Search Documents

By A. V. Tarasov

The natural resources of lead and zinc are primarily constituted by polymetallic and lead-zinc ores. Beneficiation of these types of ores to produce standard nonmetallic concentrates inevitably results in an increase in the loss of base and precious metals with tailings. An improvement in the grades of lead and zinc concentrates can be achieved by re-cleaner flotation, but it results in production of intermediate products (middlings) to which substantial amounts of lead, zinc, copper and precious metals report. Without an appropriate technology for treating such intermediate products, the recoveries of valuable constituents from lead-zinc ores would remain unsatisfactory. A process has been developed in the Gintsvetmet Institute for processing of polymetallic intermediate products produced at the ore beneficiation plants. This process is based on electrothermic smelting to produce lead bullion containing precious metals, commercial-grade copper-lead matte and high-zinc slags (up to 15-20% Zn) from which zinc can be extracted by slag-fuming or Waelz process. Tests have indicated that the recovery of lead from intermediate products into lead bullion and matte is about 83-85% and 13-14% respectively (the total recovery is 97-98%), while copper recovery into the matte and zinc recovery into the slag is 90-92% and 95-96% respectively. Precious metals (about 96-97%) report into the lead bullion.

Jan 1, 2006

By Jinxing Ji

The thiosulfate lixiviant system for leaching of gold has been under extensive investigation for nearly two decades and consists of ammonium thiosulfate, copper and ammonia. There are several challenges with this system. The occurrence of ammonia must be taken into account from a health and hygiene aspect in the workplace, and also from an environmental perspective with significant levels of ammonia and copper in the tailings. Copper accelerates the leaching rate but causes excessive thiosulfate degradation. A new lixiviant system that has been investigated consists only of sodium thiosulfate without copper and ammonia. Gold leaching is carried out in an enclosed reactor with slightly elevated oxygen overpressure and temperature. Extensive leaching experiments were carried out to minimize thiosulfate degradation and polythionate formation while maximizing the gold extraction. For the preg-robbing carbonaceous ore sample tested, gold leaching was essentially complete within six hours and the thiosulfate consumption was lower than in the typical ammoniacal thiosulfate system. The gold thiosulfate complex in the pregnant leach solution was found to be quite stable under ambient conditions. This new leaching system has the advantages of being more environmentally friendly, has a shorter residence time, lower thiosulfate consumption, lower oxygen consumption, and is easier to control.

Jan 1, 2003

By J. Antonio Barrera-Godinez, S. E. James, J. Sun

The solvent extraction separation of iron from a zinc sulfate medium using DEHPA was investigated. After loading, the ferric ions were reduced in the organic phase using metallic zinc. The ferrous ions produced could be easily stripped into a sulfate solution with pH values in the range of 1.4 to 2.0. The small, laboratory scale pilot system used in this study allowed for continuous cycling of the organic and strip aqueous solutions. It was possible to establish and evaluate a series of steady state conditions under selected operating paiameters. The effects of processing parameters such as solution chemistry, flow rates, zinc metal loading and pH on iron recovery and efficiency were also evaluated. Under proper conditions, it was possible to remove about 5 g/L iron from the organic phase in one stage and to produce a concentrated iron sulfate strip solution containing ferrous ion concentrations in the range of 90 to 130 g/L. Preliminary feasibility tests were also made on electrowinning metallic iron from the strip solutions and crystallizing ferrous sulfate as a means of making a marketable iron product.

Jan 1, 2000

By A. F. Otero

During the electrowinning (EW) of copper significant quantities of highly toxic vapors (acid mist) are produced due to the liberation of oxygen at the cathodes. Acid mist affects the health of operators, the environment and plant infrastructure. Acid mist can be decreased to acceptable levels by a combination of physical means (e.g. ventilation, plastic spheres over electrolyte) and chemical surfactants that decrease the surface tension of the electrolyte, modifying the way oxygen bubbles burst at the surface of the electrolyte. However, only few chemical surfactants are compatible with electrolytic applications, and they are not always used due to their high costs. This paper describes the application of a novel surfactant of natural origin (commercial name Mistop®) to suppress acid mist in copper EW process. Mistop® contains triterpenic saponins derived from the Chilean quillaja tree Quillaja saponaria Molina. The product is non-toxic, and poses no risks to the environment or to EW operators. Mistop® was tested at a laboratory, pilot plant and industrial scale in the world?s largest copper EW production plant at Radomiro Tomic (RT), CODELCO, Chile. At a Mistop® dosage of 8-9 ppm, acid mist decreased below the value accepted by Chilean regulations (< 0.5 mg/m3). At this dosage, Mistop® represents and economical alternative to chemical surfactants, and it is currently industrially used at RT.

Jan 1, 2003

By A. V. Tarasov

The high efficiency of autoclave processes is attributed to the fact that they are suitable for processing of refractory raw materials, have low capital costs and high productivity, ensure integrated utilization of the feed materials, produce innovative saleable products, completely eliminate any air emissions, provide low-waste or waste-less technology, as well as mechanization and automation of production processes. In the immediate future, it might be expected that autoclave processes will find use on commercial scale for production of heavy non-ferrous metals in combination with other processes (hydrometallurgical, upgrading, sorption and solvent extraction, electrolytic, etc.) to ensure: -Integrated processing of refractory ores and concentrates (pyrrhotite, zinc, copper-zinc, lead-zinc, nickel-cobalt, copper, pyrite); -Production of metallic powders of base metals as commercial products (copper, cobalt, nickel, etc.), composites on their bases, final products and saleable salts. Processing technologies incorporating autoclave processes, especially, at the stage of liberation (chemical upgrading) of minerals, are characterized generally by high overall recoveries of valuable constituents significantly exceeding recoveries common for conventional pyrometallurgical processes (for some elements by several tens of percent). An example is processing of low-grade refractory pyrrhotite concentrates using autoclave liberation of feed material under pressure of a new reagent, i.e., sulfur dioxide. The use of sulfur dioxide ensures a significant improvement in the recoveries of non-ferrous metals and platinoids to sulfide concentrate and smelting of the latter increases the capacity of the smelting units employed and minimizes the yield of discard slag and loss of metals in slag; in addition, it resolves the problem of sulfur dioxide utilization.

Jan 1, 2003

By V. Madhusudhan Rao

Fly ash is a finely divide non ? combustible material obtained as a by ? product of coal combustion. It is a major by ? product of coal based thermal power stations. Until recent past it was considered as a waste and highly polluting material. However its formation can only be minimized by using suitable technology in the boilers. In recent past it is found that Fly ash has many end uses and it has proven itself to be a potential construction material. But the suitability of fly ash for various applications largely depends on the amount of unburned carbon, which is turn depends on the firing method. Fly ash samples from various power plants existing in India using a fluidized bed method and pulverized bed were analyzed and a comparison of these two firing methods was carried. This paper deals with the compositional requirements for fly ash used for the fabrication of insulating doors using AAC (Aerated Autoclave Concrete) and the methods employed to make fly ash suitable for this purpose. It also includes the latest ?U? beam technology for effective fly ash recycle. If the by products of coal combustion from power plants like fly ash as the paper stresses are utilized properly, it is not an exaggeration to say that power generation is possible with absolutely zero cost.

Jan 1, 2006

By S. H. Castro

In 1997 Chile was the world&apos;s largest copper mine producer with around 3.4 million metric tomes of copper. Conventional technology (conminution-flotation- smelting-converting-electrorefining) for copper sulfide ores was used. For copper oxidized ores hydrometallurgical processes (heap leaching-solvent extraction- electrowinning) were employed. Consequently, the most important waste effluents include flotation tailings, gaseous emissions, smelter slags, acidic and alkaline wastewater, electrolytic sludges, solid residues from leaching, etc. The introduction of stricter environmental regulations are forcing the Chilean industry to minimise the generation of waste and promote cleaner production. Gas emissions such as SO2 and arsenic from smelters and process wastewater are the major problems at this stage. The environmental impact assessment of gas emissions in all six largest smelters namely Chuquicamata, Caletones, Potrenllos, Ventanas, Paipote and Chagres led to design a "decontamination plan." The implementation of this plan resulted in (i) the installation of sulfuric acid plants for SO2 abatement and (ii) the installation of electrostatic precipitators to remove arsenic oxides condensed from cooling gases. The aim of this paper is (i) to describe the type of waste associated to the various stages of the metallurgical processes and (ii) review the main abatement technologies used in medium and large size companies.

Jan 1, 1999

Over the years, numerous hydrometallurgical processes have been proposed as an alternative or complement to smelters for the treatment of copper concentrates. Most of these initiatives met with limited success. Bioleaching is applied commercially for secondary copper minerals heaps and dumps, and bacterial leaching processes are being developed for copper concentrates, although industrial application is still years away. More recently developed processes usually include pressure leaching and/or ultrafine grinding. This paper proposes a new leach process to treat copper sulphide ores or concentrates: the process operates under atmospheric pressure and uses limited concentrations of ferric sulphate as oxidant; the key to the process is the regeneration of the ferric ion, which can be effected in-situ (direct process) or ex-situ (indirect process) using SO2/O2. Examples are presented for the treatment of copper concentrates by agitation leach and of copper ores by heap leaching. Application of the process to copper gold ores and chalcopyrite concentrates is also discussed.

Jan 1, 1999

By M. A. S. Siraa

A program of work was undertaken at the Kennecott Smelter and Refinery to model the complex. This effort contributed a total of eight models of the plant: flash smelting furnace, flash converting furnace, slag concentrator, anode furnace, offgas scrubbing system, acid plant, hydrometallurgical dust treatment plant, and the precious metals plant. Some of these models have been used in a variety of investigations ranging from offgas capacities for a steam generation analysis to an examination of impurities. The culmination of this enterprise has resulted in an on-line control scheme for the flash smelting and flash converting furnaces. These two process control schemes incorporate their respective steady-state heat and mass balances that are executed in response to feed changes while a feedback loop calculates when product grade and temperatures deviate from setpoints. This system has been put into place to improve furnace control and on- line time.

Jan 1, 1999

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. is carrying out a low cost production using a Tamano Type Flash Smelting Furnace (T-FSF), which is an improved version of Outokumpu Type Flash Smelting Furnace but without slag cleaning furnace and also by developing its own coke combustion technology. Coke combustion technology that is the basis of the system has been improved several times and, at present, it has evolved to a stage where it can be reproduced on the Computer guided system for Coke Combustion in the T-FSF (CCCT) using a general- purpose computer. This CCCT is featured by &apos;its trend control and predicting function, and an operator can freely control the operation parameters so as to control the operation flexibly. We have recently developed an overall energy reduction system covering the Smelting Plant to Sulfuric Acid Plant, which we call an Optimum Low Cost Operation System (OLCO) to reconsider the energy costs including coke, heavy fuel oil, and electric power. In this report, we would like to present the recent operation of T-FSF based on CCCT as well as the optimum energy operation utilizing OLCO system.

Jan 1, 2002

By Nathaniel Arbiter

The first ammonia leaching plants, applied to copper carbonate and native copper tailings in 19 15, were followed more recently by research and development of flowsheets for ammonia leaching of sulfide concentrates. These were applied to two commercial plants. Anaconda&apos;s Arbiter Plant started up in 1974 with a design capacity of 36,000 tons/year of cathodes, to be produced by ammonia leaching with oxygen, followed by solvent extraction and electrowinning. The plant shutdown in late 1977 as a result of high maintenance and operating costs, partly due to harsh winters; to complications associated with sulfate disposal; and to changes in mineralogy. BHP&apos;s Coloso plant in Chile was designed to produce 80,000 tons/year of cathodes by leaching part of Escondida&apos;s concentrate production. Using a similar flowsheet but with air and low temperatures to avoid sulfate production, it started up in late 1994 and shutdown in mid-1998, after failing to reach cathode design capacity, and experiencing problems with its technology. The paper reviews the technologies and also alternative methods for overcoming the problems.

Jan 1, 1999

By R. Upadhyaya

Aluminium alloy matrix cast composites have been synthesised by incorporating fine graphite powders (0.5 - 20 µm size) and chopped carbon fibres (6.5 pm P). 3-6 mm length) by liquid metallurgy technique. Incorporation of these second phase materials exceeding 6-8 wt% invariably resulted in agglomeration of the dispersoids and sometimes leading to even total rejection. It was found that small additions of mischmetal (1-3 wt%) during dispersion resulted in better incorporation without much agglomeration of the dispersoid as evident from the macro and micro structures of the composites. Further, the additions of mischmetal increased the volume of the effective incorporation of the dispersoid even to the extent 50- 60%. The mischmetal addition results in a significant increase in the power factor of the stirrer motor indicating an apparent increase in the viscosity of the system. The higher viscosity of the melt increase the shear transmission conditions within the melt during stirring thereby breaking the agglomerates of the dispersoids. The increased viscosity of the melt seems to be due to the formation rare earth - aluminium inter metallics precipitation, as observed in the metallographic studies, thereby making the process a "pseudorheocasting? technique. A provisional patent has been filed based on this work.

Jan 1, 1989

By C. M. Acuna

Scarcity of high grade copper low impurity content ores is a reality and processing of low grade dirty concentrates is a need. In spite of this fact, innovative strategies have to be looked at to comply with day to day more stringent environmental regulations. From this perspective the production of matte grades over 70% in copper presents several merits, but it must be contrasted with the fractional distribution of impurities reporting to the condensed phases. Converting of white metal high in arsenic content results in moderate fraction of arsenic to gas, but high deportment to blister. Therefore, production of anode copper, as required by the electrolytic refinery, may result in several operational difficulties. Furthermore, by recycling the flue dust and slag produced in the smelting-fire refining cycle, the arsenic content in the feed to smelting increases and so does in the resulting anode copper. The Teniente Converter, as a smelting unity, has probed suitable for production of high matte grade near white metal composition but regarding distribution behaviour of impurities there is lack of reliable data, specially when processing concentrates over 1% in arsenic content. In the new scenario, i.e. low grade copper high arsenic content concentrates, to fully asses the merits of this technology the effect of matte grade, secondary materials recycling and arsenic in feed upon the distribution coefficient of arsenic between slag and matte, mainly, must be evaluated both from a theoretical approach and by use of industrial data. Based on available data correlations of distribution coefficient, matte grade and matte/slag ratios with arsenic in feed and copper content in slag are worked out. Based on these results suggestions as to matte grades facilitating to deal more efficiently with the handling of smelting byproducts are proposed.

Jan 1, 2006

By Susan A. Fredholm, Randolph E. Kirchain, Elsa A. Olivetti, Jeremy R. Gregory, Jeffrey B. Dahmus

"A general model for evaluating the economic and environmental performance of electronics recycling systems is developed. This model comprehends the three main functions in a recycling system – collection, processing, and system management – and aims to enable quantification of the impact of context and system architecture on the economic and environmental performance of electronics recycling systems. Such a model can be used both to evaluate and improve existing electronics recycling systems, as well as to design and implement new systems. A case study, based loosely on Maine, is presented to show the utility of such a model.IntroductionAs recycling systems for complex durable goods (CDGs), and in particular for waste electronics, become more widespread, understanding the economic and environmental performance of such systems becomes critical, both to enable improvement of existing systems and to inform the design of new systems. However, with the range of possible system architectures and the important role of locational characteristics (context), understanding the determinants of system performance is challenging [1]. To address this issue, a modeling framework to project the economic and environmental performance of CDG recycling systems, based on contextual and architectural characteristics, has been developed.The modeling framework presented here comprehends the three main functions – collection, processing, and system management – which are common to most recycling systems. These three functions are modeled using a variety of modeling techniques and serve as a bridge between inputs related to system context and system architecture, and outputs related to economic and environmental performance. The models developed here are intentionally meant to be both broad, in order to address entire recycling systems, and general, such that many different systems, both real and hypothetical, can be analyzed."

Jan 1, 2008

By Ruben Alvarado

The need to increase business competitiveness while complying with environmental requirements represent the great challenge that the Caletones smelter has decided to face in a new development project with a compromising and willing alliance with its workers. To date, the project is at the feasibility stage, with start up scheduled for the middle of the year 2002. The processing capacity of the Teniente Converters will be increased to levels up to 2400 tpd of chalcopyrite-based concentrates containing 30% Cu, by means of more intensive use of oxygen and improved stabilization of the overall operation. Productivity increses in the converting of white metal and the pyrometallurgical treatment of slag are also planned. As a result of related strategies, the productivity of the supporting facilities, included the capacitiy of the sulfuric acid plants, will be increased. An intensive and well-designed labor-upgrading scheme will allow the transformation of every worker into an expert in his working areas, thus becoming an active driving force in technology development. Mechanization, appropiate infrastructure, and complete process control and instrumentation will give to the skilled and motivated personnel the necessary tools in order to attain the highest potential ever reached with the Teniente technology. The necessary investment for this project based on the adding facilities to the existing plant is only a third of that required to reach the same objective for a greenfield plant, thus yielding a very high return on investment.

Jan 1, 1999

By Shaohua Ju, Jin-hui Peng, Ya-jian Wang, Shuai-dan Lu, Li-bo Zhang, Lei Guo

"The granulation of a red mud is of great importance for recycling this material as an adsorbent for waste water or gas. A new granulating process was developed and its effect was evaluated. To reduce the cost of the granulation process, the wet filter cake (containing 25% water) was directly mixed with different cement contents (4%, 6%, 8% and 10% based on wet material). The mixtures were placed in a moist environment for 4 days, and then were washed with deionized water until the pH values of leachants were lower than 9.0. The efflorescence ratio, surface area and particle size of the aged mixture were determined, respectively, by bottle shaking experiments, N2 adsorption and screening. The results showed that the best addition of cement is 2%, and this yielded granulated material with a particle size of less than 2 mm, an efflorescence ratio of 4.83% and a specific surface area of 17.42 m2/g.IntroductionRed mud is a residue of the aluminium industry that is produced during the alkaline extraction of alumina from bauxite by the Bayer process. For every ton of alumina that is produced, the amount of red mud generated can vary from 0.3 to 2.5 tons, depending on the characteristics of the bauxite. In its typical form, red mud is brick red in colour, caustic, about three times as dense as water and, when un-neutralised, has a high pH, typically around pH 13 [1]. It is primarily composed of iron oxide, silica and alumina, along with traces of heavy metals. Red mud particles are quite small; typically 99% will pass through a 0.6 mm sieve and 87% through a 0.038 mm sieve [2],"

Jan 1, 2012

By Nan Zhang, Gai-feng Xue, Shangchao Liu, Benquan Fu

"The high-magnetization microspheres of Fe3O4 encapsulated with S1O2 and T1O2 layers (Fe3O4@SiO2@TiO2) were prepared. The microspheres were characterized by transmission electron microscopy and scanning electron microscopy. These high-magnetization microspheres could be readily dispersed by shaking whereas they could be rapidly separated from the aqueous solution simply by applying an external magnetic field. The two shells of S1O2 and T1O2 protected the iron oxide well and the microspheres were stable in acid and base solutions. Therefore, they have a good potential for the enrichment of phosphopeptides or photocatalytic activity. They could also be used to remove metal ions from waste water.IntroductionSolid-phase extraction (SPE) is the most commonly used separation technique for its simplicity, consumption of small volumes of organic solvent, and the ability to achieve a higher enrichment factor. The quest for new adsorbents is an important factor in improving analytical sensitivity and precision in SPE techniques. To date, many novel adsorbents, such as nanometer-sized materials, carbon nanotubes, mesoporous materials and magnetic nanoparticles have been employed in SPE.Magnetic polymeric microspheres, an interesting advanced composite material, have received increasing attention in the past few decades because of their unique physical and chemical properties and their potential for use in applications in various fields [1]. Magnetic microspheres consisting of an iron oxide core and a silica shell have attracted particular attention for their unique magnetic response, low cytotoxicity, and chemically modifiable surface. The core-shell magnetic silica microspheres have shown great potential in the fields of biotechnology and biomedicine for applications such as cell labeling and separation, enzyme and protein separations, targeted drug delivery, and magnetic ferrofluids hyperthermia."

Jan 1, 2012

By Xuyang Liu, Xuewei Lv, Chenguang Bai, Meilong Hu

"The electro-deoxidation process for ilmenite concentrate in molten salt was studied by cyclic voltammetry and AC impedance spectroscopy. The results from cyclic voltammetry are consistent with those of AC impedance spectroscopy. The results showed that the electro-deoxidation process for ilmenite concentrate consists of two steps. In the first step, Fe is reduced from the ilmenite concentrate. The second reaction is the decomposition of TiCh. CaTiCh is an intermediate product. At low voltage, the electrochemical reaction is the main step. With the increasing potential, the diffusion of ion is the main rate controlling step for the electro-deoxidation of FeTiO3.IntroductionTitania and titanium-rich products are mainly prepared from ilmenite concentrates (FeTi03), which contain about 40%-60% T1O2 after ore dressing and other physical or chemical processes [1]. At present, the main methods to prepare titania are the sulfuric acid process and the chloride process, but the sulfuric acid process consumes a large amount of sulfuric acid and the materials requirements for the chloride process are strict [2], Since the Electro-Deoxidization in Molten Salt (FFC) method was put forward in 2000, many researchers have successfully extracted the metal and alloys by this method, such as Ti, Cr, Tb, Si, Al-Si, TiV, FeTi, etc. [3-7], FeTi alloy is a typical hydrogen storage material, and because of its favorable properties, the preparation of FeTi alloy has become a hot research topic [7-9]. However, the mechanism of electro-deoxidization has not been studied thoroughly [10-11]. Therefore, in this study, the electro-deoxidation process for titanium concentrate was investigated by electrochemical methods, and the study makes a contribution to improving the current efficiency of the electrolysis."

Jan 1, 2012

By M. Brian Maple

A rich variety of phenomena are produced by superconducting-magnetic interactions in rare earth and actinide compounds. These phenomena, and the materials in. which they have been observed, are described in this talk, with an emphasis on the new high superconducting transition temperature (Tc) copper oxides. The Materials The-materials in which these phenomena occur can&apos; be divided into two classes. In the first group, there are two distinct interpenetrating systems of electrons, a set of localized 4f or 5f electrons and a set of itinerant electrons. The localized f electrons carry magnetic moments and interact with the spins and momenta of the the itinerant electrons, which are involved in the superconductivity, via exchange and electromagnetic interactions; respectively. This category includes materials containing rare earth (R) and actinide elements with partially-filled f electron shells which have been inroduced as substitutional impurities [e.g., La1-xCexA12, Th1-xUx] or form a sublattice in compounds [e.g., RRh4B4, RMo6S8, RMo6Se8, the high Tc. superconductors RBa2Cu3O7-d(d - 0.05)]. Materials of the second type are characterized by a single band of electrons that is responsible for both superconductivity and magnetic order. This group includes heavy electron rare earth and actinide compounds [e.g., CeCu2Si2, UBe13, UPt3, URu2Si2], and the high Tc copper oxide superconductors such as the hole-doped systems Lag- MxCuO4 (M = Ca, Sr, Ba, Na) and RBa2Cu3O7-d(0 =d= 1) and the electron-dope system Ln2-xMxCuO4-y (Ln = Pr, Nd, Sm, Eu; M = Ce, Th; x = 0.15; y - 0.02).

Jan 1, 1992

By Ibrahim Yusufoglu, Cem Kahruman, Sedat Ilhan, Ahmet Orkun Kalpakhi

"Scheelite is the main raw material in tungsten production. In hydrometallurgical processes, extraction of tungstate ions into solution is very important. During the leaching of scheelite in oxalic acid solutions, tungsten dissolves as a chelate complex. Scheelite includes impurities along with calcium tungstate. Determination of the dissolution of these impurities is important in the subsequent tungsten production stages. In this study, scheelite was dissolved in oxalic acid solutions and the dissolution of impurities was investigated. The quantities of dissolved impurities were determined by ICP - OES and characterization of the undissolved impurities in the leach residues was carried out by SEM - EDS analysisIntroductionScheelite and wolframite ores are used for the industrial production of tungsten. Both ores are dissolved in acidic or basic solutions, and ammonium paratungstate is obtained as an intermediate product. Prior to crystallisation of ammonium paratungstate, all the impurities must be removed. Among these, Fe, Si, P, Mn, Mg and Mo are classified as ""harmful"" elements and different methods are used for their removal [1]. During purification, solvent extraction, ion exchange, etc. methods are used.Potashnikov et al. [2] studied the dissolution of scheelite in acidic solutions and the effects of stirring speed, temperature and oxalic acid concentration on the dissolution kinetics.There are no works in the literature about the removal of impurities from scheelite ores in oxalic acid solutions. Therefore, the aim of this work was to investigate the dissolution mechanisms of impurities during the leaching of scheelite in oxalic acid solutions. The effects of temperature and oxalic acid concentration on the dissolution were also investigated. In addition, the characterization of the impurities which were not dissolved was studied."

Jan 1, 2012