Search Documents

By D. R. Dollnar

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2002

By Guan Jichang

An abandened breakwater, located at the rear of No. 2 berth in Dongdu Port area of Xiamen City, was not cleaned thoroughly when the backfilling of sand started. The uncleaned stone layer was about 2 to 3 meters deep, with the average piece of stone weighing about 1 to 3 kN. A large grain storing house, 220X 60m2 in area, was designed and built at the above mentioned complicated site. The foundation of the grain house are made up of the cast-in-situ piles. It is well known that it is difficult for the submarine engineering drill to go down through such large-sized stones. Having com-pared the various plans, a final decision has been made which involves explosions with small amounts of charge plus cone bit in the enlarging of the size of the pores. Such a method has successfully prevented the pores from slumping and made it possible to fulfill the project without any difficulties. This paper also introduces the ways in effectively dealing with each individual stone.

Jan 1, 1991

By W. Bullen

A hypothetical economic model has been developed for diamond projects in the Canadian Arctic using data from recent exploration and mining projects. The model reflects economic conditions applicable to the diamond mining industry in the Canadian Arctic at the present time. The economic model captures pre-production expenditures, production data, and post-production costs. Before- and after-tax cash flows are derived from the data along with the relevant economic criteria. From the corporate perspective, the model provides guidance concerning the minimum size and/or in situ value per tonne requirements of targets being sought in order to ensure economic success and predict exploration and development expenditures. From the government perspective, the model provides an indication of income and mining tax revenues that can be expected from a particular diamond project. The model shows, on average, diamond projects in the Canadian Arctic are expensive to explore for and develop, but are economically robust under the present conditions. They generate great economic return for mining companies and significant amounts of tax revenue for governments. The fact that diamonds can be transported directly from the minesite by air makes them particularly attractive targets for mining companies that operate in the Canadian Arctic.

Jan 1, 2006

By Jocelyn Bouchard, Claude Bazin, Sami Makni, Rolando Quispe

"Finely disseminated minerals in ores require intensive size reduction to achieve sufficient liberation for the subsequent concentration process. The use of small grinding media in conventional ball mills as a replacement for the usual 2.5 to 3.8 cm balls (1.0 to 1.5 in) produces a finer size distribution at a lower power drawn by the mill motor. However, the conditions ensuring a successful application of using small media for fine grinding are still not fully understood and some plants faced issues to keep the newly introduced steel charge inside the mill during industrial trials. The retention conditions of small media are investigated in this paper using a continuously operated 40 x 40 cm laboratory grinding mill. The tests assess the effect of the steel charge level, the slurry solids concentration and the feed rate on the rate of ejection of the grinding media. The dominant variable is found to be the filling of the mill with the grinding media, followed by the mill feed rate. Results show that increasing the slurry solids concentration within a grinding mill may be favorable for the retention of the media inside the mill.IntroductionProcessing of complex ores often requires the use of fine grinding to liberate finely disseminated minerals. Grinding requirements for a P80 of less than 0.02 mm are not uncommon, and different grinding mills are available for such application (Leonida, 2014; Pease et al., 2006; Davey, 2006; Orford et al., 2006; Nesset et al., 2006). Even conventional horizontal ball mills charged with of 2.5 cm or larger grinding media can be used for fine grinding. However, simulation (Orford and al., 2006) and plant observations (Alves and L-Bouchet, 2005; Brisette, 2010; Brisette and Roman, 2012) demonstrated the advantages of using smaller grinding media in terms of size reduction and energy consumption."

Jan 1, 2015

By Y. X. Zhao

This paper briefly describes the characteristics and induced factors of coal mining bumps based on the investigation of recent bumps accidents occurred in China. According to the theory of non-equilibrium thermodynamic and dissipate structure, the process of strain energy accumulation and dissipation in the ?Coal-Surrounding Rock? system (CSRS) is discussed during the preparation of coal bumps. In addition, a series of experiments are conducted to analyze the relationship between bump-prone property and micro-structural characteristics of coal. The process of coal bumps induced by propagation of fractures and deterioration of coal mass properties are also analyzed systematically.

May 1, 2009

By Congcong Chen, Bo Ma

When assessing the safety of a tailings dam, the constant weight method (CWM) is one of the most commonly used methods. However, when the evaluation indicator value suggests serious defects, the evaluation value is often inconsistent with the actual situation. To address this issue, the variable weight method (VWM) is introduced to assess the safety of the tailings dam. Initially, a three-layer indicator system for dam failure safety assessment is built, and individual indicator values are divided into four grades. Then, an appropriate state variable weight function is constructed and relevant parameters are determined. Finally, a case study is illustrated to verify the effectiveness of the model. The assessment results of the VWM more closely represent the actual situation than that of the CWM, which is more helpful for decision makers and technicians to take scientific and reasonable precautionary measures, thereby improving the safety management of the tailings pond.

Oct 8, 2022

By Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-proof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges.

Jan 1, 1974

By D. Laguitton, D. Hodouin, V. K. Gupta, R. Spring

"The CANMET SPOC project aims at inducing progress in process evaluation and optimization by developing user oriented software based on state-of-the-art theory. The present work is the result of a joint effort by CANMET, Noranda Mines and Université Laval to develop two computer packages: one (RTD) to calculate the residence time distribution that best describes the material transport through the mill, the other (FINDBS) to estimate the rate of breakage and distribution function of the population balance model in a ball mill. The RTD package can handle data from various experimental methods (impulse or complex tracer feed, with or without recycling, etc...). The FINDBS package provides options for the functional description oj both model parameters Band S. The full detail of the methods and programs appears in a users guide. The program capabilities and several sample runs are presented.IntroductionSimulation of mineral dressing operations by computer has been largely contained within academic and research circles and has not yet gained a status of routine practice in the ore and coal industries. It is however a matter of time before process simulators are available on every process engineer's desk to assist process optimization tasks, flowsheet design and professional training. The CANMET SPOC project (Simulated Processing of Ore and Coal) was initiated in 1980 to assist the Canadian industry in integrating computer-based methodology for process evaluation and optimization(1). Software development, documentation and transfer is one of the main priorities of the project which will mature in 1985 by releasing a complete package of manuals and programs covering sampling, material balance computation, unit modelling, flowsheet simulation and optimization . This paper is a condensed description of a typical project element in its 1982-1983 state of development. The required methodology for ball-mill modelling and simulation was consolidated an d merged to other project elements during a joint study under contract financed by CANMET and Noranda Mines Ltd . The first part of the study dealt with documenting experimental methods and software for ball-mill computer simulation. Université Laval GRAAIM (Goupe de Recherche en Automatistion Appliquée à l'Industrie Minérale) acted as sub-contractor for this part of the study(16,17). A second part dealt with applying the model calibration techniques to a large industrial data base and is reported elsewhere(2,18,19)."

Jan 1, 1984

By L Abrahamsson

This paper describes results from a gender study for a new mine in Pajala, a small community in northern Sweden. Using a gender perspective, the study examines migration, education, local culture, the labour market, and work organisation as problems and opportunities in the regional context for the planned mine. The most obvious ‘gender issue’ for the Swedish mining industry is the very low percentage of employed women, which is even lower among mining workers. To recruit the best people, a company actively needs to attract both women and men; however, the mining companies find it difficult to recruit women as cultural, labour market and educational traditions as well as the mining companies’ own cultures often make it difficult for women to find work in the mining industry.The Torneå river valley, the region surrounding Pajala, has a gender-segregated labour market and gender-stereotyped culture and few young women live in this traditional and oldish region. Many young people leave the region and this is especially true for women. Compared to the rest of Sweden, there is a low educational level, especially among the men. In the mining companies, as in many other male homosocial workplaces, the workplace culture has strong connections to a certain type of traditional masculinity (laddishness, a kind of ‘macho-style’) and for a long time this has excluded women. ‘Gender’, however, is not only a question of recruiting women to a male-dominated industry. An organisation that discriminates according to gender can become inflexible, hindering communication, learning, innovations and change processes. In mining companies, this can manifest itself in hesitant attitudes among the miners about safety as well as organisational and technological development.This study found that companies establishing a presence in this region should develop a strategy for how to deal with and manage the risks and opportunities in the surrounding society (the regional culture) as well as inside the company (the mining culture). This need to be strategic will also be required of future mining companies as they will face higher demands on safety, gender equality, and technology to become modern, efficient and lean organisations.

Nov 22, 2011

By Rixon K. L

Hargraves (1983) has reviewed the phenomenon of instantaneous outbursts of coal and gas with special attention to Australian occurrences. The purpose of this discussion is to highlight some problems and omissions in his review that reflect particularly on the authors' structural geological investigations of outburst-prone coal seams.It is surprising to find that much of the authors' reported work has either been glossed over or the results distorted by Hargraves (1983) and it is, therefore, important to clarify the contribution that structural analysis of coal seams can make.For many years it has been known that faults provided preferred loci for gas outbursts (for example, Briggs 1920-21) but the roie that faults played in outburstprone seams was unclear. The present authors reviewed the association of faults and outbursts drawing upon local investigations and the world-wide literature (Shepherd et aI., 1981), and discussed some wideranging aspects that result from the high coincidence of faults and outburst sites. Without repeating large segments of this article the authors will discuss four aspects of coal seam faulting and fracturing.

Jan 1, 1983

By Hyung-woo Kim, Kiyoung Sung, Sup Hong, Jung-Yeul Jung

Many concepts for the commercial production of deep-seabed manganese nodules have been studied since the 1970s. However, the bearing capacity of the deep seabed is not strong because it is composed of fine particles with high moisture content. So it is impossible to carry manganese nodules in the collection system. Therefore, the validity of continuous mining by riser pipe from the seabed to the vessel is highly appreciated. A continuous mining system is composed of mining vessel, lifting pipe, buffer system, transport tube (flexible pipe), and self-propelled mining robot. A conceptual diagram of this system is shown in Fig. 1(a). Korea Research Institute of Ships and Ocean Engineering (KRISO) developed a deep-seabed self-propelled mining robot called "MineRo" to collect manganese nodules in 2012 (as shown in Fig. 1(b)). In 2013, real sea experiments at around 1380 m depth were carried out to evaluate the collecting and driving performance of MineRo. However, we found that the roller in MineRo did not work well at times. To elucidate the problem, we analyzed the rheological characteristics between the bushing and drive shaft under deep-water conditions.

Sep 1, 2014

By André Desbiens, Jocelyn Bouchard, René del Villar

"The metallurgical performance of the column flotation process is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a model-based automatic control strategy using froth depth and bias measurements obtained from virtual sensors developed at Laval University. Preliminary pilot plant results on two-phase (water– air) and three-phase system (water – minerals – air) will be presented and eventual industrial implementation of such a strategy as well as the possibility of achieving effective real-time optimization from bias and froth depth measurements will also be discussed.INTRODUCTIONFlotation columns have been widely studied and used in mineral processing for about twenty years. Although a great deal of work has been accomplished to understand the influence of different variables such as froth depth (H), bubble surface area flux (Sb) and bias (Jb) on the metallurgical performance, the measurement of some of these variables is still difficult to be performed – except at the laboratory level – because in most cases, no commercial device yet exists.As a result of this, it is almost impossible to achieve neither efficient control nor optimization of the process at the industrial level, even in open-loop operation. This paper aims at presenting a simple control strategy of froth depth and bias. Description of the sensors used to achieved measurements, preliminary pilot plant results for froth depth control, eventual industrial applications and possibilities for process optimization are also treated."

Jan 1, 2003

By P Staples, G Lane, S Morrell

The design of semi-autogenous grinding (SAG) mill based comminution circuits for the treatment of competent ores, similar to those at Geita and Boddington, involves the same process of sample selection, test work, data analysis and data modelling/interpretation as that used for 'average' competency ores. However, over the past couple of years a number of issues have arisen that are common to the design of circuits for the comminution of 'highly' competent ores. The impact of these issues on project viability is generally more pronounced when treating hard ores than average to soft ores due to the greater impact on capital and operating costs. The issues encountered have included: standard test procedures have been modified; test equipment has worn or been damaged; different procedures yield different data and varying interpretation; and modelling and empirical calculations have been based on poor benchmarks, or used incorrectly in the case of JKSimMet, yielding misleading outcomes. The purpose of this paper is to present, discuss and clarify some of the issues associated with conducting test work and designing comminution circuits for the treatment of 'highly' competent ores in order to reduce thelevel of conflict arising from interpretation and application of test work data. Specifically, the issues associated with the bond crushing (impact) and rod work indices measurement, the various SAG mill specific energy tests, and the interpretation of the resulting data will be discussed in the context of case studies.

Jan 1, 2009

Test Work on High Throughput Diamond Tracer Recovery from Alluvial Recovery Tailings with a Containerised Optical Sorter Under Real Production Conditions Worldwide alluvial diamond deposits are traditionally processed with dense media separation and XRF sorters, hand picking or grease tables. The test work conducted verifies the performance of an optical sorter detecting the transparency of particles for diamond recovery from the DMS concentrate, eg XRF-sorter and handpicking tailings. The containerised setup enables economically feasible, high throughput, semi-mobile setups to retreat recovery tailings from alluvial and also primary deposits. The test work has been conducted with quartz and glass particles, which are less transparent or comparably transparent, under realistic production conditions on a 600 mm belt machine with an installed electrical power of only 21 kW. The results show that 99 per cent recovery can be reached at a throughput of 10 t/h in the -8 + 2 mm fraction and at 22 t/h in the -25 + 8 mm fraction. At a throughput of 18 t/h a recovery of 88 per cent has been assessed. At a further escalation of the throughput, dust in the sorter container made sorting impossible in the coarse fraction and the recovery decreased significantly in the fine fraction. Analysis of the belt coverage indicates that higher throughputs of the coarse fraction can be fed onto the optical sorter if the dust extraction system is improved. The results are basis for the decision to conservatively feed 20 t/h of the coarse fraction and 17 t/h of the fine fraction in day to day production. The settings have been applied to sort alluvial recovery tailings in South Africa and will be applied to sort the recovery tailings of a primary deposit in Lesotho. The test work has shown that an optical sorter can be used to retreat recovery tailings with high throughputs. The compact setup of a screen and a 9 m standard container enables semi-mobile, temporary setups for small recovery tailings dumps and remote areas. In addition, sorting on transparency ensures the recovery of high value low-fluorescent diamonds.

Sep 13, 2010

The estimation of the shear stress distribution around an excavation is important to the design of the excavation since shear stresses can generate cracks, loosen grain boundaries or otherwise degrade the mechanical and physical properties of the rock and lead to stability problems. In this study, the distribution of shear stresses in a pillar were back-calculated from the deformation measurements made from the SPDV (Site and Preliminary Design Validation) area at the Waste Isolation Pilot Plant (WIPP) site. A plausible pattern of shear stress around an excavation has been suggested based on the Zero Strain Boundary (ZSB) calculation, computer simulation using FLAC, and back-calculation using measured deformation rates in the pillars.

Jan 1, 1998

By Tammy G. R. Portela

A comparative characterization of the dimensional and mechanical properties as well as structural aspects of two different types of fibers extracted from the leaves and petioles of the buriti palm tree was performed. A statistical analysis revealed that both types of fibers present a significant dispersion in length and equivalent diameter. However, the corresponding intervals of dimensional variation are sensibly different. The tensile properties showed that both types of fibers display a tendency of higher strength for smaller diameters. Moreover, the fibers extracted from the leaves depict a comparatively lower strength. By contrast, the fibers from the petiole present an average strength sufficiently high for the use as reinforcement of polymeric composites. The structural aspects of tensile-rupture fibers, characterized by scanning electron microscopy, showed marked distinction in the microstructure and fiber behavior of both types of investigated fibers. This could explain the differences in mechanical behavior

Jan 1, 2010

By Sanjeeva Latchireddi, Travis Orser

"Today’s high capacity semiautogenous grinding (SAG) mills expend vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. The energy efficiency of these high throughput grinding mills can be attributed to the field of breakage and slurry discharge system. The charge motion and breakage of particles inside the mill depends on the shell lifters design, while the discharge of ground particles is controlled by the grate and pulp lifters. The limitations imposed by poor grate and pulp lifter design become increasingly apparent with increasing size of ag/sag mills and their operation in closed circuit. The design of these mill components has been largely based on trial and error and hence varies considerably between manufacturers. This paper discusses the use of two state of the art design tools - Millsoft™ and FlowMod™. Millsoft™ is an effective tool to design the shell lifters and optimize charge motion, whereas FlowMod™ simulates the slurry discharge system to design grate and pulp lifters. The application of these simulators will be discussed using case studies of full scale mills.INTRODUCTIONMany large mining operations around the world have one or more semi-autogenous (SAG) mills doing bulk of the work in their size reduction operation. The SAG mill is usually followed by a ball mill to finish the size reduction prior to the concentration step. In the past when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the SAG mill operation. As a result mines have shifted their emphasis in optimization from ball mills to SAG mill"

Jan 1, 2005

By Carl Lee

CHICAGO in the last week of June fulfilled all its promises to the visiting engineers except one. This holds true with respect to the activities of the Regional Meeting of the A. I. M. E. in particular and of Engineers' Week in general. No one expected to find much of the beautiful in the outward aspects of the Fair-the Century of Progress Exposition, to be more formal; but they expected novelty, color, and startling lighting effects at night, and they were in no sense disappointed. It has been said that the architecture is a portent of the style of the buildings of the future; most who have seen the Fair hope that this forecast will prove inaccurate. As to the exhibits themselves, they are splendid. They are in keeping with the theme of the Exposition-a Century of Progress in science, in engineering, in the industries based upon them. No attempt will be made here even to suggest the exhibits that are most interesting. There are plenty for every one; and any member of the Institute who has the opportunity should by all means visit Chicago before the end of October.

Jan 1, 1933

By Mark P. Juzli

During the 1980s, a revolution has been taking place in industrial minerals marketing. Transportation deregulation and a handful of creative marketing and distribution managers have completely changed the rules for marketing many industrial minerals. Minerals are being transported much farther than in prior decades and at much less cost. Bulk and package terminals are becoming increasingly common as a means to take advantage of freight rate savings and to provide enhanced service to faraway customers. Water and rail transportation are being used increasingly to penetrate markets considered unreachable just a few years ago. No longer do the textbook rules of thumb for industrial minerals marketing apply. This author recalls three of those rules he was taught in mineral economics graduate school in the 1970s. As recorded in class notes: • construction aggregates are seldom shipped more than 32 km (20 miles) from the quarry; • cement is sold within 240 km (150 miles) of the mill; and • industrial sand is sold regionally - it is freight constrained to a market radius of no more than 320 to 400 km (200 to 250 miles) from the plant. And yet, the author looks up in 1989 and observes overland movements of aggregates of many hundred miles, overland movements of cement and industrial sand of 1600 km (1000 miles) or more, and water movements of both aggregates and cement into the United States from sources halfway around the world. Truly, industrial minerals are in the midst of a marketing revolution. The companies that have led this revolution have enjoyed considerable financial success in the 1980s. They have enhanced their profitability by increasing market share, capacity utilization, and average selling prices by taking product to remote markets where premium prices are available. They have consistently outperformed their competition, many of whom remain unaware that the marketing revolution going on around them is actually a transportation/distribution revolution. The successful industrial minerals company of the next 10 to 15 years must participate in the transportation revolution as it continues to evolve. Additional human and capital resources must be committed to maximize the effectiveness of a company's transportation and

Jan 1, 1989

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company's Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963