Search Documents

By W. T. Hicks

Visual observation of the oxidation of columbium shows that the protective behavior noted previously in gravimetric work in the early stages of the reaction below 600°C and throughout the reaction at 640°C is associated with an adherent oxide. The fact that the oxide is seen to move outward from the metal at temperatures from 550° to 935°C implies that the reaction takes place at the oxide-metal interface throughout this temperature range. THE work described in this paper further clarifies the complex oxidation kinetics of Cb revealed, for example, by the continuous gravimetric studies of T. L. Kolski.1 Time-lapse motion picture studies reveal details of the reaction not provided by a study of the combustion products. EXPERIMENTAL PROCEDURE Cb specimens were prepared from material with the following typical analysis: 0, 0.03 pct; N, 0.002 pct; C, 0.006 pct; Ta, 0.04 pct; Fe, 0.01 pct; Ni <0.003 pct; and Cr <0.003 pct. Arc-cast ingots were swaged and cold rolled into slabs. These slabs were machined into blocks 7/16 by 7/16 by 7/16 in; 1/16-in. holes were drilled through the large face of the blocks for suspension. The samples were then de-greased and annealed 1 hr at 1200°C in vacuum. The sample was suspended by a platinum and Pt 10 pct Rh thermocouple inside a 1-in. quartz tube in a Kanthal wound furnace (2 in. OD by 4 in. long) equipped with windows 1/2 in. sq. A Cine-Kodak Special II 16 mm motion picture camera was trained on the sample through a Spencer microscope adjusted so that a magnification of X1.5 resulted on the film. Super Anscochrome film was used to record the events in color. Argon was flushed through the furnace while the sample came to temperature. The argon was then replaced by a stream of dry oxygen at 1 atm. Pictures were taken at the rate of eight per second for about 20 sec during the change of atmosphere. Then by use of a Stevens time-lapse device pictures were taken at the rate of four per minute starting within 1 min of the initial oxygen flow. In this manner continuous visual records of the oxidation of pure Cb

Jan 1, 1962

By J. P. Nielsen

When two grains in a polycrystalline specimen meet at a point in the course of grain-boundary movements, and the new boundary created at the point is one of relatively low specific free energy, a nonequilibrium boundary condition occurs. The nonequilibrium is enhanced if the other grain boundaries involved at the point of meeting are relatively high in specific free energy. The nonequilibrium results in a correction by growth of the complex grain (two subgrains) to a large size, sufficient in many cases for it to become a self-propagating unit, i.e., a recrystallization grain. This mechanism, herein called "geometrical coalescence," is proposed as a logical origin for recrystallization nuclei, particularly for secondary recrystallization. RECENT publications1-&apos; indicate that considerable progress has been made toward a complete understanding of the three microstructural processes in metals: recovery, recrystallization, and grain growth. However, a major problem persists, namely, the origin of recrystallization nuclei. It is generally accepted that once a recrystallization nucleus, a secondary recrystallization nucleus particularly, has reached a certain size, it will continue to grow at the expense of its neighbors, simply as a consequence of grain-boundary free-energy considerations. What has remained obscure, however, is the mechanism whereby such a nucleus comes into being and grows to the self-propagating size. Recrystallization Nucleation in a Two-Dimensional Grain-Boundary System In the left portion of Fig. 1 is shown schematically the meeting of grains 1 and 4 on disappearance of boundary 2-3, i.e., the boundary that existed between grains 2 and 3, as might happen in the course of normal grain-boundary migration. If, by chance —and the probability is not necessarily small— grains 1 and 4 are close together in their mutual orientations, or in some other special way mutually oriented so that the new common boundary has relatively a very low specific free energy (hereinafter referred to by s), then the grain boundary arrangement as depicted in the figure is highly unstable. This is particularly so if boundaries 1-3, 3-4, 4-2, and 2-1 are high in their s values. Assuming, for the sake of argument, that boundary 1-4 has a s equal to zero, and the s&apos;s of all the other boundaries present are equal to each other and constant, then the boundary arrangement on the right in Fig. 1 will be

Jan 1, 1955

By W. Rostoker

A STUDY of the titanium-oxygen system&apos; involved an associated series of measurements of the lattice parameters of the a and TiO phases. The results permit some interesting deductions which are herein reported. A comprehensive survey of the physical PI-operties of the phases in this alloy system has been made by Ehrlich.2 However, only impure titanium was available at that time, so that some revision of his measurements is to be expected. The lattice parameters were calculated from the high angle lines of Debye-Scherrer patterns taken in a 14 cm camera and using filtered CuKa radiation. The specimens were prepared largely by crushing and screening of lump samples which had been quenched from elevated temperatures. Only in the case of low oxygen contents was it necessary to resort to filing and annealing. The results of the lattice parameter studies are graphically presented in Figs. 1 and 2. It will be seen that oxygen produces a pronounced distortion of the c parameter of the a phase (hexagonal close-packed). The trend is in general agreement with Ehrlich&apos;s work, although the divergence of actual parameter values strongly suggests that his titanium was very impure. It will be noted that the a phase of titanium can tolerate the unusually high saturation solubility of about 34 atomic pct 0. By virtue of this unique effect, it is possible to make a calculation of the effective atomic diameter of oxygen when dissolved in a lattice with metallic bonding. This has not been possible before. Ehrlich&apos;s2 density measurements demonstrated that oxygen occupies interstitial positions in the a lattice and the trend of the lattice parameters would certainly support this. In a hexagonal close-packed unit cell the largest interstitial positions lie at (2/3, 1/3, 1/4) and (2/3, 1/3, 3/4). Accordingly, if both of these positions were occupied, the ratio of titanium to oxygen would be 1:1. The extrapolated c parameter may be taken as between 4.93 and 4.99?. The a parameter appears to reach a constant value of 2.955? at low oxygen contents. The distance of the center of a titanium atom site from the [vc2/16+a2/3-1.448] Then the atomic diameter of the oxygen atom is represented by the function: where the radius of the titanium atom is 1.448A,

Jan 1, 1953

[†ADAIR, ARTHUR C., Corp 4th Co., 1st. Training Bat., 154th Depot Brigade. ADAMS, HENRY, Major Chemical Warfare Service. ARLUCK, A. A Headquarters, 1St Corps of Artillery. ASKIN, THOMAS B. H Ensign.] [ ]

Jan 1, 1925

By G. W. Form, W. A. Spitzig

The effects of hydrogen and vacuum shtering treatments on the physical and mechanical properties of arc plasma-sprayed tungsten were inuestigated. Temperatures examined ranged from 3000" to 4000°F in vacuum and 2000" to 3000°F in hydrogen for both single and duplex sintering cycles. Densities of 92 pct of theoretical density were obtained when a long-time hydrogen treatment at 2000°Fpreceded sintering in vacuum at 4000°F for 4 hr. This cycle also produced the highest ualues for modulus of rupture and bend angle. The results of this investigation point out the desirability of using a low-temperature long-time hydrogen treatment prior to a high-temperature vacuum sinter for arc plasma-sprayed tungsten. ADVANCES in the development of arc plasma-generating equipment have provided a high-temperature heat source that makes the fabrication of tungsten shapes possible by a metallizing process. Tungsten in the as-sprayed condition is very brittle. It has a density between 80 and 85 pct of theoretical density, a lamellar structure with elongated pores, and a high interstitial impurity content. To improve these properties, sintering treatments can be applied to the as-sprayed material, similar to those used for the densification of compacted tungsten powder. However, in view of the differences in the density and microstructure of as-sprayed tungsten as compared with compacted tungsten, responses to sintering were expected to be different. EXPERIMENTAL PROCEDURES The tungsten powder used in this investigation had a particle size varying from 3 to 13 p with an average diameter of 8p. The impurity level was less than 0.1 pct. The arc plasma spraying was done with an F-40 Thermal Dynamics Corp. plasma jet. Spraying was performed in air and thus required cooling of the substrate by an air blast in order to minimize oxidation. The spraying parameters employed in the fabrication of all specimens are listed below: Power input, kw 12 Arc-gas flow, cfh 95N2 + 5H2 Powder feed rate, g per min 33 Powder carrier gas flow, cfh ION, Spray distance, in. 3 Traverse rate, in. per min 30 Mandrel speed, rpm 100 Nozzle orifice, in. 7/32 These values of the spraying parameters correspond to optimum conditions ascertained in a previous study. Sintering was conducted at 3000°, 3500, and 4000°F in vacuum (< 0.1 Hg), and at 2000 and 3000°F in hydrogen. Duplex sintering treatments investigated are listed in Table I together with the designations that will be used for reference throughout this paper. The samples were fabricated by spraying onto a copper mandrel which was removed prior to sintering. The specimens used for the sintering analyses had the shape of small hollow truncated cones 1 in. high with an inside diameter varying from 0.500 to 0.125 in. and a wall thickness of 1/8 in. Specimens for bend testing were taken from hollow hexagonal prisms 1-1/2 in. high with a 1-in. diam across the flats and a wall thickness of 1/8 in. The bend-test specimens were ground to the dimensions 0.085 by 0.350 by 1-1/2 in. Prior to bend testing 0.0025 in. of stock was removed from each surface by electro-polishing. Density measurements were made by the water-displacement method. In addition, a porosimeter was used to determine the amount of interconnected porosity for representative samples. Strength and ductility were determined from recorded values in transverse bending using a cross head speed of 0.020 in. per min. The load was applied at the midpoint of a 1-in. span. The deflection data reported herein refer only to the plastic portion of the total deflection. RESULTS AND DISCUSSION The as-sprayed samples had a density corresponding to 83 pct (l pct) of the theoretical density of tungsten. Fig. 1 shows a representative as-sprayed tungsten structure.

Jan 1, 1964

By Robert G. Nisle

In conducting a pressure build-up test on an oil well, it is often necessary to shut-in the well for a short time prior to initiation of the test. The effect of such a short tern shut-in on the resulting pressure build-up curve is derived. The derivation is based on the Kelvin point-source solution and is a straight forward extension of the fundarnental theory. The magnitude of the effect is evaluatecl and illustrated by an example. It is shown that if the production subsequent to the short term shut-in is at least 10 times the duration of the shrct-in, the effect will he less than 10 per cent. INTRODUCTION It often happens that before a pressure build-up test can be made an additional valve must be mounted on the wellhead, or on arrival at the well, it might be learned that the well had been shut-in several hours the previous day because of a shortage of tankage. In such cases the question is How will such an interruption of production affect the results of a pressure buildup test This work explains how to take account of such a short term shut-in in order that the test can proceed without further delay. The solution presented here makes use of the Kelvin point-source solution used by Horne1 in his treatment of the pressure build-up in wells. Use is also made of the super-position theorem. MATHEMATICAL DERIVATION The well is assumed to have been in production at a constant rate for a relatively long time (several days or more). It is then shut-in for a short time, after which it is again placed in production at the previous constant rate. It continues to produce at this rate until shut-in for a pressure build-up test. The Kelvin point-source solution is expressed by Eq. 1. The sequence of production rates is listed in Table I. TABLE 1 — SEQUENCE OF PRODUCTION RATES Time interval Production Rate At time AT the pressure will be the resultant of the sequence of production rates shown in Table 1. An expression for the super-posed effects may be derived from this table. (Effect of + q for T + ? T) + (Effect of - q for T + ?T-t,) + (Effect of + q for T + ? T - t,) + (Effect of - q for ? T) = Resultant........(2) The desired result is obtained by substituting the effect defined by Eq. 1 for the terms in Eq. 2. The result is Eq. 3. When the logarithmic approximation is made for the exponential integrals and the terms collected the result is Eq. 4. Let T — t2 = T = flowing time following short term shut-in t2 — t1 = 6 = duration of short term shut-in Then T - t1 = r + 6 Substitution of these quantities in Eq. 4 gives p(rw ?T) = P,, -When d<<t - AT then d—&apos;-, T— approaches 1. r + AT In this case the effect of the short term shut-in may be ignored. In order to get some idea of the numerical magnitudes involved take the worst possible case, when AT = 0, that is at shut-in. If the error is made less than some maximum acceptable value at this time, it will be less than the maximum for all subsequent times. d + r Let the difference between the value of y-— and 1 be less than 0.1. Then —6+r — 1 < 0.1 S < O.l T Therefore, if the flowing time following a short term shut-in is at least 10 times the duration of the short term shut-in, the error introduced by ignoring the short term shut-in will not exceed 10 per cent of T+AT A T

Jan 1, 1957

By K. R. Evans

The yield and fracture characteristics of a Ti-8 pct A1 alloy have been examined at room temperature as a function of exposure temperatures to 1700°F. Em-brittlenzent of the alloy is observed to occur following exposures below 1280°F, the critical temperature for formation of ordered Ti3Al particles. Presence of Ti3Al particles results in an increase in the yield and flout stresses which, for a given exposure time, are a maximum at the critical temperature. Embrittlement is attributed to the occurrence of plastically induced fracture controlled by the increase inflow stress. This interpretation is compatible with the decreasing ductility and increasing crack popagation rates observed with increasing exposure time below the critical temperature. Slip line observations and measurements of the gain size dependence of the yield stress indicate that the slip character of the alloy is not influenced by exposure treatments below the critical temperature. ThE potential usefulness of Ti-A1 alloys in structural applications has prompted considerable interest in studies of their microstructure and mechanical characteristics. The relatively recent surge of interest in the system and at the same time its complexities are indicated by the fact that despite numerous recent efforts14 there has not even been general agreement upon a phase diagram for the system. However, most of the Ti-A1 alloys of commercial interest range in aluminum content from 5.0 to 8.5 wt pct where most investigators achowledge the existence of the ordered Ti41 phase. Goldak and parrs confirmed the existence of Ti41 from X-ray diffraction analysis of the stoichiometric composition while Blackburn6 has determined its presence in commercial Ti-8 pct A1 alloys by electron diffraction analysis and dark field transmission microscopy. The embrittlement of Ti-8 pct A1 alloys was initially reported by Crossley and carew7 who showed that aging in the temperature range of 750" to 1110°F resulted in extreme brittleness. This behavior was later confirmed and correlated by Soltiss to the presence of long-range order in the commercial Ti-8 pct Al-1 pct Mo-1 pct V alloy (Ti-8-1-1) which exhibited anomalous creep and yield strength behavior at 950°F. This investigation was designed to study the mechanical characteristics of a binary Ti-8 pct A1 alloy in order to further examine the nature of the embrittlement behavior reported for the alloy system. EXPERIMENTAL PROCEDURE A Ti-8 pct A1 binary alloy was obtained from the Wah Chang Co. in the form of 0.050 in. sheet. The chemical composition of the alloy is given in Table I. Heat-treatment of the alloy was conducted in evacuated vycor capsules for the tensile sDecimens (1.25 bv 0.25 in. gage section) and in evacuated stainless steel jackets for the crack growth-rate panels. All specimens were annealed at 1700°F for 24 hr and water quenched before an exposure at elevated temperatures. Tensile testing was conducted at room temperature in an Instron testing machine equipped with a pushbutton control for instantaneous control of the cross-head motion. In this manner the change in stress, Aa, accompanying an increase in strain-rate by a factor of 10 was measured immediately after yielding. The crack growth-rate panels used were 3 by 18 in. with a precrack 0.33 in. long cut into the center of the panel. The panels were cycled at a maximum gross stress of 40,000 psi at a maximum to minimum tension stress ratio of 20. Cycling of the specimens was continued until the crack propagated the width of the panels. The crack length was intermittently measured during slow crack growth. EXPERIMENTAL RESULTS Correlation of Embrittlement to the Critical Temperature for Ordering. Blackburn6 has found that the critical temperature, T,, for the formation of Ti41 in a Ti-8 pct A1 alloy with an interstitial content on the order of that given in Table I is approximately 1245°F. The relationship between the ductility of the binary alloy used in this investigation and T, was estimated from tensile tests on specimens which were exposed for 24 hr at various temperatures followed

Jan 1, 1970

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.&apos; &apos; The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By Glenn C. Waterman, Scott Hazen

3.1-1. Purpose. Development drilling is directed towards determining the grade, volume, and three-dimensional outline of a mineralized zone previously located by exploration. It is distinguished from exploration or reconnaissance drilling, which has as an objective the discovery of new mineralized areas. A development drilling and bulk sampling program should furnish the following information: 1. Geology of the mineralized zone. 2. Quantitative data on grade and tons of material within pertinent cutoff limits. 3. Physical size and shape of the deposit. Areas underlain by waste as well as ore. 4. Mineralogica1 and metallurgical characteristics of the ore. 5. I1hysical characteristics of the ore. 6. Hulk samples for metallurgical testing and grade check. 7. Data on other factors that could affect mining operations, such as ground water, ground conditions, etc. 3.1-2. Procedures. There are numerous methods and techniques that are used to acquire pertinent data on a potential ore deposit. The total cost and accuracy of a development program depends on significant evaluation of the geology, proper selection of a drilling method, thorough analysis of sample data, and accurate evaluation of all the information. Knowledge of the geology of the mineral deposit is important in planning the development testing program and in evaluating the data obtained from such a program. Exploration work usually provides some significant information on the general size, shape, thickness, grade, and geology of the deposit. In some cases no further data are needed; in many cases geological complexities suggested by the preliminary work require further geological study. Of considerable importance may be the following:

Jan 1, 1968

By Edward W. Parker

This plant was built in 1907 at the Bankhead mines to manufacture briquettes by the Zwoyer process under license from the Zwoyer Fuel Go., of New York, N. Y. The building was constructed to contain two units, each of a capacity of 10 tons per hr.; one unit was installed at the time the building was constructed, and the second unit is now being built. The coal used is an anthracite, which is more friable than that of Pennsylvania, and, as a consequepce, a larger percentage of dust or waste is produced, which was formerly thrown upon the slack-pile as waste, but is now passed to the " dust-bin " in the breaker, from which it is conveyed to the briquette-plant. An average analysis of the coal, published by Lewis Stockett and 13. R. Warden,&apos; is as follows: Per Cent. Moisture,.........0.50 Volatile,..8.00 Fixed carbon,... 83..50 Ash,.......8.00 Total,.100.00 Sulphur,.........0.40 per cent. Specific gravity,...... 1.40 Color of ash,.white Heat value,.......14,000 B.t.u. The plant is run under two 12-hr. shifts, the force consisting of 1 superintendent for both shifts, 1 engineer for each shift, 1 briquetter for each shift, 1 helper for each shift, 1 laborer cleaning up for each shift. In the pitch-melting house, 2 men are on duty for one shift. The steam for the engine is furnished from a central boiler-plant, which also supplies steam for the breaker, the electric light and power-plant, machinery-shop, and boiler-shop. During March, April, May, and half of June, in 1907, the

Jan 1, 1909

By J. F. Myers

THE Tennessee Copper Company&apos;s operations are in the Ducktown Basin, in the extreme southeast corner of Tennessee. The ore is of the heavy sulphide type, the predominating sulphides being pyrite, pyr-rhotite, chalcopyrite and sphalerite. The gangue is a micaceous schist, with varying amounts of free quartz. The mining operation develops two classes of ore, each of which is concentrated by the flotation process in separate mills. Table 1 shows a typical analysis of the ore treated in each mill. TABLE 1.-Typical Analysis of Ore Treated Composition, Per Cent Mill Tons Capacity Cu Fe S Zn London 1,350 1.41 28.4 20.2 1.10 Isabella 850 0.69 44.7 31.6 0.31 LONDON MILL The London mill was built in 1922, with a capacity of 400 tons per day. This was gradually increased to 600 tons by 1926, to 900 tons in 1928, and to 1350 tons in 1938. Fig. 1 shows the crushing and grinding flowsheet in 1928, when the capacity was 900 tons; Fig. 2, the crushing and grinding flowsheet that was developed by 1938, for the treatment of 1350 tons per day. A comparison of these flowsheets reveals that this increase in tonnage, with a subsequent improved operation, was accom-plished with identically the same major equipment. Improving a concentrator&apos;s capacity, metallurgical results, and costs as time goes by is a commonplace practice, and is accomplished in various ways, depending upon the local conditions. The reason for presenting the data of how this was accomplished in the mills of the Tennessee Copper Co. is that a fast-running rod mill plays such an interesting role

Jan 1, 1940

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller&apos;s earths fall within the general group of bleaching clays and gradually the commercial term "fuller&apos;s earth" has been applied to natural clays originating, for the most part, in the south-eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.1 Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). TABLE 1.-Physical and Chemical Composition of Different Types of Clays Composition, Per Cent Constituents and Properties Bentonite Fuller&apos;s Mud Clay (Wyoming) Earth (P Peak)&apos; (Alluvial) Silica (SiO2) 60.0 69.6 61.67 Alumina (Al203) 19.0 14.3 20.34 Ferric oxide (Fe203) 2.8 3.90 7.70 Titanium oxide (Ti02) 0.13 0.70 1.01 Lime (CaO) 0.5 0.80 0.00 Magnesia (MgO) 2.0 1.00 0.24 Soda (Na2O) 2.4 0.40 0.31 Ignition loss 4.7 6.77 8.51 Moisture content 8.0 10.0 20.0 Isoelectric point, pH 9.2 9.2 6.5 Average swelling volume 15.0 0.0 0.0 Weight per cubic foot, lb 55.0 40.0 65.0 Material passing 200-mesh sieve, per cent 90.0 85.0 50.0

Jan 1, 1939

By J. E. Burke, A. M. Turkalo

IN 1923 Desch¹ pointed out that the grains in a metal which is anisotropic with respect to its thermal coefficient of expansion would contract differently upon cooling, and that the stresses developed might approximate the plastic strength of the metal. More recently Boas and Honeycombe2-5 studied the behavior of several metals upon thermal cycling and observed that the stresses developed in arlisotropic metals are great enough to produce slip lines in individual grains and a roughening of the specimen surface. This phenomenon they have named "thermal fatigue." The mechanism they propose involves essentially a kneading of the grains, the deformation being alternately in compression and tension in a given grain as the temperature is changed in one direction and then the other. The present work was undertaken to investigate the possibility that an additional mechanism might operate to produce plastic deformation during thermal cycling—a "thermal ratchet" that depends upon a combination of grain boundary flow to relax the stress that develops between differently oriented grains upon raising the temperature and transcrys-talline slip to relax the oppositely directed stress which develops on lowering the temperature. Thus, thermal cycling should produce a nonreversible distortion such that certain grains will change shape differently from their neighbors with a simultaneous displacement being produced at the grain boundary. Temperature Dependence of Grain Boundary and Grain Strength The critical resolved stress for the initiation of slip in metal grains is only mildly affected by temperature." For example, in cadmium it decreases from 0.15 to about 0.05 kg per sq mm when the temperature is increased from 20° to 458°K and further temperature increase causes little further decrease. On the other hand, the work of KG1 indicates that the grain boundaries behave in a viscous fashion that can be described8 by the expression: t = BVexp(Q/RT) [1] t is the shearing stress on the boundary; B, a constant; V, the flow rate at the boundary; Q, the activation energy for grain boundary flow; R, the gas law&apos;s constant; and T, the absolute temperature. Eq 1 indicates that the stress necessary to cause a given grain boundary flow rate, V, decreases rapidly with increasing temperature. The value of the constant B is such that at sufficiently low temperature and ordinary strain rates deformation will occur preferentially by slip rather than by grain boundary flow. There is considerable evidence to indicate Consider the bicrystal shown in Fig. 1. In grain 1 the slip plane lies 45 " to the boundary while in grain 2 the slip plane is 90" to the boundary. The coefficients of expansion of the grains in a direction parallel to the length of the crystal are a1 and a, with a, > a2 for the orientations shown. The sequence of events that can occur upon heating and cooling this specimen is illustrated schematically in Fig. 2. Initially there is assumed to be no stress in the specimen (A). Upon heating, grain 1 attempts to become longer than grain 2, but is constrained by grain 2. Thus grain 1 is loaded in compression and grain 2 is loaded in tension, and a shearing stress is present across the boundary (B). As the temperature is increased, the stress will build up, and finally grain 1 will be plastically deformed by slip, since the greater stress is resolved on its slip planes. Any further heating will result in more slip and the stress will remain constant until some temperature T* is reached where the stress can be relaxed by grain boundary flow.† At this relaxation temperature (C) a step will appear between grain 1 and grain 2. Further heating above T* will cause grain 1 to become relatively longer, but no stress will appear because the grain boundary is too weak to support the stress (D). Upon cooling again, at T* (E), the grain boundary will again be able to support a shearing stress, and upon cooling further, grain 1 will be loaded in tension and grain 2 in compression (F). When the decrease in temperature below T* is sufficient to impose the critical shear stress upon the slip plane of grain 1, it will be stretched by slip.

Jan 1, 1953

By O. A. Knight

THE suppression of the austenite-martensite transformation that can be brought about by the addition of certain alloying elements, such as manganese or nickel, to plain carbon steel has been known for a long time, especially since Guillet&apos;s investigation at the beginning of this century. The extent to which the critical range is lowered depends upon the percentage and nature of the special element added. First the Ar1 point is lowered gradually, then at a certain percentage a sudden lowering to about 300° C. occurs. The addition of still larger percentages of the alloy may result in lowering the Ar1 point to room temperature or below, in which case the steel remains austenitic at room temperature, especially after rapid cooling. The effect of alloying elements of this general type on the lowering of the transformation temperature is well illustrated by Sauveur(1)§ in his Fig. 281a, reproduced here as Fig. 1. This type of curve is characteristic of both manganese and nickel though it requires about 2 1/2 times as much nickel as of manganese to produce the same result. The influence of nickel in retarding the transformation of austenite into the lower transition constituents is due to its lowering of the critical range of the steel, which is also well illustrated by Sauveur(1) (after Osmond) in his Fig. 284, reproduced here as Fig. 2. Scott(15) presents a diagram illustrating the effect of manganese on the Ac3 and Ar3 points which is strikingly similar to the diagram above referred to in Fig. 2 concerning the effect of nickel.

Jan 1, 1934

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous TABLE 1.-Some Secondary Non-ferrous Metals Recovered in the United States for the Year 1924-25 Material Short Tons Value Copper, including that in alloys other than brass.... 250,600 $ 71,170,400 Brass, scrap remelted 242,300 56,270,800 Lead as metal 112,4201 39,477,100 Lead as alloys 112,460 Zinc as metal 61,430 11,359,000 Zinc -in alloys other than brass 13,300 Tin as metal 1 7,950 35,165,400 Tin in alloys 23,000 Antimony as metal 1 } 3;794,000 Antimony in alloys 10,839 Aluminum as metal 17,700 24 Aluminum in alloys 26,300 ,816,000 Nickel as metal 19 1 1,518,000 Nickel in non-ferrous alloys 2,109 Total 882,600 $243,570,700

Jan 1, 1928

By R. T. Pepper

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,&apos; and Hess and Cieorge.&apos; Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on &apos;Microcloth&apos; using a lubricant of &apos;Hyprez&apos; oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the &apos;Microcloth&apos; nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80° to 90°C. The cream is allowed to cool, and is then &apos;whipped&apos; to a smooth consistency with 100-ml &apos;Hyprez&apos; oil. Before polishing, the diamond loaded &apos;Microcloth&apos; is moistened with a few drops of &apos;Hyprez&apos; oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- ° diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By J. M. Lommel

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,&apos; and Hess and Cieorge.&apos; Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on &apos;Microcloth&apos; using a lubricant of &apos;Hyprez&apos; oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the &apos;Microcloth&apos; nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80o to 90°C. The cream is allowed to cool, and is then &apos;whipped&apos; to a smooth consistency with 100-ml &apos;Hyprez&apos; oil. Before polishing, the diamond loaded &apos;Microcloth&apos; is moistened with a few drops of &apos;Hyprez&apos; oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- µ diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and&apos; is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of&apos; Venezuela. The Welge gas-flood technique,&apos; based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.&apos; The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By R. Schuhmann

Distribution of material in the fine sizes of a comminution product generally is well represented by the empirical equation&apos; y = 100 (x/k)a [1] in which y — cumulative percent finer, x = particle size, a -= distribution modulus, and k = size modulus. Charles3 found that the energy consumption in comminution is usefully expressed by another empirical relation, E = Ak(1-D) [2] in which E = energy input per unit volume of material, A = a constant, k = size modulus based on Eq. 1, and n = a constant; (1-n) is the slope of a plot of log E vs log k. Holmes3 has presented energy equations similar to Eq. 2. The constants a and n in Eqs. 1 and 2 have been shown to depend both on the nature of the material and on the comminuting device. Moreover, Charles showed that within experimental error a and n are a — n+1 = 0 [3] Combining Eqs. 2 and 3, E = A k-a [4] In the first sections of this article it is shown that the energy equation, Eq. 4, can be derived directly from the size distribution equation for the fine sizes, Eq. 1. The derivations are made without assuming any of the specific relationships between energy and particle size which have been common in previous literature. For comminution processes in which Eqs. 1 and 4 adequately represent the experimental data, the constant A in Eq. 4 is found to be a simple and useful inverse measure of grindability. That is, A is the energy consumption per unit volume of comminution product finer than unit size as determined from the straight line portion of the log-log plot of the size distribution. These considerations all lead to a unifying hypothesis of comminution mechanism from which both Eq. 1 and Eq. 4 can be derived. Finally, it is pointed out that this hypothesis raises serious questions as to the significance of the Rittinger hypothesis, the Kick hypothesis, and other theories in which energy numbers are systematically assigned to various size fractions of comminution products in order to calculate theoretical energy consumptions. Derivation of the Energy Equation from the Size Distribution Equation: For simplicity, consider the comminution of 100 volumes of a feed material of relatively uniform particle size. The comminution process may be considered as the summation of many individual and independent comminution events. The extent of comminution is most easily expressed as the number of comminution events, z. In the first derivation, the key assumption is that the characteristics of the comminution events in a given crushing or grinding process are substantially constant and do not vary with the progress of the comminution process. Accordingly the characteristics of an average comminution event may be defined. In one such event, a quantity of energy $E is applied to a single particle of size f and volume $v. The crushing of this particle produces fine particles with a size distribution similar to that given by Eq. 1: yw=100(x/ka)a0 [51 In this equation yo, a0, and k0 are used to characterize the product of an individual comminution event rather than the product of the comminution process as a whole. In using Eq. 5, we will not be concerned with values of x close to the feed size f and will therefore assume only that the equation is applicable to the finest sizes of the material. In 100 volumes of total product, the actual volume of product finer than x from a single comminution event, or dy, is given by The total volume of material below size x, resulting from z events, is then given by y = z(dy) =z(dv) (x/ka)a0 =" Eq. 7 reduces to Eq. 1 when we let a, = a and [8a] z =100/dv (ka/k )1 or k = ka (zdv/100)-1/a [8b] Eq. 8a shows that the distribution modulus of the comminution product is the same as for the product of an individual comminution event. Eq. 8b shows how the size modulus of the comminution product k varies with the extent of comminution as measured by the number of events, z, or as measured by the fraction of the feed actually subjected to com- minution1 zdv/100. The energy input to 100 volumes of total feed, or 100E, is the sum of the energy inputs for all the comminution events: 100E =z (dE) [9]

Jan 1, 1961

By Blake M. Loring

RECENTLY the S-curves for 30 to 40 alloy steels have been published.1,2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.20 percent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr. at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1 1/4 by 1/2 by 1/8 in. Wires attached to the samples were used for handling, instead of tongs, to avoid chilling. The specimens were heated at 845°C. for 1/2 hr. and quenched into constant-temperature salt baths held at various temperatures from 205° to 650°C. The time required to transfer the specimens was found to be about x 1 1/2 sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 21°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1941