Search Documents

Bioremediation of Acid Mine Water Using Fly Ash and Desulfotomaculum nigrificans One of the major concerns for the mining industry especially after the mine closure is the generation of acid mine drainage (AMD), and its discharge into the environment surrounding the abandoned mines, leading to serious environmental pollution. AMD is usually characterized by high concentration of dissolved metal ions, sulfate and low pH. The efficacy of fly ash was assessed for the removal of metal ions such as iron, zinc and copper as well as sulfate from synthetic acid mine water. Complete removal of ferric and ferrous, 80 per cent of Zn, 83 per cent of Cu and 62 per cent sulfate removal could be achieved, with a concomitant increase in the pH value from 2.3 to 7 using fly ash as an adsorbent under appropriate conditions. The free energy of adsorption of the metal ions onto fly ash was found to be negative, while the adsorption process was endothermic and adhered to the Lagergren pseudo-first order rate equation. Bioremediation studies using a typical sulfate reducing bacterium namely Desulfotomaculum nigrificans, after pre-treatment of the synthetic acid mine water with fly ash, cumulatively resulted in about 94 per cent zinc, 100 per cent copper and 90 per cent sulfate removal. The possible mechanisms of metal ion removal and sulfate reduction from acid mine water utilising Desulfotomaculum nigrificans are discussed.

Sep 13, 2010

By L. R. Stace

Arguably, one of the most significant technological breakthroughs that had been experienced during the period when British Coal was the major coalmine operating company in the UK, the use of rockbolts as principal support in underground roadways brought with it the need to re-assess the technical knowledge, management controls and legislative frameworks associated with the support of mine workings. Following a major roof fall in a roadway supported principally using rockbolts in which fatalities occurred, the process of the design of rockbolted support and the systems and procedures that had been put in place to control its use in the UK were further reviewed. The paper discusses the outcome of these reviews, and how the incident initiated a major new interest in strata control research in the UK against the background of the fragmentation of the ownership of the mines following the sale of the former British Coal assets at the end of 1994, together with the proposed introduction of new strata control legislation in 1996.

Jan 1, 1996

I have chosen this subject in view of the fact that, while there are many and ample opportuuities of getting reliable assays made, there are but few who are in a position to obtain reliable data on the sampling of minerals and metals my long experience at Port Pirie, where, for five years, I had charge of the Refining and Sampling Mill, showed me how important it was that a correct sample should be taken.Weighing; This, to the ordinary layman, seems so simple that no expert knowledge is needed, but in actual practice there are hundreds of pounds to be lost by the lack of knowledge in this department.(1.) There is the matter of weighing in large or small quantities.(2.) The class of weighing machine used.(3.) The accuracy of weights used.We all know that, say, 1000 tons of ore cannot be weighed in one parcel; but the fewer the weighings the less loss to the seller (and usually wishes it weighed in small lots carefully) for it is a well known fact that the most sensitive scales take a certain weight to show distinctly the indication of the balance, or, in other words, what is known as "the pull of the scales." As for instance, 1000 tons weighed in lots of 1 c. each, taking the pull of the scale as being equal to 1 lb., would give a result of 9 tons loss to tbe seller, and as most of the ore sent to Customs works is worth 5. -£20 per ton-this would mean £180 loss to the careful man.

Jan 1, 1901

By Ken Andromalos

Continued population growth combined with limited water resources in the Denver area has resulted in the conversion of a number of mined out gravel pits in the area into municipal water storage facilities. The use of slurry walls provides a cost effective means of isolating groundwater to convert these pits into efficient water storage facilities. Design considerations include: stability, underlying bedrock conditions, backfill mix design and earthwork requirements. Installation issues during construction include: trench stability considerations when excavating through relatively clean sand and gravel deposits in potentially high groundwater conditions; keying into three to ten feet of fractured claystone, siltstone or sandstone that makes up part of the Denver formation, and quality assurance procedures to assure a proper groundwater barrier is constructed. The paper concludes with two brief case histories to illustrate how these considerations are applied

Jan 1, 2007

By Robert B. Bittner

Large diameter piles (2 to 3 m diameter, both driven and drilled) are being used more frequently by designers of bridge foundations. The use of these large piles allows the pile cap to be positioned off the bottom but usually still below water. Conventional cofferdams as shown in Figure 1 below are not suited to this type of pile cap. However, float-in cofferdams offer a viable alternative. This paper describes the float-in cofferdam system, its initial development for use on the Bath-Woolwich Bridge in Maine and its most recent application on the new Carquinez Bridge in California.

Jan 1, 2013

Objective To develop safety training tools for mine safety and health professionals that fill gaps in currently available materials. Background Over the past 4 years, NIOSH has developed and released a series of training videos targeted at underground mine safety. These videos were developed in close cooperation with the mining industry and safety training professionals and were intended to provide realistic, interesting, effective training to both new hires and experienced miners. The videos cover the mining cycle, starting with the breaking of the rock (Handling Explosives in Modern Mines), making certain the work area is safe after a blast (Rock Falls— Preventing Rock Fall Injuries in Underground Mines), installation of ground supports and recognition of failed supports (Miner Mike Saves the Day), and hauling both ore and materials in the mine (Hazards in Motion). A separate video (Hidden Scars) captures the story of a fatal rock burst through an interview with a miner who nearly died and who lost his partner in the accident. These videos have been extremely popular in the mining industry and are being used across the nation as well as in 18 other countries. Two of them, Rock Falls and Miner Mike Saves the Day, have won Alice Hamilton awards, NIOSH’s highest recognition for Excellence in Occupational Safety and Health, in the Educational Materials category. Approach A recently completed independent evaluation of the SRL mining videos identified five themes that mine safety trainers consider necessary for successful training materials: high quality, credibility, accurate content, effectiveness, and an engaging nature. All of the NIOSH videos were rated very high for each theme. Using these measures of effectiveness, a more difficult challenge has been undertaken. Much has been written in the mining industry about the coming turnover in employment. The average age of miners in the United States is approaching 50, and many of the “experts” will be leaving the industry as they reach retirement age. The mining industry, like many industries involving skilled labor, relies heavily on a master-apprentice relationship between new hires and older miners. New hands learn from experienced miners. Their learning falls into three primary categories—they learn what’s important to know, they learn how to do things correctly and safely, and they learn the culture.

Mar 1, 2002

The geologist is often called upon to give judgment on the possibilities of reviving a former mining field presumably worked out as far as the evidence then available indicated. From time to time, scarcity and consequent high prices of metals has led to there-examination of many old fields. The possibility of resuming investigation on them where the practical miner ceased work, even where he had the aid of the trained geologist, has long since disappeared.Means of access to mines have been removed and water fills the workings. Hence an indirect mode of attack becomes essential.This method depends mainly on past history, and may be described as a reaching out by faith supported by shrewd guessing from the known to the unknown. Apart from whatever general intelligent observations may be made in situ of the evidence of former mining activity, the method depends largely on the examination of the past history of the field as revealed in the official records, company reports, plans of underground workings, local newspaper accounts, and the testimony of practical miners formerly employedon the field, the' reliability of which has to be carefully sifted. The matter derived from the examination of these sources must next be rigorously collated and correlated where possible. When the review of all individu!1l features and aspects has been completed, tentative and speculative conclusions may be drawn which, though not verifiable before the event, will usually prove to be more serviceable guides in exploratory operations than mere "blind stabbing."As an actual illustration of what is involved in the mode of procedure outlined above, the following is the description of an investigation in which the writer took part.In 1937, during the course of the Commonwealth Aerial, Geological and Geophysical Survey of Northern Australia, a detailed geological investigation was undertaken of the Croydon gold field, situated near the south-eastern. extremity of the Gulf of Carpentaria in North Queensland.The history of the field briefly is as follows: It was discovered in 1885, reached its peak of production 1896, declining thereafter till 1906, when operations ceased. The total production was about 1,000,000 ounces of gold bullion, containing approximately 40 per cent. of silver. The gold bullion was won from flat-dipping quartz reefs, which yielded an average of 2.oz. to the ton, and the maximum depth to which production occurred was 500 feet. Subsequent prospecting below this depth failed to locate further ore.In consequence of the inaccessibility of the mines and the almost total masking of the' surface by alluvium, the investigation of future possibilities became largely an. office ,study, which was conducted under the following headings:-1. Recording of factual data of each mine separately.

Jan 1, 1950

By Valérie Tremblay

Plan de la presentation ?Laboratoire d?analyse des fluids ?Gestion des contaminants ?Condition Monitoring Avantages reliés aux analyses ?En savoir plus!! ?pour minimiser les coûts d?opération; ?pour prévenir les défaillances catastrophiques; ?pour maximiser le rendement des équipements; ?pour maximiser la longévitédes équipements; ?pour permettre des périodes d?entretien planifié.

Feb 1, 2008

By D. Shin

The gold leaching using cyanide from ore or waste has been almost universally in use [1]. Recently, biological gold bioleaching using cyanide producing bacteria, e.g. Chromobacterium violaceum, Pseudomonas fluorescens, or P. aeruginosa, has been investigated as environmental friendly and cost effective method. Among them, C. violaceum has been reported as effective cyanide producing bacterium on gold leaching [2, 3]. C. violaceum produces cyanide using glycine as a direct precursor and subsequently detoxify the cyanide by ß-cyanoalanine synthase [4]. However, until today only 0.026 ? 16.9 mg/L of cyanide production in YP medium has been reported in the literatures by C. violaceum [4-6]. Comparing with adding cyanide chemical, biogenic cyanide concentration is lower than the cyanide concentration added in traditional cyanidation. Since cyanide also forms complexes with a number of other elements such as iron, nickel, zinc, silver, copper, and platinum, it is very important for gold recovery to investigate the enhancement of biological cyanide production and set optimal experimental condition. Most of early studies on gold bioleaching by C. violaceum have been performed to investigate gold leaching mechanism using gold powder, and recently various resources such as ores, electronic scrap, and printed circuit boards of waste electronics [7]. Few studies have dealt with gold bioleaching from low-grade ore. In this research the feasibility of gold bioleaching by C. violaceum from low-grade ores containing gold was evaluated and fundamental study was performed for further scale-up study. The aim of this study was to improve the potential of gold bioleaching by C. violaceum from gold-containing ore; in particular, enhancement of biological cyanide production.

Jan 1, 2012

By Benjamin H. Clark

"For over 50 years, Derrick Corporation has been renowned for its innovative and durable fine screening equipment and screen surface technology. Derrick’s latest innovation, the patented Stack Sizer, offers mineral processors both high tonnage capacity and high separation efficiency on an extremely small footprint.The Stack Sizer is suitable for separations from 6.3 mm down to 75 microns (200 mesh). The Stack Sizer, coupled with Derrick’s patented urethane screen surface technology, offers an extremely economical alternative to hydraulic classifiers, hydrocyclones, and less efficient low volume wet screening systems. Stack Sizers have been used in feed preparation for flotation, spirals, and a variety of jigs. Mineral processors wishing to reduce grinding circuit circulating loads and generation of slimes due to over grinding, thereby enhancing the efficiency of flotation and gravity circuits, now have another technology at their disposal to perform this critical sizing and grade control function.Over 200 Stack Sizers have been installed in numerous mineral processing applications worldwide attesting to the rapid acceptance of this technology. Stack Sizers are currently screening ferrous and non-ferrous metal ores, mineral sands, silica sand, kaolin clay, feldspar, garnet, phosphate, aluminum dross, potash, coal, tantalum, spodumene, niobium, and other rare earth mineral ores.INTRODUCTIONDerrick engineers have long understood and demonstrated the importance of screen width in coupling both high capacity and high separation efficiency for fine wet sizing applications. As opposed to fine dry sizing, where the length of the screening machine is critical for high separation efficiency, introducing slurry feed to screens in a thin and even layer at minimal velocities across wider screen surfaces allows for high capacities and efficiencies, with maximum screen cloth life. This is due primarily to the combination of free liquid and high frequency vibration of the Derrick motors, which allow fine undersize material to pass through the screen apertures. Lacking either of these factors would be extremely detrimental to the screening process. Without the high frequency vibration of the motor, the screen is essentially a low efficiency sieve bend. Without the free liquid to carry fines through the screen openings, the screen is for all intents and purposes a glorified conveyor or dewatering unit, as little or no sizing takes place once the screen is devoid of free liquid. For optimal screening results, Derrick recommends feeding slurry to a screen at approximately 20% solids by volume. Figure 1 shows the Stack Sizer design concept. Note that a single feed point is used to evenly distribute the flow to the five separate feed points."

Jan 1, 2007

By R. W. Baldwin

On page 309, column 1, the second equation should read: Ma-M1 = dlog_Pa M2-M1 d log P2

Jan 1, 1961

By John McDonald, Peter C. Raleigh, Christopher Dishlip

This paper will discuss how the construction management team and the contractor working together on the City of Los Angeles, North East Interceptor Sewer project, managed information on a daily basis. Data was synthesized from various sources including: inspection, survey, instrumentation, laboratory and the tunnel boring machine data logger systems to produce state-of-the-art reports and graphics which will become industry standard. Special emphasis is placed on how the data is managed and interpreted in a clear and objective manner, permitting the tunneling processes to be carefully monitored and suggesting appropriate action to be taken by the construction management team and contractor.

Jan 1, 2005

By José Cayetano

El presente trabajo plantea un proceso para minimizar el contenido de bismuto en las celdas de electrorefinación, a través de la adición de carbonato de bario a la solución electrolito, de forma que el bismuto soluble presente en fase líquida, se precipite sobre la superficie del precipitado insoluble de BaSO4, bajo una coprecipitación por adsorción e intercambio debido al equilibrio dinámico entre el precipitado y la solución de electrolito conteniendo al bismuto. En este sentido, se reduce la presencia del bismuto en el electrolito de cobre en un 75%, adicionalmente se tiene la disminución del contenido de plomo en un 96%, de estaño en 48% y de plata en un 18% aproximadamente.

Oct 21, 2015

By Lewis Dr. Wade

It is really an honor and pleasure to be here at the 231d International Conference on Ground Control in Mining. My name is Lew Wade. Until recently I served as the Associate Director of Mining for NIOSH. That's a position that I recently moved out of and that position is now filled by Dr. Jeffery Kohler. I now serve as the Sr. Science Advisor to the NIOSH Director. The topic of my talk today will be coal mine ground control, a look back at the last 30 years, and then a brief look forward. I will start by talking about coal mine ground control statistics and with just a brief look, those statistics clearly show that you people are making a difference and there have been tremendous improvements. I'll then look at reasons for those improvements and those will include people working together (this conference being a prefect example of that), as well as technology development. In the area of technology development, I will give you my top-ten list of technology developments in the area of coal mine ground control. Then I'll end with a look towards the future and point to some possible future developments. Then, I will be so bold as to issue some challenges to the participants of this conference. Again, if you take the broad look back at underground coal mine roof falls and ground fatalities, you see this tremendous improvement that we have all come to appreciate. We have all been a part of improving the safety conditions for our underground miners and the number of fatalities is orders of magnitude less than what it was at the turn of the previous century. We have every reason to be pleased and proud of what we have been able to accomplish. Now, the question is why. What are the reasons for those improvements? Just look around this room. You see evidence of what I think are one of the principle reasons: miners, mine operators, government workers and researchers, equipment suppliers, people in research and academia working together. Coming together and sharing at a Conference like this over the last 23 years.

Jan 1, 2005

The work to be described is part of a comprehensive research on the influence of impurities on the properties of lead. The author had previously compared an electrolytic lead containing less than 0.002% total impurities with a commercial lead containing 0.008% impurities (excluding oxygen) and had shown that the former recrystallised more readily than the latter under the same conditions of cold work and annealing. This difference in properties was attributed to the difference in purity. Electrolytic lead containing only 0.0005% total impurities has been prepared and cast in vacuo. Some interesting effects have been obtained by working and annealing this lead, and by adding silver to it. The preparation of this lead, and the effects obtained thereon, are described in this paper. Thepaper is divided into the following sections:(I) Preparation of electrolytic lead.(II) Vacuum Casting.(III) Effect of Cold, Work and Annealing on two Electrolytic Leads, having 0.002% and 0.0005% Total Impurities respectively.1 Research Fellow, Dept. of Metallurgy, University of Melbourne.2 Proc. Aust. lnst. Min. Met., 1932, 87, 145.

Jan 1, 1934

By H. Krogerus, P. Niemelä, P. Oikarinen

High carbon ferrochromium is produced by carbon reduction. No replacement for carbon as reductant has yet been developed. The reduction creates a considerable amount of CO-gas. In open and semi-closed furnaces the gas is burned when leaving the burden. In closed furnaces the formed gas is sucked out by a fan, washed and utilised as fuel. The formation of carbon monoxide is presented briefly starting from thermodynamic considerations up to solid and liquid state reduction. The volume, composition and energy content of the furnace gas are discussed, focusing on the raw materials and pre-treatment processes of the furnace feed as well as on the process equipment and control. Outokumpu has been using closed and sealed furnaces and utilising the CO-gas in its Tornio Ferrochrome Works since 1968. Today in Tornio with an annual ferrochromium production of 260 000 t CO-gas production is 186 million m3, representing 68 MWh an hour. At the same time the furnace power input is 95MW. About 98 % of the CO-gas is utilised, whereof 30% in the ferrochrome production itself. This paper focuses on the characteristics and utilisation of CO-gas. CO-gas is secondary energy, which on one hand saves primary electric and fossil fuel energy in ferrochromium production and, on the other, replaces other fossil fuels at the adjacent steel works. The characteristics of the fuel, requirements for utilisation as well as health and safety aspects are discussed. Utilisation of the gas has a high impact on the total dust and gaseous emissions and on the energy optimisation at the ferrochromium and steel works.

Jan 1, 2004

By P. G. Guest

Many of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed, in operating and anesthetizing areas. When ether was first introduced, candles and gas-lights and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions -many of them fatal to patients -have been attributed, with good reason, to sparks from static electricity. In this paper the authors present facts to show the prevalence of static electricity in the average hospital anesthetizing area, and the degree to which this easily developed electrical form of energy constitutes an explosion hazard. An effort is made throughout to explain how static electricity behaves, why it is a hazard, and why certain safety measures are needed and recommended. Following the introduction and a short general discussion of static electricity, which incorporates a glossary of pertinent electrical terms, an account is given of inspections and tests made in a number of hospitals. This account includes many suggestions that should be useful to any person who plans to make similar inspections and tests. However, a comparison of materials and equipment used with those described in the report will reveal, in many cases, the potential dangers and obviate the necessity for tests. The hospital work was supplemented by considerable laboratory research designed to determine the spark energies required to ignite anesthetic-gas mixtures and the exact amount of time involved in developing the usual static charges. The results of this research are reported and the implications examined. The paper concludes with a general discussion of static and related hazards in anesthetizing areas and of the most urgent preventative measures.

Jan 1, 1952

By Wesley T. Holmes

This report describes the second phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected synthetic slag compositions in the Ti02 -A1203 -FeO-Si02 -CaO-MgO system. Both the hot-stage microscope and the strip furnace (melting-holding-quenching technique) were used during test procedure to determine the effects of CaO, MgO, and SiO2 on the liquidus temperature of slags. The liquidus temperatures of slags studied ranged from 1,241° to 1,900° C. The lowest liquidus temperature for each Ti02 plus A1203 plus FeO weight-percent generally occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. In this investigation substitution of either CaO or MgO for SiO2 and MgO for CaO raised the liquidus temperature of more than 50 percent of the reported base slags when Ti02, A1203, and FeO contents were held constant. The results of this investigation may serve as guidelines for determining flux requirements in smelting a wide variety of titaniferous magnetite concentrates or ores.

Jan 1, 1968

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By G. F. Carr

"IntroductionFLUORSPAR has been found at several •localities in Newfoundland, but all the commercial deposits discovered to date are in the vicinity of St. Lawrence, a town on the southeast coast. Most of the veins are within six miles of St. Lawrence harbour, and between sea-level and an altitude of 400 feet. The St. Lawrence Corporation of Newfoundland, Limited, and Newfoundland Fluorspar, Limited, a subsidiary of the Aluminum Company of Canada. Limited. are the two producers.With the arrival of 1953, the St. Lawrence area entered upon its twenty-second •consecutive year as a producer of fluorspar. Production has increased more or less steadily during this period, as is shown by the fact that approximately one-half of the total shipments to date have been made during the past six years. Between four and five hundred men are employed by the industry, and more than $1,250,000 was paid out in wages and salaries during 1952. Shipments during that year reached an all-time high of 81,283 tons valued at $2,484,943, compared with 67,925 tons valued at $1,966,477 in 1951 (1).As a result of an agreement made in July, 1952, with the United States Defence Materials Procurement Agency, production of the St. Lawrence Corporation, Limited, and St. Lawrence Fluorspar, Incorporated, an affiliated company, will •be increased by .approximately 50,000 tons of acid-grade fluorspar per year. The contract extends over a period of four years, or until 150,000 tons of acid-grade concentrates have been produced."

Jan 1, 1954