Search Documents

By M Goers, M Almond

"The use of reverse circulation (RC) drilling for grade control sample collection was selected by the Pueblo Viejo Mine Geology department at the recommencement of the operation in 2010. This method was selected because it allows: for multi-bench drilling (60 m hole depth, four benches of mining) to aid mine planning and provide a detailed close spaced drill data comparison with the reserve model angled drill holes to optimise the drill hole interception of the vertically controlled mineralisation dry sample collection in areas of excessive surface and groundwater mining operations to commence with the long assay return period (due to the need for the samples to be shipped overseas for analysis) until the on-site laboratory is operational.To date, 118 302 m of drilling has been completed throughout the operations of two open pits: Monte Negro and Moore. Two drill rigs (contractor and site-owned and operated) with three generations of sampling systems have been used to date. Throughout the drilling a 20 per cent quality assurance, quality control (QAQC) sample check (blanks, field duplicates and standards) have been used to check the drilling and laboratories performance. In addition, a total of 1104 fines samples were collected to compare the drill chip samples collected and the fines lost with two of the sample systems used.The drilling to date has highlighted the need for a complete and coordinated system to be used before sufficient confidence in the quality of the samples collected is achieved.The complete system must be set-up and coordinated to obtain the best quality sample possible. This complete package includes: drill bit size and shape for the rock being drilled and mineralisation targeted face sampling hammers with the correctly sized hammer shrouds sample hose routing to reduce sample flow turbulence and choking blow-down valves to eliminate drill hole water that has entered the drill string during rod changes correct drilling techniques targeting sample quality a sample system that captures the fines for inclusion into the sample.These improvements can be obtained without reducing the drilling rates.The measurements required to demonstrate the improvement in the sample quality will be the focus of future work within the department.CITATION:Goers, M and Almond, M, 2012. Bit to bag - The importance of a total coordinated system in reverse circulation drilling, in Proceedings Sampling 2012, pp 65-72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By E J. Hofmann, J E. Hofmann, A J. Hofmann-Fritz

"With its Head Quarters in Perth, global heavy engineering company Hofmann Engineering is one of the largest family owned engineering companies in Australia. The company has pioneered a number of new manufacturing processes and design improvements for components of large comminution equipment.Some of these innovations are: Innovative design improvements of high pressure grinding roll (HPGR) forged steel tyres. Hofmann Engineering has developed unique patented tungsten carbide stud and edge protection designs which improve wear life and introduce quick and cost effective replacement options to further extend the life of the tyre. Development of forged fabricated mill heads using rolled and welded high tensile steel plate as an alternative to cast conical mill heads. Establishment of Australian capability to manufacture and export up to 42 ft. (12.8 m) diameter SAG mill shells. Techniques for fast track, product improved replacements of cracked or damaged mill gears, including in situ profile & wear measurements of girth gears using portable coordinate measuring machine (CMM) technology, forged rim steel and induction hardening technology. Gear and pinion mechanical drive designs to 24 MW or higher for SAG mills of 38 ft. to 42 ft. (11.6 m - 12.8 m) diameter as reliable alternatives to gearless drives.The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering on large, high powered equipment for both the domestic and export markets.CITATION:Hofmann, E J, Hofmann, J E and Hofmann-Fritz, A J, 2013. Australian innovations in high pressure grinding rolls and large grinding mill manufacture, in Proceedings MetPlant 2013, pp 141-151 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By D M. Hunter, S M. Iveson, K P. Galvin

For low density materials such as coal, density-based fractionation of particles via the sink-float method is relatively simple due to the availability of liquids of suitable density; however, for high density minerals, suitable heavy liquids are less available and those that are available are expensive and pose significant hazards. At best, sink-float separation can be performed up to densities of 4400 kg/m3 with the use of Clerici’s solution at elevated temperatures. Hence the direct measurement of grade-recovery and density-partition curves is problematic. Therefore, in most cases, beneficiation plants must rely on methods such as QEMSCAN, density tracer particles or very limited information to guide them in the design and optimisation of their plants.This paper describes a density-fractionation method utilising laminar flow through a system of parallel inclined channels to generate a series of overflow fractions at different flow velocities. Here the particles are subject to precise hydrodynamic forces with minimal dispersion or mixing. The size distribution of each overflow fraction at a given flow velocity is obtained using a laser particle size analyser, and combined with a laminar flow model to deduce the corresponding density distribution. The paper describes the application of the method to measure the separation achieved using a REFLUX Classifier to obtain the corresponding feed, product and reject ‘washability curves’, and in turn the full partition surface. Approaches used to corroborate the findings are discussed.CITATION:Hunter, D M, Iveson, S M and Galvin, K P, 2017. A batch elutriation technique for the density-based fractionation of iron ore, in Proceedings Iron Ore 2017, pp 195–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Burns K. L

Keyboard patterns of hundreds of minor faults with vertical displacements of 3 mm to 2 m occur within the Greta coal seam and cause serious mining problems in collieries. Many of the faults are concentrated in linear zones termed swarms. One swarm is 600 m wide and more than 800 m long and others are of comparable size.The minor faults between the swarms are normal and are relatively widely spaced and show dip-slip movements, but the faults within a swarm are clustered and show strike-slip and oblique-slip movements. Fault swarms ofthis size and frequency have not previously been described from the Sydney Basin or on a comparable scale elsewhere but appear to be a widespread phenomenon in Australian coalfields. The faults are assigned to classes onthe basis of orientation which are then assigned to sequential phases I to IV on the basis of offsetting relations between representatives of each class. Phase I faults are minor thrusts. Phase IT, Ill, and IV faults are concentratedin the swarms and show sinistral strike-slip and normal dip-slip movements. The interference of slickenlines indicates that multiple movements have occurred within a single phase; their order is (i) strike slip (ii) dip slip and (iii) oblique slip. All faults truncate and post-date both cleat and sedimentary "stone" dykes.Phase I minor thrusts trend at a high angle to the Hunter Thrust and are considered to predate the Late Permian movements on the Hunter Thrust. Phase II and III minor faults are younger and may be any age between the latePermian and Tertiary.

Jan 1, 1978

ZINC concentrate, produced at Zeehan by flotation from Read Rosebery ore, is also dried and roasted at the same place for the production of a calcine suitable for use in the electrolytic zinc process at Risdon, Tasmania.DRYINGThe concentrate, dewatered to 12% moisture by an American filter, is fed into a dryer, the type of construction of which is similar to that of a duplex Edwards furnace. The dryer is 45 ft. long and 14 ft. wide, and has two rows of nine rabbles each, the two pairs nearest the firebox being watercooled.The longitudinal distance between rabble-centres is 4 ft. The rabbles are rotated at a speed of 3 r.p.m. by a I5-h.p. motor. Zinc concentrate is introduced by a screw feeder, consisting of two parallel-blade conveyors, revolving in opposite directions at aspeed of 31 r.p.m.Draft is supplied by a Sirocco fan, 15 in. intake, operated at 1340 r.p.m. by a 10-h.p. motor. The dust carried by the exit gases is removed in a wooden scrubbing tower, 3 ft. 6 in. x 4 ft. 6 in. x 27 ft. high, to which the fan delivers, and down which water issprayed.Wood (eucalyptus timber) is used as fuel, the consumption per ton of water evaporated being 0.55 :ton. Zinc concentrate from the dryer passed either to trucks for shipment or to Herreshoff furnaces. The portion for shipment is withdrawn at a point half-way down the furnace, being loaded on to a belt conveyor for transfer to railway trucks. The moisture at this point is 7% to 8%.

Jan 1, 1927

By M D. Taylor, G Duclaux, K Atkinson, L A. Fisher, A R. Latham, M F. Gazley, S J. de Beer, C M. Tutt

Geological logging by mine and exploration geologists involves the application of a logging code that requires a geologist to make a subjective decision to classify a particular rock unit. This will most likely result in inconsistencies in logging that will be difficult to monitor or assess over time. A potential solution to this problem is to have an objective method to determine the true nature of a given rock unit. This can be achieved using portable X-ray fluorescence technology (pXRF), as large geochemical data sets can be collected rapidly and at low cost. Plutonic Gold Mine (Plutonic), Western Australia, has a growing data set of more than 150 000 pXRF multi-element analyses from core and underground face samples, reconciled to Au fire-assay concentration, and logging codes. This study investigates and statistically validates the consistency with which the logging codes have been applied at Plutonic for the last four years, with respect to both Au distribution and other elements. In doing so, we have developed a schema that allows objective logging to occur once core has been sent for assay and analysed by pXRF. While far from replacing the geologist in the field, this is a complementary method that adds significant value to a data set.CITATION:Gazley, M F, Tutt, C M, Latham, A R, Duclaux, G, Fisher, L A, Taylor, M D, de Beer, S J and Atkinson, K, 2013. Objective geological logging using geochemical multi-element data - Plutonic Gold Mine, Western Australia, in Proceedings World Gold 2013 , pp 455-462 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By M M. Hilden, M S. Powell, B Foggiatto

In an environment of decreasing ore grade, increasing costs and uncertainty with respect to commodity prices, the industry could benefit from evaluating alternative technologies and innovative circuit configurations. The flexible circuit approach suggests that the design of grinding circuits can be adapted to changes in feed properties and economic conditions. Advances in modelling and simulation are enabling metallurgists to predict the performance of more complex circuit configurations with increased confidence. Ore variability information and processing costs may be used as modelling inputs to determine the optimum processing conditions at a given time. A case study has been completed demonstrating the value of combining a flexible circuit with a model-based optimisation of the process. Ore properties and equipment performance data obtained in operating plants have been used to model and simulate flexible circuit configurations.This paper explores strategies to introduce flexibility to existing circuit configurations when processing ores with high variability. Multicomponent models incorporated in the model developers’ kit (MDK) allow the simulation of more complex and flexible circuits. This capability enables demonstration of the potential to enhance metal production through adapting processing routes according to the ore type being processed. The simulation of different flow sheet configurations allowed the definition of the best option for maintaining the metal production when treating lower grade ores, highlighting the advantages of flexible circuit configurations compared with a one-process-fits-all approach.CITATION:Foggiatto, B, Hilden, M M and Powell, M S, 2014. Advances in the simulation of flexible circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 391–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M A. Jardine, J A. Miller, M Becker, M Harris

"Although the role of texture has been increasingly recognised as a geometallurgical indicator of ore characteristics and their variability, the ability to appropriately quantify and correlate it with metallurgical performance remains an ongoing challenge. In this study, we propose the 3D characterisation and quantification of ore textures from drill core using X-ray computed tomography (XCT) with an appropriate image analysis methodology (grey level co-occurrence matrices, GLCM). This methodology has been specially customised for application of 3D XCT grey-scale volumes. This approach has potential as an online mine site analysis tool providing detailed 3D information on both quantitative texture and simple mineralogy.The approach is illustrated in this paper using drill core samples that were manually extracted from various rock types and textures representing the Nkomati Main Mineralized Zone (MMZ) sulfide nickel ore deposit. A preliminary classification of the samples was performed based on their particle size distribution after laboratory scale rod milling. Accompanying QEMSCAN analyses were also used to guide the interpretation of the grey-scale mineralogy and texture in the 3D XCT volumes. The resultant GLCM produced from quantitative 3D image analysis of the XCT volumes indicated sensitivity to ore variability and was able to capture a simple mineralogy and grain size distribution. The approach holds many possibilities for geometallurgy, of which the potential for automation is promising.CITATION:Becker, M, Jardine, M A, Miller, J A and Harris, M, 2016. X-ray Computed Tomography – a Geometallurgical Tool for 3D Textural Analysis of Drill Core?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 231–240 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J M. F Clout

The low-grade clay-rich -1.0 mm fraction of fine iron ores have often proved difficult to upgrade and capital intensive to process when using traditional wet beneficiation technology including single or two stage hydrocyclone desliming, wet high intensity magnetic separation (WHIMS), spirals and final dewatering using fine screens. Very fine (<0.010 mm) clay-rich slimes simply follow the water split to the hydrocyclone underflow where it often impedes the subsequent processing performance of any downstream spirals and can result in troublesome direct dewatering of hydrocyclone underflow. The -1.0 mm fraction in goethitic iron ores is typically considered as waste. A new two-stage wet gravity separation flow sheet, referred to as the ædesandÆ process, has been designed to overcome these issues for the upgrading of low-grade clay-rich goethitic or hematite-quartz fine iron ores. The desand process is designed to treat the -1.0 mm range from -8.0 mm natural fines, to recover a -1.0 +0.038 mm higher-grade fraction by rejecting to tailings any low-grade clay-rich ultrafines and low density sand-size fine chert/quartz gangue and shale.The desand process consists of wet screens with a nominal 0.7-1.0 mm cut point which direct the undersize to hydrocyclones. The hydrocyclone underflow is then fed to upcurrent classifiers where the classifier middlings is sent to spirals and classifier and spirals concentrates are then dewatered using vacuum belt filters or fine screens. The three product upcurrent classifier is employed to further deslime the hydrocyclone underflow, producing firstly a coarse final concentrate, and then a deslimed middlings for feeding to spirals as well as a 0.100 mm clay and fine quartz or banded iron formation (BIF) sand in final overflow for feeding to the residue thickener. The upcurrent classifier middlings provides the spirals with a significantly cleaner feed material than traditional methods, with the end result that the spirals do not silt up with slimes and therefore can continue to run at their optimum. The upcurrent classifier and spirals form a complimentary pair, with the upcurrent classifier better able to send coarser, acceptable grade particles to concentrate and fine slimes to tailings whilst allowing the spiral to better reject coarser, subgrade low specific gravity particles. Test results for the Mayoko-Moussondji iron project, Republic of Congo, using upcurrent classifier-Wilfley Table (simulating spirals) gave acceptable mass recovery from run-of-mine (ROM) and Fe recovery from hydrocyclone underflow for HEMCOL (6.2 per cent mass recovery from ROM/43.1 per cent Fe recovery) and HEMBIF2 (5.1 per cent mass recovery from ROM/22.3 per cent Fe recovery) mineralisation types. The desand process also enables improved dewatering of -1.0 +0.038 mm product from a clay-rich plant feed.A number of new wet plants in the Pilbara use the desand flow sheet including FMGÆs Cloudbreak and their two Christmas Creek plants. Many potential new applications are being explored, with new iron ore plants in India as well as those being proposed for West Africa. Operational experience has highlighted the importance of providing clean process water to the upcurrent classifiers as well as ongoing design improvements including increased wear life, reduced maintenance and enabling a more steady feed rate to spirals.CITATION:Clout, J M F, 2013. Beneficiation of fine iron ores using the desand process, in Proceedings Iron Ore 2013 , pp 337-348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By C Li, D O’Dea, R Moreno-Atanasio, T Honeyands

The behaviour of iron ore granules in the feeding process of sintering is significantly influenced by the material properties of the granulated mix. Therefore, the measurement of key material properties of the iron ore granulated mix is indispensable prior to the simulation of the sintering process based on the discrete element method (DEM). In this paper, three key property parameters of the iron ore granulated mix, apparent density, elastic modulus and rolling friction coefficient, were measured in laboratory-scale experiments. For different sintering processes, the moisture content of the granulated mix normally varies according to the specific requirements for granule size distribution and operating conditions. Therefore, understanding the effect of moisture content on the property parameters of iron ore granules is very helpful in accurately determining the property parameters for DEM simulation work. In this paper, six groups of iron ore granule samples with six levels of moisture contents were prepared through granulation and the trends in apparent density, elastic modulus and rolling friction coefficient with the increase of moisture content were plotted and analysed based on the measurement results. The results show that as moisture increases from 6.9 per cent to 9.1 per cent, the apparent density decreases from about 3000 to 2800 kg/m3. With moisture increasing within the same range, the elastic modulus first decreases from over 200 MPa to below 100 MPa and then reaches a relative constant value of about 40 MPa at higher moisture contents. Rolling friction coefficients are measured using two methods with both indicating a similar trend, with the rolling friction coefficient first decreasing and then rising as moisture increases from 6.9 per cent to 9.1 per cent. The relationship between µr and µ’r is assumed to be similar to that between static and dynamic friction coefficients.CITATION:Li, C, Moreno-Atanasio, R, O’Dea, D and Honeyands, T, 2017. Variation in property parameters of iron ore granulated mix with moisture content, in Proceedings Iron Ore 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By I Ametov, S Harmer, R Alford

A process that allows selective flotation separation of low Cu/S ratio minerals (chalcopyrite and pyrite) from high Cu/S ratio minerals (bornite and chalcocite) from a mixed copper mineral concentrate under controlled oxidative-reductive potential conditions has been developed. The process has been extensively tested on samples with varying mineralogy using laboratory batch flotation tests and mini pilot plant trials.In this process, the mixed final copper mineral concentrate is purged with nitrogen, and then treated with sodium dithionite to achieve a slurry Eh in the -200 to -100 mV standard hydrogen electrode (SHE) range. Flotation was then carried out using nitrogen gas. As a result, a low Cu/S ratio concentrate (<1.3) and a high Cu/S ratio (>1.6) tailing stream were produced. QEMSCAN analysis of the flotation products showed that more than 85 per cent of the chalcopyrite and 95 per cent of the pyrite reported to the froth concentrate. Chalcocite and bornite were almost evenly distributed between the concentrate and tailing streams.Surface analysis studies, focused on the mechanism of separation, showed that at a negative redox potential xanthate and possibly dixanthogen are the dominant hydrophobic species on the surface of chalcopyrite and pyrite. As a result, the flotation of these minerals remained unaffected. In contrast, a much lower concentration of xanthate species on the surface of chalcocite and bornite particles was observed. Therefore, it is likely that at low Eh the copper xanthate complex desorbs from the chalcocite and bornite surfaces, causing a decrease in surface hydrophobicity and the diminished floatability of chalcocite and bornite.CITATION:Ametov, I, Harmer, S, Grano, S and Alford, R, 2014. Selective flotation of chalcopyrite and pyrite from a mixed copper mineral concentrate under controlled redox potential conditions, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R L. Chaney, M Mahoney

Mine and ore beneficiation wastes and smelter contaminated soils often cause phytotoxicity and threaten adverse environmental effects if not remediated. Science has clarified both the risks from soil metals and methods to alleviate those risks that can be applied at low cost. Phytoremediation is a family of plant and agronomy based technologies to deal with environmental aspects of sites requiring remediation. If valid risk assessment indicates that metals comprise risk, phytostabilisation may be used to alleviate that risk for most contaminated sites. In particular, Zn-Pb, Cu and Ni mine and smelter sites are readily remediated by making the soil calcareous and fertile, with added organic and metal sorbent amendments that include soil microbes to ‘revitalise’ the soil. In each case, the soil fertility and causes of phytotoxicity should be clarified by agricultural soil extractions, and the combination of amendments required to improve fertility and reverse phytotoxicity identified and found locally. In contrast with phytostabilisation, phytoextraction/phytomining uses rare metal hyperaccumulator plants and agronomic management to maximise annual phytoextraction of soil elements into plant shoots for harvest, ashing and use as a metal ore. Plants that accumulate more than two per cent Ni in shoots, and yield 10–20 t ha-1 dry biomass yield 200–400 kg Ni ha-1, which has value greater than all common agricultural crops. Considering the value of elements, existence of hyperaccumulator plants and demonstrated agronomic management for Ni phytomining, it is clear that mine sites and Ni mineralised subore-grade serpentine soils can be phytomined economically as an agricultural mining technology. A team developed agronomic methods and improved cultivars of Alyssum, which can be profitably grown on temperate zone Ni mineralised or contaminated soils. Plant species for tropical ultramafic soil materials have been identified. Phytoextraction is also strongly needed to remove Cd from rice soils to prevent human disease from soil Cd.CITATION:Chaney, R?L?and?Mahoney, M, 2014. Phytostabilisation and phytomining – principles and successes, in Proceedings Life-of-Mine 2014 , pp 3–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By W G. Rowley

The Fortescue Metals Group story began in 2003 with a vision to establish an infrastructure project that would connect the stranded iron ore deposits of the Pilbara region of Western Australia with the steel mills of Asia. Following exploration successes in the Chichester Ranges using their new exploration model, Fortescue established significant iron ore resources at Cloudbreak and Christmas Creek during 2004 and 2005. By May 2006 the definitive feasibility study for mine, rail and port was completed, many of the key government approvals had been obtained, product development and market acceptance were complete and 1.07 Bt of total proved plus probable iron ore reserves were defined to support a 20 year mine life from the Cloudbreak and Christmas Creek deposits. Project construction commenced in September 2006 following a successful $3.2 billion capital raising. By April 2008, the mine and processing plant at Cloudbreak were completed along with the Herb Elliott port facility at Port Hedland and 256 km of heavy haul railroad linking the mine with the port. Mining of overburden commenced at Cloudbreak in late 2007 and by 15 May 2008 the first shipment of iron ore had departed for China. In the first 12 months of operation total shipments amounted to 24.6 M wet metric tonnes with weighted mean composition of 58.9 per cent Fe (64.4 per cent Fe calcined), 4.3 per cent SiO2, 2.0 per cent Al2O3 and 0.047 per cent P. Exactly 3.5 years between the Cloudbreak discovery hole and commercial production. The project success depended on many technical breakthroughs including a new exploration model, application of the surface miner as the main mining production unit, design of a new marketable fines product called æRocket FinesÆ, a highly efficient ædesandÆ flow sheet for upgrading of 2.4 per cent alumina run-of-mine to 1.9 per cent alumina Rocket Fines, 40 t axle loads for the heavy haul railway and a high capacity-highly automated port facility.

Jan 1, 2009

By T Huynh, V Matanitobua, J Zheng, B N. Noller, J C. Ng, H H. Harris

A risk assessment was undertaken of the aquatic ecosystem and bioaccumulation of metals and metalloids in fish at the Leichhardt River, Mount Isa, Queensland. Residual contamination of metals and metalloids in Leichhardt River sediment was assessed and arose from mine practices using river discharge in the 1940s. The ecological risk assessment of sediments involved comparison of the concentrations of heavy metals and arsenic with those of the ANZECC/ARMCANZ (2000) Interim Sediment Quality Guidelines (ISQG). Results indicated that all sites including the background site exceeded one or both the ISQG-high and ISQG-low trigger values based on total concentrations. A lesser number of sites exceeded the ISQG-low trigger values following the 1 M hydrochloric acid extract step, which was used as an indication of bioavailability. An additional risk from particulate matter in river sediment is that acute human toxicity from the consumption of fish contaminated with metals and metalloids is unlikely. The potential risk was assessed by comparing with the maximum levels set by FSANZ (2010) for fish consumption by children and adults. In general, the liver of the fish have higher heavy metal and metalloid concentrations compared to the muscle. Frequent or regular consumption of fish from the Leichhardt River that exceed maximum levels (ML) of heavy metals and metalloids is not recommended. Risk analysis showed that an adult can consume up to 5 kg of fish fillets every day from fish caught at the man-made Lake Moondarra downstream on Leichhardt River and still be within safe consumption levels whilst a child can eat up to 1 kg daily.CITATION:Noller, B N, Ng, J C, Matanitobua, V, Harris, H H, Zheng, J and Huynh, T, ?2014. Assessment of ecotoxicology and health risk from bioaccumulation in fish of heavy metals and metalloids from historical mine practices in the Leichhardt River, Queensland, Australia, in Proceedings Life-of-Mine 2014 , pp 337–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M Davies, G Theletsane, A H. Gray

Recovery of gold from gold ores has been driven by the available technology and its configuration in the process plant flow sheet.Conventional practice in test work programs has the ore being ground fine (to 106 or 75 microns) to ensure liberation ahead of leaching or flotation. This paper identifies that, in many cases, gold and gold sulfide carriers will liberate and be recovered to a concentrate at much coarser sizes.There is an exponential increase in energy consumption relative to particle size reduction. This impact becomes extreme when comparing crushing a product to 1 mm against grinding to 75?microns.The resultant reduction in energy consumption when liberating and separating at 1 mm or coarser compared to grinding to 75 microns can be in the order of 15 kWh/t or 60 per cent of energy in the comminution circuit.Recovery of free gold and gold sulfide carriers by preconcentration (using continuous gravity devices such as the InLine Pressure Jig), combined with flotation of the fine gold and gold carriers, can result in significant power savings.There are multiple locations within the flow sheet that can be targeted using this process, including recovery in the cyclone underflow of existing plants, preconcentration ahead of the plant or complete greenfield, low-energy process plants designed from first principles based on data from a Gekko developed test work regime.We will describe the process of defining mineralogy in the laboratory and the decision-making process through to actual applications in the field.Several examples will be provided, including a South African Witwatersrand gold ore, several Australian gold ores and others, indicating the benefits of this process and where it has been brought to commercial reality.CITATION:Gray, A H, Davies, M and Theletsane, G, 2014. Coarse liberation and recovery of free gold and gold sulfide carriers for energy reduction in process plants, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 117–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

The mining of high-grade narrow vein deposits is a predominant field of activity in the precious metal sector. These types of deposits are located throughout the globe and have a significant presence in mining operations. The principle factor that has undermined the profitability and effectiveness of mining such ore zones is the substantial dilution that occurs when blasting with explosives during extraction. In order to minimise ore dilution, the thermal fragmentation mining method enables the operator to extract a narrow mineralised corridor, 30 cm to 1 m wide (according to the true width of the ore vein). By inserting a strong burner powered by diesel fuel and air into a pilot hole previously drilled directly into the vein, a thermal reaction occurs spalling the rock and enlarging the hole to 30 - 100 cm in diameter. This patented method produces highly concentrated ore, resulting in 400 - 500 per cent less dilution when compared to conventional mining methods. The mining method was conceived with the aim of mining ounces, not tonnes. This method of extraction, reduces the environmental impact of mining operations since much smaller quantities of rock are displaced, stockpiled, and treated using chemical agents. The fully mechanised equipment operated by a two-person team, maximises the effectiveness of skilled personnel, increases productivity, and reduces risks of injuries. Important economic benefits are generated for large- and small-scale mining operations alike. For large-scale operations, the mining method increases mining reserves, lowers the cost per ounce, and increases the total profitability of existing mine operations. The method also significantly lowers costs and risks of developing and mining small-scale deposits, requiring less investment capital, shortening the payback period, thus reducing the lending risk.  Combined with a small modular processing unit able to process between 100 - 300 tons per day, the method substantially lowers the financial break-even point for small-scale mining operations in a narrow vein environment. The company has been working with the technology at its Rocmec 1 mining site; results achieved and future developments are discussed.

Jan 1, 2008

Remnants of Plio-Pleistocene hot spring systems in Northland, New Zealand contain sulfide minerals, principally pyrite, marcasite and cinnabar. The climate is warm temperate to subtropical, with up to 3 m of rainfall per annum, and rocks are deeply weathered. Decomposition of the iron sulfides in natural outcrops and human excavations results in acid rock drainage with pH typically between 2 and 5, and locally down to pH 1. Deeply weathered basement greywacke is clay-rich and has negligible neutralisation capacity. Some overlying volcanic flows have resisted weathering, and pH is kept near neutral by relict secondary calcite in small areas. Natural rainforest soils commonly have pH between 4 and 5 over mineralised and unmineralised greywacke. Mineralised zones are enriched in arsenic, which occurs in solid solution (up to 1 wt per cent) in sulfides and phosphate minerals. Mercury also occurs in solid solution in some of these minerals, as well as in cinnabar. Base metals are present in low (background) concentrations only. Decomposition of the iron sulfides and phosphates releases the solid solution arsenic and mercury into the acid rock drainage solutions. Arsenic is readily adsorbed on to iron oxyhydroxides formed in acid rock drainage situations, and can be effectively removed from the biosphere. However, this arsenic is released back into the environment if the pH rises, as adsorbed oxyanions become less strongly bound and are displaced by hydroxyl ions. Behaviour of dissolved mercury is similar to that of arsenic but less well understood in these settings. Both arsenic and mercury are readily leached into pH 6 solutions from solid material collected from acid rock drainage sites. These observations suggest that neutralisation of acid rock drainage sites is undesirable in this setting, as arsenic and mercury will become more mobile in the environment. The naturally low pH of 4 to 5 of the forest floor, or even lower pH of natural acid rock drainage, is a preferable management option.

Jan 1, 2003

By B Davis, M Wallace, J Stewart, C F Burrett, J B. Cannell

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Sepon district in Lao PDR contains 1.8 Mt of JORC (2012) compliant contained Cu resources in addition to >4.5 Moz of Carlin-like Au in a Palaeozoic sedimentary package. The Cu deposits are proximal to an EW lineament of Permian rhyodacite porphyry (RDP) intrusive centres that are characterised by intense barren quartz stockworks. The Khanong deposit (42 Mt at 3.0 per cent Cu mineral inventory) is a carbonate replacement intermediate sulfidation deposit verging on a high sulfidation environment, where abundant pyrite, copper sulfides (chalcopyrite, bornite, trace enargite), copper sulfosalts (including tennantite – tetrahedrite, colusite), and base metal sulfides (sphalerite and galena) have replaced low dipping dolomite and limestone layers, forming a manto-style orebody fed by steep dipping intensely silica-pyrite altered structures. The Thengkham deposits (54 Mt at 1.5 per cent Cu) are composed of prograde skarns (garnet, clinopyroxene) and mineralised retrograde skarns (chlorite, magnetite, hematite, epidote, sericite, talc, serpentine, carbonates, sulfides) which are irregularly and semi-continuously distributed around an elongate 4 km long intrusive centre. Thengkham and Khanong have been strongly supergene enriched, forming secondary chalcocite breccias and exotic malachite zones.The Carlin-like Au deposits display a range of stratigraphic and structural controls and lie outboard of the Cu deposits. Similar structural controls, alteration assemblages and trace mineralogies suggest that gold and copper mineralisation are temporally and genetically related. It is hypothesised that the differences in style of Cu and Au deposits across the Sepon district are related primarily to palaeodepth and proximity to the intrusive centres.CITATION:Cannell, J B, Stewart, J, Williams, P, Wallace, M, Burrett, C F and Davis, B, 2015. The Sepon copper deposits (Laos) and their relation to Carlin-like gold mineralisation, in Proceedings PACRIM 2015 Congress, pp 399–408 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M L. Leybourne

In 2012, in response to an increasing potential unfunded liability, the Western Australian Government passed the Mining Rehabilitation Fund Act 2012. The intent of this Act was to introduce an annual levy on tenements covered under the Mining Act 1978 based on the area of disturbed land. The fund generated from these levies could then be used to rehabilitate mining sites where all other options to ensure rehabilitation had been exhausted. The fund could also be used to rehabilitate abandoned sites or features which, in Western Australia, number over 10 000.The Mining Rehabilitation Fund (MRF) was implemented on 1 July 2013 for an initial voluntary year. It becomes compulsory on 1 July 2014. By the end of March 2014, nine months into the voluntary period, over $6.5 million had been paid into the fund. The incentive for tenement holders to voluntarily enter the fund was the opportunity to have unconditional performance bonds held against their tenements retired. While there will be circumstances where bonds will continue to be applied, it is the State Government’s intention to retire most of the bonds.The MRF has received mostly accolades from industry and companies that have entered. Most have found the system easy to use. The MRF was also cited as a reason for Western Australia’s improved position in the Fraser Institute’s annual survey of mining jurisdictions. Work is now starting on processes to select priority abandoned mines for rehabilitation.This paper explains the background to the MRF and its development, and reviews its implementation during the first, voluntary, year. It also discusses how the fund will be managed into the future and what this will mean for both abandoned mine features across Western Australia and any future abandoned mine sites.CITATION:Leybourne, M L, 2014. Ensuring rehabilitation into the future – The Western Australian Mining Rehabilitation Fund, in Proceedings Life-of-Mine 2014 , pp 441–448 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By S Russell

The completion of the $1.1 B Cape Lambert Upgrade project is the second ‘pillar’ in Rio Tinto Iron Ore’s expansion program that has enabled Rio Tinto Iron Ore to effectively double iron ore shipping capacity from the Pilbara between 2003 and 2009 to 220 million tonnes per annum (Mt/a), following the successful completion of the Dampier Port upgrade project two years earlier.The Cape Lambert Upgrade has built on and enhanced many of the engineering achievements of the Dampier Port upgrade project, as well as developing innovative and unique engineering solutions for this complex ‘brownfields’ project that presented its own challenges, particularly in this distinctive open-water port environment.The project was implemented in two phases to achieve an increase in port shipping capacity from 55 to 80 Mt/a – an enhancement phase and an expansion phase.The initial enhancement phase, which provided an increase to shipping capacity from 55 to 60 Mt/a, focused on increasing the utilisation and effi ciency of existing plant and equipment with a relatively small capital expenditure.The expansion phase, which provided the increase in shipping capacity to 80 Mt/a, included extending the existing iron ore wharf by 256 m to create four shipping berths, a new shiploader, an expanded stockyard (including a new fourth bucket wheel reclaimer) and a new surge bin facility to maximise outloading tonnage rates.The Cape Lambert Upgrade project was implemented whilst the port remained fully operational and continued to ship record tonnages of iron ore throughout the project duration. This achievement required signifi cant upfront planning and sequencing of construction activities to support the operation of the port. Innovative design and construction techniques were used to mitigate the impact and enable construction activities in and around the operating plant.Throughout the project, new benchmarks in engineering design and construction practices were established, which have since been adopted for new iron ore port facilities currently in planning phases.

Jul 11, 2011