Search Documents

By J. A. Kost

The contract objective was to evaluate the effectiveness of available dust-control technology for double-drum shearers. Eight underground surveys were conducted to evaluate drum design, drum spray nozzle locations, ranging-arm sprays, water quantity, wetting agents, and cutting techniques. The final report is made up of eight dust-control technique reports, each discussing, details of the individual mine surveys.

Jan 1, 1985

By P. N. Lategan

Mining companies are challenged with increased difficulty in delivering capital projects on schedule and within budget. In 2005, PricewaterhouseCoopers global review of major capital projects in the mining industry only 2.5% of projects could be defined as successful when assessed across the four critical dimensions of scope, cost, schedule and business benefits. Thus 97.5% of major mining capital projects were not successful according to the criteria PricewaterhouseCoopers used. Normally if a project fails on all these criteria it indicates scope creep. Scope creep refers to the change in a project's scope after the project work has started. As a result, the projects drift away from their original design, timeline, and budget, and as a consequence destroy business benefits. The major reasons for scope creep are poor change control and the lack of proper front end loading. Change control and front end loading are based on project processes in the planning and monitoring & control process group of the Project Management Body of Knowledge1 (PMBOK). This paper will focus on key factors to consider during project scheduling/planning with special reference to cost and schedule (using Microsoft Project as a tool although the principal is universal)

Jan 1, 2009

By Robert T. MacMillan

A process has been developed in the laboratory and expanded to semi-pilot-plant scale for recovering titania, iron, and byproducts from two types of titaniferous iron ores. A reducing roast with coke and soda ash followed by grinding and magnetic separation produced powdered iron and slag from which titania and byproducts were recovered by H2SO4 decomposition. Based on the steps tested on a. semi-pilot-plant scale supplemented by the results of the laboratory investigations, enough data are available to make a balanced flow sheet. Combined data from the laboratory and semi-pilot plant indicated that 85 to 9O percent of the titania content of the ore was recoverable and that approximately 90 percent of the iron could be recovered as a metallic-iron powder. Tahawus magnetite from the Maclntyre mine at Tahawus, N. Y., was successfully treated as follows: (1) The ore was roasted at 1,050° to 1,080° C. with carbon and soda ash, thereby reducing the iron to metal sponge and retaining the titania in the slag. (2) The metallic iron was separated, after wet grinding, by magnetic or gravity means. (3) The slag fraction was air-roasted at 850° C. and leached with NaOH to recover Na3VO4. (4) The leached solids received a dilute-H2SO4 leach to remove interfering impurities, chiefly Na2O and SiO2. (5) Titania was dissolved from the leached solids of step (4) by a H2SO4-bake followed by a water leach. (6) Titania was precipitated by seeding and boiling the resulting solution. The spent liquor was used for the dilute-H2SO4 leach in step (4). The following scheme was found to be technically feasible for recovering other byproducts of the process. (1) The gelled filtrate from the dilute-acid leach step was washed and dehydrated to produce a commercially acceptable silica gel. (2) The wash liquor containing sulfates of Na2O, Al2O3, Fe2O3, and TiO2 was combined with the highly alkaline filtrate from the wet-grind and metallic iron-separation steps, precipitating iron and titanium hydroxides, which were separated for special treatment. (3) Anhydrous Na2SO4 and Al2O3?3H2O were recoverable from the alkaline filtrate from step (2) by evaporation and carbonation, respectively, and the barren liquor was recycled to the magnetic-separation step.

Jan 1, 1952

By Manuel Gomez, V. F. Parry, John B. Goodman

"INTRODUCTION The need for an accurate and precise analytical method for determining moisture in coals of high water content has been recognized by the coal industry as well as the fuel technologist. Interest in this particular phase of coal technology extends back to the early work of German investigators on the brown coals of Central Europe. Studies by these workers led to the establishment of a direct immiscible liquid-distillation method 4/ as the accepted moisture determining technique in European laboratories. Direct moisture determining methods, those methods that utilize various techniques to drive off the water from a given sample of coal and either collect the water in a calibrated receiver or selectively trap the water driven off in a suitable absorber, have found little favor in the United States. They have been treated merely as research tools.5/ The problem of moisture determination in low-rank coals of the United States has not been given much consideration because such coals contribute only about 2 percent of the total United States production. With renewed activity in low-temperature carbonization and with the growth of interest in coal and coal-tar hydrogenation, the American coals of lover rank containing 20 to 40 percent bed moisture will be subjected to extensive investigation. If the low-rank coals of the United States are to be accurately appraised, the need for qualitative and quantitative analytical proceeded becomes more pronounced. These coals, especially the lignites of Texas and North Dakota, are highly susceptible to oxidation, a process that proceeds to a greater or less extort when low-rank, high-moisture coals are treated by oven-drying methods. The extent of this atmospheric oxidation has been described and evaluated by numerous workers. 7/In many respects, the problem of moisture determination in low-rank coals, those found in the United States and the high-moisture coals of Central Europe, is similar. Conversely, the problem of moisture determination assumes a different aspect when the coals of the eastern and the middle-west sections of the United States are considered. Present methods, the loss in weight gravimetic-type procedures, serve adequately to test these low-moisture coals. The determination of moisture in coals containing 20 to 40 percent water should be approached from a direct method rather than from an indirect gravimetic-type procedure because of the oxidative tendencies of these coals and the demonstratrated inability of a loss-in-weight technique to remove all the water in a given sample of coal."

May 1, 1953

By Maxwell Gensamer

Jan 1, 1960

By Licheng Zhou

The use of aquatic plants for the removal of heavy metals from wastewater has gained high interest. In this study, batch experiments were conducted to evaluate the adsorption of copper ions in aqueous solution by P. pectinatus L. under various conditions of contact time, initial pH of the solution, metal concentration and adsorbent dosage. The results showed that the maximum adsorption amount of copper ions by P. pectinatus L. was 22.60 mg/g when the initial copper ions concentration was 98.41 mg/L at pH 4.5. The Langmuir and Freundlich models were used to describe the adsorption equilibrium of copper ions on P. pectinatus L. and the adsorption followed the Langmuir isotherm. The adsorption kinetic was well-fitted with pseudo-second-order sorption equations.

Jan 1, 2009

By J. P. D. Strydom

The transmission of excessive vibration to the human body can cause physical stress that may result in crippling pain or permanent disability. Rock drills are known to transmit high levels of vibration that are difficult to attenuate through conventional approaches to vibration isolation. However, it can be shown that once the ISO frequency weighting has been applied, most of the vibratory effect of the rock drill?s motion is concentrated at the drill?s operating frequency. This observation opens the way for utilizing a concept known as vibration absorption, aimed at attenuating the rock drill?s vibration. In essence this entails using the inertia of a secondary vibratory system to counteract the motion of the handle. This article documents an investigation into the use of such an absorber for attenuating rock drill vibration and demonstrates the feasibility of such an approach. A mathematical model of such an absorbing handle was developed and used for design studies. Based on these investigations an experimental prototype model was manufactured and tested. A significant reduction in vibration levels could be achieved.

Jan 1, 2002

By G J. Lyman

In sampling a process stream, conventional sampling theory deals only with the variation of the analyte content and neglects the impact of the variation in the mass flow on the sampling variance, whether the sampling regime is time-based or mass-based. This is an obvious simplification of the real state of affairs and it is worthwhile to study this impact via simulation.With a facility to simulate large (long) random functions having some thousands of points in the function and the ability to impose covariance functions on the mass flow and analyte variations, such a study is possible. It is also possible to evaluate the impact of correlation between analyte content and mass flows.This paper describes a limited study of the variance increase due to mass flow fluctuations over the usual sampling variance due to analyte variation during the sampling period. The bias in the sampling result is determined for specific modes of correlation. Simulation methods are used as they are the only means by which a sampling result can be compared to the true assay for the lot; in the physical circumstances of mineral process analysis, it is never possible to determine the true process stream assay.CITATION:Lyman, G J, 2017. The impact of the weighting error, in Proceedings Eighth World Conference on Sampling and Blending , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By D Craw, L C. Kerr, P Wopereis

Gold placers in the Nokomai and Nevis valleys are dominantly Quaternary in age. They occur mainly in western tributaries of the upper Nevis, eastern tributaries of the middle and upper Nokomai, and in the trunk valleys themselves. Placer gold in both valleys is dominantly a-phase Au-Ag-Hg alloy. Au-Ag alloy is absent or rare in most of the deposits, except in the lower Nokomai. Alpha-Au-Ag-Hg alloy is typically coarse-grained (up to 2 cm), angular, and rarely flattened or folded. Crystalline texture, quartz intergrowths, and psuedo-hexagonal crystal-pluck cavities are common. Fluvial transport distance predicted from the maximum Flatness Index ofAu-Ag-Hg alloy particles is typically less than 10-20 km. Coarse (up to 2 cm) cinnabar is commonly associated with the Au-Ag-Hg alloy, and both were probably derived from hydrothermal sources in western tributaries ofthe upper Nevis and eastern tributaries of the upper Nokomai. Minor secondary Au-Ag-Hg alloy occurs locally in the lower Nokomai, where it coats or cements detrital a-phase Au-Ag-Hg and Au-Ag alloy particles. Au-Ag alloy dominates over Au-Ag-Hg alloy in the lower half of the lower Nokomai alluvial plain and gravel of a raised channel incised into semischist basement adjacent to the plain. The Au-Ag alloy is rounded and commonly flattened and folded. Crystalline texture, quartz intergrowths, and pluck cavities are rare, and a fluvial transport distance of 25-40 km is estimated from maximum Flatness Index ofAu-Ag alloy particles. The Au-Ag alloy, three types of gamet, magnetite, clinozoisite and well foliated schist boulders in the abandoned channel are not found in the pumpellyite-actinolite facies bedrock in the Nokomai. These components were derived from greenschist facies schist and sedimentary sources in Otago, many tens of kilometers north of the Nokomai catchment. They were transported to the Nokomai either in Wakatipu Glacier till or fluvio-glacial outwash that entered the valley via Nokomai Saddle, the confluence with the Mataura, or both.

Jan 1, 2000

By Ewan Selers, Gary Cavanough

Drilling automation technology is well advanced and automated drill rigs are in use at a number of operating mines. This is not the case for the other drill and blast processes due to significant technical challenges to overcome. These challenges, with regard to the current “on bench” practices, include placing the initiators, loading the explosive and connecting up the initiation system. Although difficult, these challenges will be solved with engineering advances.

Jan 1, 2016

P&H MinePro Services Canada is supplying Syncrude Canada three more of its model4100BOSS electric mining shovels. The shovels will be delivered during 2003. Syncrude’s oil sands operations already use five P&H shovels. The first 4100BOSS shovel was commissioned at Syncrude’s operation in northern Alberta, Canada in October 2001. The unit loads more than 9 kt/hr (10,000 stph) of unblasted oil sands. Since it began operation, the 4100BOSS has shown a 28% production increase over the four P&H 4100TS shovels also on site.

Jan 1, 2003

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By S. P. Godby, S. P. Sharples

Wind-tunnel tests were carried out of the conditions under which nuisance dust particles (100-1 000 micrometres) become entrained by wind. A laser entrainment monitoring system (LEMS) was used, and was found to provide an accurate means of assessing nuisance dust emissions from a surface. Accurate determination of the threshold entrainment velocity of dusts using the LEMS gives a baseline against which the performance of dust control techniques can be evaluated. Minerals tested included coal, petroleum coke, limestone, sand and pulverised fuel ash. Pilot field trials of a portable wind tunnel equipped with the LEMS have been successfully completed, providing a means of validating laboratory results in the field

Jun 19, 1905

Single particle breakage tests have been used by a number of researchers to investigate some salient features of the complex comminution process. The characteristics of the common single particle breakage tests such as single impact, double impact and slow compression tests are examined and the results from these tests are compared. A comparison of the results from single particle breakage tests with grindability and ball mill tests is given. Application of the results from single particle breakage tests to modelling industrial comminution processes is described. The necessity for further research into single particle breakage tests to develop a simple but comprehensive technique for estimating the breakage characteristics of ores is discussed.

Jan 1, 1986

By Yi Luo

In the study of the topographical effects on surface movement due to underground longwall mining, the factors that affect the incremental horizontal displacements are identified using 10 collected cases. Based on this study, the angle of surface natural slope is the major contributor to the incremental horizontal displacement while the total movement is also playing an important role in some cases.

Jan 1, 1996

By S Lal, S Rost, Q Williams, K Collerson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Shoshonite suite (absarokite-shoshonite-banakite) and adakite-hosted epithermal Au deposits are a feature of circum-Pacific magmatism. Fijian examples include Tavua (Emperor) and Tuvatu on Viti Levu. New discoveries of shoshonite suite and adakite-hosted epithermal Au mineralisation have been made in the southern Yasawa Islands and in central-northern and central-western Viti Levu. The Fijian shoshonites define four NE–SW trending suites. The oldest is the northern 7.9–5.0 Ma Yasawa suite, followed by the 4.7–3.5 Ma Sabeto–Tavua–Rakiraki suite in northern Viti Levu, the 4.7–4.2 Ma Yanuca–Vatulele suite approximately 20 km south of Viti Levu and the 3.4 Ma Astrolabe suite approximately 75 km further south. Shoshonite suite lithologies with 3.8–3.0 Ma ages also occur in the Lomaiviti islands between Vatu-Cake and Moala, to the east of Viti Levu, defining a trend oblique to the NE–SW shoshonite belts. Seatura, a 3.3–2.8 Ma ocean island basalt (OIB) volcano, sits at the northern end of the Lomaiviti trend shoshonites. Trace element/isotopic chemistries indicate that shoshonite arc magma genesis involved the melting of a hydrated supra-subduction zone mantle wedge and also a lower mantle-derived plume (OIB) component. The upwelling plume provided heat for melting and possibly Au enrichment. Accessing the melt generation zone associated with the plume required a slab conduit or window. Such slab windows form by tearing during subduction or occur at slab edges. Adakites form by plume-induced slab melting. The four NE–SW Fijian shoshonite suites are interpreted to occur in back-arc extensional zones above a slab window (tear) that migrated southward during rollback of the New Hebrides–Vanuatu subduction zone. The plume (Seatura OIB) that is interpreted to have caused mantle wedge melting and formation of the Lomaviti trend shoshonites was focused along the interface between the north-dipping Vanuatu–New Hebrides subduction zone and the west-dipping Tonga subduction zone, which we have seismically imaged at approximately 400 km depth. Our model ‘cracks the metallogenetic code’ for shoshonites and adakites and has regional and global implications for Au exploration.CITATION:Collerson, K, Lal, S, Williams, Q and Rost, S, 2015. Cracking the metallogenetic code for Fijian epithermal gold mineralisation , in Proceedings PACRIM 2015 Congress, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Dean Workman

Located in downtown New York City, this project necessitated an innovative conveyor design for successful muck removal. This paper will discuss the technical challenges and engineering solutions of the muck transport system which consists of every commonly recognized version of a belt conveyor. The elaborate system includes a TBM conveyor integral to the back-up system, a wall-mounted extensible conveyor, a crown-mounted transfer conveyor, a floor-mounted fixed-length conveyor, a pocket-belt vertical conveyor, three cascading overland conveyors, and one radial stacker. The most challenging design element was an over-land conveyor featuring a box truss for muck transportation over Northern Boulevard while simultaneously going under the Queens Plaza railroad viaduct. An overview of the project is provided along with the following topics: developing final plans from the proposal concept, interfacing with existing works, communication with the joint venture, and complying with local regulations.

Jan 1, 2008

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999