Search Documents

By Stuart McTavish

"Noranda's Goldstream mine is a 1,500 ton per day copper-zinc mine located 60 miles north of Revelstoke, B.C.The orebody which contains 3.69% Cu and 2.69% Zn was discovered in 1972. Construction of the mine and mill was completed in 1982 and start up was achieved in May 1983.This paper will describe the flowsheet and related equipment 1n the crusher and mill, in particular the dewatering section where two Larox pressure filters are used to dry the concentrates.INTRODUCTIONThe Goldstrean property is located 60 miles north of Revelstoke, B.C. in the Goldstream River Valley (Figure #1). It was discovered during the construction of a logging road in 1972. Exploratory drilling was initiated in 1975, and in 1976 a portal was collared to obtain underground data. Samples were taken from the underground workings for metallurgical bench tests and a pilot plant run.Due to economic conditions, the decision to go into production was delayed until 1980. Concentrator construction and underground development progressed simultaneously during 1981 and 1982, and were completed by the end of 1982. Start up of the concentrator was achieved on May 2, 1983.The ore typically contains about 40% sulphides, which are chalcopyrite 10%, sphaletite 6%, pyrrhotite 20%, and pyrite less than 5%. The sulphide minerals have a high degree of intergrowth. Most of the sphalerite occurs in micron sized grains which are embedded in the pyrrhotite and, to a lesser degree in the chalcopyrite. There is also some fine dissemination of the chalcopyrite in the pyrrhotite. The waste rock is made up of about 30% quartz, 20% guange silicates, and 10% carbonates. The ore has a specific gravity of 3.2 and a natural pH of 8.2."

Jan 1, 1985

By P. Jurovcik, D. Yantek, D. Ingram

The National Institute for Occupational Safety and Health (NIOSH) identified hearing loss as the most common job-related disease in the United States in its 1996 National Occupational Research Agenda. Previous studies by NIOSH have shown operators of surface drill rigs without cabs are commonly exposed to A-weighted sound levels exceeding 90 dB. During hammer-drilling, A-weighted sound levels exceeding 100 dB were recorded at the operator station. NIOSH collaborated with a local drilling company to design and install a partial cab between the operator and the drill steel in an effort to reduce the sound level at the operator station. Sound level measurements in the field show the partial cab reduces the A-weighted sound level by 5-9 dB at the operator’s left ear and 2-5 dB at the operator’s right ear while hammer-drilling. This paper will briefly discuss the preliminary design of a cab and the testing of materials for construction of the prototype. Explanation of the ideas behind the prototype design and fabrication will be covered. Finally, the field test method and results will be discussed in detail.

Jan 1, 2007

By M. A. Trevits, M. R. Thibou, A. Ozment, A. C. Smith, J. B. Walsh

The Excel No. 3 Mine is a room-and-pillar mining operation owned by MC Mining, LLC, a subsidiary of Alliance Resource Partners, LP, which produces coal from the Pond Creek Coalbed in Pike County, Kentucky. Late on December 25, 2004, a fire was discovered near the bottom of the slope and, after an unsuccessful attempt to fight the fire underground, it was decided to address the fire remotely from the surface. The mine operator developed a plan to fight the fire that called for the installation of temporary seals at the slope and mine shafts to eliminate the inflow of oxygen. In addition, the plan called for drilling and completion of vertical boreholes into select areas of the mine workings to monitor the mine atmosphere and inject nitrogen gas and gas-enhanced foam. Over the next 9 days, nitrogen gas was injected almost continuously and gas-enhanced foam was injected periodically as deemed necessary. On January 7, 2005 it was determined that the fire was successfully suppressed. This paper presents a discussion of the fire-fighting approach and an analysis of the results of the application of gas-enhanced foam technology.

By F. J. Plaul

The dominating technologies for steelmaking are the basic oxygen furnace (BOF or LD process, Linz-Donawitz) and the electric-arc furnace (EAF). The main iron input materials for both are liquid iron as hot metal, or solid iron as pig iron, DRI (direct reduced iron), HBI (hot briquetted iron) and scrap. Hot metal, pig iron (i.e., solidified hot metal) and DRI/HBI are virgin iron materials, which have to be produced from iron ore by so-called ironmaking technologies. The family of ironmaking technologies includes three process routes: blast furnace, smelting reduction and direct reduction. Driven by steadily increasing costs of raw materials in the last two decades, the sector has seen a number of new developments in ironmaking technologies, developments based on fluidized-bed technology. The main advantage of a fluidized-bed technology is that fine iron ore can be directly charged to the process without prior treatment; it does away with agglomeration and its concomitant cost, a step practised in blast-furnace, COREX® and MIDREX® processes. With Posco of South Korea, Siemens VAI Metals Technologies has successfully developed the FINEX® process, a smelting reduction based on the direct use of iron ore fines to produce hot metal. The key technology is the four-stage, bubbling fluidized-bed-reactor system, in which fine iron ore is reduced to DRI fines in a countercurrent flow with a reducing gas generated by coal gasification. Beside surveying the current state of the art, this paper discusses the technological principles of smelting-reduction and direct-reduction processes. The status of FINEX® and the outlook for further developments are described. Crucial to the successful development of the new ironmaking technologies for the direct use of fine ore was the scaling up of the fluidized-bed reactor system, which demonstrated new design features.

Jan 1, 2009

By William C. McBee

Sulfur concretes have been developed by the Bureau of Mines as construction materials with physical and mechanical properties that suit them for use in acid and salt corrosive environments where conventional concretes fail. Mixture design methods were established for preparing sulfur concretes using different types of aggregates and recently developed mixed-modified sulfur cements Bench-scale testing of the sulfur concretes has shown their potential value. Corrosion resistance, strength, and durability of sulfur concrete are superior to those of conventional materials. Field in situ evaluation tests of the sulfur concretes as replacement for conventional concrete materials are in progress in corrosive areas of 24 commercial chemical, fertilizer, and metallurgical plants.

Jan 1, 1983

By T. Iwasaki

This paper points out two key elements in resource trade in general and the Canada-Japan relationship in particular. The first is that the advanced countries have a more important role than one would expect in the supply of resources in world trade. Canada 's dual role as a major resource supplier in conjunction with an advanced economy will continue to increase. The second point is the heavy reliance on foreign resource supplies in some advanced economies, particularly in Japan. Finally, as regard the future of the Canada-Japan economic relationship, particularly .in resource development, it is suggested that trade could be enhanced by an accelerated exchange of various types of resources between the two countries. These include natural resource commodities as well as the more abstract capital, technological and human resources.

Jan 1, 1978

By F P. Hao

Organo-sulphur-based collectors (eg xanthates, dithiocarbamates and dithiophosphates) are widely used in the flotation of sulphide minerals. Xanthates (ROC(=S)Sû), for example, adsorb strongly at sulphide mineral surfaces, in a reaction that is electrochemically coupled with the reduction of dissolved oxygen. One of the oxygen reduction products, hydrogen peroxide, reacts directly with dissolved xanthate, leading to its oxidative decomposition. Experimental work has been conducted, using ethyl xanthate, to understand the molecular mechanism by which hydrogen peroxide reacts with xanthates. A number of degradation products have been identified, some of which have not been reported previously. This oxidative decomposition reaction pathway is discussed in the broader context of xanthate decomposition in flotation systems. One of the identified ethyl xanthate decomposition products, ethyl perxanthate (ROC(=S)SOû), has been observed in the process water of a number of mineral processing operations. The interaction of this molecule with goethite (α-FeOOH) particles, typical of that found in tailings dams, has been studied in more detail using attenuated total reflectance (ATR)-FTIR. The ethyl perxanthate molecule has been found to coordinate to iron (FeIII) at the goethite surface, and undergo a surface-catalysed decomposition process. In the presence of both PbII and goethite, a ternary surface complex is formed, where ethyl perxanthate is coordinated directly to surface adsorbed PbII atoms. The results obtained give some insight into the environmental fate of ethyl xanthate in tailings streams, and a basis on which to consider the environmental importance of such species in tailings dams. Strategies for the destruction of residual xanthate levels in waste water streams are discussed in terms of the likely reaction products.

Jan 1, 2002

By T. O. Hagan

Analyses of accident records show that a better understanding of very basic strata control principles and practices, by production personnel, will improve worker safety. Workers, lack of knowledge, with respect to aspects of strata control, increases their exposure to such strata control risks. The primary objective of the Safety in Mines Research Advisory Committee (SIMRAC) project 02 02 07 was to develop tools for the transfer of strata control knowledge. Four such tools were developed, three of which focused on illiterate underground mine team members who are not yet able to take advantage of the Mining Qualifications Authority (MQA) learning process (see project outcomes 2, 3 and 4 below). The tools were designed to equip these workers with sufficient knowledge and ability to work safely underground until such time as they can take advantage of the MQA system. Project outcomes: 1 A four-minute video using animation to illustrate the causes and prevention of falls of roof in South African collieries. 2 Software to demonstrate the capability of reconstructing, interactively, accident scenes and actions that have taken place underground in stopes. 3 A strata control bridging course for illiterate mine team workers. 4 Small-scale wooden models that will be used to design life-size mock-up facilities to assist with the above mentioned bridging course. 5 Workshops and presentations to demonstrate the outcomes 1to 4 above.

Jan 1, 2005

By K. Rambha Devi

The paper is an attempt to co-relate the findings of pile capacity using a number of formula suggested by various authors with the actual field load test results. Five locations consisting of wholly sandy or clayey soils were selected for this purpose. The clayey soils are on a hilly area having clays of medium to stiff consistency upto a depth of 20 m The sandy soils are near the bank of a river having angle of internal friction 'Ø' value ranging from 30 to 35 Degree. The details of the soil properties are given in Table-1 Bored cast-in-situ piles of 30 cm diameter and a length varies from 6.5 m to 13 m were designed and cast for load test to be carried out. The load applied was twice the design load. The load vs settlement curves were obtained. The theoritical values obtained by formula suggested by various authors were superimposed on the curves. From the careful study of these curves it is seen that De Ruiter and Berigen values are close to the actual results for clayey soil. For sandy soil it is found that both the BIS method and Meyerhof method found to give conservative resuslts. A multiplication factor is suggested to theoritical values for obtaining satisfactory results.

Jan 1, 1996

NATURE OF ORETHE Edna May ore consists mainly of clean quartz of a moderately hard and tough nature. The gold content is "free" and fairly coarse, so that a large percentage is recovered by amalgamation. The ore is practically free from metallic minerals.GENERAL OUTLINE OF PLANT AND TREATMENTThe ore, received from underground in trucks, is broken by a jaw breaker, then stamp-milled, follow~d by partial filie-grinding in pans. Mercury is used both in the mill boxes and pans. The pulp, on leaving the pans, passes over amalgamating tables and is then elevated by tailings pulp to cone classifiers and separated into a sand and slime product, each product receiving a separate cyanide treatment-sand by leaching in vats and slime by agitation and decantation in a "Trent" plant. Gold solutions from both sand and slime are precipitated together by zinc shavings in the usual type of precipitation boxes. Accumulated slime is trucked from the dam to a vortex mixer and from this point receives with the cement slime the same treatment.ORE BREAKING AND TRANSPORTThe ore is trucked from the brace of the shaft along an overhead line to the breaker station. Hence it is, by means of a "kick-up" dumped upon a grizzly, set with 2-in. spaces, the oversize being broken by a 15 x '9 Fraser and Chalmer jaw...

Jan 1, 1919

Although cyclones have been around in their current form since the early-1890s, there have been some exciting new developments, which have extended their efficiency/operation. These developments have taken place with both dense medium and classification cyclones. The more noteworthy developments are:Inlet designInlet design is the determining factor in classification cyclone capacity and efficiency. The recently developed ribbon inlet with patented pressure bulge has not only resulted in unbelievable increases in capacity, but also in efficiency. Sharpness of separation corresponding to an alpha value of greater than four has been achieved! Secondary offtakeOne of the factors leading to reduced cyclone efficiency is the presence of coarse particles in the cyclone overflow. The secondary offtake has been developed specifically to scavenge these particles from the cyclone overflow with great success. Water injectorThe other major factor resulting in reduced cyclone efficiency is the presence of misplaced fine particles in the cyclone underflow. The water injector, which has been around for many years in various forms, can reduce this short circuit fraction by up to 50 per cent. 3-in-1 cycloneThe 3-in-1 cyclone combines the inlet design, secondary off take and water injector into a single unit resulting in the most efficient classification cyclone available in the market. The RejectorTMIron ore has a high yield to underflow and traditional dense medium cyclones have always been spigot constrained. The Rejector TM is an exciting new development whereby the spigot capacity has been increased substantially. The application of the Rejector TM will result in fewer/smaller cyclones being required for a given duty resulting in efficiency gains and reductions in both operating and maintenance costs.

Jan 1, 2002

To maximise recovery by highwall mining, pillars must be designed which are long, slender and of relatively low width-to-height ratios. The strength of pillars with width/height less than 2 depends primarily on the mechanical response of the coal, due to the reduced influence of frictional restraint between roof and floor. A suitable pillar design approach therefore requires a method of estimating coal-seam properties. Experimental studies were carried out to determine ways of reliably predicting the large-scale mechanical properties of coal seams from small-scale test data. The studies led to a method of practical, systematic assessment of coal-seam properties based on measurement of coal rank and seam brightness profiles. The criterion employs the parameters sigma(c), m and s of the generalised Hoek-Brown empirical strength criterion for rock masses. A novel design approach combines the flexibility of modern numerical modelling programs with simple hand calculation for rapid assessment

Jun 21, 1905

By R. Cao

Geostatistics was initially developed in the mining sector, but has been extended to other geoscience applications, including forestry, environmental science, soil science, and petroleum science and engineering. This paper presents methods, workflows, and pitfalls in using geostatistics for hydrocarbon resource modelling and evaluation. Examples are presented of indicator variogram analysis of categorical variables, lithofacies modelling by sequential indicator simulation and hierarchical workflow, porosity modelling by kriging and stochastic simulation, collocated cokriging for integrating seismic data, and collocated cosimulation for modelling porosity and permeability relationships. These methods together form a systematic approach that can be effectively used for modelling natural resources.

Jan 1, 2014

By R. B. Barlow, J. A. C. Fortescue

Originally developed for use in mineral exploration, regional geochemical mapping based on stream (and lake) sediment sampling is showing broader application in other areas of the earth sciences and in environmental science. The purpose of this paper is to focus attention on the role of regional geochemical mapping in relation to geological and environmental studies. This is achieved using a descriptive equation for the chemical composition of a stream-sediment sample and then relating it to the use of successive approximations in geochemical and environmental investigations. The procedure is further qualified with reference to time and process in the formation of regional geochemical patterns. Examples are included of studies based on stream sediments related to bedrock geology, surficial geology, ecology and man's effect on the geochemistry of the environment. The range of applications of regional geochemical mapping in earth and environmental studies is outlined and some conclusions drawn regarding the future development of geochemical mapping under Canadian conditions.

Jan 1, 1980

By A. Iannacchione

Longwall mining began within the Pittsburgh coalbed of Pennsylvania (PA) in the early 1970?s. Originally, longwall mine layouts were designed to fit within existing room-and-pillar operations, where panels were limited to that of typical production panels, e.g. a few hundred feet wide by a few thousand feet long. In these early designs, the gate entries were comprised of chain pillars similar to those found along main entry systems or within pillar recovery sections. The modern longwall mine has little in common with their 1970?s predecessors. Today the entire mine layout is designed around the longwall mining method. The longwall panels have grown to well over one thousand feet in width with lengths now measured in miles. In addition, development pillar sizes and shapes are matched to specific performance requirements.

Feb 27, 2013

By A. Cichowicz

In this study, techniques used to design earthquake-resistant structures are applied to the deep-level mining environment. Earthquake engineers seek to identify the cause of potentially damaging resonance, and design or reinforce structures to reduce these effects. Similar techniques have been used to analyse the dynamic behaviour of the rock mass surrounding a stope in a deep South African gold mine. A three-dimensional seismic array installed in a stope at TauTona Mine (previously Western Deep Levels, East Mine) provided an opportunity to examine the evolution of the wave field close to an underground opening. A set of three-component geophones installed in a borehole above the panel revealed the development of surface waves as wave fronts reached the excavation, and an array of vertical component geophones fixed to the hangingwall provided a two-dimensional map of site effects. While the collected data do not include damaging seismic events, quantitative analysis enabled phenomena which could lead to damage, to be recognized. In the vicinity of the excavation, the energy of the seismic signal is generally transformed from high frequency to low frequency. It was found that seismic events with relatively high corner frequency (150 Hz?200 Hz) usually excite several modes of vibration (30 Hz to 110 Hz), while events with low corner frequency (30 Hz?50 Hz) do not always excite higher modes of vibration in the structure. This implies that the rock mass around the excavation is a complex medium, and should be studied using the multi-degree-of-freedom model. A strong structural effect (due to the excavation shape) was revealed as a low frequency coda wave (at 40 Hz and 60?70 Hz), well developed on the skin of the hangingwall. A strong site effect was revealed by changes in signal properties between hangingwall geophones, exhibiting strong resonances around 160 Hz and in the range 200 Hz to 300 Hz.

Jan 1, 2000

Discrete Element Method - Computational Fluid Dynamics Modelling of Flow Behaviour in a Stirred Mill - Effect of Operation Conditions

Sep 13, 2010

The Calypso geothermal field, mapped by the R V Sonne (cruise SO-135) in 1998, includes four main sites, the Northern Vent Area (centred on 37¦ 36.7'S, 177¦ 06.2'E, area 1.5 km2), Central Vent Area (37¦ 39.4'S, 177¦ 05.2'E, 1 km2), Southern Vent Area (37¦ 41.7'S, 177¦ 06.0'E, 1 km2) and Mercury Vent Area (37¦ 41.3'S, 177¦ 07.3 'E, 0.5 km2). Hydrothermal activity at the vent sites is controlled by minor, sub-parallel NE-trending normal faults. Gas bubble trails (C02) and shimmering hot water vent from fractures and joints between large blocks of silicified volcaniclastics and in depressions in the sediments at the base of these outcrops. Measured maximum vent temperatures are between 180¦C and 201¦C. Venting fluids are at, or just below, boiling for water depths of 200 m. Rock samples recovered by dredge from the sites include massive anhydrite, clay-altered pumiceous ash, silicified volcaniclastic sediments and volcaniclastic breccias cemented by sulphur. Clay-altered samples, dominated by randomly interstratified illite-smectite and accessory chlorite, indicate formation environments of 70¦C to 90 ¦C. Native sulphur is abundant throughout the samples. Fine-grained (<1 mm) disseminated pyrite and vein pyrite occurs in the clay-altered pumiceous volcaniclastics and argillites. In the Southern and Mercury Vent Areas, fine-grained orpiment, realgar and cinnabar have deposited in the sandy matrix of volcaniclastic breccias. Amongst the cinnabar, small (<2 mm) beads of native Hg formed on the surface of several rocks following their recovery. These samples also contained abundant light hydrocarbons, which coat the rocks with an oily sheen.

Jan 1, 1999

By F. Tailoka

Bi was electrorefined from alloys containing 10-90 wt% Pb, together with Cu and Ag as minor impurities, in a basic cell and in a recessed-channel cell with 27.5:72.5 NaCl-PbCl electrolyte at 450-470 degrees C and 10 000-20 000 A/m2. The voltage in the basic cell was as high as 9 V, with some carryover of Bi to the cathode observed, whereas in the recessed-channel cell it was as low as 285-635 mV. Flow patterns observed in a room-temperature model indicated that the recesses provide both static liquid hold-up and good mixing of the alloy, enhancing cell performance in combination with the reduced anode-cathode distance of 0.90 mm. The purity of the resulting anode product is as high as 99.9%

Aug 1, 1995

By R. L. Virta

Four companies ? H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. ? mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.