Search Documents

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

By R. Curtis

To achieve compliance with 2015 EPA Tier 4 Final regulations, which permit only around 10% of Tier 3 particulate matter (PM) and NOx emissions, a number of technologies are being implemented. Use of a fuel borne nanoparticle combustion catalyst reduces the level of PM and unburned hydrocarbons exiting the combustion chamber, alleviating the burden on downstream exhaust after-treatment systems. The impact of an iron-ceria combustion catalyst (GO2) on carbon oxidation kinetics and on diesel engine emissions is presented. The iron-ceria nanoparticles catalyze carbon oxidation at lower temperatures and increase the oxidation rate by a factor of 18 at 400 °C. Engine tests on a generator powered by a John Deere Model engine and field tests on a Cummins ISC 330 tractor truck and CAT 3508B propulsion engines are presented. Use of GO2 resulted in a reduction in PM10 (particulate matter under 10 um) emissions of up to 26% and a hydrocarbon emission reduction of up to 41%. NOx emissions did not increase in these trials and the amount of change depended on engine type. Application of this fuel borne technology for emissions reductions in mining equipment offers significant benefits.

Feb 27, 2013

By Boris Belenky, M M. Graevsky, R I. Semigin, A E. Frantov

"In the mining industry, most of stripping and rock fragmentation is performed by blasting. The academician N.V. Melnikov has projected that blasting methods would be used to crush 20% of soft rocks and 80435% of medium and hard rocks. Thus, the volume of blasting will continue to increase.This is especially true for electrical blasting, since this method has a number of well known advantages, and in some cases (e.g. for underground blasting in coal mines) it is the only acceptable method."

Jan 1, 1995

By Stephenson. E. L.

"INTRODUCTION In the spring of 1942 a series of magnetometer surveys on deposits of black sand underlying Pleistocene raised marine terraces along the coast of southwestern Oregon was nada by the Division of Geophysical Exploration of the Federal Bureau of Mines in cooperation with the Oregon Department of Geology and Mineral Industries. A few preliminary tests had been made in the same area in May 1940 and December 1941.The sands contain fine gold and metals of the platinum group, and, beginning in 1852, extensive, but spasmodic mining and exploration have been done for these precious metals. There are many old placer, mines and prospects, although for the most part the yield of the metals has been small. The sands also contain other minerals of potential value, including ilmenite, magnetite, garnet, zircon, and particularly chromite, and the wartime demand for domestic chromite resulted in extensive testing and development of the known deposits. The purpose of the magnetometer surveys was to determine the efficacy of, magnetic methods in tracing and outlining these known deposits and in prospecting for new ones. The field work was done between March 17 and May 29, 1942, by the author assisted by W.W. Paulsen of the Oregon Department of Geology and Mineral Industries."

Jun 1, 1945

By Paul T. Alexander

After evaluating preceding studies and designs of lightweight supports, ESD selected the all-hydraulic and the hydromechanical concepts for detailed design and fabrication. Further analysis and testing showed that the all-hydraulic design was economically justified and met all the crucial engineering, manufacturing, and design criteria identified during the evaluation phase. Following Bureau of Mines approval of the detailed design, four all-hydraulic support models were fabricated. Once functional and structural testing was successfully completed, 40 additional units were constructed and distributed for in-mine testing. The units were very well-liked by all three demonstration mines. The wide- spread interest in supports for seam heights greater than 8 feet led to expansion of the design data package. ESD designed four basic models to cover the new height range, but no hardware has yet been fabricated for the new design.

Jan 1, 1982

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By Rogerson R, Queen L

The petrology and age of mid Cretaceous to Palaeogene marine volcanics may provide important clues to the palaeogeography of the period, particularly for tectonic elements and events outboard of the Papuan Basin. This initial survey of known marine volcanics of this age reveals a paucity of reliable data on isotopic ages, geochemistry and syngenetic mineralisation on virtually all units. Existing data allows a tentative subdivision of known marine volcanics into either MORB-like early Palaeogene rifts/ marginal basins, early Palaeogene ensimatic arc rocks overlying ?Late Cretaceous and Palaeogene fore-arc/marginal basin crust, late Palaeogene ensimatic arc rocks, and mid to Late Cretaceous ensialic rift rocks. Due to lack of data, some units are difficult to classify into these categories.

Jan 1, 1991

By Raj K. Rajamani, Sanjeeva Latchireddi, Dave Plummer, Stieger. Julius

"The Cortez SAG mill liner design was recently modified to improve the mill operating energy efficiency. In addition to the expected benefits, the design change unexpectedly played a significant role of verifying the proposed grinding circuit expansion for the Cortez Hills project as well as illustrating current SAG mill bottlenecks. This paper will discuss the evaluation that addressed operator and maintenance observations, historical PLC data, and “crash stop” observations to calculate charge motion, packing between lifters, and slurry transport through grate and pulp lifters. The performance of the new shell and discharge end liner design will also be discussed as well as their role in the possible grinding circuit expansion.INTRODUCTIONCortez Gold Mines commenced operation in 1969 with its Mill #1 rated at a nominal 2,000 tons per day. Mill #1 was a conventional rod mill/ball mill circuit followed by an 8-stage CIP circuit. In the early 1990s the Pipeline deposit was discovered and subsequently Mill #2 was built to process the increased ore volume. Mill #2, commissioned by mid-1997, was a nominal 10,000 tons per day SABC circuit followed by an 8-stage CIL circuit for oxide gold ore. Operating and commissioning details of this plant have been published elsewhere (Powell, 1998). By late 1998, there was not enough ore volume to support both mills so the smaller, higher operating cost Mill #1 was put under its current care-and-maintenance status. A simplified flowsheet of the current mill is shown in Figure 1."

Jan 1, 2007

By D Craw, K A. Hunter

Deposits of the metalloids arsenic and antimony occur in quartz veins of mesothermal hydrothermalsystems in the South Island as arsenopyrite (AsFeS) and stibnite (Sb2S3). Arsenopyrite and stibnite occur in natural exposures in gold-mining areas, and additional arsenopyrite and stibnite have been exposed to the atmosphere by mining activity. At present the drinking water limits for dissolved As and Sb are 10 ppb and 3 ppb respectively. Sampling and analysis techniques are critical to determination of metalloid concentrations at these low levels. Endeavour Inlet in the Marlborough Sounds is an historic mining area (late 19th Century) with elevated As and Sb in waters emanating from mineralised rocks. Waters running out of abandoned adits have concentrations of As and/or Sb up to ppm levels. Natural waters have high Sb and low As, and the As levels increase markedly where anthropogenic activity has exposed rock. Changes in Sb/As ratio could potentially be used to quantify the anthropogenic component of metalloid mobility on mine sites on the 100-year time scale.

Jan 1, 2002

By Jiayao Wang, Jian Chen, Leiting Shen, Hongyang Wang, Zeping Cao, Ziru Wang

Large amounts of by-products, including coal gangue, circulating fluidized bed (CFB) slag, and coal fly ash (CFA), are generated during mining, washing and burning of high alumina coal (HAC). The stockpile of these by-products of HAC will cause the pollution of air, water and soil. Meanwhile, the unbalanced regional distribution of bauxite and alumina production has been a critical challenge for the sustainability of world alumina refineries, especially for China. Therefore, economical extraction of alumina from by-products of HAC not only resolves the environmental pollution problems caused by stockpile but also decreases the dependence degree of import bauxite in China. Considering the fact that powder alumina can only be produced by alkali methods, the alkali extraction of alumina from by-products of HAC is summarized in this paper. Based on the formation process of by-products of HAC, the principle, research status, and problem of existing methods were analyzed and discussed, as well as the forecast of research trend. The analyses indicate that simplex recovery of alumina from byproducts of HAC generates large amounts of leaching residue (red mud) with difficulty for disposing, while comprehensive extraction of alumina and silica meets the research trend for clean and high-value utilization.

Aug 25, 2023

By Matters C. W

THE following paper embodies the present practice and the results of past experience in the survey departments of two of the leading Broken Hill mines, the Central (Sulphide Corporation Ltd.) and the Broken Hill South S. M. Co. N. L.The authors intend to limit the scope of this paper to a consideration of office methods, as much has recently appeared in technical literature concerning field work, both surface and underground. Special reference may here be made to a valuable paper on 'Mine Surveying' by H W Gartrell, in Vol XIII of Transactions, in which the author gives considerable attention to field work. Moreover, much of the office work described in current literature is American, and sometimes not suited to local conditions, being ·often exceedingly elaborate and demanding a large staff of assistants. It is believed that the methods of recording information described in this paper are sufficiently simple and flexible to be adapted to most Australian mines. Brief acknowledgement must be made to the work done by Americans, who have raised mine surveying to the position of a separate profession, instead of being merely an unimportant branch of land surveying.

Jan 1, 1912

The whole of the iron ore required by the Broken Hill Proprietary Company Limited at the Newcastle Steel Works, and Australian Iron and Steel Limited, at Hoskins' Kembla Works, is drawn from the Iron Knob, Iron Monarch, Iron Prince and Iron Baron deposits situated in the northern part of Eyre's Peninsula, South Australia.The Iron Knob and Iron Monarch deposits are near the township of Iron Knob, approximately 42 miles W.S.W. of Port Augusta, whilst the Iron Prince and Iron Baron deposits are some 18 miles due south from Iron Knob, in another group of leases, the adjacent township being known as Iron Baron.The ore mined at Iron Knob, Iron Monarch, Iron Prince and Iron Baron is conveyed on the Company's 3ft. 6-in. gauge tramway to Whyalla, on the western side of Spencer's Gulf, approximately 45 miles south by west of Port Augusta whence it is shipped to Newcastle and Port Kembla.SHORT HISTORY.The establishment in South Australia of the lead smelting industry at Port Pirie, Dry Creek and Port Adelaide in the...

Jan 1, 1937

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006

By Tacio Ferreira

How state-of-the-art software, data analysis and communication applied to drilling and blasting techniques have have allowed quarries in the Midwest of the United States to improve results downstream

Feb 1, 2020

By S. Frimpong

The cable shovel excavator is used for primary production in many surface mining operations. A major problem in shovel excavation is the variability of material diggability, resulting in varying mechanical energy input and stress loading of shovel dipper-and-tooth assembly across the working bench. This variability has a huge impact on the shovel dipper and tooth assembly in hard formations. In addition, the geometrical constraints within the working environment impose production limitations resulting in low production efficiency and high operating costs. A potential solution to the above problems is the application of an intelligent cable shovel excavation(ICSE) technology. In this paper, dynamic models of the cable shovel excavator are developed with numerical examples. These models form the basis for developing dynamic shovel simulators for an intelligent shovel excavation technology. The dynamic equations are developed using the Newton-Euler techniques. The path trajectories for efficient excavation, dynamic velocity and acceleration profiles, and dimensioned parameters for optimum feed force, torques and momentum of shovel boom-bucket assembly are modeled and used for efficient excavation. The optimum digging forces and resistances for the cable shovel excavator are modeled and used to predict optimum excavation performance.

Jan 1, 2003

By Roger Frank

"Abstract After noting the importance of standardization for piles, the European system is described (execution, tests and design, etc.). Some important aspects of Eurocode 7 are outlined (like the role of pile load tests). Finally, the calculation methods in the recent French standard for the design of piles following Eurocode 7 are shortly addressed.Importance of standardization for piles Like for other fields of geotechnical engineering, pile engineering is a complex art. For piles, the challenges are particularly numerous and many things must be mastered properly: - the soil investigation must be serious and adequate (for instance, deep enough!);- the choice of the pile type and the assumed behaviour must be assessed in order to reach a safe and economic design of the overall foundation;- the execution itself (construction and/or installation) deserves special attention and must follow strict state-of-the art rules.The geotechnical engineer, in charge of the design of a pile foundation, must have in mind the parameters linked to the variety of soils, of soil conditions and of pile types. A wide range of strong environmental issues are also to be considered: minimum disturbance during the execution processes, long-duration friendliness of the “inclusions” into the ground (to avoid pollution of the soils and waters, for instance) and respect of the neighbouring structures.Pile engineering plays in a world which is constantly moving and progressing: constructions expand in new difficult areas, actions on piles are more and more important, new execution techniques of piles are developed, research into the complex behaviour of pile foundations has no end, etc. Our views on how piles and group of piles really work are constantly evolving!"

Jan 1, 2014

By Clayr Alexander

Stillwater Mining Co. (SMC) is engaged in developing, extracting, processing and refining palladium, platinum and associated metals (PGM)from the J-M Reef. This geological formation is located in Stillwater, Sweet Grass and Park counties in southern Montana. Associated byproduct metals include rhodium, gold, silver, nickel and copper. SMC’s current mining operations are near Nye, MT. The company is currently developing a second underground palladium and platinum mine, the East Boulder project, about 21 km (13 miles) west of the Nye operations. A 5,650-m (18,550-ft) tunnel is required to gain access to the ore-bearing horizon (J-M Reef).

Jan 1, 1999

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

Whether the microscopic bubbles generated by the high energy dissipation and high feed-slurry velocities in new flotation cells are stable in solution and what roles they play in particle collection are of great interest for the flotation of fines. Experimental work has shown that, with fast flow of liquid through an orifice, stable microscopic bubbles can form in flotation systems by hydrodynamic cavitation in the absence of gas supersaturation. The minimum flow rate at which bubble formation is initiated varies from 8 to 15 m/s, depending on the design of the cavitation tube, which is within the range of feed slurry velocities of some newly developed cells. Feed aeration enhances the formation of micro-bubbles by hydrodynamic cavitation. The study suggests that the fast flotation kinetics of some new cells may be attributed in some degree to the formation of microscopic bubbles

Jun 21, 1905

By Barnard Foo

Topics of Discussion ?Location ?Production & Mining Operation ?Mineralization ?Mining Method ?Rock Mechanics Issues ?Ground Control Problems ?Numerical Analysis ?RockmassBehaviour ?Conclusions & Recommendations ?Discussion

Feb 1, 2008