Search Documents

By T. R. Wildeman

"At the Big Five wetland, which was built to treat drainage from a metal mine, encouraging results have attributed to sulfate reduction. Cu and Zn were reduced to below detection limits of 0.50 mg/L, Fe was reduced by at least 90% to below 3 mg/L, and the pH was raised from below 3 to above 6. The study showed that treatment was primarily through microbial processes within the substrate and that plants were not needed to insure success.Constructed wetlands can be taken through design and proofing stages, and into operations scale in a meaningful time frame for on-line acid drainage remediation. In staged design, laboratory experiments are initiated to determine reasonable substrate materials for remediation of a particular drainage. When a reasonable substrate is found, bench scale experiments are initiated as the next stage in the design. In these studies, removal efficiency, permeability, and flow are analyzed to identify candidate substrate which will support sulfate reduction and be hydraulically reasonable. Using this design method at one site, an acid drainage of pH 2.5 was raised to a pH of above 7. Total heavy metal concentrations in this drainage exceeded 900 mg/L. In the pilot constructed wetland Cu, Zn, and Fe were reduced by 99%.Determining how well these anaerobic cells operate in the winter is done at the pilot plant site in Idaho Springs, CO. It's been found that over the last four winters, those cells that emphasize anaerobic removal within the substrate have operated continuously and effectively the year round. Winter operation is aided by the fact that the water temperature of the acid drainage is always between 14 and 16° C, and the cell can be readily insulated from the cold. Activity of the sulfate reducing bacteria may decrease during the winter. However, it appears that organic complexation of metals helps to maintain low concentrations of metals in the effluent."

Jan 1, 1992

By Robert A. Cortese, Henry E. Perlee

Coal dust and float coal dust, produced during normal mining operations, in underground coal mines, are carried from the point of origin downstream by the ventilating air, where it deposits on the surfaces of the mine entry. In an explosion, this dust is lifted from the surfaces by the aerodynamic disturbances and, if of sufficient quantity, can continue to propagate the explosion. To prevent the surface coal dust from contributing, it must be inerted, typically by spreading pulverized limestone, i.e., rock dust, over the coal dust surface. To facilitate the dusting operation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory(PRL), developed an automated system that continuously monitors the accumulation of coal dust. This system could activate a rock-dusting machine that disperses rock dust into the ventilation air when dangerous deposits accumulate and deactivate the machine when sufficient inert has been deposited on top of the coal dust. The system consists of a microprocessor-controlled optical float dust deposition meter. This device measures the light intensity reflected from a deposited layer of dust. A standard cap lamp is used as a fixed-position light source. From the reflected light signal, the microprocessor determines the hazard level of the deposited layer and performs the appropriate action. Full-scale studies conducted in the Experimental Mine at PRL's Lake Lynn Laboratory, using alternating thin layers of rock dust and coal dust, successfully demonstrated the operation of the device. Based on the statistical data from these studies, a mathematical model was developed to predict long-term error in total rock dust content using this inerting procedure. Downwind dust dispersion was also examined to provide optimum placement of the dust sensors and to determine the need for better rock dust dispersion techniques.

Jan 5, 1998

By Robert H. Bedford

The Rogan-Mallery tin property is in the foothills on the south slope of the Tehachapi Mountains, Kern County, Calif. It was first visited by the senior author in August 1942, and exploration by means of trenching and diamond drilling began in May 1944 and was concluded in August of the same year. Cassiterite, associated with iron-rich gossan, occurs in a limestone roof pendant at places near or at its contact with the underlying granitic rocks. The cassiterite grain sizes range from 20 mesh to 150 mesh. Surface and diamond-drill samples showed tin ranging from traces up to 122.6 pounds per ton. Exploration by the Bureau of Mines included 2,100 cubic yards of trenching and the drilling of 11 diamond drill holes totaling 1,000 feet. Dana Hogan, president of the Rogan Petroleum Co. of Los Angeles, Calif.) brought these projects to the attention of the Bureau of Mines in July 1942, and the following month a Bureau engineer made a preliminary examination in company with Hillard Mallery, of 408 Ruby Street, Redondo Beach, Calif., the man who discovered them.

Jan 1, 1949

By Fulton Flick

THE micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents. are available for the development of such structures in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Archbutt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the, specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a con¬siderable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it is worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c.c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric-acid solution.

Jan 2, 1925

By R. L. Grayson

In 2010, MSHA began holding hearings on a new coal mine respirable dust rule, which proposes a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the ?hot spots? where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines? compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, seam height, and selected ?hot spot? counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications on the need for better dust control methods.

Jan 1, 2012

By John Wise

Significant movement to an existing slurry wall which serves as a retaining wall on 'O' Street in Southeast Washington, D.C. initiated the Department of Public Works for the District of Columbia to invite specialty contractors to propose a rehabilitation and stabilization for the failed slurry wall. Nicholson Construction Company proposed and was awarded a contract for the construction of an anchored precast lagging and soldier pile wall to be located approximately 4 feet in front of the existing structure with granular fill placed between the new and existing walls. Stabilization of the existing slurry wall also included drilling horizontal weep holes and demolishing the failed panels down to the existing ground surface. A new and improved drainage system was also constructed to increase the amount of water directed toward the existing storm sewer system running along 'O' Street. This paper provides a detailed account of these construction activities.

Jan 1, 2003

PRODUCTION of cesium, cesium salts, and rubidium salts in the United States declined somewhat from 1961 levels; rubidium production was virtually unchanged. Imports of pollucite declined because consumption was supplied partially out of inventory. Domestic Production.-About 50 tons of pollucite was reported mined at the Tin Mountain mine in the Black Hills of South Dakota. The Dow Chemical Co., Midland, Mich., MSA Research Corp., Callery, Pa., and Penn Rare Metals, Inc., Revere, Pa., produced a total of 159 pounds of cesium. Rubidium production remained essentially the same as in 1961. Shipments of the two metals by these companies and by American Potash & Chemical Corp., Trona, Calif., totaled 279 pounds. Production of cesium and rubidium salts by American Potash & Chemical Corp., Penn Rare Metals, Inc., and Rocky Mountain Research, Inc., Denver, Colo., declined substantially during 1962.

Jan 1, 1963

By Donelson A. Robertson

Includes a review of the state-of-the-art of explosives loading in the crushed stone and cement industries of South Florida and the development of a field test program for alternatives. Emphasis is on the loading of small diameter (2 1/4" or less) explosives. Test results ire evaluated for operational and economic feasibility. Details are described of an explosives loading method which involves placing cardboard tubes with external couplings through the hollow drill steel and then Loading explosives into the tube casings after the drill rig has moved off. This method eliminates the hazards peculiar to loading explosives Through the kelly bar. The alternative method can be performed by existing drill rigs with or without minor modification. With modification, improvement in yield per blasthole and/or primary crushing rate provides opportunity so offset some or all of the additional cost.

Jan 1, 1978

By Lynch A. J

A method has been developed for the prediction of the performance of multi-stage grinding-cyclone classification circuits of any degree of complexity on any ore for a wide range of operating conditions. The method involves the simulation of the circuit on a digital computer by means of. mathematical models of the individual units. At present, to establish the characteristics of the ore and the machines in mathematical terms, it is necessary to know the performance of a simple system on the ore for one known feed rate and feed sizing analysis.Further work on the separate identification of the terms defining the characteristics of the ore and the machines may permit the method to be applied directly to the data derived from small scale tests on ores.INTRODUCTIONThe cost of preparing metalliferous ores for concentration processes by, grinding and classification frequently represents a major portion of the cost of treating such ores, and it is necessary both from an economic and a metallurgical point of view that grinding and classification circuits should be operated at their optimum efficiency. It will be realized that the processes carried out in all units in such circuits behave according to physical laws and, if a mathematical representation of the laws applying to each unit could be derived, optimization of the overall process for any given conditions of feed or product may not be difficult.The physical processes in both tumbling mills and hydraulic classifiers are extremely complex and do not appear at present to be amenable to a rigorous mathematical analysis. However, empirical mathematical models of grinding units which have been presented previously (Callcottand Lynch, 1963; Lynch and Moore, 1963) may be used to discuss the operation of the grinding units in multi-stage circuits. Another type of model, which leads to a reasonable...

Jan 1, 1965

By Joseph F. Davies

To gain knowledge of the actual accident hazards present in Kentucky coal mines, reports of fatalities during 1931, 1932, and 1933 have been analyzed and the pertinent factors included in tables, accompanied by some discussion and recommendations for the reduction of accidents from particular causes. ACKNOWLEDGMENT This study was made possible through the cooperation of John F. Daniel, chief of the Kentucky Department of Mines, who made available department records, in addition to the monthly bulletine issued by his office reporting these fatalities.

Jan 1, 1934

By J. A. Singmaster

IT will perhaps be wise to define my terms in begin-ning to talk about my subject, especially so where the popular and commercial terminology are as con-fused as they are in the case of zinc. While our French friends know zinc by its true name, and we find Balzac, Daudet, and other literary celebrities using it correctly in their novels, it is quite the contrary in English, particularly here in America. The quotation of a definition for zinc recently appearing in one of our leading technical magazines, "zinc is the place where they wash the dishes," will emphasize the difference. Zinc suffered in the first place by becoming an article of commerce long after its alloys with copper were in common use under the name of brass. Then again, when the art of zinc coating iron and steel objects was commercialized, we called it galvanizing, which is really a meaningless term. The French and Germans use the obvious terms-zinguerie and verzinken-for the opera-tion. Since these two uses of zinc, brass making and galvanizing, have been by far the largest consumers of zinc, is it any wonder that the popular knowledge of zinc is as vague as it is? In fact, since the disappear-ance of the sheet of zinc along with the parlor stove, the zinc-lined bath tub and refrigerator, there has been little popular contact in this country with the undis-guised metal zinc. On the Continent, where zinc has been used for over a hundred years under its real name, particularly for roofing and building purposes, the situ-ation is quite different. It is quite refreshing to turn for a moment to the contrast offered by my friend, Dr. Merica's specialty, nickel. They put 2 or 3 per cent of it into steel, and we have nickel-steel, or a larger amount into an alloy, and we have nickel-silver. To be sure there is no silver there, but what need that matter, nickel is used in the alloy and is first in the name. They plate with nickel and call it nickel-plating, no galvanizing about that. And, finally, they take that noble coin which admits us daily to underground New York, composed of three parts of copper and one part nickel, and get away with nickel as its popular name.

Jan 6, 1927

By Jorj O. Osterberg

Until ten years ago, the largest load tests on drilled shafts (bored piles) were about 3,000 tons (27MN). These tests were made with kentledge (large weights, usually concrete blocks) stacked up as a reaction to the applied downward load of a hydraulic jack. In some cases, the jack load is resisted by a load frame held down by piles or anchors connected to the frame. When the test loads exceed 3,000 tons (27MN), these methods become cumbersome expensive and time consuming. The Osterberg (O-cell) test method does not require any reaction load. It has become the only cost effective method for static load testing of high capacity shafts. Over 650 load tests have been performed with this method, 86 of which were over 3,000 tons (27 MN) and 40 over 5,000 tons (44 MN), and the largest test load was 17,000 tons (150 MN). Tests have been made on sands below the water table, shafts ending in rock sockets, and cemented sands and gravels. Test results and details for selected load tests are discussed.

Jan 1, 2002

By J. Samir

The objective of this study is to simulate the isothermal filling up of moulds by a RTM process when adopting CV/FEM and VOF method and when also taking into account the presence of obstacles coupled to the effect of the thickness and reinforcement layers variation. The codes developed intended to ensure an optimal positioning of the injection points and of the vents and also to determine optimal injection pressures, in order to minimize the cycle times. These codes use a mesh generator proper to the team, allowing a discretization of the domain in triangular unstructured elements, with the possibility of a local refinement and inserts inclusion.

Jan 1, 2009

By M. Mustafa Kahraman, Sean Dessureault, W. Pratt Rogers

Most contemporary mines have considerable amounts of data. Structured and unstructured large data sets are colloquially named big data. Much of the data in mining operations come from a variety of systems, each with different databases and reporting environments. Standard technology deployments create a Bsilo-ification^ of data leading to poor system benefit. Through modern server monitoring and systematic approach, data utilization and value can quantifiably be measured. The Data Utilization and Value Index (DUVI) can quantify business intelligence best practices and user interaction. This study seeks to provide a data management tool to measure data utilization across the process of converting data into action.

By Steve Custer, Tim Kahl, Sue Parker

"The primary objective of the Barrick Goldstrike expert system is to achieve the desired liberation size for the autoclave circuit while maximizing throughput. In addition, when downstream limitations (autoclave circuit or others) restrict the milling circuit tonnage the expert system further improves grinding product size. Since its implementation, the expert system has provided expected throughput improvements while improving or maintaining circuit performance.Barrick Goldstrike and MinnovEX Technologies Inc. teamed up to install an expert system to control Line I and I1 of the autoclave grinding circuits. The dissimilar equipments of the two grinding circuits coupled to different production objectives, skepticism among operators, and the variability of the ore types processed in each line challenged the implementation.To ensure implementation success, Barrick Goldstrike dedicated four administrators full time to the project. The system administrators included two metallurgists, a process control engineer and a mill trainer. As usual, the control room operators were the experts who provided the operational logic for the foundation of the control system. The administrators and all eleven of the control room operators signed off on acceptance of the system. Current online utilization is 95%.INTRODUCTIONThe grinding circuit for Barrick Goldstrike’s autoclave process consists of two SAG Mill Ball Mill lines. Line 1 grinding circuit is comprised of a 22 by 8 foot, 2500 horsepower Allis Chalmers (AC) variable speed SAG mill, followed by a 12.5 by 14 foot, 1250 horsepower AC ball mill, and a 13.5 by 18 foot, 1800 horsepower Dominion ball mill in parallel. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1352 Nordberg Omnicone crusher (4.5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The ball mill circuit is closed with 6 Krebs super D20 cyclones. Line 2 grinding circuit is comprised of a 24 by 12 foot 4000 horsepower Fuller variable speed SAG mill followed by a 16.5 by 30.5 foot 5000 horsepower Fuller ball mill. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1560 Nordberg Omnicone crusher (5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The line 2 ball mill circuit is closed with 12 Krebs super D20 cyclones. The underground Meikle ore is typically fed through Line 1. Achieving the desired product size is critical for successful processing of Meikle ore. Open pit Betze ore is fed to Line 1 when Meikle ore is unavailable. Line 2 processes Betze ore exclusively. Throughput is maximized when processing Betze ore as the product size is less critical. The products of these two circuits are combined as feed to the autoclave circuit. The ore types and the autoclave circuit demands determine the required grinding circuit product size and maximum combined mill feed tonnage."

Jan 1, 2001

By W. J. Boone

The Bureau of Mines has programmed for publication a series of Reports of Investigations of studies it has undertaken on low-temperature phase equilibria of several helium-bearing natural gases. This report is the second of a series of papers of the same general title; it is anticipated that additional reports of this series will be published. The advent of a helium conservation program and the prospect of production of helium by private industry, make it especially desirable to publish these data. This report describes phase equilibria related to a natural gas that is processed for helium at the Bureau's Exell Helium Plant (located about 35 miles north of Amarillo, Tex.). Carbon dioxide and water in the gas were removed before making the study; hence the data obtained are representative of the gas stream immediately after similar preliminary treatment in the plant process. Phase equilibrium data were obtained for conditions from -50° to -275° F. and from 100 to 500 p.s.i.a. Analyses of samples were made as follows: For a given run at a selected temperature and pressure, samples of the vapor and liquid phases were analyzed by mass spectrometer, and an additional sample of the liquid phase was analyzed for helium by means of special apparatus (7). 4

Jan 1, 1962

By N. Barton, E. Quadros

This paper addresses the prediction of groutable joint apertures, grout penetration limitations, and possible grout take volumes per cubic metre of rock, as a result of 5 to 10 MPa pre-injection pressures ahead of tunnels. Joints are obviously opened more than in the preceding Lugeon tests, and many rock mass properties can apparently be improved if stable micro-cement based materials are used. Cet article concerne la prédiction des ouvertures des fractures injectables, les limites de pénétration du coulis et les volumes injectés par mètre cube, d’après les résultats des injections à l’avant tête des tunnels sous pressions de 5 à 10 MPa. Evidemment les joints s’ouvrent plus que dans les essais Lugeon précédents. Maintes propriétés du massif peuvent apparemment être améliorés si l’on emploi des coulis a base de micro-ciment stable. Die Publikation widmet sich der Prognose injizierbarer Kluftöffnungen, Grenzwerte für Injektionsreichweiten und erreichbarer Injektionsvolumen pro Kubikmeter injizierter Fels, durch die Anwendung von 5 bis 10 MPa Vorinjektionsdrücken vor der Tunnelfront.Die Klüfte werden offensichtlich weiter geöffnet als in den vorhergegangenen Lugeon Versuchen und mehrere Felsparameter können durch die Verwendung von stabilisierten Micro-Zement basierten Injektionsmaterialien verbessert werden.

Jan 1, 2003

Industries in the Kwinana area have embarked on a journey of improving the eco-efficiency of Western AustraliaÆs primary heavy industry area. The Kwinana Industrial Area has some unique characteristics that provide both opportunities and barriers. The Kwinana Industries Council and the Chamber of Commerce and Industry are working with the industries to identify a range of projects that can deliver improvements for both environmental and economic æbottom linesÆ, and to progress these projects using internal and external resources. The evolution of the process, its relationship to the ethos of operating companies, and the availability of resources to pursue projects, is an interesting study with lessons for others interested in taking the same course.

Jan 1, 2002

By T. Dlokweni

Several Rockmass classification systems have been developed and used in Civil Engineering design and for underground mining operations. Some of these rockmass classification systems have been modified and used in the South African coal mining industry to quantify descriptive geological information for use in coal mine design and roof support selection. The Coal Mine Roof Rating (CMRR) system developed in the USA has been investigated in detail as part of the study. Advantages and disadvantages of the system have been identified by means of underground and surface borehole testing. Investigations into the rating systems in South Africa found that most of the rating systems used in the South African coal mining industry are for planning purposes, and are conducted on borehole cores. This study also highlighted that the rating systems being used are based on geology, and that the human factor plays a major role in the rating systems. To overcome these problems, all the classification systems used in South African coal mines have been benchmarked against impact splitting technique and documented. The best elements of these systems are combined into a new standard system that will be easily used by all mine geologists and rock mechanics engineers. Plusieurs systèmes de classification de la masse rocheuse ont été développés et utilisés dans le Génie Civil et pour les opérations d'exploitation minière souterraine. Certains de ces systèmes de classification de la masse rocheuse ont été modifiés et utilisés dans l'industrie minière sud-africaine pour quantifier l'information géologique descriptive utilisée dans la conception de mines de charbon et la sélection de soutènement du toit. Le système d'Evaluation de Toit de Mine de Charbon (CMRR) développé aux USA a été examiné en détail, comme part de l'étude présente. Tests en surface de trous de mine ont permis d'identifier les avantages et inconvénients du système. Une étude des systèmes d'évaluation en Afrique du Sud a révélé que la plupart des systèmes d'évaluation utilisés dans l'industrie minière sud-africaine sont utilisés pour la planification, et sont menés sur les carottes de trous de mine. L'étude présente a aussi souligné que les systèmes d'évaluation utilisés sont basés sur la géologie, et que le facteur humain joue un rôle majeur dans les systèmes d'évaluation. Pour surmonter ces problèmes, tous les systèmes de classification utilisés en Afrique du Sud ont été référencés en termes de technique de fissuration sur choc, et documentés. Les meilleurs éléments de ces systèmes sont combinés dans un nouveau système standard qui sera utilisé aisément par tous les géologues de mine et les ingénieurs miniers. Verschiedene Gesteinsmassenklassifikationssysteme wurden entwickelt und kamen im Design für Hoch- und Tiefbau und Untertageabbau zum Einsatz. Einige dieser Gesteinsmassen-klassifikationssysteme wurden modifiziert und sind in der südafrikanischen Kohlebergbauindustrie in Verwendung, um beschreibende geologische Informationen für die Anwendung im Design von Kohlebergwerken und der Firstabstützungsauswahl quantitativ zu beschreiben. Das in den USA entwickelte Kohlengrubenfirstbewertungssystem (CMRR) wurde als Teil der Studie im Detail untersucht. Vorteile und Nachteile des Systems sind mittels der Untergrund- und Oberflächenbohrlochprüfung gekennzeichnet worden. Prüfungen der Bewertungssysteme in Südafrika ergaben, daß die meisten Bewertungssysteme die in der südafrikanischen Kohlebergbauindustrie benutzt werden, Planungszwecken dienen und werden anhand von Bohrlochkernen durchgeführt. Diese Studie hob auch hervor, daß die verwendeten Bewertungssysteme auf Geologie basieren und daß der menschliche Faktor eine Hauptrolle in den Bewertungssystemen spielt. Um diese Probleme zu überwinden, wurden alle in südafrikanischen Kohlengruben benutzte Klassifizierungssysteme vergleichsweise in Hinblick auf Spaltschlagtechnik überprüft und dokumentiert. Die besten Elemente dieser Systeme werden in ein neues Standardsystem kombiniert, das leicht von allen Grubengeologen und von Gebirgsmechanikingenieuren benutzt werden kann.

Jan 1, 2003

By Don W. Deere

Faults under high rock cover represent some of the most severe ground conditions a Tunneler can encounter. High ground water pressures and flows are usually associated with mountain faults. Ground behavior can range from blocky ground to flowing sands and squeezing clays. Sticking a IBM within a fault zone for many weeks, with the disastrous financial consequences, is still a common occurrence. Interpreting the geology and detecting the location of a fault prior to penetrating it is a fundamental step to successful tunneling. Ground water control through predraining or pre-grouting is the second fundamental step. This paper discusses techniques applied for detecting and crossing mountainous fault zones through the use of case histories across the globe.

Jan 1, 2007