Search Documents

By S. M. Spottiswoode

Crush pillars are widely used in mine workings on the Merensky Reef in the Bushveld Complex to prevent panel collapses. Crush pillars are expected to fail as or soon after they emerge from the face and failure should occur non-violently. Unfortunately, violent failure occurs frequently and is said to be the main cause of seismicity associated with mining of the Merensky Reef. Recent work by Napier, Malan, and du Plessis has shown that limitequilibrium quasi-static models are able to simulate pillar failure using three states of strength of rock in pillars, namely intact, residual after failure, and decayed strength after later time-dependent (viscous) weakening. We have previously introduced an additional state of strength to account for the dynamic failure that results in seismic events, and found that this approach could be used to generate synthetic seismic catalogues similar to observed seismicity for deep-level gold mines, where seismicity takes place mostly on advancing faces. The less brittle seam material of the Merensky Reef, compared to the brittle quartzites and lavas of the Witwatersrand reefs, results in little or no face bursting and is modelled with an assumed plastic strain of some 0.005 over an effective stope width of 2 m before failure. When this plastic yield is surpassed, we allow the reef to fail ?seismically?. We show that synthetic seismic catalogues modelled in this way have some of the features of observed seismicity. Analysis is greatly facilitated using our custom-built software that reads the mine?s survey data into a database and presents results in an interactive graphical form.

Jan 1, 2014

By Lyne Côté, Jose Adante

"The Caribou underground mine, 50 km west of Bathurst, the Restigouche open-pit mine, another 30 km west and the concentrator located at the Caribou mine site resumed operations in July 2007 after a nine year shutdown. The Caribou operations achieved commercial production on Jan 1. By June, 2008, all metallurgical targets had been achieved or surpassed with the production of lead and zinc concentrates assaying approximately 50% Zn and 45% Pb respectively with recoveries exceeding 80% for Zn and 70% for Pb.The deposit features very fine-grained massive sulphide mineralization, which in the past has proven difficult to process. ISA Mill Ultra Fine Grinding Technology in combination with conventional flotation technology is used to process these complex oresSeveral modifications arising from experience gained from past operations, an extensive research project at Lakefield Research and post startup flow sheet and reagent alterations have been employed to achieve this break through performanceThis paper describes the design, start up and optimization of the Caribou operations including the many challenges faced including the flotation of mineral particles with K80s ranging from 35µm to 8µm.HISTORICAL BACKGROUNDThe Caribou massive sulphide deposit was discovered by Anaconda geologist Cam Cheriton in 1959. Anaconda initiated an extensive underground exploration and discovered a super gene copper blanket which was developed into a small open-pit mine-mill operation that ran from 1970 until the depletion of the copper ore in 1974. East West Minerals, an Australian public company, purchased the mine in 1986 and operated for only seven months producing a single bulk lead-zinc concentrate. In 1995, Breakwater acquired the Restigouche Open pit and Caribou underground deposits. Breakwater began milling operations in July 1997 but Caribou Mine failed to commercialize production, and the company decided to shut it down in August 1998, because of declining metal prices. The mill was plagued by mechanical and design problems, but deficiencies in metal recoveries prevented the operation from reaching desired levels."

Jan 1, 2009

By Tom Shumka

"All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it be every six months to every three years. The inspection frequency depends on gear tooth condition, and the objective is to ensure the operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection or dye penetrant examinations rely heavily on operator interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combining combined eddy current array (eca) and alternating current field measurement (acfm) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.INTRODUCTION In order to gain a fundamental understanding of the evolving operational and production behavior of a piece of machinery over a specified time period as part of an effective condition monitoring program, a robust data collection process must be firmly established and adhered to. To be effectively implemented within an organization, a condition monitoring program must have support of not only the maintenance, production and engineering staffs, but also executive management support to ensure successful roll out to realize the maximum productivity of the machinery and subsequent cost-savings. One of the key elements of a mineral processing facility that use gear driven SAG Mills as a primary stage for grinding solution, is the integrity of the critical gear unit that drive the mill. For the maintenance team, condition monitoring on the gear unit is crucial for preventative maintenance. A catastrophic failure in the critical gear unit would require a minimum of ten days to replace the gear set, depending on the damage occurred. This, of course, would only be applicable if the client had a spare critical gear set in inventory. If a gear set had to be ordered, it could take from four months to two years to receive a new gear set. For example, in 2007, there was a global backlog of these types of gears sets resulting in a two year delivery. The maintenance costs associated with a catastrophic failure of this type would easily cost in the millions."

Jan 1, 2012

By R. Reed von Gal

The majority of zinc strip produced in the world today is cast on the Hazelett twiri-belt continuous casting machine. Ten of these machines are currently operating worldwide, and one machine is under construction for the People's Republic of China. The caster, which was first patented in 1947, was originally developed for aluminum and copper alloy casting. In the early 1960s, the design was expanded into zinc casting and within ten years the industry had essentially converted from casting and rolling ingots to twin-belt continuous casting with in-line rolling. The casting process employs two parallel, moving. water-cooled belts as the major mold surfaces. Together with two strings of side dam blocks, the design offers a four-sided moving mold which produces a continuous strip or bar. This paper will cover a bit of, the history, as well as the current technology surrounding this high production process for zinc strip production.

Jan 1, 1990

By K A. Campbell, K A. Rodgers

The Plumduff sinter occurs at Whenuaroa, near Puhipuhi, approximately 30 km north of Whangarei. It is one of three residual sinters in the southern portion of a mid- to late-Pliocene geothermal system. The deposit consists of many large sinter breccia boulders, including rudrocks (coarse breccias), scattered around the flanks and summit of the small conical hill of Plumduff. Three types of sinter breccia occur: (i) rudrocks consisting of large, angular to sub-angular clasts of layered sinter up to 0.8 m across, as well as smaller clasts of sinter (20 - 100 mm dia), and fragments of stromatolitic structures; all clasts are supported in a matrix of microcrystalline, transparent to translucent to milky quartz; (ii) fragments of layered angular to irregularly mottled sinter of white to grey or bluish hue supported in a translucent to opaque silica matrix; (iii) smaller, matrix-supported breccias with clasts both partially surrounded and/or penetrated, by a clay-like weathering rind, and sinter conglomerates with rounded to oblate clasts. Three principal types of fabrics constitute the bulk of the sinter: (i) stromatolites, including columnar, palisade and filamentous networks, showing progressive silicification, in fenestral, tufted to clotted fabrics; (ii) peloids and pisoids; (iii) plant-rich facies in which various silicified plant species occur in a silica matrix. All fabrics have counterparts in hot spring deposits in the Taupo Volcanic Zone formed at temperatures from 75¦C to 35¦C. Also present is steam-condensate-produced alteration: kaolinite and alunite as well as boulders of quartz lattice texture. Cinnabar only occurs in sinter on the north and south central slopes of the hillside. No quartz veins or geyserite were recognised.

Jan 1, 2001

Most types of nuclear power reactors use uranium dioxide fuel. Power reactors using natural uranium dioxide fuel are of special interest to countries such as Australia that have their own uranium supplies. A wide range of uranium dioxide powders can be fabricated and the ideal one flows readily, presses without the need for binders or lubricants, sinters to the required density and gives low reject rates at all fabrication stages. Sinterable uranium dioxide is usually produced via the ammonium diuranate route.The Australian Atomic Energy Commission is aiming to demonstrate production of nuclear grade uranium dioxide from Australian concentrates, improving technology where possible. Details are given of the dissolution, solvent extraction, precipitation, filtration, drying, and· calcination-reduction steps. Solvent extraction from sulphate media is also under study with a view to developing a process to produce a nuclear grade product at the mine treatment plant site.

Jan 1, 1970

By F. W. Smith

To determine whether preheating coals before carbonization would improve the coking properties of the coals, particularly the weaker coking coals, 3 coals, 1 each from Illinois, Kentucky, and Pennsylvania, and a blend of the Illinois with a Pocahontas coal were preheated before testing for coking properties in the Bureau's BM-AGA pilot oven. The effects of preheating on the chemical and physical proper-ties of the coals and on the yields of carbonization products and strength of the coke produced from the preheated coals were determined, as were also the effects of bulk density, gaseous atmosphere, and residence time during preheating. Most benefit from preheating was found with weaker or oxidized coking coals, whereas the more strongly coking coals and blends showed little effect. Direct charging of preheated coal to the coke oven without cooling gave better coke, increased yield of tar, and decreased yield of gas. INTRODUCTION Although 94 percent of today's coal production comes from fields east of the Mississippi, the Eastern States have only about one-third of the Nation's recoverable reserves. West Virginia, which now produces more than any other State, has much smaller reserves than Utah, Colorado, and Wyoming.5/ However, the manufacture of iron and steel in Western States, which has increased greatly since World War I, is handicapped by the scarcity of high-grade coking coals, such as are plentiful in the Appalachian region. Unless a practical method of improving the cokemaking property of local coals is developed, ferrous metallurgical industries in the West must continue to use inferior coking coals and to pay high shipping charges for better coals.

Jan 1, 1958

By C. B. Manula

Bituminous coal mining in the United States is currently experiencing a period of rapid growth which began in the early 1960's. Future demands are conservatively predicted to rise to 700 million tons by 1980 and to anywhere between 1 to 3 billion tons by the turn of the century. This means a continuous expansion of coal production by a factor of at least two can be expected before the end of the century. Over the last few years, production from underground mining has decreased; yet it is about 50% of the total coal output. In the absence of any discovery of near surface coal deposits, and even after conceding that some deeper deposits can be surface mined with changes in technology it can be reasonably assumed that coal production from underground will continue to play an important part in solving the energy crisis.

Jan 1, 1975

By Richard J. Stoehr

In his time on earth, man has mined about 93.3 kt (3 billion oz) of gold. About one-half of this has been produced in the past 35 years. Roughly one-third of this gold is held as reserve in Central Banks. One-third held is in personal reserves. And one-third is held as jewelry or other fabricated products. The world per capita availability of mined gold is increasing. There are many forces shaping gold's future. Gold currently has a favorable exchange ratio. This is encouraging many new gold mining developments. Production is increasing and new recovery techniques are surfacing. The use of gold in the financial markets is increasing in some unique ways. And gold is again fulfilling its role as a universal money, making its future predictable. Gold Today Man is currently mining gold at the rate of about 1.4 kt/a (44 million oz per year). This adds about 1.5% of newly mined gold to the total supply each year. This production plays a small role in the pricing mechanisms since much of the 93.3 kt (3 billion oz) mined is available to the market in some form. The 31.1 kt (1 billion oz) held by central and international banking

Jan 11, 1984

Ledcap Pty Ltd has developed two software tools for assisting in the determination of life-of-mine (LOM) trucking requirements. The first tool generates haul paths and the second calculates truck travel time over these paths. The two step approach allows the paths to be viewed and if required edited, to better represent the actual site haul routes.The first tool automatically creates haul paths between the mine bench and the dump. To do this the user supplies a master haul route and a scheduled block model. The master haul path and the block model are interacted to create multiple haul routes, one for each pit/dump bench pair in each scheduling period. Each path carries with it a record of the scheduling period it represents and the dry tonnage hauled over the path in that period.The second tool calculates truck travel time over the path. Data from the manufacturer's rimpull and retarder curves are used to calculate accelerations and speed over each segment of the haul path. As the paths are derived from digitised representations of mine haul routes the path f les often have over a hundred segments. This detailed representation of the haul route allows the software to automatically adjust speed for different radius corners and accurately simulates the changing accelerations over the gradient changes that occur in real life mine ramps. Rolling resistance can be specified at a global level, at a segment level and at a period level. This allows rolling resistance to be changed seasonally as well as spatially.Life-of-mine trucking studies attempt to calculate an accurate answer from extremely variable inputs. This paper will detail the features of the two software tools and how the tools provided in the software can assist the mine planner to have greater confidence in their life-of-mine trucking requirements and the subsequent production capacity inputs to their scheduling calculations.

Dec 6, 2010

By Eugene H. Skinner

The 7-mile Flathead Tunnel, located in the central Salish Mountains of northwestern Montana, was constructed between 1966 and 1969, With the contract awarded April 19, 1966, drill and blast tunnel excavation began September 30, 1966, and was completed June 21, 1968, in 488 tunnel-driving days, Peak advance was 66 feet per day. On June 27, 1969, all tunnel concrete lining was completed. Average wall and arch concrete placing rates exceeded 1,700 cubic yards daily, with nearly half of the concrete placed during a severe winter season. Major cost savings in concrete tunnel lining were achieved through a value engineering clause in the contract. Achieving consistent results and high rates of placement in concrete lining ranked equal to ground control in overall tunnel problems. Ground control problems exceeded expectations and were of continual concern throughout excavation, One support collapse in the tunnel and one portal slide condition developed during construction. Critical surface geologic exposures were largely obscured; only a portion could be accurately projected underground, An instrumentation program to gather basic data on rock defamation near the heading face for support purposes was a pioneering effort. The Flathead Tunnel was placed in service on November 7, 1970.

Jan 1, 1974

By David G. Almond

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations having large SAG mills fitted with variable speed drives. Problems associated with effective operation of this equipment has created the need for better operator knowledge of mill load behavior and the need for new instrumentation capable of providing accurate information about load movement and composition. This paper discusses two performance enhancing instruments available to address these needs.INTRODUCTIONThe economic demands of new mining projects has resulted in increased equipment sizes and this is particularly evident in milling where there are now many SAG mills operating in the range of 28’ – 40’ diameter with installed powers of 8 – 22 MW. These mills are designed to process very high capacities of ore daily2 and the variable characteristics of many of the deposits mined results in the need to vary the mill speed during processing to cater for the changes in ore hardness. Mill speed changes often result in operational problems associated with high-energy impacts striking the mill liners reducing energy efficiency as well as degrading the grinding media through breakage, accelerating liner wear and in extreme cases even breaking liners. These operational problems have given rise to the need to have instruments aimed at providing operators with accurate information in real time about the load composition and movement within SAG mills.The original concepts for operating SAG mills were derived from past experience of operation of conventional fixed speed ball mills. However, the relatively stable conditions that applies with fixed speed and constant ball charge in ball mills supports theoretical approaches to the grinding process based on energy calculations such as Bond’s Work Index concept. Later a set of parameters Si and Bij were used for describing load kinetics, but all of these methods neglect the details of load movement and how the energy is actually used inside of the mill. It is now commonly accepted as a basic rule that SAG mills grind by impact whilst ball mills grind by attrition and consequently SAG mills are designed and operated to generate a large amount of impacts by the cataracting load without paying sufficient attention to where these impacts are actually occurring. Many mills are operated on the basis that as long as the mill is consuming the expected power there is little attention given to the class of bodies using this energy and this often results in the inefficient use of energy."

Jan 1, 2005

By R. S. Dean

This report, the second of a series of annual reports of the Metallurgical Division to be released in this form covers the fiscal year July 1, 1935, to June 30, 1936. The technological work of the division is performed by sections. Thus, an efficient organization is provided to prosecute the various problems under investigation, and a logical system is set up for presenting the material contained in this report.

Jan 1, 1937

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

By Bruce Jago, Joe Zhou, Chris Martin

"From the perspective of metallurgical processing, gold ores can be classified into free-milling and refractory ores. Their extractive metallurgy are largely driven by mineralogical factors such as: gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide mineral structure etc. Gold process mineralogy helps address issues and problems related to gold ore processing. It provides useful information on process selection, flowsheet development, recovery improvement and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore. This paper will provide a broad review of gold process mineralogy and the techniques available, and use case studies to describe how they can be used together, to provide the complete picture of gold process mineralogy in an ore. Examples will be used where applicable.INTRODUCTIONSince the early 1980’s, a great deal of work has been done in the characterization of gold ores, particularly refractory ores (Gasparrini, 1983; Wang, 1984; Hausen, 1985; Haines, 1986; Henley, 1989; Chryssoulis et al., 1990; Wang et al., 1992, 1994; Kojonen, 1999; Simon et al., 1999; Hong et al., 2000; Pals et al, 2003). Process mineralogy has come into its own as a respected inter-discipline in the fields of mineralogy and metallurgy – a subject that occupies an important place in both research and industry. As the free-milling gold ores are being depleted and more refractory ores are being discovered and processed, gold process mineralogy receives more and more attention from both the mineralogist and metallurgist as it helps to solve various problems encountered during gold ore processing. Steadily rising gold prices are also stimulating the need for gold process mineralogy due to the increasing demand for and production of the yellow metal. At SGS Lakefield Research, gold process mineralogy studies are conducted routinely on all types of gold ores and mill products to assist in a wide variety of metallurgical projects. This paper will briefly discuss the gold ore types and gold mineralogy, review the common mineralogical factors affecting gold extractive metallurgy and the techniques available to gold process mineralogy, introduce the procedure employed at SGS Lakefield Researc"

Jan 1, 2004

By Paul Meadows

The Buckrange reservoir, Stephens field, Ark., is approaching the economic limit of production under present operating conditions. Over 100 million barrels of oil remaining in the reservoir will not be recovered by primary producing methods. The Bureau of Mines, in cooperation with the Arkansas Oil and Gas Com-mission, made the petroleum-engineering study presented in this report to aid operators in evaluating secondary-recovery possibilities in the reservoir and in planning secondary-recovery programs if their initiation is decided. The Stephens field, in Columbia, Nevada, and Ouachita Counties, Ark., is about 12 miles northeast of Magnolia, Ark., and 15 miles west of the Smackover field. Surface elevations in the area average about 240 feet above sea level.

Jan 1, 1956

By J. Wagner, P. Eger, G. Melchert

In 1991, LTV Steel Mining Company decided to close an open pit taconite mine in northeastern Minnesota, using a passive treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. Over 50 million metric tons of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages, and prior to closure annual median concentrations ranged from 1.5-50 mg/L. Copper, cobalt and zinc are also present but are generally less than 5% of the nickel values. Median pH ranges from 5.0 to 7.5, but most of the stockpile drainages have pH greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential a stockpile had to produce acid drainage, the lower the permeability of the capping material required. Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to over 90% for the plastic liner. Five constructed wetlands have been installed since 1992, and have removed 60-90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1% of those for an active treatment plant. Since mine drainage problems can continue for over a hundred years, the lower annual operating costs should pay for the construction of the wetland treatment systems within seven years.

Jan 1, 1999

By Jorge Castillo

This paper presents a dynamic analyses of heap leach pad stability under high phreatic levels and various levels of seismic loading. The dynamic analysis were conducted as fully non-linear two dimensional analyses with fully coupled liquefaction triggering using the Fast Lagrangian Analysis of Continua (FLAC) computer code. Also, the geotechnical parameters, appropriate earthquake record selection and modification, model calibration, numerical analyses and results are discussed.

Sep 12, 2005

By Donald J. Ninteman

This Bureau of Mines publication is a literature study of the problem of spontaneous oxidation and combustion of sulfides in underground mines. It summarizes the present-day hazards, process mechanisms, and prevention and control techniques of this growing problem in underground mines. The iron sulfides generally have the greatest tendency to oxidize, particularly pyrrhotite. The presence of moisture and oxygen is essential for the oxidation reaction. Highly fractured sulfides, when found with timber or combustible refuse in slowly circulating air, pose the most serious fire hazard. Quenching with water is effective in quickly dealing with local hot spots, but ventilation at high flaw rates is the most effective and economical means for long-term prevention and control.

Jan 1, 1978

By B Putland, I Lovatt, D Schwann, A Cervillin

The Mount Carlton project in Queensland's North East sits on a high-sulphidation epithermal style deposit rich in gold, copper and silver. Mt Carlton is an open pit mining operation with ore processed using a primary crusher, single stage SAG mill and flotation to produce a concentrate for sale. Orway Mineral Consultants (OMC) was involved in the original design of the comminution circuit and the project was commissioned in late 2012, with first concentrate shipped in March 2013. When Evolution sought to optimise the project in 2015, OMC was invited to assist by undertaking a circuit review to identify opportunities for the optimisation. During 2016, the Mt Carlton site team implemented the optimisation strategies developed in conjunction with OMC. These included reconfiguring the SAG mill discharge arrangement, reducing the average ball diameter and allowing the mill to operate at higher speed and under more autogenous conditions. Cyclone operation was changed to constant pressure and the vortex finder size was decreased. The combined strategies improved energy efficiency and allowed higher SAG mill power utilisation. The additional power has been used to increase throughput by 2.4 per cent while achieving a 27µm reduction in product size (P80) to gain downstream recovery improvements. The reduction in grind size has been achieved with only 6.8 per cent increase in specific energy consumption because of a 6.5 per cent increase in grinding efficiency. The circuit product size is also notably more consistent due to the improvements made to the cyclones, providing benefit to the downstream flotation circuit. A significant decrease in ball consumption was also gained, saving hundreds of thousands of dollars a year in operating cost.This paper will discuss the circuit design, start up and will detail the changes made during the optimisation and why these were successful.CITATION:Putland, B, Lovatt, I, Cervillin, A and Schwann, D, 2018. Mount Carlton comminution circuit design, start-up and optimisation, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 517–528 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018