Search Documents

During conventional eddy current separation, a repulsive force is applied to metallic particles by placing them in a rapidly changing magnetic field generated by a spinning magnetic rotor carrying an arrangement of alternate magnetic poles. This method works effectively for larger non-ferrous metallic objects, such as aluminium cans, but as the metallic particles become smaller, the bulk repulsive force on the particles is increasingly replaced by a rotational torque. Therefore, for small metallic particles it makes sense to use particle rotation, rather than particle repulsion, to effect a separation. Eddy current separators using particle rotation are similar in construction to present separators, but are designed to produce a rotating field of essentially constant angular velocity and field strength. Practical and economic particle rotation eddy current separations are possible down to particle sizes of about 200 ¦m, but separations, at probably uneconomic rates, can be carried out on particles as small as 50 ¦m.

Jan 1, 2000

By S Leary

Diamond drilling since early 2006 has identified an epithermal gold-silver (Au-Ag) deposit beneath 140 m to >400 m of cover. The Fruta del Norte discovery had an inferred resource estimate of 58.9 Mt grading 7.2 g/t Au in October 2007. The mineralisation is hosted by Mid-Late Jurassic andesite and andesite porphyry in a regional fault zone beneath mainly post-mineral but in part syn-mineral Late Jurassic cover. The intermediate sulfidation-style deposit formed before and in part during deposition of epiclastic cover in the fault related pull apart basin. In addition to its size and obvious economic importance, the widespread occurrences of visible gold and exquisitely preserved epithermal textures will make Fruta del Norte an important learning tool for explorationists seeking epithermal mineralisation in theAndes and elsewhere. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

This data is intended to provide a quantative cost comparison of one 40 800 kg. pull down rotary blast hole drill versus two smalter drills in the 18 100 kg. pull down class. While this cost analysis is affected by blast design, this paper is not intended to be a treatise on blasting theory and therefore places more emphasis on costs than on blast design. All costs, prices and production rates in this paper are estimates and should be used for comparison purposes only. The drills are sized in order to maintain a production rate sufficient to stay ahead of a dragline that is excavating in an average overburden (sandstone and shale). The large drill will use 270mm bit and penetrate at a rate of 0.012 m/s (scheduled basis). The small drill will use 170mm bit and penetrate at a rate of 0.010 m/s (scheduled basis).

Jan 1, 1986

The area around Big Bell was actively explored and sporadically mined for gold from 1904 onwards. The lease was named Big Bell in 1913. The property became established as a major mining centre with the development of the Big Bell underground mine in 1936. Mining operations commenced in late 1937 and ceased in January 1955, after milling 5.56 million tonnes of ore and producing nearly 21 tonnes of gold. In 1969 Australian Consolidated Minerals Ltd (A.C.M.) acquired the deposit then explored it alone and in joint venture until the current joint venture agreement with a subsidiary of Placer Pacific Limited (PPL) was negotiated in 1984. Following exploration and evaluation of near surface mineralisation, and a reassessment of the remnant pillars underground, the concept of a large open pit in conjunction with an underground mine evolved. The feasibility study was completed in October 1987, and the decision to go ahead was formally announced on 2nd December 1987. Placer Dome Technical Services Ltd were contracted to be the Project Managers, commencing construction on site early in January 1988 and handing the plant over to the operators 13 months later. The capital cost of the project at handover was estimated to be $133 million. The operating team commenced pre-production stripping of the open pit on 1st May 1988. By 31st January 1989 almost 16.0 million tonnes had been stripped and 350,000 tonnes of ore stockpiled.

Jan 1, 1989

A description is given of preliminary work done to identify the problems inherent in electrochemical oxidation of metal sulphides, and particularly in the use of powder compacts as anodes in electrolysis. Lead flotation concentrate pressed into a compact can serve as an anode for direct electrowinning of lead according to the reaction PbS -7 Pb2+ +So +2e. No pYrometallurgical step is required, and sulphur is recovered in elemental form.In the experimental work, electrical conductivity of the compacts was achieved by addition of 5·5 per cent of graphite. After compaction at 10-20 tons/sq. in. the anodes were strong and remained intact throughout the electro-oxidation period. Perchlorate electrolyte was used, but fluosilicate electrolyte is also applicable. A sheet of pure lead formed the starting cathode.As anode potential increased above 1·0 V (v. SHE) PbS04 was formed in increasing amount. At 0·90 V, Pb2+ extraction efficiency was 85 per cent. Anode potential was kept low by electrolysing at 60°C and 15 mA/sq. cm., and by improving the porosity of the compact. Other metal sulphides (Zn, Fe, Cu) in the flotation concentrate also oxidize and release metal ions to the electrolyte, which would need to be purified prior to deposition of lead.Power requirement in a laboratory cell was about 0·24 kWh per lb of lead extracted.

Jan 1, 1972

By G J. Corbett, T M. Leach

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as zone C, is a mine recoverable 432,000 t at 18.1 g/t Au & 46 g/t Ag. Mining will be by a combination of open pit and underground at a rate of 100,000 t per annum. Processing will be by SAG mill, gravity circuit and CIL plant. A diatreme breccia, localised at an intersection of structures and a relationship of gold to base metal sulphides, are indicative of a strong porphyry association. Typical epithermal features such as crustiform banded quartz and quartz pseudomorphing platy calcite are also present and locally contain lesser gold mineralisation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100 m strike. A fluid flow model suggests that mineralizing fluids were sourced from a diatreme margin and migrated laterally along dilatant structures. Bonanza gold grades are interpreted to be derived through fluid quenching in the flexure between a hanging wall split, which hosts much of the Tolukuma Hill resource, and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting.

Jan 1, 1995

By G W. Wilson, M Aubertin

A desulfurised tailings cover was installed at the Detour Lake Mine in Ontario, Canada, to reduce oxygen penetration into the underlying sulfidic tailings. The cover ranges from one to 1.5 m in thickness and was intended to maintain high water saturation to reduce oxygen diffusion and consume oxygen by oxidation of the residual sulfide minerals. The tailings impoundment was instrumented to measure climatic parameters, water levels and water content profiles within the tailings and single-layer cover. One year of monitoring data was collected. Additional tailings samples were obtained for geotechnical and geochemical characterisation. The average grain size of the cover material was found to be coarser than the underlying tailings. Monitoring also indicated that air entry values of the cover material were lower than the tailings. Numerical modelling was conducted on the cover to predict water content profiles under varying climate conditions together with the depth of oxygen penetration and diffusive oxygen fluxes. Estimates of the diffusion coefficient and kinetic oxidation rates from field data compared well with values obtained by laboratory measurements. Numerical simulations indicate water saturations of less than 85 per cent can be expected under varying climate conditions. Predicted oxygen flux rates through the desulfurised cover over tailings with high acid potential indicate low flux rates reaching these tailings due to either consumption of oxygen by residual sulfur within the cover or saturation of the underlying tailings.

Jan 1, 2003

By T A. Short, P L. Brown

Kestrel Mine co-disposes around 1.5 Mt of fine (2SO4/t and to date around 9 Mt has been deposited. The mine plans to co-dispose of approximately 39 Mt of material, creating a dump with a maximum height of 35 m and a disturbance footprint of 260 ha. Benign materials suitable for rehabilitation are severely limited and no successful rehabilitation strategy has yet been demonstrated. A rigorous measurement and modelling program is resolving outstanding issues associated with acid rock drainage (ARD). The objective of the program is to develop and validate a strategy for dump rehabilitation that will control ARD and allow for mine closure. The strategy includes using a soil cover to reduce water flux into the dump to control the overall oxidation rate and to control effluent release. Monitoring of the oxygen distribution and water flux in the uncovered material commenced in February 2001 and monitoring in waste under a trial cover commenced in February 2002. Carbonaceous and sulfidic oxidation rates have been measured. Initial modelling indicates that the carbonaceous material has the general effect of slowing the rate of pyrite oxidation, lowering the maximum sulfate production rate and extending the time to oxidise all the sulfides. The combined approach of measurement and modelling provides a sound basis for assessing the performance of the trial cover and predicting the long-term quality and quantity of effluent at the base of the rehabilitated waste dump.

Jan 1, 2003

By P J Savory

Ranger is a uranium mining operation located within one of the most environmentally sensitive regions of Australia. Geology has played an important role in mine planning, operations and rehabilitation since discovery of the deposits 25 years ago. The Ranger orebodies have a reserve total of 166 300 tonnes of U308 including 90 400 tonnes of U308 at North Ranger. At current milling rates these reserves give a mine life greater than 40 years. The uranium is hosted in Lower Proterozoic rocks of the Cahill I ormation and is associated with strong chlorite alteration. In pit grade control involves the use of calibrated probes and a radiometric truck discriminator allowing fast, accurate grade determination of material. Ore is defined at a cut-off grade of 0.2 per cent U308. Mineralised material is defined by the Uranium Mining (Environmental Control) Act 1979 (UMEC Act) at a grade of 0.02 per cent U30s. Natural water levels in the #1 Pit area vary as much as 7.5 metres between wet and dry seasons. Ground water inflow into the pit during the dry season is 600 m3/day. No significant slope failures have occurred in the pit. The environmental impact of mining operations is constantly monitored. Rehabilitation of non-mineralised stockpiles is ongoing. This paper discusses the interaction between geology, hydrogeology, rock mechanics and grade control with the present mining operation.

Jan 1, 1994

By W N. Qin, B Zhang, W Z. Huang, X S Mo

Mengzi Mining and Metallurgy Co, Ltd (MMMC) polymetallic ore contains recoverable amounts of tin, lead, zinc, pyrite and other valuable minerals. With the change in orebody, the run-of-mine (ROM) ore changed from lead zinc rich ore to tin rich ore, where the current ROM ore contains 0.45–1.25 per cent tin, 20–25 per cent sulfur, and 0.20–0.35 per cent copper. The previous processing flow sheet was designed to recover lead zinc rich ore and it is clearly not suitable for recovery of the current tin rich ore, where the tin was already overground and tin recovery was only 50.19 per cent. The Mengzi Mining Company has recently modified the concentrator circuit by incorporating rod mill and high efficient Derrick fine screen. As a result of the improved classification efficiency, the overgrinding of the tin ore was minimised and the recovery of tin was improved by 20.71 per cent, ie from 50.19–70.90 per cent. An additional $10 M revenue per annum can be achieved as a result of the modification.CITATION:Qin, W N, Huang, W Z, Mo, X S, Zhang, B and Wheeler, J, 2014. Application of high efficient fine screen to improve the recovery of tin concentrate, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 487–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By B Roach, P M. Ashley, B Hooper

Mineral occurrences of the Hillgrove Au-Sb-W district are hosted in late Palaeozoic polydeformed, hornfelsed metasediments and Permo-Carboniferous granitoids of the NewEngland Orogen. In excess of 204 individual occurrences have been identified to date with the mineralisation developed as strike extensive (>20 km of known veining) and potentially depth extensive steeply dipping fissures. These are contained within an elongate area measuring some 9 km by 6 km in surface dimensions. Recorded gold production of 720 000 ounces along with current resources in the order of 340 000 ounces highlight the significance of this district. Historical antimony production is estimated at in excess of 50 000 metric tonnes. Significant tungsten of over 2000 t in the form of scheelite has also been produced from the field. Mineralisation is developed in veins, vein breccias, sheeted veins, network stockworks and as alteration sulfide haloes to the main structures. The vast majority of fissures are subvertical and vary in widths of up to 20 m in places. Paragenetic studies have previously indicated that the earliest mineralising event was a scheelite-bearing phase of quartz veining. Subsequent phases of arsenopyrite-pyrite-quartz-carbonate veining were accompanied by gold and minor base metal sulfides. Alteration is typically sericite-ankerite-quartz. Overprinting stibnite-quartz veining with gold-electrum, aurostibite and arsenopyrite form an important subsequent phase. Veining can be inferred from historical records to extend for vertical depths of over 1 km.

Jan 1, 2004

The Late Permian intermediate to silicic talc-alkaline Drake Volcanics of New England, N.S.W., consist largely of shallow marine, redeposited volcaniclastic rocks which host epithermal Ag-Au deposits. Pervasive hydro- thermal alteration is widespread. The 200-300 m Cataract River Member includes several sedimen- tation cycles composed of massive pumice brec- cias, overlain by laminated sandstones and siltstones, interbedded with marine, fossil- iferous mudstones. Two distinct groups of cla- sts exist within the volcaniclastic beds: 1. Lithics of predominantly intermediate compos- ition lavas that have undergone subaerial epi- clastic erosion and transportation; 2.Pumice, quartz and plagioclase crystals which have not been reworked by epiclastic processes. The lithic clasts were derived locally in a sub- aerial environment within the Drake Volcanics, and pumice and crystal fragments from contem- poraneous centres of silicic volcanism else- where in New England, N.S.W. The latter group of clasts was transported to Drake by Plinian airfall or rafting, and fell and was washed on- to emergent portions of the Drake Volcanics, where reworked locally derived fragments occ- urred. Cold state subaqueous mass-flows, prod- uced by slumping, resedimented the mixed vol- caniclastic detritus into the marine basin in a series of cyclic units with massive lower parts, and laminated upper zones. Modern ana- logs of the palaeogeographic setting in New England, N.S.W., in the Late Permian are pro- vided by the Taupo Zone, New Zealand, and sou- thern Kyushu, Japan.

Jan 1, 1987

Variations in delay timing can have a marked influence on blasting effectiveness and, hence, on total production costs. In single-row bench blasts, delay firing is invariably more effective than simultaneous initiation. In single-row delayed blasts, there is an optimum inter-hole delay above and below which inferior blasting results are obtained. This optimum delay is equal to the time required for each charge to just effectively detach its quota of the burden. The inter-hole delay should seldom be less than 4 ms.m-l of burden.In multi-row blasts in which holes in a given effective row are fired on the same delay, the entire burden on any effective row should be detached from the rock mass just before charges in the next effeotive row detonate. Delays shorter than this give inferior blasting results and an increased likelihood of environmental and slope stability problems. If the inter-row delay is too long, cut-offs can occur, especially where the delay unit is located outside the blasthole. For a surface delay system, the optimum inter-row delay usually varies between 4 ms.m-l and 8 ms.m-l of effective burden. The number of rows that can be fired effectively with surface delay systems (in a single blast) is limited by the threat of cut-offs. Greater interrow delays and a larger number of rows per blast can be fired to advantage with down-the-hole delay systems.There are practical limits to the timing accuracy of all available delay systems. The existence of delay time variability should be recognized and duly considered in the design of blasts.The relationship between delay timing and blasting vibrations is not discussed.

Jan 1, 1977

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

Declines for both access and rock haulage are replacing shafts for mining relatively shallow deposits of down to 1000 m below surface. Where the orebody does not outcrop and where surface access may be restricted, it is often necessary to drive long dead end headings before a connection can be made back to surface and a ventilation circuit created. In hot tropical areas and where large diesel powered equipment is used for mining, heat may also be a problem at these relatively shallow depths. The normal design criteria based on statutory limits and good practice used to evaluate ventilation and cooling requirements in terms of air velocity, dust, gases, diesel exhaust dilution, re-entry after blasting and heat stress are described in this paper. These are then used to design and cost alternative auxiliary ventilation systems that include leakage based on general fan performance curves and typical duct systems. The implications of the current European Community recommendations regarding nitrous fumes are also briefly considered. The actual problem relates to a 2100 m long decline that may have to be extended to 3000 m long without a connection to surface or through ventilation and is located in a hot tropical area where the surface wet bulb temperatures may exceed 25¦C for more than a third of the summer period. Once the preliminary ventilation design is completed, the auxiliary ventilation system can be modelled and simulations undertaken that incorporate heat and moisture transfer routines with the objective of determining the cooling load and amount of refrigeration required. Cognisance is taken of cyclic diesel operations and the thermal flywheel effect of the surrounding rock on the wet and dry bulb temperatures resulting from these operations.A suitable modular cooling system located at the portal is described and optimised with capital and operating costs of both the ventilation and cooling systems provided.

Jan 1, 2005

By F R. M Pires, R M. Carvalho

Supergene processes in banded iron formation (BIF) result in important dissolution, material transport and simultaneous disorder of the residual bands. The rock physical properties such as density, porosity and rheology change during the weathering attack. The itabirite, Paleoproterozoic metamorphic BIF from Quadrilßtero Ferrffero (QF) û Brazil, shows several weathered facies. Strong linking between topographic surface, rock density and iron grade occurs within the weathered zones. This linking is due to partial dissolution of silica and carbonate from itabirite and gravitational rotation and break of the remaining blades, generating kink-like slump structures. The original itabirite density, 3.7 t/m3, decrease at the first leaching steps, until 2.7 t/m3, and increase at the end of the leaching process until 3.6 t/m3. Iron grade increases from 38 per cent to 68 per cent and depressions (sinkhole), subsequently filled by Cenozoic basinal sediments, are developed over the enrichment zones. The formation of important supergene iron ore deposits of QF is intimately related to such a process. Several iron deposits at QF, such as Pico do Itabirito, Fßbrica Nova, Casa de Pedra, Tamanduß, -gua Claras, Cappo Xavier, etc., reveal the aspects related to the proposed evolution, implying that the formational process of the soft iron ores had a regional character. Granular medium model helped in the understanding of the development of the structure and the formation of the deposits. A numerical model has been developed in order to simulate a leaching system in a two-dimensional matrix, composed of two types of materials: leachable and unleachable. Equal volume proportion and vertical banding were considered. Drilling data was used as multipoint attractors to remove leachable matrix nodes.

Jan 1, 2002

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003

By T Baumgartl, T Huynh, K Tungpalan, E Wightman, M Edraki, M Tayebi-Khorami, L Huang, S Palaniandy, E Manlapig

With the increasing rate of tailing production worldwide there is a growing concern about the hazards of tailings storage facilities (TSF). Past and current mining, processing and waste disposal strategies that focus on the extraction of the valuable minerals, and an economic assessment only, are no longer suitable. Social implications and environmental legacies must be included for effective evaluation. This is possible by using an integrated assessment framework to evaluate more alternatives, including the production of additional saleable and benign streams, alternative tailings treatment and disposal as well as options for reuse, recycling and preprocessing of existing tailings. Tailings are not viewed as a final waste product but as part of the resource. From the sustainability perspective the models developed in integrated research programs will contribute to more effective methods for assessing different scenarios and potential processes and lead to better environmental management, increased production of benign tailings and improved efficiency of water and energy use and thus more responsible resource stewardship of the ore resource.This paper presents preliminary results from a multiyear research program on integrated tailings management at the Sustainable Minerals Institute (SMI), The University of Queensland, called ‘Designer Tailings’. The project involves the gathering of experimental and observational information on tailings biogeochemical processes to design and modify the range of activities within mineral processing plants, upstream characterisation ore and gangue, and downstream tailings management for desired tailings properties and outcomes. This information will assist the development of new total integrated value chain CITATION:Edraki, M, Huynh, T, Baumgartl, T, Huang, L, Andrusiewicz, M, Tungpalan, K, Tayebi-Khorami, M, Wightman, E, Palaniandy, S, Manlapig, E, Evans, C, Farrokhpay, S, Bradshaw, D and Vink, S, 2014. Designer tailings – an integrated model for tailings management, in Proceedings Life-of-Mine 2014 , pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By T M. Nester, D J. Reardon, A N. Page, B J. Barsanti

The load capacity of a friction bolt has long been regarded as 4 t/m of embedment for ground support design analysis and supported by in situ pull test results. In recent years, the authors have observed lower pull test results or inconsistent results which were rarely sighted in the early 2000s. The lower pull test results indicated in some cases that reliable friction bolt capacity (≥90 per cent of results) is closer to 3 t/m of embedment with some geotechnical engineers adjusting the ground support parameters in the design work accordingly. This can be in contrast with other mines which reliably obtain 4 t/m (or greater) using the same suppliers bolt in similar ground conditions. This raised several questions: • What is the effect of poor installation (bolt twist or bolt hole deviation)? • Does the performance of friction bolts vary in different rock masses? • Does bolt performance vary between suppliers? • What effect does increased jumbo feed/percussion/rotation settings have? • Have the bolt dimensions or steel strip width changed? • Have the physical bolt properties changed? • Have the steel properties changed? This paper was aimed to answer as many of these questions as possible and discuss each variable in detail. This project included friction bolt trials at various mine sites across Australia, multiple friction bolt manufacturers, steel manufacturers and laboratory analysis. The paper also includes discussion on what the authors consider best practice for pull testing. It should be noted, the terms ‘friction stabiliser’ and ‘split set’ used in this paper are used in a generic manner and is not linked to any specific ground support supplier. Whilst its acknowledged within the industry the term split set and friction stabiliser is used interchangeably, the authors acknowledge that the term split set is a trademark of Split Set Mining Systems and has been used in context in this paper.

Nov 29, 2022

By B Murphy

Safescape Laddertube provides an improved system for emergency egress in ventilation shafts. The addition of Laddertube in a rise has very little impact on ventilation flow, studies have indicated that the difference in flow velocities are difficult to measure due to the minimal impact. Due to the size and open-ended nature of Laddertube, the air velocity inside and out of the Laddertube is mostly linear. Laddertube can be used either permanently or during an emergency as a secondary ventilation duct. One project involved a 385 m ladder installed in a surface return air raise that could be made to bypass the primary circuit and supply fresh air to a sea container fresh air base at the bottom of the raise. Laddertube has been designed to be installed to any feasible length and can be fitted with a climb assist system ensuring enhanced speed and reduced fatigue during ascent. The climb assist used in association with Laddertube is a Tractelift system which applies a weight relief of up to 36 kg off the climber’s body weight when using the ladder. This system has successfully been tested for ladders up to 600 m in length and is currently in use for a ladder of 185 m length. The use of refuge chambers in underground coalmines has long been a contentious issue due to the concern that while it may provide temporary shelter, the risk of being exposed to high heat or the inability for rescuers to access them due to fire or explosive atmosphere means that they may be effectively trapped. The additional application for coal environments includes Laddertube installed alongside a refuge chamber concealed behind a blast proof door ensuring a secondary means of emergency egress. In certain operations designs may allow for this chamber to be provided withpositive pressure fresh air.

Oct 12, 2022