1978). Over the years, up to four separate grinding-flotation divisions were in operation with throughput rates peaking at 4.5 million tonnes per year of ore in the mid 1980’s (Kelebek & Francis, 1998). As the mine production decreased and grinding throughput increased operations were gradually cut back and since 1998 two grinding-flotation divisions have been in operation treating Kidd mine ore. One of the idled divisions has been intermittently used for custom milling operations, most recently the Ni/Cu Montcalm deposit, which was milled from 2004 to 2009. Current budget throughput rates, limited by mine production, are 2.4 million tonnes per year of ore grading 1.7% Cu, 4.3% Zn and 55 g/mt Ag. Concentrate production rates are 150,000 tonnes per year of copper concentrate and 155,000 tonnes per year of zinc concentrate. The Kidd mine is the deepest base metal mine in the world with mining operations down to 9600 ft.In 2010 the copper and zinc plants at the Kidd metallurgical site, which previously treated the concentrate production from the Kidd concentrator, ceased operation due to a variety of economic and market factors. Following the metallurgical plant closures the Kidd concentrator products were shipped off site for treatment. The majority of the copper concentrate is now processed at the Xstrata Copper Horne smelter in Rouyn-Noranda, Quebec with the majority of the zinc concentrate processed at Canadian Electrolytic Zinc Ltd. in Valleyfield, Quebec."

Jan 1, 2013

By Paolo Toscano, Dave Hall

"This paper discusses the project history, process design and layout of the Rainy River Gold Project mill. The circuit consists of a 55 x 83 primary crusher, 15 MW SAG mill and 15 MW ball mill. Both mills are twin pinion with LSS and VFD drives. A pebble crusher is located in the process plant with bypass and stockpile options. Gravity concentration followed by 30 hours of leach residence, carousel CIP, carbon recovery, cyanide destruction and tails disposal in a 1,428 hectare tailings management area (TMA).The Rainy River Gold Project is located approximately 65 km northwest of Fort Frances in north western Ontario. The project is scheduled to be commissioned and reach commercial production in mid-2017. Expected cost is $US877M and is comprised of an open pit mine, process plant, tailings management area and supporting infrastructure. The process plant is designed to produce gold/silver Dore’ bars.The project has been developed on the following timeline:• 1967 – First exploration• 1994 – 17 zone discovered• 2004 – 433 Zone discovered• 2005 – Rainy River Resources Ltd. purchases property • 2006 - ODM zone discovered• 2007 - Cap Zone discovered• 2008 - First NI-43-101 Resource completed• 2012 - PEA completed & Intrepid Zone discovered• 2013 - New Gold acquires Rainy River Resources• 2014 - Updated feasibility study completed & Environmental Assessment report submitted• 2015 - Detailed Engineering >95% complete, EA approved and construction commencesThe property is accessed by provincial highway 600 and is within 17 km of 230 kV power line and railway sidings. Key project criteria are summarized as follows:"

Jan 1, 2016