Search Documents

By K. U. Kainer, A. Stark, D. Tolnai, M. Hehenberger, C. L. Mendis, N. Schell, N. Hort

Samples of an as extruded Mg-6Zn-0.6Zr-0.4Ag-0.2-Ca (wt.%) alloy was compressed at room temperature and at 250°C. The in situ deformation tests were performed at the P07 (HEMS) beamline of PETRA III, DESY, with a modified DIL 805 A/D dilatometer with to Kapton windows on the sides and the induction coil opened for the beam to transmit the sample. The deformation rate was 10-3 s-1 the samples were deformed to failure. The diffraction patterns were recorded every 3 s with a Perkin Elmer 1621 Flat Panel Detector. The results reveal that different deformation mechanisms are activated during compression at a given strain value. At room temperature twinning is the dominant deformation mechanism, while at elevated temperature dynamic recrystallization occurs while the contribution of twinning to deformation is significantly reduced. The compressed samples were further investigated with conventional metallography and SEM-EBSD to determine the volume fraction, the type of twinning and the strain retained within the grains. The parallel testing of pure Mg samples under the same conditions allows comparison of the compression behaviour of the ZKQX alloy with Mg.

Jan 1, 2014

By E. S. Chalpin

On 25 August 1971, the U.S. Bureau of Mines contracted with the Aerojet Liquid Rocket Company to perform an engineering research program to be completed on 25 May 1972. The program objective was to evaluate the advantages and disadvantages of the underground use of several power sources including but not limited to a closed cycle diesel, electric cable/motor, rechargeable battery/ motor and exhausting diesel for mine shuttle cars, with emphasis on health and safety. This report, Research in Advanced Power Systems for Mining Health and Safety consists of four (4) main parts: (1) Hazards and Safety Analysis of Mine Power Systems, (2) Evaluation of Closed Cycle Diesel Power System for Mine Applications, (3) Closed Cycle Diesel Power System Consumables Compatibility, and (4) Concluding Remarks and Recommendations. The hazards introduced to a mine by shuttle car power system failure modes were evaluated and reported. A "fault tree" analysis was generated for each power system and the probability of death or injury during an eight (8) hour shift and for a week of operation (105 hours) were estimated. Advantages and disadvantages were also reported for each system studied. Aerojet's assessment, based on a "forced decisions analysis," of the four shuttle car power systems as to their relative health and safety is that the exhausting or open cycle diesel is preferred, followed by the closed cycle diesel, the electric cable/motor and the rechargeable battery/motor. The assessment was based on ten parameters pertinent to the health and safety aspects of shuttle cars. Drawing layouts of two typical mine shuttle cars incorporating closed cycle diesel powerplant concepts are included in this report. The performance parameters established for the two concepts are tabulated. A study was made of the logistics involved in transporting and replenishing the consumables needed to operate a shuttle car equipped with a closed cycle diesel. The closed cycle diesel powerplant consumables -oxygen, potassium hydroxide, and diesel fuel - were analyzed as to their compatibility with materials found normally in a gassy coal mine. Spill tests simulating inadvertent leakage of liquid oxygen in a coal mine were performed. A critical evaluation of existing oxygen sensitivity data and the relationship to the use of oxygen on a shuttle car in a coal mine environment is presented.

Jan 1, 1972

By R. Al-Hent, M. Aissa, J. Asfahani

"This paper focuses on determining the favorable geological and hydrogeological conditions for forming uranium occurrences in the Froqlos-Jabal Abou Rabah region, Palmyrides, Syria. Eighty rock samples from this area were analyzed by spectrometric gamma-ray technique to determine the radioactive concentrations of eU and eTh, and of %K. Uranium concentrations in shallow and deep groundwaters were also determined. High uranium concentrations were registered owing to the presence of phosphatic outcrops in the study region. The uranium migration trends and its remobilization were analyzed through the analysis of the behavior of eU, eTh, and their ratio. A positive relationship between eU and eU/eTh, and a negative relationship between eTh and eU/eTh in geological formations of different ages supports the secondary remobilization of uranium. The role of groundwater movement in transportation and redeposition of uranium mineralization is discussed: deep waters are less oxidizing than near-surface waters, and do not appear to have significantly remobilized uranium. This indicates that the source of secondary uranium mineralization is surficial or near surficial, and is mainly related to the leaching of outcropping phosphatic layers.Integration of the results with established radioactive and geological sections reveals four radioactive anomalous zones: north Froqlos, Kherbet Hannora, northwestern flanks of Jabal Abou Rabah (Kherbet Al-Hajar), and the northwestern limit of the Ghuntor depression. The high uranium concentration in north Froqlos is because of its original presence in the phosphate beds and extensive fracturing, which allows groundwaters to penetrate and remobilize the uranium. High uranium concentrations in the other three locations are caused by the presence of evaporites and capillary action, which draws solutions upwards and causes redeposition as surface crusts (gypcrete)."

Jan 1, 2009

By Stephen H. Chung

The blasting performances identified above are considered to be the most practical ones for judging the effectiveness of a design combining explosives / rock / drill pattern. In a total blast design process, productivity relates closely to both fragmentation and heave / displacement of muck. In cast blasting, the more overburden displaced by explosives, the less blasted material there is left to be removed with mechanical equipment such as draglines or trucks. For wall protection and dilution control, estimates of the maximum extent of cracks / damage generated in situ due to blasting will help determine the location for drilling and loading perimeter blastholes.

Jan 1, 1994

By Brian Gar Wingfield

"The introduction of the QuarryMan laser profile system in 1987, along with the development of the corresponding 3-D software, gave a qualified operator pertinent information about dimensions of quarry highwalls, pattern and hole loading design, stockpile profiles, etc . . . Attributes helpful for this endeavor included surveying, computer, and blasting knowledge. Since not all operators had theseskills, a simpler model, the QuarryAce, was designed to look a t highwall dimensions in 2-D view . Al though less sophisticated than the QuarryMan instrument and its software, it is simpler to instruct in its use and has the ability to determine burdens at different depth levels . An in-house user f r i e n d l y computer program was designed to utilize QuarryAce depth vs. burden data . This program was created to enable laser and computer novices to generate information useful to the everyday blaster."

Jan 1, 1992

By Ken Witherly

Modern airborne EM surveys typically acquire more data than is processed or analyzed at the time of acquisition Suitable additional processing can provide more diagnostic information, thereby allowing for more effective ranking and hopefully, follow-up of outcomes

Apr 1, 2005

By T. M. Barczak, S. C. Tadolini

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of “topping off” the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

By T. D. Parris

Within a 30-mile radius of Sudbury, Ontario, the Ontario division of the International Nickel Co. of Canada, Ltd., operates nine underground mines and two open pits. Prior to 1966, ore removal from the underground workings was mainly by scraping, using 125-hp electric slushers in blasthole and caving mining, and 30-hp or less air-operated slushers for fill- method mining. The development and evaluation of low-profile, diesel-powered front-end loaders, designed specifically for underground operations, was followed with keen interest during the period 1964-1965.

Jan 6, 1969

By M. F. Dunn

The objective of this work was to define jet fan performance in d variety of large cross-section underground mine applications and to develop guidelines for thin performance in open airways, dead headings, and multiple face areas. Measurements include common ventilation instruments, continuous recording remote electronic anemometers to measure air velocity, and sulfur hexaflouride tracer gas with chromatograph analysis to determine dilution rates and air recirculation. For open airways the following were determined: Large jet fans are leas efficient in smaller airways, but quite effective in larger open airways for achieving both uniformity end greater air entrainment, when inclined about 10° or elevated. For dead headings the following were determined: The jet fan must be placed against the rib of the heeding closest to the incoming airstream from the crosscut or recirculation will increase. The fan should be placed at the pillar corner to increase airflow. As the fan is moved closer inby, recirculation increases. Larger fans promote recirculation. Inclining fans about 12° improves airflow in large headings. For face areas the following were found: For panels having uncontrolled airflow, the fan should be placed in the incoming airflow, about one pillar inby, and directed diagonally across the faces. For panels having narrower rooms and controlled airflow, the fan should be placed alongside the panel side in the first room so as to direct or intersect the incoming airflow at the next entry or crosscut.

Jan 1, 1983

By J. A. Murray

Maintaining satisfactory air quality in electrowinning tankhouses is problematic and costly, particularly as plant operating current densities have increased. Conventional approaches have not proved completely effective. These include the use of beads, hollow spheres, surfactants and coalescer devices. They require powerful ventilation systems to be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses.

Jan 1, 1996

By A. Patri, D. S. Nimaje

Wireless sensor networks and wireless communication systems have become indispensable in underground mines. Wireless sensor networks are being used for better real-time data acquisition from ground monitoring devices, gas sensors, and mining equipment, whereas wireless communication systems are needed for locating and communicating with workers. Conventional methods like wireline communication have proved to be ineffective in the event of mine hazards such as roof falls, fires etc. Before implementation of any wireless system, the variable path loss indices for different workplaces should be determined. This helps in better signal reception and sensor node localization, and also improves the method by which miners carrying the wireless devices are tracked. This paper proposes a novel method for determining the parameters of a suitable radio propagation model, which is illustrated with the results of a practical experiment carried out in an underground coal mine in southern India. The path loss indices, along with other essential parameters for accurate localization, have been determined using the XBee modules and ZigBee protocol at 2.4 GHz frequency.

Jan 1, 2015

By S. A. Aye

Vibration levels on a variety of equipment in a South African opencast mine were measured in this study. The well-established ISO 2631-1 (1997) standard methodology was used for the computation of weighted root mean square (WRMS) and vibration dose value (VDV). This method was used to evaluate the whole-body vibration (WBV) on a wide range of equipment in the opencast mine using the two main parameters, namely the daily exposure A(8) which is based on the WRMS concept and the VDV which measures shocks. The results obtained show that while the majority of the equipment rendered exposure levels that are below the exposure limit value (ELV), exposure levels on about half of the equipment do exceed the exposure action levels. The study also highlights the importance of shock in the observed responses.

Jan 1, 2011

One of the most significant problems experienced in land reclamation work has been the tendency of earthmovers to over-compact the subsoils and topsoils. The need for extensive subsoil drainage, because of over-compaction, becomes a very expensive exercise and can be attributed to poor planning. The problem has been addressed both at the Waihi and Huntly open-cast mines through the use of low ground pressure machines in the placement of subsoils and contouring. The use of subsoilers working to contour to aerate the soils is essential to integrate both the sub and topsoils so that significant root growth and drainage is established. Waihi's rainfall (approximately 200 mm annually) and light soils create difficulties in preparing for the final seed bed. A noticeable factor in preparation of the growing medium was the reaction of the lime particularly in the subsoils (damp), from a lumpy, quite heavy texture to almost a seed-bed texture within a period of approximately 72 hours. Also the high incidence of stone and debris which was not apparent in the placement of subsoils meant the job became very labour intensive. This will be overcome with the importation of a machine from the USA. All of the rubber tyred tractors used on these projects are four wheel drive in the 6S-aOhp range which for weight distribution and the safety factors allows for good landscaping techniques. Good engineering practices should ensure that slopes of no more than 3:1 be designed, keeping in mind that the long term planning must allow for maintenance and stock management of restored land.  In the preparation of the final growing medium the equipment used included: Caterpillar 05 LPG and blade; three-four wheel drive rubber tyre tractors; Super flow subsoiler; hydraulic twin spinner manure spreader; discs û two types; harrows; MF Seeder; Cambridge Roller and Duncan Rotatiller.

Jan 1, 1991

Three computerised sets of minerals information are being developed by New Zealand Geological Survey in co-operation with the Resource Management and Mining group of the Ministry of Energy: 1. Geological Resource Map: a file of information on the location, geology, geochemistry, production, and potential use of individual occurrences of aggregate, mineral, geothermal, coal, oil, and gas resources. The computer program can be used for search and retrieval of information and the production of maps and tables. The data is being published as a series of 1:250 000 maps with accompanying text and tables. 2. Minerals Bibliography: an index and retrieval system for mineral exploration related; open-file company reports, N.Z. Geological Survey files, scientific research publications and university theses. 3. Minerals WhoÆs Who: an annotated directory of geologists involved in mineral exploration, mining and research.

Jan 1, 1986

By Rudy J. Matetic

Over-exposure to noise remains a widespread and serious health hazard in the U.S. mining industries despite 25 years of regulation. Every day, 80% of the nation’s miners go to work in an environment where the time weighted average (TWA) noise level exceeds 85 dBA and more than 25% of the miners are exposed to a TWA noise level that exceeds 90 dBA, the permissible exposure limit (PEL). Additionally, MSHA coal noise sample data collected from 2000 to 2002 show that 65% of the equipment whose operators exceeded 100% noise dosage comprise only seven different types of machines; auger miners, bulldozers, continuous miners, front end loaders, roof bolters, shuttle cars (electric), and trucks. In addition, the MSHA data indicate that the roof bolter is third among all the equipment and second among equipment in underground coal whose operators exceed 100% dosage. A research program was implemented to: 1) determine, characterize and to measure sound power levels radiated by a roof bolting machine during differing drilling configurations (thrust, rotational speed, penetration rate, etc.) and utilizing differing types of drilling methods in high compressive strength rock media (>20,000 psi). The research approach characterized the sound power level results from laboratory testing and provided the mining industry with empirical data relative to utilizing differing noise control technologies (drilling configurations and types of drilling methods) in reducing sound power level emissions on a roof bolting machine; 2) distinguish and correlate the empirical data into one, statistically valid, equation, in which, provided the mining industry with a tool to predict overall sound power levels of a roof bolting machine given any type of drilling configuration and drilling method utilized in industry; 3) provided the mining industry with several approaches to predict or determine sound pressure levels in an underground coal mine utilizing laboratory test results from a roof bolting machine and 4) described a method for determining an operators’ noise dosage of a roof bolting machine utilizing predicted or determined sound pressure levels.

Jan 1, 2006

By J. Drelich, J. Pletka

Lost foam casting patterns are foamed polystyrene shapes glued together into the shape of the part to be cast and are coated with a refractory material consisting of a mineral mixture and binders. Prior to casting, a significant number of the patterns are damaged and inevitably land-filled. In this study, a process is developed for the recovery of foamed polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and density separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene.

Jan 1, 2001

In the estimation of reserves the known values of the variables of interest from surrounding drill holes are used to compute or estimate the unknown value of the orebody over a given region or at a given point of interest. The classical means of doing this are: 1. The Polygonal Method û where the region is divided into polygons centred on bore holes, each variable is then assumed to have constant value over each polygon. 2. Inverse distance methods, where the variable is assumed to vary linearly with the distance between the known values of the drill holes. 3. Inverse distance squared method û a quadratic variation is assumed for the variables between the bore holes.

Jan 1, 1983

By J. E. Forciea, O. E. Palasvirta, L. G. Hendrickson

AH pilot and commercial plants working with Mesabi Range taconite employ wet magnetic separation. Progress is being made with a dry magnetic process, but this has not yet been applied to taconite except in the laboratory and pilot plants. Flowsheets in all five plants are similar, including multiple stages of grinding, each followed by magnetic separation, which rejects a finished tailing. The flowsheet in Fig. 1 is used in the preliminary and commercial plants of the Erie and Reserve mining companies and in Unit C of Oliver's Pilotac plant. At Erie the desliming operation is omitted. In the Reserve plants two ball mills are used with each rod mill. Pilotac uses flowsheet 2 in Unit A-B and has also tested flowsheet 3. Principal differences in the three flowsheets are the number of grinding stages and the type of roughing. The terms open-circuit roughing and closed-circuit roughing are best defined by the diagrams. Special Test Data Given in Table I: For the Erie and Reserve commercial plants, Table I reflects routine conditions. Pilotac, the experimental plant, has been run with several flowsheets, including those followed at Erie and Reserve's commercial operations. Pilotac data for these last two flowsheets are similar to commercial plant results and are not repeated in Table I; statistics are given, however, for special test conditions. using other flowsheets. when the objective was to 'to extra-grade concentrate, Variations Among Taconites: Although crude ore tributary to these plants is generally classified as taconite, there are important differences in mineralogy and fineness of dissemination.

Jan 1, 1959

Some low grade South Australian iron ores were classified on the basis of their physical characteristics. Ores from Mount Christie and Billeroo are coarse grained mixed ores; Mount Christie ore could be concentrated by gravity or dry magnetic separation at 10 mesh, but Billeroo ore needed to be crushed minus 36 mesh. Ores from Razorback Ridge and Wilgena Hill are fine grained mixed ores; ore from Wilgena Hill could be concentrated by flotation, but poor results were obtained on Razorback Ridge ore. Malcolm Creek ore is non-magnetic and crystalline, and can be concentrated by flotation, but the deposit is small. Ores from Grants Quarries and Peeralilla Hill are nonmagnetic and earthy and could not be satisfactorily concentrated.INTRODUCTIONThe Geological Survey of South Australia has for several years been undertaking a systematic study of the iron ore resources of the State (excluding the Middleback Ranges) in relation to their geology, reserves, and beneficiation. As part of the latter phase of the investigation samples of the ores have been submitted to The Australian Mineral Development Laboratories (AMDL), and it was the study of these samples which provided the material for this paper.The mineragraphic and metallurgical work was undertaken by several officers of AMDL and the results are contained in unpublished reports submitted to the South Australian Department of Mines. Field data published here was obtained from unpublished reports by G. F. Whitten, Senior Geologist, Iron Exploration, of the Geological Survey of South Australia.

Jan 1, 1964

By Chris Bennett, Drupad Desai, Kirit Mevawala

INTRODUCTION The design/build (D/B) philosophy of contract delivery is neither new nor unusual when it comes to at-grade, elevated or high-rise structures. But when it comes to constructing underground facilities, there were no examples to be followed in early 90sin the continental United States or its territories. When DMJM+HARRIS was selected as general architectural and engineering consultant for the Tren Urbano (TU) project in Puerto Rico, one of the requirements of the Federal Transit Administration (FTA) for funding commitment was to use TU as a demonstration project utilizing design/build contract delivery method. Now fifteen years later, New York City Transit (NYCT) has instituted a similar requirement for their first Tunnel Boring Machine (TBM) contract for the Second Avenue Subway. As with most construction mega-projects, lots of things have happened and there were several lessons learned from the TU experience that are now being applied to Second Avenue. Both of these projects require building tunnels and underground transit facilities in heavily traveled corridors of an urban city, in the vicinity of active business and commercial enterprises. To enhance the challenge, there are noise and vibration sensitive and historic urban receptors either over or along both the transit corridors. Column free Tren Urbano station caverns over18 m (60 ft.) wide were built in soft ground conditions within 3.6 m (12 ft.) of the surface under an aging heavy utility corridor, while NYCT tunnels with station structures stretching the limits of rock caverns to 34.8 m (100 ft.), were planned in rocky geology with the presence of shear and fault zones and some mixed face conditions. BACKGROUND During the early period of design/build experimentation, the speed with which the contract procurement packages could be put together enabled the owners to take advantage of the major efforts underway to rebuild the infrastructure that was suffering from post-World War II neglect. Use of design/build for new starts was unheard of and most of the projects were smaller in nature in order to allow the methodology to be tested. Development of functional design packages with the understanding that the D/B

Jan 1, 2005