Search Documents

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined for the system gadolinium-nickel. Nine intermetallic compounds have been found at compositions corresponding to the following gadolinium-nickel ratios: 3:1, 3:2, 1:1, 1:2, 1:3, 2:7, 1:4, 1:5, 2:17. The GdNi and GdNi5 compounds have congruent melting points of 1300' and 1500°C, respectively while the remaining compounds melt in-congruently. Eutectics exist at 15 wt pct Ni, 31 1/2 wt pct Ni and 87 wt pct Ni with melting points of 6703 8803 and 1220°C, respectively. IN a continuing investigation of the properties of rare earth alloys, a study has been made of the gadolinium-nickel system. Previous work encompassed the iron containing alloys and a subsequent paper will deal with the constitution of the gadolinium-cobalt system. Vogel,1 examined alloys of nickel with lanthanum and cerium. R3Ni, RNi, RNi2, RNi3, RNi4, and RNi5 compounds were found. Endter and Klemm,2 Fulling et al.3 Heumann,4 and Nowotny5 found the 1:2 compositions of this series to exist in a C-15 (face-centered cubic) structure, and the 1:5 compositions in a hexagonal system. Jepson and Duwez6 more recently examined these 1:2 and 1:5 compositions and generally confirmed earlier data while Wernick and Geller7 most recently have given additional data on the GdNi5 compound. Comparisons with our results will be made in the appropriate section of this report. EXPERIMENTAL Methods of alloy preparation, annealing procedures, and experimental techniques have been given in our earlier paper.8 Chemical analyses of the alloy samples were made by dissolving the specimen in nitric acid, precipitating the gadolinium as hydroxide and the nickel with dimethylglyoxime. Both precipitates were ignited to oxide and weighed. RESULTS Microstructure— Metallography of alloy specimens in this series has been conducted on both arc-melted and annealed materials. Etchants used have been 5 pct nital with approximately 10 pct distilled water added, for high gadolinium samples; Carapella's ferric chloride solution for intermediate compositions; and Marble's (copper sulfate) reagent for high nickel content alloys. Because of difficulties encountered in the grinding and polishing of specimens containing 40 to 75 wt pct Ni, no photomicrographs were made of such specimens. The microstructure of an arc-melted 5.3 wt pct Ni alloy is shown in Fig. 1. Light etching primary grains of gadolinium are embedded in an eutectic matrix. The microstructure of an alloy of 9.55 wt pct Ni alloy, Fig. 2, annealed 50 hr at 700°C, consists almost entirely of the intermetallic compound Gd3Ni. The structure of an arc metal alloy of approximately 19 pct Ni, Fig. 3, consists of grains of the compound GdNi embedded in the Gd3Ni2-Gd3Ni eutectic. The arc-cast structure of the 38.7 wt pct Ni alloy is shown in Fig. 4. Large primary grains of a compound rest in a matrix structure of coarse GdNi-GdNiz eutectic. Because of the occurrence of several peritectic compounds in the central region of the diagram, identification of the primary structure in this alloy is not certain. As has been indicated above, microstructures of alloy specimens containing between ca 40 and 75 wt pct Ni have not been photographed. These specimens were highly brittle, and macro- and micro-cracking were impossible to control in the grinding and polishing procedures. Prolonged annealing did not alleviate this condition. Visual observations in small specimens did, however, provide evidence for a multiplicity of phases and peritectic dissociations of compounds although rationalization of structures was not possible.

Jan 1, 1962

By Homer N. Mead

This report develops equations for decline curve analysis based upon the premise that the rate of change of the reciprocal of decline for succeeding time intervals is constant when the reservoir is produced under a fixed set of conditions. A method is shown for predicting maximum production rate against cumulative production for any reservoir. A method is also presented for predicting future production rate by an analysis of past production performance after decline has been esrahlished. INTRODUCTION No significant contribution to the analysis of decline curves by the loss-ratio method has been made since J. J. Arps paper1. The concept of loss-ratio that was developed by Arps and his contemporaries has been redefined in another way and the concept of instantaneous loss-ratio at time zero has been added. In the mathematical developmerit by Arps, production rate was related as a continuous function with time and his equatlons were developed on that basis. In this paper, production is considered to be a series of segments for equal time intervals and equations have been developed based upon these finite differences. It is realized that decline curve analysis is not the answer to all predictions of reservoir behavior. However, as production must decline from an initial maximum rate to zero in any reservoir, if such decline can be expressed as an infinite series, this series should accurately predict production. Decline curve analysis should be considered a valuable tool that may be used in conjunction with predictions of future recoveries by other methods. Various uses of the decline curve method will be discussed in this paper. Equations predicting production rate at any time and cumulative production by exponential and hyperbolic decline will be developed. Characteristic values of b related to various types of drive will be discussed. After that a hypothetical reservoir will be studied and ultimate recovery by natural depletion and pressure maintenance compared, then actual field examples will be shown and discussed. The rate-cumulative curve introduced by H. N. Marshs in 1928 is an important one for use in estimating future production rate and ultimate recovery. This graphical method is the one that is used in conjunction with the equations to be developed for predicting production behavior. EXPONENTIAL DECLINE In exponential decline each succeeding production rate per unit of time is a constant percentage of the production rate just before it. Since (1 — r) is the common ratio, where r is the constant decline rate, this condition may be expressed as a geometrical progression; thus Pn = P (1 - r)n-1 . ......(1) Where r is less than unity, r Since P1 (1 - r)n = Pn+1 P1 - Pn+1 C =P1-Pn+1/r........(2) LOSS-RATIO In this paper the calculation for loss-ratio has been changed from the method presented by Johnson and Bollens2. The first loss-ratio to be calculated is a,; it is the initial production per unit of time after decline has set in divided by the difference between the initial and the second production rate. This loss-ratio is for the first time interval. After b (which is the constant change

Jan 1, 1957

By H. Siebel, N. A. D. Parlee

MIZIKAR, Grace, and parlee' studied rates of absorption of oxygen in stagnant liquid silver in a new type of open-ended gas-liquid metal diffusion cell, where the capillary diameters used were 1.5, 2, and 3 mm. They reported that the rates appeared to be controlled by the rate of diffusion of oxygen atoms in liquid silver and they used their data to arrive at the following equation as a reasonably good representation of the diffusivity (D) of oxygen in liquid silver: D = (14.7)10-4 exp (-7100 ± 3200)/RT cm2/sec Since this type of diffusion cell offers a promising method of measuring diffusivities of gas atoms in liquid metals, the senior author of this note and his students are carrying on a critical examination of the method, and are attempting to improve and extend the technique. The research reported briefly here was designed to examine more carefully the earlier conclusion1 that the absorption rate is diffusion-controlled, and to find out whether the diameter of the cell could be greatly increased and thus extend the method to systems where gas solubilities and diffusion rates are much smaller than in the case of oxygen in silver. For the purpose of these experiments, the open-ended capillary cell used by Mizikar, Grace, and Parlee was replaced by a small cylindrical crucible (1 to 1.7 cm in diam) containing pure silver (to a depth of 1.3 to 3 cm) resting in the bottom of a closed-ended vertical quartz tube, with an evacuated quartz filler tube just above the crucible to reduce dead volume. The method of measuring the rate of absorption was otherwise very similar to that of Mizikar, Grace, and Parlee and all the same precautions were taken. A much smaller and shorter tube furnace was used for heating, but simi- lar precautions about temperature gradients were observed. This technique was nothing more than the application of a Sieverts apparatus to the measurement of rates of absorption in small crucibles of stagnant liquid silver. In each run the volume of gas absorbed (V) was plotted against the square root of time (vt) and apparent diffusivities were calculated from the slope of the line, as described by Mizikar, Grace, and parlee.' Care was taken to use only the data obtained during the early part of the total absorption period while the cell functioned as one of infinite depth. The results at 1000°C are summarized in Table I and Fig. 1. The following conclusions may be drawn: 1) Diffusion cells up to 1.7 cm in diam yield, within experimental error, the same values for the diffusivity of oxygen (D) as the capillary cells of 1.5, 2, and 3 mm in diam employed by Mizikar, Grace, and Parlee. Cell diameters as large as 1.7 cm are probably not desirable for the most precise work. Intermediate sizes, perhaps 0.5 cm, will be most practical. 2) All absorptions measured were consistent with a model where the rate is controlled by the diffusion of gas atoms in the metal. The fact that runs at absorption pressures ranging from 0.1 to 1 atm (at any one temperature) give

Jan 1, 1965

By Joseph M. Jacisin

Fatigue tests were conducted on 2017-T4 alumium in alloy in an u1lrcthig.h vacuum of 2 x 10-lo Torr and in air. The vatio of vacuum-to-air faligue life for this ~malerial varied Jrom 3.5:1 at a strain of 2.5 X 1O-3 ill. pegr in. to 8:l at a strum of 3.3 x X ill. per 171. Sotlze pvelivtlinary data were also obtained on the faligue life of the alumirnum alloy in a dvy-nitrogen atmosphere. A dark deposit observed on the fracture surfaces of the aiv-tested specimens was identified as oxides of tr~angarzese and magnesium This observalion, and the close correlalion betaveen results obtained in vaCuum and dry-nitrogen environtments, tend to confirm that air stvongly influences the fatigue mechanism by a covrosion process. THE fatigue life of certain metals is known to increase when the atmospheric pressure is reduced. Gough and Sopwith1-2 postulated that this is due to a joint chemical and mechanical process operating in air at the surface of the metal with oxygen and water vapor playing significant roles. Wadsworth and Hutchings3 observed that aluminum is mainly affected by the presence of water vapor. Very little information is available on the fatigue properties of structural aluminum alloys in a vacuum environment. This report describes work performed on 2017-T4 aluminum alloy in an ultrahigh vacuum (2 x 10-loTorr) and in air. Some preliminary data are also presented on the fatigue life of the alloy in a dry-nitrogen environment. 1) EXPERIMENT 1.1) Test Material. The material tested was commerciaT 2017-T4 aluminum alloy which, in addition to aluminum, has an approximate composition of 4 pct Cu, 1 pct Fe, 0.8 pct Si, 0.5 pct Mg, 0.5 pct Mn, plus smaller amounts of other elements.* Some typical naturally age to a substantially stable condition. Specimens were then machined from these rods and ground to a No. 8 microfinish. In order to minimize variation in material characteristics, specimens were made from rods procured from the same lot. 1.2) Apparatus. The apparatus and test specimen used in the fatigue tests are shown in Fig. 1. The device utilized a single-cantilever beam with rotating-bending loading. Bending stress was applied to the fatigue test specimen by placing a spacer beneath the bearing support, thereby providing a constant deflec-

Jan 1, 1968

By D. Argyriades, G. Derge, G. M. Pound

The electrical conductance of molten FeS was studied as a function of temperature and composition. It was found that stoi-chiometric FeS (36.5 pct S) shows a minimum specific conductance of 400 ohm-1 cm-1. For the Fe-rich melts the conductivity increases with increasing amount of iron to about 4850 ohm-1' cm-I at 26 pct sulfur. For the sulfur-rich melts the conductivity increases with increasing amount of sulfur until it reaches a maximum of 1300 ohm1 cm-1 for 37.4 pct S and decreases to 800 ohm-1 cm-1 for 38.3 pct sulfur. It is concluded that molten stoichiometric FeS is an intrinsic semiconductor in which the forbidden gap in the electron energy level diagram is quite narrow. Excess sulfur acts as an acceptor impurity in providing a component of positive hole conduction, while excess iron acts as a donor impurity to increase the n-type conduction. K. Bornemann and G. von Ftauschenplatl used a four-terminal, direct-current cell to study the electrical conductance of molten copper sulfide. Their measurements showed a high conductivity, of the order of 100 ohm-1 cm-" and a positive temperature coefficient. From electrolysis studies, Savelsberg2 concluded that molten Cu2S and molten FeS are electronic conductors. Further. he found that molten FeS has a high specific conductance, of the order of 1500 ohm-' cm-', and a small negative temperature coefficient. Pound, Derge, and Osuch,3 using an ac Kelvin circuit and a four-terminal cell, measured the specific conductance of molten Cu,S, molten FeS, and various mixtures. They found that the specific conductance of the solutions followed a roughly additive rule of mixtures. Yang, Pound, and Derge4 showed from electrolysis measurements that the mechanism of electrical conduction in molten Cu2S, FeS, and mattes is primarily electronic. Further, they observed that small additions of CuCl suppress the electronic conduction whereupon the system behaves ionically.

Jan 1, 1960

By Hans Strack

Electroluminescence of GaAs p-n junctions fabricated by simultaneous diffusion of sulfur and iron was investigated at 77°K. A narrow emission peak with a half width of about 4 kT in the energy range between 1.14 and 1.155 eu was attributed to iron. Other transition elements exhibited light emission in the vicinity of the iron peak, namely nickel between 1.15 and 1.16 ev and cobalt between 1.16 and 1.17 ev. The efficiency of the doping with iron depended on the amoz~nt of arsenic present. A weight ratio of arsenic to iron of 4:l was sufficient to observe the emission lines associated with transition elements. The presence of oxygen reduces the intensity of the light emission. In addition to the levels associated with transition elements, levels at 1.05 and 1.28 ev, probably due to lattice defects, are observed except in diodes fabricated in solution-grown GaAs. THE near band edge emission of GaAsp-n junctions has been studied extensively in the past.' GaAs devices utilizing spontaneous and stimulated near band edge emission are of considerable practical importance. Typical junctions are fabricated by diffusion of a heavily doped p region into degenerate n-type GaAs. Much less work has been done on investigating the radiative recombination via deep levels in lightly doped p-type material. This area is of interest in understanding the performance of GaAs n-p-n transistors. GaAs transistors show remarkable improvement in high-frequency performance and current-gain stability at high temperatures, when iron is added to sulfur during the emitter diffusion process. The present work was initiated to investigate deep-level electroluminescence of iron-doped GaAs p-n junctions fabricated on vapor-phase epitaxial GaAs and on solution-grown GaAs. For comparison several diodes doped with cobalt and nickel were studied. Iron, cobalt, and nickel have an electron configuration of the type

Jan 1, 1968

By R. Kossowsky, W. C. Johnston

CONSIDERABLE experimental data has been published in recent years on a few directionally solidified aluminum base eutectic alloys. The mechanical properties of A1-Al3Ni eutectic have been studied by Lemkey, Hertzberg, and Ford1',2 and Salkind et a1.3 where the alloy has been demonstrated to behave as a whisker reinforced composite with superior properties over many aluminum alloys. It has also been shown4 that aluminum reinforced with Al3Ni whiskers R. KOSSOWSKY, Member AIME, is Senior Metallurgist, Westing-house Research Laboratories, Pittsburgh, Pa. W. C. JOHNSTON, formerly with Westinghouse Research Laboratories, is Head, Department of Physics, George Mason College, University of Virginia, Fairfax, Va. Manuscript submitted March 28. 1969. IMD__________________ possesses excellent microstructural stability to 508°C. The effect of lamellar structure in A1-CuA12 eutectic was compared3 to the rod-like structure in the A1-Al3Ni eutectic, and was found to be better in low cycle fatigue. This was rationalized3 by postulating that a lamellar reinforcement was more efficient at blocking lateral plastic flow than a rod-like rein-forcement. The purpose of this study is to explore eutectic strengthening in other aluminum base alloys. The Al-Pd system5 forms a eutectic with aluminum and the intermetallic compound A13Pd at 25 wt pct Pd, and has a melting point of 615°C. A13Pd has an orthorhom-bic structure and transforms to hexagonal Pd2A13 at 785°C. Growth characteristics, compression yield strength, creep rupture, and microstructural stability of directionally solidified and as-cast alloys are investigated. Eutectic ingots having a nominal composition of 25 wt pct Pd were prepared by first compacting 1/2 in. diam by a in. high pellets from 99.99+ pct A1 and 99.99 pct Pd powders. The pellets were then levitation cast into 1/4 in. diam by 2 in. long copper molds. Directionally solidified bars were prepared by grinding the cast ingots to 0.195 in. diam, inserting them into alumina

Jan 1, 1970

By Jean Howard

THERE are two mechanisms by which secondary crystals can develop in bcc alloys, namely 1) impurity inhibition and 2) strip-thickness inhibition. This paper reports some studies of each mechanism; the alloys were Si-Fe, A1-Fe, Cr-Fe, Mo-Fe, and Ge-Fe, as well as iron itself. All the alloys, which were of interest as part of a program of work on soft magnetic materials, were made by a powder-metallurgy process, using carbonyl iron (Grade MCP) as the starting material. Earlier phases of the work have already been published. Work described previously1 shows how the oxygen content of the sintering. atmosphere can be used to produce silica in the material which acts as a grain-growth inhibitor. Since then it has been found more convenient to make use of the oxide in the iron powder to control the silica content of the material. The compacts are sintered in vacuum which allows a direct reaction to take place between the iron oxide and the silicon. Details are given elsewhere.4 By this method, and by suitable adjustment of the rolling schedule, material with cube-on-edge secondary crystals has been produced in thicknesses from 0.1 to 0.001 in. in iron containing from 2-1/2 to 4-1/2 pct Si. It was also found possible to process 6-1/2 pct Si-Fe to 0.001 in. This was achieved by refinement of the sintered-compact grain size by using fine-particle silicon (i.e., <200 mesh). The brittleness of the material necessitated hot rolling to 0.020 in., from which thickness cold rolling was possible. If the conditions of sintering and the cold-rolling schedule were correct (i.e., as given elsewhere4 for 3-1/4 pct Si-Fe) secondary crystals of (110) [001.] orientation could be developed. The size of the secondary" crvstals" could not be

Jan 1, 1965

By George Branner

THERE is no record of the commercial production of bentonite as such in Arkansas up to the present although fuller&apos;s earth has been. mined intermittently in the state1 from 1891 to 1922. Very nearly all of this was obtained from decomposed basaltic dikes.2 Recently three bentonite deposits of close stratigraphical relationship have been identified in the Coastal Plain region of southern Arkansas, which suggests that there may be a considerable quantity of commercial material available. LOCATION AND ACCESSIBILITY The three deposits are located respectively in the SE. ;1/4 SE. ;1/4 sec. 13, T.- 2 S., R. 13 W., Saline County, the SE. ;1/4 SE. 1/4 sec. 18, T. 5 S., R. 16 W., Hot Spring County, and in sec. 22, T. 12 S., R. 19 W., Ouachita County. The Saline County deposit is 14 miles by state highway 167 south of the city limits of Little Rock and 1 mile west by dirt road. This deposit is 12 miles south of Ward switch on the C. R. I. P. Railroad and 11 miles east of Vimy Ridge by dirt road. Vimy Ridge is also on the C. R. I. P. Railroad. The Hot Spring County deposit located in the SE. ¼ SE. ;1/4 sec. 18, T. 5 S., R. 16 W. is about 100 yd. north of Durian switch on the C. R. I. P. Railroad and on state highway No. 9, 5 miles southeast of Malvern. The Ouachita County deposit has not been accurately located but lies in sec. 22, T. 12 S., R. 19 W. It is approximately 2 miles by road from Chidester on the Missouri Pacific Railroad.

Jan 1, 1929

By J. L. Christie

A recent case of failure of a-low karat gold alloy by stress-corrosion cracking is of interest because it illustrates a principle frequently overlooked: the relation between high residual stress and high yield point. The alloy contained Gold, per cent 39.6 Copper, per cent 51.1 Silver, per cent 5.2 Nickel. per cent 3. 1 Zinc, per cent 1.0 Tension tests on the alloy showed the following:

Jan 1, 1945

By Paul Pietrokowsky

THE formation of intermediate phases in the solid state reaction of titanium with silicon, germanium. and tin (of subgroup 4B in the periodic table) was the subject of a recent paper.&apos; Further investigation of the system Ti-Sn revealed the presence of a new compound on the titanium-rich side of this phase diagram. Metallographic evidence indicated that this new phase was situated very close to 75 atomic pct Ti. The present work is concerned with the crystal structure of the intermediate phase Ti3Sn. Iodide-process titanium metal, furnished by the New Jersey Zinc Co., was used in this investigation. The metallic tin was received in powder form from Charles Hardy Inc., New York; its purity was 99.80 pct. The titanium rod was machined into small cups 1 cm in diam and about 1.5 cm in height. The tin powder was compacted, melted, and then placed in the titanium cups and alloyed by electric arc melting in a helium atmosphere. The alloys, weighing approximately 8 g, were sealed in evacuated quartz tubes and homogenized at 1030°C for 5 days. This isothermal heat treatment was terminated by a water quench from the soaking temperature. Filings of the alloyed pellets were sealed in evacuated quartz bulbs and quenched from 1030°C into liquid argon. A 14.32 cm Debye Scherrer X-ray camera was used for the powder diffraction study. The copper radiation was filtered. X-ray diffraction data for the compound Ti3Sn are given in Table I. The data were indexed on the basis of a hexagonal lattice. Good agreement between observed and calculated values of the square of the reciprocal interplanar spacings was obtained with the following expression: (1/d)2 = 0.03810 (h2 + hk + k2) + 0.04410 (l2) Unit cell parameters were calculated by the method of least squares from the reflections (20.3), (22.2), (40.1), and (42.1); ao = 5.916 & 0.004A, co = 4.764 ± 0.004A, and co/ao = 0.805. The relatively small size of the unit cell allowed the unambiguous indexing of most of the reflections from planes of large spacing. An inspection of the assigned indices (Table I) reveals the absence of (hk.l) reflections when 1 2n. A systematic absence of this type leads to the space group C 6/mmc or one of its subgroups. Assuming, for a first approximation, a linear increase in the density of titanium with the addition of tin, it follows that there are two stoichiometric molecules of Ti3Sn per unit cell. The density calculated from X-ray measurements is 5.194 g cm-&apos;. At this point it became clear that Ti3Sn might be isomorphous with Mg3Cd. The 6 Ti and 2 Sn atoms were placed in the following positions of space group D4 6h, C 6/mmc: 6Tiin (h): X 2X 1/4; 22;; 1/4;Xx 1/4;x2x3/4; 2x x 3/4; x x 4; with x = 516 2 Sn in (c): 1/3 2/3 1/4; 2/3 1/3 3/4.

Jan 1, 1953

By Charles R. Keyes

PAGE I. Introductory............ 140 II. Location and History...........140 III. Surface-Relief of the District....... 141 IV. General GeoloGic Features........ 142 1. Main Relationships and Map....... 142 2. Résumé of Geologic History..143 V. Geologic Formations Represented...144 1. Broader Considerations......... 144 2. Geologic Section.......... 145 3. Nomenclature.......... 146 4. El Pasan Limestones..146 5. Santa Rita Limestone.... 146 6. Silver Shales........... 147 7. Bella Shales........... 147 8. Berenda Limestone..147 9. Grande Limestone... 148 10. Lake Valley Limestone........ 148 11. Sierra Limestone.......... 149 VI. Unconformities........... 149 VII. Geologic Structure.......... 150 1. Main Characteristics......... 150 2. Folding........... 1.50 3. Faultings........... 150 4. Relations of the Eruptives...153 VIII. Geologic Relations OF the Ore-Bodies...... 154 1. Governing Factom......... 154 2. Position.......... 154 3. Relations to Foldings...155 4. Relations to Lines of Dislocation... 15.5 5. Relations to Present Surface.Relief..156 6. Relations to Eruptive Rocks...157 7. Relations to Lithologic Nature of the Rocks.... 158 IX. MINERALOGIC CHARACTER OF THE ORES...... 158 X. Origin of the Ore.Deposits..159 1. General Statement......... 159 2. Original Source of the 0re.Materials...160 3. Contact-Metamorphism of the Region... 161 4. Process of 0re.Concentration..162 5. Lowering of Ground-Water Level..162 6. Formation of Cerargyritic Ores...163 XI. Recapitulation........... 168

Jan 1, 1909

By S. Edward Drummond, Charles D. Haynes, Stephen H. Stow

This paper is a preliminary report on the occurrence and distribution of economically interesting heavy minerals (kyanite, sillimanite, staurolite, zircon, monazite, ilmenite, leucoxene, rutile) in sands from the sea floor surface of the offshore area, Alabama-Mississippi. Weight percent of heavies derived from the +60 portion of 97 samples is contoured in [Fig. 1]. Five hundred grains from 42 of the heavy mineral separates were identified and sized microscopically; the data were converted to weight percent for each mineral species and are summarized in [Table 1]. Heavy Mineral Distribution In the Gulf, there is a general westward decrease [(Fig. 1)] in maximum abundance of heavies from 2.4% north of Sand Island at the mouth of Mobile Bay to slightly over 1.0% south of Petit Bois Island and a corresponding decrease in the Mississippi Sound from 1.4%, north of Dauphin Island to slightly over 0.25% north of Horn Island. Average concentrations of heavies for different areas are found in Table 1. There is westerly longshore transport in this area; the interaction of the longshore current with discharge from Mobile Bay and disruptions of the current by Sand Island, possibly aided by a shoaling effect, appear to be the cause of the preferential deposition and concentration of heavies (2.4%) north of Sand Island in 10 to 14 ft of water.

Jan 1, 1977

By M. G. Benz, J. F. Elliott

A. J. Goldak and J. Gordon Parr (U)iuersity of Alberta) —Margolin and Ence&apos;s paper reached us only a few days after we had submitted a paper on the structure of Ti2Cu to the AIME. Here, however, we only wish to point out an error in the paper (page 321): "Karlsson has reported the crystal structure of the first intermediate phase occurring in the Ti-rich portion of the Ti-Cu system to be face-centered tetragonal." Karlsson actually reported the structure of Ti3Cu (i.e., "the first intermediate phase") to be primitive tetragonal with four atoms per lattice point: Cu at 0, 0, 0; and Ti at 1/2, 1/2, 0; 0, 1/2, 1/2; and 1/2, 0, 1/2. Thus, Karlsson suggests a primitive lattice with an ordered arrangement of atoms located at corners and face-centers: Ence and Margolin suggest a random body-centered tetragonal structure—-with which our results agree. E. Ence and H. Margolin (authors&apos; reply)— We do not agree that Karlsson has not reported the structure of Ti3Cu as face-centered tetragonal. The fact that Cu atoms are located at the corners and titanium at the face-centers does not indicate that the lattice is not face-centered. We are pleased that the discussers&apos; results agree with our own.

Jan 1, 1962

By Frederick Laist

The ores received at the Washoe Smelter come almost entirely from the mines in Butte and contain the following minerals : Chalcocite, Cu2S; covellite, CuS; chalcopyrite, CuFeS2, (trace); bornite, Cu3FeS3; enargite, Cu3AsS4; malachite, Cu2CO4 + H2O (trace); pyrite, FeS2; sphalerite, ZnS; rhodo-chrosite, MnCO3, (less than 1 per cent.); rhodonite, MnSiO3, (less than I per cent.). The country-rock of Butte is of the granite family and is a quartz-monzonite containing a little less silica than typical granite. It is made up of the following rock-minerals in approximately the proportions indicated: Minerals. Composition. Per Cent. Quartz SiO2 20 Andesine 1/2 NaAlSi3O8; 4 CaAI2Si2O8 42 Orthoclase KA1Si308 23 Hornblende 1/2 Ca(MgFe)3Si4O12; & (MgFe)2(AlFe)4Si2O12 6 Biotite (HK)2(MgFe)2A12Si3O12 9 Titanite CaTiSiO5 0.1 Apatite (CaF)Ca4(PO4)3 0.05 Magnetite (FeO)(Fe2O3 0.15 Pyrite FeS2 0.02 99.32 The main country-rock (quartz-monzonite) is cut by dikes of aplite, a granite having the following composition: Quartz, 30; andesine, 20; orthoclase, 45; ferro-rnagnesian minerals, 3; pyrite, 0.1; total, 98.1 per cent. Closely associated with the copper-deposits are dikes and bodies of " Modoe" porphyry, technically known as quartz-

Jan 1, 1913

By Luther Wagoner

Having given in a former paper1 the results of assays of sea-water, bay-mud, dredgings from San Francisco bay, etc., and believing it might be interesting to extend the work to include some deep-sea dredgings, I procured from the Smithsonian Institution six samples taken by the U. S. steamer Albatross, and marked as follows: Depth in No. station. Locality. Latitude. Longitude. Fathoms. 1. 2103. Off Delaware bay. 38&apos; 47&apos; 20" N., 72o 37&apos; W., 1,091. 2. 2265 to Between Chesapeake 35° 37&apos; N., 74O to 75O W., 49 to 70. 2297. bay and Hatteras. 3. 2420. Off Chesapeake bay. 37&apos; 03&apos; 20" N., 74O 31&apos; 40" W., 104. 4. 2528. East of Georges 41° 47&apos; N., 65o 37&apos; 30" W., 677. bank. 5. 2572. SE. of Georges bank. 40° 29&apos; N., 66O 041 W., 1,769. 6. 2681 South of Nantucket. 39&apos; 43&apos; N., 70&apos; 29&apos; W., 990. The above samples were assayed by the cyanide-method, described in my former paper (p. 807), about 30 g. of sample being used, and the following results were obtained: Value in Milligrams Per Metric Ton. No. Station. Gold. Silver. 1. 2103. 145 1,014 2. 2265 to 2297. 44 304 3. 2420. 15 353 4. 2628. 267 1,963 5. 2572. 125 377 6. 2681. 66 414 No. 4, Station 2528, consisting of red clay and volcanic ash, mas re-assayed ; 35 g. was roasted at a low heat for one hour and weighed 34.05 g. after roasting; the color was changed to a deep brick-red; and when assayed by the cyanide-method

Jan 1, 1908

By R. F. Hehemann, D. J. Cometto, G. L. Houze

The w transformation in the Zr-Nb system was studied using X-ray diffraction, dilatometric, re-sistornetric, hardness, and metallographic techniques. w forms in a diffusionless, completely reaersible manner on quenching and in a diffusion-controlled manner- on aging. The temperature at which w begins to form on quenching was determined as a Junction of composition and was found to decrease with increasing solute content. w formed bv aging establishes a metastable equilibrium with an enriched ß phase. The ß/w + ß transus has been determined for this metastable equilibrium and employed to rationalize retrogression and reversion phenomena observed in these alloys. The decomposition mechanism is discussed in terms of a gradual or continuous transformation from ß to the w state. BETA- stabilizing alloying elements lower the MS temperature of the martensitic bcc (ß) to hcp (a&apos;) transformation in zirconium and titanium alloys. In certain titanium alloys, a lower symmetry modification of the martensitic structure, termed (a"), also has been reported.1,2 These martensitic transformations are suppressed when the amount of the ß-stabilizing element exceeds a critical level. However, the high-temperature ß phase cannot be quenched to room temperature without change. At alloy contents just above the critical level, |ß trans-forms to the w phase when cooled rapidly.3-6 The amount of w in quenched alloys is reduced by increasing alloy content, and this phase virtually disappears above a critical composition.5 In addition to the transformation during cooling, w also can be formed by aging ß at temperatures below approximately 500°C, and significant alloy enrichment of retained 13 accompanies the isothermal transformation.1-8 The structure of LC is closely related to that of the ß from which it forms.9-15 The bcc (ß) lattice can be generated using a hexagonal cell with three atoms located at (000) and ±(2/3, 1/3, 1/3). This cell has an axial ratio of 0.612 and is oriented with respect to the cubic cell such that (0001)H (111)C and [1120]H [101]C. Consequently, there are four possible orientations of the hexagonal cell, associated with the four (111) planes of the bee lattice. Formally w can be obtained from 0 by allowing the two atoms at the ±(2/3, 1/3, 1/3) positions to approach the coordinates ±(2/3, 1/3, 1/2) and there are four equally probable orientations of w for each 0 grain. In titanium alloys w retains the cubic axial ratio of 0.612" and hence also can be indexed as triply cubic, but this is not the case for aged Zr-Nb alloys where w is clearly hexagonal with an axial ratio of 0.622." The lattice parameters and atomic positions of w depend on thermal history and alloy content. The atomic positions (000), ±(2/3, 1/3, 1/2) provide reasonable agreement between calculated and observed diffracted intensities for w in the fully aged condition.10,14 In the quenched condition, on the other hand, the atoms appear to be displaced from the central plane12,13,15 and assume positions ±(2/3, 1/3, Z = 0.42-0.48) rather than ±(2/3, 1/3, 1/2). This results in a structure with trigonal rather than hexagonal symmetry. The readily detectable parameter and axial-ratio changes of w in Zr-Nb alloys make this system especially attractive for studying the structural changes that occur in the formation and aging of w. Particular attention in this investigation has been directed to the relationship between the structure of w in the quenched and aged conditions, and to certain aspects of the reaction kinetics. MATERIALS AND PROCEDURE Zr-5, 12, 17.5, and 25 pct Nb alloys were prepared by a double arc-melting practice, encased in stainless-steel cans and hot-rolled to 1/8-in.-thick sheet.* Charged weights have been employed for the niobium contents and interstitial analyses are reported in Table I. Dilatometric, X-ray diffraction (filtered CuK, and MoK, radiation), metallographic, and hardness techniques have been employed to follow the transformations during isothermal and quench-aging heat treatments. In quenched specimens, the electrical resistivity also was studied. Betatizing was conducted for 1 hr at 900°C. With the exception of the isothermal dilatometric studies, samples were

Jan 1, 1965

By R. M. N. Pelloux

This study of aluminum-copper alloys had two aims: 1) To determine the effect of the amount and distribution of a second phase, CuAl2, on the creep-rupture strength, ductility, and fracture characteristics of the alloys. The work of Gemmell and grant&apos; on single-phase aluminum-copper alloys provided a basis for the present study. 2) To attempt to provide a relation between the microstructure and strength of two-phase alloys deformed at comparatively high temperatures (greater than 0.45 T,). The creep behavior of the two-phase magnesium alloys Mg;Ce and Mg-A1, has been treated by Roberts. 9 In work reported by Sully and Hardy4 and by Underwood, Marsh, and Manning~ on A1-Cu two-phase alloys, and also in a portion of the work of Gemmell and grant,&apos; aging took place during the creep tests. &apos;In the present work, overaged aluminum-copper alloys were subjected to creep deformation at two temperatures, 500 and 700OF. The overaging treatments to produce the precipitate dispersions were performed prior to the test, at temperatures which were the same as the ultimate respective test temperatures. Hence, the present study is concerned with the creep behavior of stable (in contrast to "underaged") two-phase A1-Cu alloys, i.e., alloys in which no depletion of the solid-solution matrix occurred during: creep. MATERIALS AND PROCEDURE A 2 and a 3 pct Cu alloy, supplied by Alcoa, were studied; Table I shows the compositions. The grain size of the specimens, 0.9 to 1.0 mm, was achieved by annealing the machined test bars for 2 hr at 1000°F, followed by furnace-cooling to 900°F, and homogenizing for 4 hr. Both compositions are in the single-phase condition at 900°F. Two types of overaged dispersions, termed "over-aged I" and "overaged 11" were prepared after the grain size and the homogenization anneals. The overaged I alloys were prepared by quenching to room temperature after homogenization, aging at either 500&apos; or 700°F for 72 hr, and air-cooling to room temperature. The overaged I1 alloys were prepared by furnace-cooling after homogenization, to either 500&apos; or 700°F, and holding at the necessary temperature for 72 hr. The times for furnace-cooling from 900°F to 700° and 500°F were, respectively, about 2 and 3.5 hr. The structures of the A1-2 pct Cu alloys are shown in Fig. 1 (overaged I) and in Fig. 2 (overaged 11). A comparison of Figs. 1 and 2 shows that in the overaged I alloys the precipitate particles along the grain boundaries are much more closely spaced and the grain boundaries are straighter than they are in the overaged I1 alloys. Further, the particle size and spacing in the grains are smaller than in the overaged I1 alloys. Microstructures of the A1-3 pct Cu alloys have not been shown; the structures of these alloys differed from those of the A1-2 pct Cu alloys only in that the distribution density of the particles was greater. The creep specimens had a gage section 1 in. long with a diameter of 0.155 to 0.195 in. Before testing, specimens were electropolished in a solution of 100 cc glacial acetic acid, and 30 cc of 60 pct perchloric acid, at 40&apos; to 50°F, at 24 v. The specimens were kept refrigerated prior to testing to avoid precipitation at room temperature. Constant stress creep tests were conducted; the load was applied 75 min after heating of the specimens to test temperature had begun. EXPERIMENTAL RESULTS Creep-Rupture—Fig. 3 shows the log stress-log rupture life plotfor the overaged alloys studied, and also for the underaged A1-2 pct Cu alloy.&apos; At 700°F, the stress-rupture life relationship is nearly independent of both the amount of precipitate (i.e., composition) and of the type of overaging treatment (i.e., precipitate dispersion). At 500°F it is apparent that the increase in rupture life that was ex-

Jan 1, 1960

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The technique of unidirectional solidification has been applied to the A1-AI3Ni and A1-CuAl2 ezltectic alloy systems; the controlled microstructure of A1-A3Ni consists of parallel A13Ni whiskers emhedded in an aluminum matrix while the Al-CuAl2, system solidifies as parallel alternate lamellae of aluminm and CuAl2. Mechanical tests (tension and flexure) have shown that the particle-matrix interface bond formed during unidirectional solidification allowes for efficient load transfer from the matrix to the reinforcing phase. Strength and fracture characterstics of the alloys were studied as a function of phase orientation; the tensile strength of controlled Al-Al3Ni samples was 43,000 psi (three times greater than that of as-cast specime~s). The strength of the Al-CIA2, cutectic was studied as a function of lamellae-flexure stress-axis orientation using a microbend apparatus. A twofold increase in outer fiber stress was observed as the lamellae were rotated from a position of no reinforcing (perpendicular to the stress axis) to one of maximum reinforcing (parallel to the stress axis), The brittle reinforcing constituent in each alloy (A13Ni and CuAl2) was observed to he the nucleating phase for fracture. It is to be concluded from this investigation that unidirectionally solidified eutectic alloys have a potential use as reinforcing coniposite) materials. In a recent review article, Chadwick1 has described the work of many investigators in the area of controlled solidification of binary eutectic alloys. Thus far, more than twenty eutectic alloys have been unidirectionally solidified to produce structures consisting of two phases in the form of alternating lamellae or as whiskers embedded within a continuous matrix; in either case, the phases are aligned parallel to the growth direction. In particular, Kraft and Albright2 have shown that the Al-CuA1, eutectic alloy exhibits a lamellar microstruc- ture as a result of unidirectional solidification while Lemkey, Hertzberg, and Ford3 have studied the A13Ni whisker-aluminum matrix morphology in the A1-A13Ni system. Whether these alloys could exhibit reinforcing behavior would have to depend upon the strength and volume fraction of the reinforcing phase (AI3Ni and CuA12) and the nature of the bond between the reinforcing phase and the matrix. Hertzberg and Kraft4 have shown that the interface bond between chromium whiskers and a copper matrix in unidirectionally solidified Cu-Cr is particularly good while Lemkey and Kraft5 have reported chromium-whisker tensile strengths in excess of 1,000,000 psi. However, with the chromium volume fraction being less than 2 pct, no reinforcing behavior was displayed by the Cu-Cr alloy.6 In view of the encouraging results concerning the good interfacial bond and high strength of the reinforcing phase in the Cu-Cr system and preliminary mechanical test data reported by Lemkey et al.3 for the A1-A13Ni system, the A1-CuA1, and A1-A13Ni eutectic alloys containing 50 and 10 vol pct, respectively, of the reinforcing phase give promise of possessing mechanical reinforcing behavior. Based on this premise, the objective of the investigation was to study the strength and fracture behavior exhibited by these anisotropic microstructures. EXPERIMENTAL PROCEDURE Controlled Solidification Procedure. An extensive description of the technique of unidirectional solidification has been presented elsewhere.&apos; However, the pertinent details for each eutectic system studied are discussed below. Al-A13Ni System. Several master heats of this alloy were prepared by vacuum-induction melting in an A12O3crucible and casting in SiO2 mold or by induction melting in alumina crucibles under argon. The initial heats were prepared from 99.99 pct A1 and 99.99+ pct Ni, while later heats used 99.999+ pct A1 and 99.99+ pct Ni. Specimens of these master heats were unidirectionally solidified using induction and resistance heating sources and argon atmospheres at growth rates from 1.1 to 28.7 cm per hr. The thermal gradients in the liquid were controlled in the range of 26" to 36°C per cm for these runs. Al-CuA12 System. The master heat and controlled

Jan 1, 1965

By Leon O. Hart

The nickel-chromium alloys of importance are those containing iron and those free from iron. The most important alloys containing iron, with regard to high tonnage, are the nickel-chromium steels. Straight nickel steel was introduced about the year 1889, but it was not until 1895, when it was found that the addition of chromium greatly increased the strength and resistance to shock, that nickel-chromium steels came into use. The three types of nickel-chromium steels developed at this time were: Type 1, containing 3.,50 per cent. nickel and 1.50 per cent. chromium; type 2, containing 2.00 per cent. nickel and 1.00 per cent. chromium; and type 3, containing 1.50 per cent. nickel and 0.50 per cent. chromium.

Jan 1, 1921