Search Documents

By Barton G. Stone

"Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole," (Baxter and Parks, 1939)."An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence, the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence."The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling."Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive." (McKinstry, et al., 1948).In an actual orebody, the accuracy of sampling depends not only on the number of samples but also on their proper distribution throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore, it is important to select the places in such a way that all parts of the orebody will be represented."

Jan 1, 2014

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 (PL 109-236, 2006) established the Office of Mine Safety and Health, functioning as the Office of Mine Safety and Health Research (OMSHR) within the National Institute for Occupational Safety and Health (NIOSH) and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued more than 150 contracts focused on worker health and safety. Initial funding for this program was provided by the United States Congress through two emergency supplemental appropriations and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation. Ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website (www.cdc.gov/niosh/ mining/researchprogram/contracts/index.html) and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously (Snyder et al., 2016).External contracts are broadly classified by the following areas:• Communications and tracking.• Emergency response.o Self-escape and breathing air supply.o Refuge alternatives.o Escape and rescue.• Equipment safety.• Fires and explosions.• Ground control.• Mine environmental systems (mine ventilation and atmospheric monitoring).• Worker/workplace health and safety.Contracts are issued under a request for proposal (RFP), through a broad agency announcement (BAA) or under an interagency agreement (IAA). An RFP solicitation includes a specific problem description and a well-defined scope of work to guide the offeror in preparing a bid to conduct the research. Under the BAA several problem areas are described and the offeror develops the scope of work and deliverables for the proposed research. An IAA is very similar to an RFP except it is a contract between two federal government agencies."

Jan 10, 2018

By K. M. Phamotse, A. S. Nhleko

"*Paper written on project work carried out in partial fulfilment of BSc (Mining Engineering) degreeSynopsisLiqhobong Mining Development Company (LMDC) has been experiencing problems with boulders after blasting where the fragment sizes exceed the maximum of 800 mm as per mine standard. As a result, the mine has employed various methods to improve the fragmentation. The goal is to produce a run-of-mine (ROM) feed that does not choke the crusher and cause delays in production. In order to achieve this goal, fragmentation distribution within the fines and coarse envelope must be optimized through effective planning of blasting activities and accurate execution.The mine determined the fines-coarse envelope within which the entire crushing system can handle fragments using Split Desktop software. It is expected that both the predicted and actual fragmentation curves lie within that envelope for optimal fragmentation. The Kuz-Ram model with blast design parameters of 2.6 m for burden, 2.8 m for spacing, and 127 mm hole diameter was used to predict the fragmentation. The results show that the blast design parameters may need altering to achieve optimum fragmentation. Furthermore, the execution of the drilling and blasting may be the cause of the fragmentation problems. The mean fragmentation size (X50) differs greatly, unlike the uniformity index (n)s values which are relatively close to each other (0.6 to 2.2). The mean squared error (MSE) values have a large range. A proposed solution is a modified burden, spacing, and hole diameter. It is concluded that blast design parameters need to be reviewed in order to obtain correct predictions. IntroductionFragmentation has an impact on the mine production cycle which comprises, inter alia, drilling, blasting, loading, hauling, and crushing. Correct fragmentation as set by the plant design is important as it reduces the time lost due to secondary blasting and/or loading difficulties. In this paper we analyse blast results at Liqhobong Mining Development Company (LMDC) in Lesotho for a period of six months. This project was undertaken to observe the trends from the blasts and to identify whether any discrepancies exist in the overall blast information. The period under study included 16 blasts."

Jul 1, 2019

Mine waste and mine reclamation are topics of major interest to the mining industry, the government and the general public. This publication and its companion volume are the proceedings of a conference held in Pittsburgh, April 19-21, 1988. There were nine sessions (50 papers) that dealt with the geochemistry, hydrology and problems of mine waste and mine water, especially acid mine drainage. These comprise Volume 1. The nine sessions (43 papers) that dealt with reclamation and restoration of disturbed lands, as well as related policy issues, are included in volume 2. Volume 2 also contains the ten papers that pertained to control of subsidence and mine fires at abandoned mines. Poster session presentations are, in general, represented by abstracts; these have been placed in the back of both volumes.

Jan 1, 1988

By R. G. Shen

The relation curve of strain and acceleration is presented in this paper. The steel pipe pile of 609.6 mm in external diameter driven by IDH-45 diesel motor hammer on the esturial shoal of Yangtze River. The ultimate bearing capacity of pile is analyzed by one dimensional wave equation and the effect of computational parameters of the equation is discussed.

Jan 1, 2010

By Brendan Henry

The Canada Line is a 19km long automated light rapid transit system with 16 stations in Vancouver, BC, Canada. The Concession was awarded to InTransitBC to design, build, partially finance, operate, and maintain the system for 35 years. The project must be complete by November 2009 to be ready for the 2010 Winter Olympics to be held in Vancouver and Whistler, BC. The bored tunnel section consists of 2.45 km of twin bored tunnel and 3 stations. The station work is limited to the excavations and temporary support necessary to facilitate the bored tunnel works. A joint venture between SNC-Lavalin Constructors Pacific and SELI (SSJV) has recently completed the design and construction of this section. Work for the bored tunnel commenced in November 2005 with shoring and excavation works for the tunnelling operations pit that will become Olympic Village Station and will be completed in the spring of 2008. The tunnels were driven with a 6m diameter Earth Pressure Balance Tunnel Boring Machine (EPBM) and lined with 250mm thick, 5.3m diameter precast concrete segments. Seven hundred and fifty meters of each tunnel were driven through glacial and interglacial deposits of sand, silt, and clay with granitic boulders. The paper discusses the challenges faced in negotiating these soils which contained unforeseen geological conditions. These conditions were overcome by developing a systematic approach to Risk Management that included thorough risk assessments, regular risk management meetings with the participation of two of the world?s leading EPBM experts, Professor Eisenstein and Professor Kovári, and by the ability of the construction team to effectively analyze and mitigate problems.

Jan 1, 2008

By W. Tom Witherspoon

Many Engineers are skeptical and cautious about skin friction factors for the portion of drilled piers where temporary casing is used. This has led Texas engineers in many cases to eliminate skin friction values for the cased section, which necessitates deepening the drilled shaft to compensate for the loss in the cased section. This paper has provided field test data that supports inclusion of skin friction in the temporarily cased hole section as a contributing factor in total axial capacity as comparable to open hole shafts of the same diameter. Reasons for the resultant friction values are provided including; remolding of the cased clay section and the increased pier circumference necessitated by the oversized casing required for adherence to the engineers shaft diameter specification.

Jan 1, 2009

Mount Read is 'situated in the county of Montagu, on 'the west coast of Tasmania, about 20 miles inland from. Remine in an easterly direction, 15 miles northerly from Mount. Lyell, and 30 miles south-east from Mount Bischoff, and is one of the mountains forming the west coast range; it rises to a height of 3890 ft. above sea level.About eleven years ago the first mineral section was taken up on Mount Read by a Hobart company, known as the Mount Reid Silver Mining Company, consisting of 25,000 shares its holding consisted of one section of 80 acres, held under mineral lease. Prospecting was carried on for some months under great disadvantages, as all supplies had to be carried up the mount from Dundas, a distance of nine miles, on men's backs, until a pack track for horses was made.The track rises 2500 ft. in the first five miles, and then falls 200 ft. from that point to the mines, which are at an altitude of 3000 ft. above sea level, and at a point about two miles westward from the summit of the mountain, approximately midway between Mounts Read and Dundas.

Jan 1, 1901

By Robert Stefanko

The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given elsewhere (1,2). The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania.

Jan 1, 1969

Experiments in the bolting of a mine roof were commenced at Elrington Colliery on the South Maitland Coal Field early in 1949, following the appearance of an article in the American publication, "Coal Mine Modernisation Year Book" 1948. Prior to this, although bolting had not been used in the maintenance of satisfactory roof conditions, the principle of roof bolt anchorage had been illustrated in instances such as the hanging of a trolley locomotive power wire using an expanding shell type of bolt anchorage, or the insertion of an eye bolt with a split and wedge, as used to suspend a rope block over a winze being sunk in a metalliferous mine.The experiments at Elrington Colliery were the first efforts in this country to supplement the work of timber supports under a mine roof with systematic placement of roof bolts.Following the series of experiments at Elrington, full scale bolting was commenced at that Colliery in a trackless mobile section in April, 1950.The obvious success of the system at Elrington indicated that it might also be a success in the support of weak roof strata immediately overlying the workable section of the Victoria Tunnel Seam at John Darling Colliery.The system was commenced at John Darling Colliery in April, 1951, in one mechanical section on the Victoria Tunnel Seam, and the scope was gradually widened until by December, 1952, ail'six mechanical units then operating on this seam were working under bolted roofs.

Jan 1, 1954

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anorthosite layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spineI-bearingmeta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, and Ni liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

The only simple sulphide mineral of antimony of importance is stibnite, SbS3, containing 71·8% antimony when pure. It is lead-grey, has a densityof 4·5 to 4·6 and melts at 546°C. It is both friable and sectile (Hardness 2 on Moh's scale) and, as a result, slimes very readily during milling.It is commonly associated with pyrite and arsenopyrite other minerals occurring with stibnite in minor quantities are chalcopyrite, galena, and scheelite. The latter mineral occurs in sufficient quantity at the Yellow Pine Mine, Stibnfte, Idaho, to justify the production of a scheelite concentrate.Stibnite mayor may not contain gold. Other minerals such as pyrite or arsenopyrite may contain gold. At Wiluna at the main mine nearly all the gold is asociated with arsenopyrite the stibnite being almost free from gold, whilst at the Moonlight Mine both arsenopyrite and stibnite carry gold.The mineral, tetrahedrite, which is a complex sulphide of copper and antimony; must also be considered an economic source of these two metals.Part of the copper may be replaced by iron, zinc; silver; or mercury, whilst part of the antimony is often replaced by arsenic.CLASSIFICATION OF ANTIMONIAL GOLD ORESFor the purposes of this paper antimonial gold ores may be conveniently classified as follows: CLASS 1. Ores from which a satisfactory gold extraction may be obtained by fine grinding, followed by cyanidation and which contain insufficient antimony to justify tIie production of an antimonial concentrate.CLASS 2. (a) Ores in which a satisfactory gold extraction may be obtained by straight cyanidation, but which contain sufficient antimony to justify the production of an antimonial concentrate.CLASS 2. (b) Ores from which the gold extraction by straight cyanidation is unsatisfactory. This type of ore requires the production of an antimonial concentrate for reasons which will be considered later.In deciding whether an ore belongs to class 1 or 2 (a) it should be remembered that the normal price of star antimony is about £1.00 sterling per ton and that the value of each 1% of antimony recoverable as metal is worth about £1 per ton.The antimony content of antimonial gold ores is liable to be considerably...

Jan 1, 1944

By Sharpin P. C

The countercurrent gas-solid heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temperature distributions through the drier have been calculated. Although the calculations rest on several simplifying assumptions, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating conditions on the rate of drying of the briquettes which controls the strength of the char produced. The analysis shows why a limitation was reached in the improvement of char strength in the pilot plant in 1961 due to the performance of the drier and a prediction is made of a way in which the limitation could be overcome.

Jan 1, 1966

By K. Meyer

"INTRODUCTIONThe David Bell Mine Concentrator started production in April 1985. A staff of twenty-seven people operate and maintain the concentrator. The crew is grouped into the following main areas.16 Operators6 Assaying/Metallurgy/Refining/Clerical4 Maintenance people2 SupervisionOperating highlights of the following unit processes will be discussed in detail:Screening and ThickeningPre-aeration and CyanidationCarbon-In-Pulp Gold AdsorptionCarbon Handling andGold RecoveryFor a complete description of the concentrator, refer to the papers by: (1) C.V. Sibbald, Teck-Corona's Hemlo Mill, October 1984, (2) R.A. Ford, The David Bell Mine at Hemlo, From Exploration to Production, November 1987. For operating details of the grinding circuit and effluent treatment plant refer to papers by: (3) T.G. Smith, SAG Mill Experience at The David Bell Mine, October 1988, ( 4) AN. Veltmeyer, The Effluent Treatment Plant of The David Bell Mine, January 1989.TRASH AND CARBON SCREENSTrash ScreenThe vibrating trash screen is inclined at 5 degrees and is clad with a 28 mesh stainless steel cloth which is changed monthly during the SAG mill liner replacement/inspection shut down. Other screen openings and configurations have been tried and the screen has been by-passed to change the cloth ""on the fly"". These attempts resulted in fibres (usually wood) to report to #1 Carbon-In-Pulp (CIP) tank, where the fibres are trapped in the CIP launder screens, and downstream carbon handling screens causing serious blinding problems. The trash screen in a Carbon-In-Pulp (CIP) or Carbon-In-Leach (CIL) gold mill removes fibres before they:are reground in the ball millsaturate with gold bearing leach solutionplug launder screens in CIP or CIL tanksplug carbon circuit pipe screenstherefore the trash screen is best placed ahead of the thickener."

Jan 1, 1989

By P Cameron

MetPlant conferences have focused on ensuring mining projects are well designed then optimised to operate safely and effectively at the top end of world’s best practice to ensure shareholders are not just happy but delighted. This assumes the MetPlant was built right the first time. However, reality is, too often Plant Metallurgists (PlantMets) find after commissioning they are faced with the expensive task of correcting errors or modifying shortcomings to achieve product quality at name-plate capacity, i.e. get it right the second time. Why do companies spend good money to engineer an excellent feasibility study then allow “wise men” remote from the project team to impose cuts in budget and schedule, often under the guise of value engineering? Since mining is full of uncertainties, such actions can increase the risks of failure with the result that some MetPlants do not work well. Can PlantMets influence the remote wise men who often are also imposing the rules for lending and the required returns to appreciate the uncertainties of mining and their associated risks then let the project team get it right the first time? PlantMets can negotiate with the wise men from the outset of the project and bring them into an outer layer of the team where they can understand the risks then share responsibility and accountability to achieve the common goal of building a MetPlant which works well the first time and deliver the forecast profits. Since shareholders are not in the business to make losses they appoint a Board of Directors to deliver the best outcomes for the shareholders. Thus the Board should seek effective advice on the risk reward implications from the PlantMet before making their decisions.CITATION:Cameron, P, 2015. Do all metplants work well? PlantMets can ensure they do, in Proceedings MetPlant 2015, pp 2–9 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Paul Averitt

The coal-bearing rocks in Iowa occur in an arcuate belt across the central and southern parts of the State (fig. 1) at the northern end of the Western Interior coal field. Coal beds of minable thickness are sporadic throughout this area and are mined principally in the three districts indicated by dark shading on the index map, although coal occurs also in the areas indicated by light shading. The coal is mostly of high-volatile C bituminous rank in all parts of the State. SURFACE FEATURES The coal-bearing rocks in Iowa are concealed for the most part by a covering of glacial drift ranging in thickness from a few feet to several hundred feet. This covering has been dissected to form a gently rolling upland, rising from an elevation of 466 feet at the mouth of the Des Moines River to about 1,200 feet in Calhoun County in the central part of the State. The local relief, however, rarely exceeds 150 to 200 feet.

Jan 1, 1949

By Suresh K. Bhatt, Christopher Mark

Fatalities caused by highwall/spoil bank failure in the surface mines, coal and non-metal, increased to an alarming rate of seven during 1999. To determine the causes of slope failure and successful mining practices, the National Institute for Occupational Health and Safety undertook a study. The study included: 1.A review of accident statistics; 2.A review of Federal and state mining laws pertaining to surface mining; 3.A literature review, and; 4.Mine visits. The study emphasized surface mines in the states of West Virginia, Ohio, and Pennsylvania. The review of a decade’s accident statistics using the mine Safety and Health Administration’s (MSHA) database showed that approximately 40% of all ground control related incidents reported to MSHA occurred in just four eastern states: Kentucky, West Virginia, Pennsylvania, and Ohio. The comprehensive literature search provided a historical perspective of highwall stability issues. Eleven mines we visited to obtain data on their mining practice or design. Commodities included coal, sandstone, and limestone. Based on the visits, five case studies were developed to represent typical mining methods and effective ground control practices used in eastern surface mines. Benching was found to be a common technique to reduce the overall highwall slope angle. Decking in the softer zones, such as shale, proved useful in controlling damage due to blasting.

By P Hunger, H Günter, F Heinicke

High pressure grinding rolls (HPGR) have been used for more than 20 years to grind iron ore pellet feed. Besides coarse comminution (crushing), where HPGR are installed upstream of the ball mill, there are numerous flow sheets where HPGR are used after ball milling and dewatering for re- or finish grinding.There is a clear growing interest in grinding of pellet feed with HPGR during the last few years. In addition to their known advantages of low specific energy consumption, high availability, low steel consumption and improved pelletising processes the lower environmental load (reduced or no water consumption) became a strong driving factor for the application of HPGR in pellet feed grinding.This growing demand increases the interest in better understanding of the HPGR grinding process with fine iron ore concentrates. One of the most important process parameters is the moisture content of the feed material which influences the performance of the HPGR enormously. The HPGR can react to fluctuations of the fresh feed properties to a certain degree by adjusting grinding force and roller speed. Nevertheless, there are limitations by the physics of the compression process and the capability of water absorption by the concentrate. The capability varies for different concentrates and different specific surface areas. This fact has to be considered during engineering of the beneficiation plant.The paper focuses on the influence of feed moisture content on the HPGR performance in view of throughput, increase of Blaine number and process stability on the basis of numerous pilot plant tests, modelling results and industrial experiences.CITATION:Heinicke, F, Günter, H and Hunger, P, 2017. Influence of feed moisture on high pressure grinding roll pellet feed grinding, in Proceedings Iron Ore 2017, pp 187–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Tae-kyeong Yeu, Jong-Choi, Cheon-Hong Min, Hyung-woo Kim, Jae- Won Oh, Sup Hong, Minuk Lee, Sung-Soon Kim, Chang-Ho Lee, Ki-Young Seong

"Collecting mineral resources from the seabed using a seafloor crawling robot is the firststep in the mining operation. The second-step is lifting the collected ore up to the water surface. For lifting through a riser pipe, prevention of pipe clogging (flow assurance) and economic and eco-friendly up-transferring is of the utmost concern.During collection of mineral ores, the production rate can be highly variable because of the variability in the distribution of the mineral deposit, variations in seafloor topography, fluctuations robot speed, and variations in performance of the mining robot, etc. Direct transfer of the collected ore to the riser pipe might cause unpredictable and serious problems such as over-loading of the lift pump, reduction in the life of the equipment, pipe clogging, severe increase of down-time, critical damage of equipment, further propagation of damages, and total failure after all.As a counter measure to these potential problems, a buffer station has been adopted, which is capable of storing the collected ore for a certain time and simultaneously regulating the transfer of the ore into the riser pipe. A pilot buffer has been developed by KRISO/KIOST (see Fig. 1)."

Sep 1, 2014

By T. Fabritius, L. Hekkala, J. Härkki

The Outokumpu steel belt sintering technology is used for manufacturing chromite pellets that are charged into smelting furnace for ferrochromium production. Hot air is blown through the moving bed of raw pellets. Direct temperature and flow measurements are difficult to do in the bed of a real scale belt sintering process. Therefore, a tested and reliable mathematical model would be a valuable help for optimising operational parameters of the process and designing new constructional improvements. The aim of this work is to present a mathematical model that calculates the gas flow and temperature distribution in the bed of pellets and the atmosphere. Computational fluid dynamics program FLUENT is used to calculate the gas flow, composition and temperature of the gas in the sintering bed during processing. Energy equation for the bed, containing the effects of evaporation of water and oxidation of carbon and iron oxide, will be added to the model to obtain the temperature of the pellets. The porous media model used for pressure drop calculations in the bed is shortly discussed. A comparison between CFD-calculations and experiments with a pilot scale batch-sintering reactor are also presented. The final model can be used as an engineering tool when developing the process and the equipment further. Different designs can be easily tested with the model and the effects of the changes to the flow pattern and temperature distribution can be studied.

Jan 1, 2004