Search Documents

By N. D. L. Burger

An effective prototype face support system to minimize rockfalls in rockfall-prone mines was developed and patented during a project sponsored by the Mine Health and Safety Council (MHSC). An experimental development model (XDM) roof support unit was developed and evaluated. Mines with rockfall problems in the face areas can use the roof support system to reduce fatalities and injuries in the face area of stopes. The roof support system consists of two similar support units connected to each other via two crank mechanisms. Each unit consists of a headboard supported by a ?wishbone? structure (top and bottom leg). In the first design a threaded bar with struts similar to a scissors jack keeps the legs apart. (In the final version that was field trialed, the threaded bar mechanism was replaced with a hydraulic cylinder). All the components are manufactured from steel. To move the system forward the first support unit is collapsed, the second remaining in the loaded position. The first unit then hangs from the second unit to which it is connected. The first collapsed unit is then manually cranked forward and prestressed. If the required position is still not achieved, the other unit is released and moved forward. The specification for the system was determined and presented at a workshop with industry participants. Different concepts were developed and evaluated against the system specifications. A technology demonstrator was then developed and tested on surface. The technology demonstrator development process included detail design, building and testing of components and subsystems, design reviews and the building and commissioning of the technology demonstrator. The testing of the technology demonstrator was done in a 500-ton hydraulic press, in a mock-up stope and underground. A risk analysis, in which technical, logistical and economic aspects were assessed, was done to determine the critical areas of the system. During the next phase of the project working prototypes were developed for underground tests and evaluation. This process indicated that it was necessary to adjust the system specifications and a redesign was called for. In an iterative process test units were built for purposes of evaluation, specification verification and field trialing. After the successful conclusion of the trials the equipping of a complete production stope started for purposes of integrating the system into the current mining process.

Jan 1, 2008

By N. Dhawan

With ever-increasing demand, low-grade complex ores and strict environmental regulations, metallurgical processing options have become limited. Heap leach technology provides several benefits to combat these issues including low cost, flexibility and diversified process conditions. This paper provides an overview of heap leaching technology with specific emphasis on chemical aspects. Hence, influencing factors, advantages and disadvantages, testing approaches and some fundamentals will be discussed. Finally, heap leach technology for different ore types (copper, nickel, uranium and gold) will be briefly compared.

Jan 1, 2012

By THOMAS LEONBRD WATSON

I. INTRODUCTION. THE results embodied in this paper are based on a careful field- and laboratory-study of the lead- and zinc-deposits of the Virginia-Tennessee district, begun in the latter part of the summer of 1904 and completed in the spring of 1905, preparatory to the publishing of a State report .on them. A separate description of the individual deposits in Virginia is purposely omitted, since I have already described them in considerable detail in a State report. The Tennessee deposits are described here in some detail for the reason that no detailed record of them has yet been published. Practically, this paper summarizes the results obtained from a study of the geology of the ore-deposits of the district as, a whole. (I had the pleasure of visiting the deposits of Virginia and Tennessee with Dr. H. Foster Bain of the U. S. Geological Survey, in April, 1905. Figs. 21 and 22 are from photographs taken by Dr., Bail.) II. HISTORICAL. . The first authentic records of lead-mining .in Virginia date hack more than 150 years; and the old lead-mines at Austinville, on New river in Wythe county, V a., were the first to be worked. Colonel Chiswell, a native of Wales, and one of the earlier adventurers in southwestern Virginia, was one of the first operators of the Austinville mines. Chiswell's operations at Austinville commenced in the year 1750, and closed shortly after the beginning of the Revolutionary War, in the' year 1776, covering a period of about 25 years. From that time to the present, mining has been carried on almost continuously in the Virginia area. For many years after the Virginia mines were operated, mining was confined exclusively to the lead-ores. The zinc-ores

Mar 1, 1906

By E. Pardo-Igúzquiza, R. A. Olea

The bootstrap is a computer-intensive resampling method for estimating the uncertainty of complex statistical models. We expand on an application of the bootstrap for inferring semivariogram parameters and their uncertainty. The model fitted to the median of the bootstrap distribution of the experimental semivariogram is proposed as an estimator of the semivariogram. The proposed application is not restricted to normal data and the estimator is resistant to outliers. Improvements are more significant for data-sets with less than 100 observations, which are those for which semivariogram model inference is the most difficult. The application is illustrated by using it to characterize a synthetic random field for which the true semivariogram type and parameters are known.

Jan 1, 2015

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995

By D. P. Roberts

This paper reviews the use of crush pillars on mines in the Bushveld Complex and the Witwatersrand Supergroup. Stress measurements were undertaken in order to determine the residual strength of these crush pillars. The results from these stress measurements are compared with previous attempts to determine the residual strength of crush pillars using back analysis. It is concluded that the residual strength of such crush pillars lies in a band between 13 MPa and 25MPa. Using the data from the stress measurements, as well as published and unpublished data, a stress-strain curve for a crush pillar with a width-to-height ratio of 2:1 is proposed. Where further work is required, this is indicated in the text.

Jan 1, 2005

By T. Stauffer, B. McGunegle, A. Adu-Acheampong

The Fairmount Minerals, Inc., Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 15-inch-diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially-available, high-volume/low-pressure fans combined with a systematic layout of control structures. The recommended re-design was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2007

By David S. Bowling

The ER-300 Series White Recorders were developed to provide on economical, yet invaluable instrument for those who desire permanent recordings of such data OS displacement, vibration, concussion (air borne effect) and velocity information. The precise monitoring of earth displacements and air blast magnitudes aids quarrymen and construction contractors in estimating safe blasting limits when operating in populated areas. A refraction model is available for recording velocities which permit the determination of weathered zone depths as well as the .depths to other subsurface formations. The dual purpose (Refroction- Displacement) systems ore utilized for velocity studies and displacement - oir blast measurements.

Jan 1, 1990

In most mines using presplitting the final excavated wall shows a zone of damage just below the crest and well defined presplit half barrels. The crest damage (surface dilation) zone varies and is added to by subsequent adjacent perimeter blasting operations. Keeping the preconditioning to a minimum is possible using the methods described in this paper, developed on several diverse and geographically distant mining operations to control crest dilation and preconditioning by presplitting in advance - not just laterally but vertically in advance. The first documented case (Delbridge, Marton and McSweeney, 2004) in the development of the concept was undertaken at AngloGold Australia Pty Ltd's Sunrise Dam Gold Mine (SDGM), located beside Lake Carey, some 730 km northeast of Perth, Western Australia. The mine had been developed in a series of cutbacks to a depth of over 300 m and began underground mining during the latter stages of open cut operations. This mine is fairly unique in that it utilised a single pass vertical presplit which initially extended over three bench heights and after the failure mechanisms were understood, over four benches. The presplit drilling for the three stacked benches started on the floor of the second bench so that any dilation was confined to the surface one bench above the crest and modified perimeter blasting was then developed to curtail damage from blasting adjacent to the new crest. The second case is based on a South African coal mine in the Witbank Coal Measures, 140 km northeast of Johannesburg, Republic of South Africa (RSA). It was important that blasting for optimal wall stability and minimal scaling was developed in advance. A dragline is scheduled to excavate the #2 seam midburden which is the lowest of the economically viable coal seams in the five seam Witbank Coal Measures. Mining of the overburden, coal and partings above the dragline midburden pass are by excavator and truck and each mining layer is individually blasted. The results of presplitting the midburden through the overlying coal seams and partings have provided a presplit with no surface dilation of the midburden crest and ensures any subsequent crest loss is solely due to blasting adjacent to the vertical presplit. Typical of all coal mines in South Africa only vertical presplits are used. Wall control is most commonly delivered by presplit blasting and one common sight after the dust clears is a ridge of broken blocks along the presplit row, usually with a main crack running between the presplit blastholes and often parallel cracks either side of the perimeter line. The surface rock strata or block structures have been dilated by the venting gases and shock waves. Decoupled, fully coupled, single or double deck charges are used depending on a variety of factors, anecdotal practices and perceived benefits. Preconditioning of the crest rock by blasting from above may not be visible to the naked eye (or non-existent in overburden in strip coal mines) but the high speed venting of explosives gases (and often the water in the presplits) preferentially follow existing cracks and structures because there is no developed presplit crack near the surface. This nearly always lifts, shifts and separates the surface structures and geological layers. Stopping the dilation by 'sacrificial' or 'in advance' presplitting has been shown to reduce the crest loss at both metal and coal mines. Drilling and presplit blasting through an upper level of bench or layer provides a degree of restraint to the target layer where the crest must be maintained and any damage caused by the venting gases will not cause concern as it is removed as planned, leaving a stable crest.

May 1, 2010

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Ground probe?s slope stability radar has enabled the Harmony open pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006

By G de Jong, W Sunyoto, K Sari, P Silalahi

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Big Gossan mine is operated by PT Freeport Indonesia and is one of the largest stope-and-fill mining systems in the world. The Big Gossan deposit is a ~200 m wide, 1200 m long and 500 m high steeply north-east-dipping to subvertical skarn body at the Cretaceous-Tertiary Ekmai-Waripi contact. The copper-gold mineralisation, with a 1.3 per cent copper equivalent cut-off grade, occurs mainly proximal to the Ekmai-Waripi contact in the garnet-clinopyroxene prograde skarn at the base of the Tertiary Waripi formation and partly distal to the contact in the tremolite-actinolite retrograde skarn of the Tertiary Waripi formation.The Big Gossan stope mine is designed from 2540 m to 3020 m above sea level. Present active stoping operations occur at level 2540 mL to level 2640 mL and are done in a primary and secondary stoping sequence. The width and length of the stopes is 15 m and 20 m respectively, while the height of the stope varies between 20 m and 40 m, depending on the ground conditions. The stability of the stopes is visualised in the Mathew’s Stope Stability graphs. These graphs and actual Cavity Measurement Scanner measurements on the stope will predict and show the overbreak and underbreak, which affect the reconciliation of the mined stope and also the pillar stability between the primary stopes. Geological factors like major structures, joints, veins and alteration intensity are important factors that correlated with the stability of the Big Gossan stopes.CITATION:Sari, K, de Jong, G, Silalahi, P and Sunyoto, W, 2015. Stope stability at the Big Gossan skarn deposit, Papua, Indonesia, in Proceedings PACRIM 2015 Congress, pp 139–146 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

At a regional scale, the Otago Schist has been divided into textural zones, metamorphic zones, structural transposition zones, and terranes and lithologic associations. Each of these subdivisions reveals aspects of the internal structure of the lithologically monotonous Otago Schist but, to date, a map of the schist derived directly from structural data has not been made. In the present study, digitised structural data from the QMAP GIS were used to make a form line map of Schist foliation which, in turn (and using certain non-unique guiding assumptions), was used to construct a provisional foliation thickness map of the Otago Schist. Contours of dominant foliation (Sp) thickness have been drawn from 4 kIn above to 16 km below the reference level of the Caples-Torlesse terrane boundary in the schist structural pile. A recent revision of the Otago Schist textural zone classification has shown that the grain size of metamorphic white micas increases progressively with textural grade. There also appears to be a correlation between schist mica grain size and foliation thickness. Using mica grain size, it may eventually be feasible to establish the vertical structural position of samples in greenschist facies parts of the schist pile to a precision of ¦ 1 km or better, even if they are in inliers or fault-bounded blocks. Foliation thickness and mica grain size are thus potentially useful tools for research and exploration in the Otago Schist in that they assist with structural interpolation and extrapolation. Even at this early stage of application they can be used to provide hitherto unobtainable, semi-quantitative estimates of displacement on Mesozoic and Cenozoic faults and folds.  

Jan 1, 2001

By Tom Palangio, Ralph M. Olmstead

Video inspection of boreholes with cameras developed specifically for the mining industry is now possible. These designs are reliable, cost effective, and have the flexibility to be used in other applications.

Jan 1, 1998

By Hayward SB, First DM

The Maragorik Prospect represents a partially eroded Pliocene acid sulphate style epithermal gold system hosted within the Sigule Volcanics and Riet Bed sediments which is inferred to have formed from a degassing porphyry body at depth. A regional sinistral rotation provided by transform faults associated with the opening of the Manus Basin imparts a dilational character to mineralised NE trending faults formed parallel to the Warangoi Graben. A controlled-source audio magneto-tellurics (CSAMT) survey has identified E-W trending buried conductors which may represent alteration formed within dilation zones. While some gold mineralisation occurs within vuggy silica at Palang Hill, the target is auriferous enargite (luzonite)-bearing breccias from the LK1 and Gureki areas.

Jan 1, 1991

By T Hirsi, M Weatherseed, T Ritasalo

Cooling tower design has not advanced significantly in the last decade. Recognising this, Outotec has developed an innovative horizontal outflow cooling tower with increased performance compared to conventional design cooling towers.Outotec® Cooling Towers operate today in applications such as spent electrolyte cooling in zinc plants and for gypsum removal before copper solvent extraction. In such applications the use of this latest design has enabled increased production and lower maintenance costs in the downstream operations.In actual operations, the cooling performance has been confirmed at start-up, and has demonstrated that the towers operate in accordance with the CFD modelling. In the last three years these towers have proven themselves in commercial operation to operate with high efficiency and availability.This case study will outline comparative data, collected over two years at a site where both Outotec and conventional cooling towers are operating. The data shows that Outotec cooling towers require less than half the maintenance time of conventional cooling towers, when adjusted to a total solution flow basis. A close partnership approach with the site has allowed continual development, ensuring high availability and high performance.Experience with previous cooling tower installations guided the development of maintenance philosophies and procedures; this resulted in a design where maintenance intensive components were accessible from the top of the cooling tower. This allows safe access to components and maintenance with little or no downtime.CITATION:Hirsi, T, Ritasalo, T and Weatherseed, M, 2015. Improving cooling tower performance with innovative horizontal outflow design, in Proceedings MetPlant 2015, pp 396–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By C M. Wawryk, S L. Garwin, J D. Foden

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Batu Hijau porphyry Cu-Au deposit in south-western Sumbawa, Indonesia is an ideal natural laboratory to study the fractionation of iron isotopes in magmatic rocks that range in composition from basaltic andesite to tonalite. Intrusive rocks are associated with a porphyry system that contains well-preserved early hypogene copper mineralisation. We analysed pre-, syn- and post-mineralisation igneous intrusive rocks. We also separated magnetite, chalcopyrite and bornite from hypogene porphyry-style quartz veins, and measured the Fe-isotope ratios of samples by solution multi-collector ICP-MS. Iron isotopic composition of samples from the magmatic suite show an increasing d57Fe with increasing SiO2, supporting geochemical and textural evidence that the Batu Hijau Tonalites underwent closed system fractionation. Equilibrium and co-existing mineral textures allow the calculation of the following preliminary empirical mineral-mineral fractionation factors at 500°C for certain mineral pairs.Iron isotopes have the potential to provide geothermometric data to complement fluid inclusion data, especially where heating stages have operational limitations and where fluid boiling results in a wide variety of inclusion types that may make analysis difficult.CITATION:Wawryk, C M, Foden, J D and Garwin, S L, 2015. Iron isotope fractionation in magmatic-hydrothermal minerals – a porphyry copper case study from the Batu Hijau deposit, Sumbawa, Indonesia, in Proceedings PACRIM 2015 Congress, pp 389–396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By D. Randolph Berry

Foster-Miller Associates has developed a set of guidelines to permit hoist manufacturers, mine owners, and MESA mine inspectors to design, purchase, install or inspect a safe and effective Emergency Escape Hoist, as required by the Coal Mine Health and Safety act of 1969. A series of surveys were carried out to determine: 1. The attitudes and local needs of the MESA District Managers. 2. Current escape hoist installations. 3. Equipment available for future designs. 4. Foreign methods and equipment for mine rescue. From these survey studies, preliminary guideline objectives were developed.

Jan 1, 2012

Characterisation of Manganese Ores

Sep 13, 2010

By Susan M. Moore

Many challenges are faced by workers in lower-seam (42 inches or less) mines. The lower-seam heights confine mine workers to their knees as they perform their daily tasks such as installing roof bolts, delivering supplies, repairing belt, or cutting coal. Miners working in these lower seams often consider kneepads to be their only line of defense against knee injuries. However, healthy knees do not start and stop with kneepads. Other interventions such as changing postures, proper hygiene, and work station design may also be used to reduce mine workers? risks for developing knee injuries. Incorporating these and many other interventions into a mine worker?s ?way of life? is an important step to ensuring a long, healthy career and retirement. Keeping knees healthy is also a key aspect to reducing costs in low-seam mines as the industry battles rising health care costs, and training/recruitment of replacement workers is time-consuming and costly. Educating the workforce about the possible interventions to reduce knee injury risk is a primary objective for the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). Therefore, NIOSH researchers, along with industry and academia, developed a training package to educate the mining community about some possible interventions beyond kneepads that may be used to help decrease knee injury rates. Increased awareness and simple changes are the first steps to reducing knee injuries.

May 1, 2008