Search Documents

During the drilling campaign conducted between October, 1942; and May, 1943, to prove the extent of the scheelite deposit worked by King Island Scheelite N.L. at Grassy, King Island, Tasmania, 35 holes were drilled and 606 samples recovered and assayed for their content. Of these, 238 came from outside the limits of the orebody and were for the most part barren, although a few contained some scheelite. The present statistical analysis is made only of the 368 samples taken from diamond-drill cores of the orebody itself.Drilling Pattern and Sampling MethodsFrom the purely statistical viewpoint, it is realised that methods employed in selecting sites for diamong.-drilling, and of collecting samples from drill cores, do not give a completely unbiassed set of data for analysis. Fig. 1 is a sketch plan showing the relativepositions of the drillholes, which were inclined at an angle of depression of 50 deg. The pattern does not conform to a properly randomized and' regularly-spaced grid, the positions of the later holes being determined by the results obtained from previous holes.Statistically, the bias is, therefore, favourable. The unequal spacing of the drill holes and the lack of uniformity in direction of the lines along which the holes were drilled are unsatisfactory from the mathematical viewpoint; but it is realised that these irregularitiesare difficult to avoid in determining by the most economical methods the extent of such an orebody, and are dictated by geological rather than mathematical necessity.Sampling, also, is lacking in complete uniformity. Each sample is approximately 10ft. in length. However, owing to the fact that 100% recovery of core is rarely achieved, and actual lengths of samples taken are ,primarily governed by the length of the drill runs,and secondarily by lithological changes, there is a considerable amount of variation in the sample length.AssayingWith the exception of 28 samples from three drill holes all samples dealt with in this paper were assayed in the Melbourne University Ore-Dressing Laboratory of the Commonwealth Scientific and Industrial Research Organisation. These assays were given to the nearest 0.05% WOg as it was considered that more accurate determination was not possible. This fact has been taken into consideration in the frequency analysis below. The 28 assays determined by the Tasmanian Mines Department were given to the nearest 0.01%.

Jan 1, 1950

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

This paper examines the reform of mining legislation over recent years, the establishment of new Crown land management agencies, and the role of the Crown and environmental groups in nature conservation inNew Zealand. It describes the relationship of the minerals industry to the Department of Conservation and environmental groups over recent years, and the prospects for mineral development on the Conservation Estate in future.

Jan 1, 1995

Characterizing coal mine roof rock is extremely important for hazard assessment, reinforcement, and entry design. The Coal Mine Roof Rating (CMRR) is an innovative rock mass classification that has found acceptance in the coal mining industry. A disadvantage of the original CMRR is that it cannot be determined in advance of mining, because it requires underground observations. An entirely new set of procedures have now been developed to determine the CMRR from exploratory drill core, as described in this paper. The new procedures employ Point Load Tests (PLT) to determine strength parameters that account for approximately 60% of the rating. Both diametral (parallel to bedding) and axial (perpendicular to bedding) PLT are conducted. The diametral tests allow estimates of bedding plane cohesion and rock anisotropy, both of which are critical to estimating susceptibility to horizontal stress. Traditional core logging procedures are used to determine discontinuity spacing and roughness. To ensure compatibility with the original CMRR, the new rating scales were verified by comparing drill core results with nearby underground exposures. To assist mine planners in using the new CMRR procedures, a large database of strength ratings of roof rocks was assembled through extensive point load testing and logging. Over 2000 point load tests (both axial and diametral) have been made on 30 common coal measure rock types from mines representing most U.S. coalfields. This database has been merged with the popular core rating system of J.C. Ferm into a field guide for geologists and engineers. By using the pictorial classification system of Ferm to identify the rock, typical CMRR can be compared with values calculated using the new CMRR procedures.

Jan 1, 1996

By R. H. T. Garnett

N.B. This paper provoked much (positive!) discussion in later issues, with responses from the author (and thanks also for the many private contributions he had received) - see under Garnett R.H.T. Expanded version of a paper originally presented at the Alluvial mining conference, London, 11-13 November 1991 and published in Alluvial mining, Barking: Elsevier Applied Science for IMM, 1991, p.115-156. The usual measure of performance in gold and tin dredging is the R/E factor. It compares actual production or recovered grade for a given period with that estimated from the original sampling. The factor is a multiple of four component factors, each ideally approaching 1.00. The factors are concerned with estimation, selection, excavation and treatment. The estimation factor reflects the errors involved in determining the grade and depth of single drill-holes or pits. An optimum selection factor is achieved by a higher drilling density. The excavation factor is affected by failure of the dredge to excavate the total volume contained within its course. The required dredge throughput rate influences not only the success in digging recovery but also the treatment factor. No two alluvial deposits are the same, but, in general, the greatest divergence from 1.00 is invariably demonstrated by the estimation factor. A major divergence in one of the other factors may also be the cause of the R/E factor being significantly different from 1.00. The component factors are examined in detail and historical trends in R/E factors are discussed

Sep 1, 1991

By Prince Lazarovich, Hrebelianovich

I WAS asked by the chairman of one of the Sessions on Employment Problems to talk about the viewpoint of the foreign workingman. I am not a workingman. I have never done what a work-hand might call an honest day's labor; that is, I have never been in a factory or manufacturing plant or in a mine, though in truth, hard work and I are well acquainted. I was a soldier, am an engineer, have long been actively interested in the most important waterway construction in the near East, have served politics and diplomacy, written books and lectured at universities. My knowledge of the foreign workingman in this country comes from the fact that my own compatriots here at various times came to me and appealed for advice and help, and last year I was asked by the employment manager of a corporation to undertake a welfare job at one of their plants. I went out, saw the plant, talked with the superintendent and outlined certain of my ideas which he personally heartily approved, but which did not find favor with those higher up. I approach the subject of the foreign workman's point of view with the understanding that the industrial employer's effort is for the maximum of efficiency. I am conversant with labor conditions abroad both in industry and agriculture. What I have learned of industrial conditions in America as they affect the foreign immigrant has been chiefly gathered from the cases referred to of foreign workmen who from time to time have come to me with their troubles. In the course of those investigations, in order to give whatever help or advice was possible, I have been impressed with the fact that the great United States industries evidently had- pot yet sufficiently recognized the value of studying the conditions of the workingman in the lands of his origin across the seas. A careful study of that which could be called the moral element in connection with its foreign labor would give industry a knowledge of the man's reason for coming, what' grievances he brings with him, his hopes for a future, and the peculiar character of his capacities. The employer would thereby be enabled to meet the man, to be helpful to him, to aid him and at the same time promote industrial efficiency, inasmuch as a workman who believes that he is being dealt with humanly and squarely is contented and satisfied and will give willingly, and even with pride, the best that is in him; justice and a fair deal is all the man wants.

Jan 4, 1918

By T. G. Paradis, C. A. Mohns

"This paper summarizes the Wren CAT (Clarifier and Accelerated Thickener) deep bed thickener operation at the EKATITM Diamond Mine in Canada’s Northwest Territories. EKATITMs’ thickener project is presented in terms of initial design considerations and present day operating practices. A circuit description summarizes process equipment, reagent systems, and typical process conditions, and details of Wren CAT operating principles are provided. Operating strategies are discussed, with emphasis on process instrumentation and control and operating challenges.INTRODUCTIONThe EKATITM diamond mine, operated by BHP Diamonds, Inc., is located in the Northwest Territories near Lac De Gras, approximately 300 km NNE of Yellowknife, NT. 9000 dry metric tonnes of diamond-bearing kimberlite ore are processed daily. Processing operations commenced in October, 1998.The EKATITM process plant flowsheet features typical steps in diamond recovery plant design. Figure 1 shows the general plant flowsheet. Size reduction and feed preparation are accomplished by crushing, scrubbing, and high pressure grinding rolls (HPGR) through closed-circuit classification with vibratory screens. Heavy medium separation (HMS) is used as the initial stage of heavy mineral concentration. Secondary concentration is accomplished in the recovery plant by attrition milling; wet, high-intensity magnetic separation (both wet and dry); and X-ray sorting.The present budget throughput rate is 9000 dry tonnes per day. This will be increased to 18,000 tonnes during the first ten years of operation. Unlike most kimberlite treatment facilities, which process material from a single ore body, EKATITM’s process plant was designed to accommodate ore from five different kimberlite pipes, each with its own treatment characteristics.All processing, except for primary crushing, is carried out in a temperature-controlled environment in the main process plant building."

Jan 1, 2000

By J. M. Simard, S. Morissette, P. Coursol, P. Mackey

A new, powerful model is presented that focuses on plant logistics and scheduling aspects of the smelting, converting, fire refining and casting operations at the Horne smelter. This plant complex is the largest custom copper smelter in North America. It handles a wide range of feeds and utilizes a number of proprietary continuous and batch technologies that require good scheduling in order to maximize plant capacity and efficiency. The present model was developed by Xstrata Process Support, in collaboration with the Horne smelter, and uses the Arena® software to evaluate the impact of a number of plant variables on the annual copper capacity of the plant. Model development was carried out by Xstrata Process Support, in collaboration with the Horne smelter, through the effective combination of process chemistry knowledge and detailed knowledge of the plant operation (including all material flows and transfers, as well as information such as operating on-line times, plant stoppages and also scheduled and unscheduled maintenance activities). A number of case studies were then examined, including the impact of anode furnace and casting cycle times on annual copper capacity and the impact of a one-crane mode of operation in the converter aisle, which normally operates with two cranes in service. The model predictions were found to match actual plant results very well. The present modelling of plant logistics and the scheduling aspects were found to add important dimensions at the plant with regard to projections of the real-life plant capacity. As demonstrated in the present case, this type of model and application can have a significant impact on optimizing operations at a given plant. This impact is particularly important in the current market environment, where emphasis is on maximizing plant output and lowering costs. These models can help yield the easily obtained gains that are clearly desirable in these times. Xstrata Process Support has developed Arena models for other operations and is available to explore new applications for a win-win situation at other plants, including mines and concentrator operations.

Jan 1, 2009

By Jones S. C

The problem of sealing a fluid serieite zone at a hole depth of 4000 ft was overcome by using a composite non-return valve plug and rod assembly which enabled cement to be forced under pressure into the zoneà

Jan 1, 1966

By B. T. Brady

Recent theoretical, experimental, and field studies conducted by the Bureau of Mines suggest that rock failures may be predicted and, in some instances, controlled. Theoretical studies that were later corroborated by laboratory and field studies predict that a seismic anomaly will precede rock bursts and/or roof falls in mines. The seismic anomaly is predicted to consist of an increase in the number of seismic events occurring in the immediate vicinity where the failure 1s nucleated. This increase will then be followed by a dramatic decrease of seismicity in a broad region that surrounds the location of the impending failure. The dimensions of this region allow a preliminary estimate of the time to failure (measured from the time the seismicity increase began) as well as an estimate of the energy that will be released at the instant of failure. Field observations indicating that this predicted behavior does precede rock bursts and a roof fall are presented in this report. Implications of results to the problem of failure control in mines that experience massive rock failures are discussed.

Jan 1, 1978

By M. S. Miller

With prevailing assumptions that plentiful domestic coal reserves will be available for meeting our Nation’s expectations for on future low emission, coal-fired power plants, major government funding in Clean Coal Technology, and Carbon Sequestration Programs continues to be aggressive. However, after more than a decade of cutbacks in funding for domestic coal-related programs and personnel, there is a growing concern that adequate quantification and qualification of our Nation’s coal reserves is increasingly being compromised. This paper will define the growing concerns and dichotomies that continue to increase, and address the decreasing number of fossil fuel mapping and assessment programs by Federal and State programs.

Jan 1, 2004

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By W. P. C. Duyvesteyn, B. J. Sabacky

Reprinted with revisions from Extractive metallurgy of copper, nickel and cobalt, volume I: Fundamental aspects. ed. Reddy R.G., Weizenbach R.N. Warrendale, Pennsylvania: The Minerals, Metals and Materials Society, 1993. Development work on the Escondida process, concluding with the successful operation of an integrated leach-SX-EW pilot plant and a pilot flotation plant for the upgrading of leach residues, demonstrated that all major process objectives could be achieved. Extraction of 40% of copper in concentrates containing monovalent copper was achieved with essentially no oxidation of sulphide sulphur. The Cu contents of leach residues from four different types of concentrate were successfully upgraded to the original feed grades, giving a product that has potential as a high-quality concentrate for the smelter market. A compact solvent extraction section effectively recovered the ammonia lixiviant for recycling to leaching and selectively transferred Cu into a conventional acid sulphate electrowinning system. High-quality "six-nines" copper cathode was produced on commercial-scale stainless steel blanks, demonstrating that the process will be able to compete effectively in the premium cathode market

Dec 1, 1995

By William E. Souder

Behavioral accidents are a particular type of accident. They are caused by inappropriate individual behaviors and faulty reactions. Catastrophe theory is a means for mathematically modeling the dynamic processes that underlie behavioral accidents. Based on a comprehensive data base of mining accidents, a computerized catastrophe model has been developed by the Bureau of Mines. This model systematically links individual psychological, group behavioral, and mine environmental variables with other accident causing factors. It answers several longstanding questions about why some normally safe behaving persons may spontaneously engage in unsafe acts that have high risks of serious injury. Field tests with the model indicate that it has three important uses: It can be used as an effective training aid for increasing employee safety consciousness; it can be used as a management laboratory for testing decision alternatives and policies; and it can be used to help design the most effective work teams.

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By Eugene Mirsky, Eloy Ramos, May ElKhattab, John Wise, Terrence Carroll, Jose Torres

In 2017, Nicholson Construction Company completed a $72.1 million design-build contract for Miami Dade Water and Sewer Department to replace an existing 54-inch diameter pre-stressed concrete force main that runs from the Virginia Key Central District Wastewater Treatment Plant, under the Biscayne Bay at Norris Cut, to Fisher Island. In order to install the new sewer pipe below the bottom of Biscayne Bay, a tunnel boring machine (TBM) was launched from a 42ft diameter and 89ft deep shaft on Virginia Key and a precast segmentally lined tunnel was constructed towards a 28ft diameter and 72ft deep retrieval shaft on Fisher Island. Both shafts were constructed through sand and highly permeable limestone, primarily the Fort Thompson Formation which is part of one of the most permeable aquifers in the United States and two different techniques were used to ensure a water-tight shaft at each end of the tunnel drive. The launch shaft structure was built using the secant pile technique, wet excavation and a tremie plug. For the tunnel break-in a soil freeze block was installed after the ground was treated with low mobility grout. The retrieval shaft was built using the Deep Soil Mixing (DSM) technique and excavated in the dry. Precedence of any other structure built this deep through hard layers (UCS over 3,000 psi) using this technique was not found. This case study addresses the challenges of constructing watertight underground structures in highly porous ground for launching and retrieving a TBM. Design challenges from complex asymmetric loading, selection and comparison of the construction techniques, the installation and excavation of both shafts, and their performance are also discussed herein.

Jan 1, 2018

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By E. Ozberk

The copper and nickel smelting industries are important contributors to the technical and economic well-being of Canada while some of the smelters are among the largest sources of sulphur dioxide emissions in Canada. A review of the operations in six smelters - Falconbridge Limited, Falconbridge, Ontario; Hudson Bay Mining and Smelting Co. Limited, Flin Flon, Manitoba; Inco Limited, Copper Cliff, Ontario and Thompson, Manitoba; Noranda Mines Limited, Horne Division, Noranda, Quebec and Gaspe Mines Division, Murdochville, Quebec - have shown that about 80% of the total sulphur input to these smelters was emitted to the atmosphere in 1980. A simultaneous review of the existing and emerging technologies which can directly or indirectly reduce the sulphur dioxide emissions indicated that it is possible to reduce the emissions to below 20% of the sulphur input to these smelters. This can be achieved by varying degrees of modifications to the smelting operations and installing sulphur fixation facilities at significant costs which may increase the metal production costs. This would consequently make the competitiveness of the Canadian copper and nickel producers more difficult in the already tough world metals market.

Jan 1, 1983

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009