Search Documents

By Z. Zhang, Cuihuan Huang, Zongshu Zou, Nan Wang, Xueqian Xin

"Vitrification is considered as an attractive procedure for municipal solid waste incineration ash, which can realize the volume reduction and innocent treatment of incineration ash, as well as reuse of bottom ash. The main oxide components of molten ash slag are CaO, Al2O3, SiO2, Fe2O3, MgO, and Na2O, accounting for more than 90% of the total mass. The phase relations and thermodynamic properties of the CaO-Al2O3-SiO2-FeOx-MgO-Na2O oxide system is highly required, and is of great scientific significance for optimization of vitrification processing and sustainable resource utilization of melting slag. A study on the equilibria phase relations of CaO-SiO2-MgO-FeOx system was done by using CALPHAD method based on FactSage in this paper. The modeling parameters for the thermodynamic properties of liquid phase in CaO-SiO2-MgO-FeOx system were established and the equilibrium phase relations of MgO-SiO2-FeOx and CaO-SiO2-FeOx-MgO systems were calculated for different temperatures and oxygen partial pressures.IntroductionThe main oxide components of vitrified bottom ash slag are CaO, Al2O3, SiO2, Fe2O3, MgO, and Na2O, accounting for more than 90% of the bottom ash by weight [1]. During slag processing and modification, the knowledge of thermodynamic properties and liquidus temperature in the related slag system is highly required [2-5], which is not yet available. Through literature survey [6-9], it is clear that the systematic information on the concerned complex slag system is scarce. Most binary subsystems except FeOx-Na2O have been investigated well. Among ternary subsystems, few phase relations of the Na2O-MgO-SiO2 ternary system are available. For the phase relations of the system Na2O-MgO-Al2O3, all the studies are focused on the Al2O3-rich region. Investigation on the CaO-Al2O3-FeOx system is limited to Fe2O3-containing system with relatively higher oxygen potential. Most quaternary systems are not studied well except the CaO-MgO-Al2O3-SiO2 system, mainly due to their metallurgical importance. Figure 1 demonstrates the research status of the vitrified bottom ash slag with almost zero effort [10]. The effort here is defined based on the published literature by considering the number of publications, the investigated composition ranges, and the research details. So far the engineers in the field have to make assumptions of the thermodynamic properties of the simplified oxide system, without taking into consideration the interactions of the different oxide components, which hinders the development of the slag valorization and utilization. In order to provide thermodynamic properties for the application of the vitrified bottom ash, the six-component oxide system (CaO-MgO-Al2O3-SiO2-FeOx-Na2O) will be investigated through both experimental approach and computer modeling."

Jan 1, 2011

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By T. Malvik

Norway is a big producer of ferrosilicon and silicon metal. The raw material is quartz and quartzite and large quantities from both Norwegian and foreign sources are used. The demands maade on both the chemical purity and the thermomechanical qualities of the quartz/quartzite have increased in recent years in an attempt to reduce energy consumption and to improve utilization. Control of the chemical quality of the raw material is relatively easy by means of routine analysis, but it is more difficult to find a suitable method for testing the thermomechanical properties. A rapid test method to define high quality quartzite deposits for use in the metallurgical industry has been developed. The method is based on a combination of chemical analysis, dilatometry, thermosonimetry and cathodoluminiscence.

Jan 1, 1989

By Jacob Bummer, Greg Roset, Dayle Flynn

"IntroductionStillwater Mining Company operates a Precious Metals Smelter (PMS) located in Columbus, Montana USA. The PMS processes iron, copper, and nickel sulfide bearing concentrates containing platinum, palladium, gold, and rhodium. The concentrates are produced from two mines in the Beartooth Mountains located in south central Montana. The PMS utilizes a 7.5 megawatt 3-in line electric furnace to smelt the concentrates, and two Top Blown Rotary Converters (TBRC's) to remove iron. In addition to the mine concentrates, the PMS also processes various forms of Platinum Group Metal (PGM) bearing recycled catalyst. The sulfide matte produced within the electric furnace and TBRC's acts as a collector for the PGMs. Throughout the operation of the PMS, there are three different forms of molten material that are processed through the Stillwater Granulation system: TBRC matte, TBRC slag, and electric furnace matte. This paper describes the operation of this granulation system.Tapping the FurnaceWhen a sufficient level of molten PGM bearing matte has been reached within the inner volume of the electric furnace, the molten material is ""Tapped"". Tapping requires drilling into the electric furnace until reaching the molten matte phase. The matte phase will drain out of the drilled hole through a graphite launder into a 5 ton refractory lined ladle. Once the ladle is full, the tap is plugged with a mud gun."

Jan 1, 2012

By Sung Tae Kim

The viscosity is one of the most critical properties of slags and thus its influence on the physicochemical phenomena in metallurgical processes has been issued for last decades. The viscosity of ferrous- and non-ferrous metallurgical slags can be understood via structural investigation with spectroscopic methodologies including x-ray photoelectron spectroscopy, infrared- and Raman spectroscopy, and solid state nuclear magnetic resonance spectroscopy, etc. Therefore, the reaction kinetics such as desulfurization in ladle metallurgical furnace, reduction of FeO and MnO in electric arc furnace is strongly dependent on the viscosity of the slags. The rates of oxide (inclusion and refractory) dissolution into the slags and fluxes are governed by the viscosity. Alternatively, the structure of aluminosilicate melts also affects the thermochemical properties such as sulfide capacity, etc. These diverse applications of the viscosity-structure relationship to ferrous- and non-ferrous metallurgical processes were reviewed.

By S. N. Lekakh

Experimental work and thermodynamic simulations of cast iron refining were carried out using various additions of alkali and rare earth metals. The refining reactions for sulfur and oxygen removal were studied for melts treated with Mg, Ca, and Ce. The measured data and the results of the computer simulations were in agreement. Experimental kinetic data, together with the thermodynamic calculations, were used for optimization of the amount and sequence of the addition of nodulizers for ductile iron production.

Jan 1, 2009

By J. L. Sanchez

Using a special double-zone transpiration reactor, the vapor transport chemistry of vanadium pentoxide in the presence of water vapor has been investigated. Three possible volatile hydroxides above V,O,(s) are reported in the literature: VO,(OH),, V,O,(OH),, and VO(OH),. In the present study, it was established that VO(OH), is the principal gaseous hydroxide species formed. The predominant reaction was found to be: { } The vapor pressure of VO(OH), was measured as a function of temperature, water pressure, oxygen pressure and flowrate. The results have been used to determine the Gibbs free energy of the above reaction as a function of temperature: { } The results of the present work were combined with thermodynamic data reported in the literature to obtain expressions for the AGO for the reaction above V,0,(1) and the AGO of formation (units in cal/g-mole).

Jan 1, 1993

By Mieke Campforts

The usefulness of the water-cooled probe technique to experimentally study slag solidification and freeze lining formation in pyrometallurgical reactors is evaluated. With this technique a layer of solidified slag is formed on a water-cooled probe that is submerged into a liquid slag bath. The influence of the submergence time and the heat input is examined. The solidified layers are analyzed with light microscopy, electron microscopy, electron probe micro-analysis and X-ray diffraction. Thermodynamic software is used to interpret the solidification microstructure. The results demonstrate that the technique is useful to understand freeze lining formation.

Jan 1, 2006

By S. W. White

Plasma arc technology is increasingly being used to process a number of waste materials. In present research, plasma technology is being investigated to treat waste magnesium baghouse dust, which is a waste material from the Magnetherm process. This dust contains mostly MgO, but also contains NazO, CaO, and KzO. Plasma energy is to be used along with a reducing agent to produce pure gaseous magnesium while keeping the other materials in a slag. The magnesium will then be collected by rapid quenching. A non-transferred arc plasma torch is ideal for this reaction because of its high enthalpy and improved energy efficiency over conventional methods. Another advantage of plasma is that it allows for the pre-heating or pre-reacting of fine particles before contact with the melt. Thermodynamic calculations using the Gibb energy minimization method were used to determine the most stable compositions of the materials at various temperatures. Energy balances have also been calculated. These results conclude that we can recover approximately 98% of the magnesium with a proper quenching technique. The calculated results are compared with the experimental data, and good agreement between them was observed.

Jan 1, 1999

By Geir Wedde, Anders Sorhuus

"Vast quantities of energy are released as heat to the environment from industrial operations. Many countries target waste heat recovery to mitigate CO2 emission. Exhaust gases from industries such as primary aluminium smelting, carry a substantial portion of the waste heat generated. For a cost efficient capture of more valuable heat (higher exergy), heat exchangers should operate on the exhaust gases upstream of the gas treatment plants. Heat exchange surface would be exposed to dust laden gases with risk of fouling. Heat exchangers of innovated design and operation have overcome the potential of excessive fouling rates. Heat exchangers of the ""shell and tube"" design have been demonstrated for exhaust gases from ferroalloy as well as primary aluminium smelters. In addition to the heat recovery, gas cooling results in smaller gas treatment plants with lower costs and reduced emission. The aluminium experience is exampled in the paper.IntroductionIndustrial usage of energy continues to grow as a result of increasing volumes of production, a trend that is likely to continue in the coming decades as living standards keep rising globally. World energy consumption (Figure la) is to grow 49 % by 2035 (ref. 2010) as reported by EIA [1]. The industrial sector consumes somewhat more than 50% of the total world energy consumption predominantly the energy increased demand comes from non-OECD countries in Asia. The industrial consumption by production of metals iron and steel accounts for 14 % and for non-ferrous metals 3 % mostly for aluminium production (Figure lb). Aluminium production will be discussed in this paper as an example of an industry with large quantities of waste heat to recover"

Jan 1, 2012

By Merete Tangstad, Eli Ringdalen

"In Norway ferrosilicon/silicon and ferromanganese production are strong with world markets of 4 % / 9 % and 4 %, respectively. Research and development in the academia mirrors the national interest; hence, there has been extensive academic research in these areas. There are some vital drivers and premises for a successful cooperation between the academia and industry with the main driver being a win-win situation for both. For industry,the potential advantages include cost-, competence- or environmental- benefits; for academia, the important drivers are building of competence and equipment, educating more students at higher levels, and increased possibilities to publish. In Norway, the benefits of cooperation between industry and academia are basic knowledge regarding thermodynamic and kinetic data, as well as reaction mechanisms within core processes. In recent years, such research interests have focused on the depletion of raw materials as well as environmental issues.IntroductionIn 1989, the Norwegian Ferroalloy Producers Research Association (FFF) was funded on the belief that a common research association would benefit the industry by making it easier to perform basic research as well as paving the ground for better recruitment to the industry. The funding partners in Norway were the FeSi/Si and FeMn producers. Today, the producers are Elkem, Finnfjord, Fesil, Wacker, Eramet and Vale. The main research partners working with FFF are SINTEF (Materials and Chemistry) and the Department of Material Science and Engineering at the Norwegian University of Science and Technology (NTNU). With more than 1700 employees, SINTEF is the largest independent research organization in Norway and NTNU is the largest technical university. Together, the two organizations provide an exceptionally strong materials technology research environment, and especially so for pyrometallurgical research."

Jan 1, 2012

By Rauf Hurman Eric

In this review paper the effect of composition and temperature on electrical conductivity and viscosity of the slags encountered in electric smelting of PGM-containing sulfide concentrates is described along with their liquidus temperatures. Optimization of slag composition is attempted on the basis of opposite trends of viscosity and electrical conductivity. Metal losses to slag, matte-slag separation and matte settling are also discussed in conjunction with interfacial and surface tension concepts. The electrode immersed in the slag phase is the main factor in the design and operation of the furnace. The most important electrode parameters are the size and the positioning in the slag phase which are determined by the slag resistivity, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles within the slag phase which in turn affects the flow conditions. Thus the flow of slag is discussed together with furnace geometry, stirring action, buoyancy and electromagnetic effects and the action of the electric furnace as a settler is emphasized. A discussion on the design d production capacity of the furnace is provided which are based on considerations derived mainly from slag properties.

Jan 1, 2006

By P. T. Velu

Solubility of metal oxides in the molten salt electrblytes is an important parameter in the electrochemical processing of metals and alloys. The efficiency of an electrochemical process primarily depends on the quantity of metal oxide present in the electrolyte in the dissolved form and its thermodynamic properties. The activity of CeO2 was calculated using the free energy of fusion of CeO2,{ AG°m, CeO2. The AGOm,CeO2 }was deduced from the values of enthalpy, heat of fusion and melting point of Ce02. The activity coefficients of CeO2 as a function of temperature and melt composition were calculated. The thermodynamic data such as integral molar enthalpy, entropy and Gibbs energy of formation were calculated as a function of composition and temperature.

Jan 1, 1994

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering material. Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to design new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass spectrometer.

Jan 1, 2003

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By Zongshu Zou, Qiang Li, Mingming Li, Mingxia Feng

The impingement onto the surface of bath by top-blown jets is a significant process characteristic in BOF and EAF steelmaking process. The cavity is one of the most important outcomes of the interaction and plays an important role on reaction kinetics and reactors performance. But to date, the understanding to cavity is still so limited. In present study, a water model for a BOF converter is established and the dimension of cavity profile is investigated. The effects of lance height, gas flow rate, nozzle inclination angle and the amounts of slag are discussed. The results show that penetration depth increases with the increase of gas flow rate and the amount of slag, and the decrease of lance height and nozzle inclination angle. Furthermore, a theoretical model of cavity dimension is proposed for multiply jets impinging liquid bath on the basis of energy balance at the stagnation point of cavity.

Jan 1, 2015

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"For optimum smelting results, proper treatment of the feed is needed to ensure favourable conditions for ignition characteristics, heat balance, mass balance with tolerable impurity levels, and overall process economics. Feed preparation consists of physical treatments before drying (blending), chemical treatments before drying, (roasting, if required), drying itself and physical treatments after drying (fractioning, if required).Effects of fluctuation on mineralogy and moisture should be minimized by blending the concentrates in a bedding plant prior to drying. As an alternative to drying, additional treatments such as roasting for impurity removal may be needed for part of the concentrate.Sustainability, energy efficiency, utilization of waste energy, low gas and dust emissions, product quality, availability and occupational exposure reduction are decisive criteria in drying today. These criteria are best met by the Kumera steam dryer, which has the best energy efficiency, zero CO2 emission, lowest operational and maintenance expenses, and superior availability and product quality.IntroductionFeed preparation plays a crucial role in having a smooth smelting operation and also the overall smelting economics in metal production. Therefore, it is of significant importance for all copper, nickel and lead smelter operations in which sulphide concentrates are fed to the primary smelting furnace. Generally speaking, the higher the metal content in the matte after primary smelting, the more important the feed preparation. This is of particular importance in the direct blister (DB) process for copper production and direct oxygen nickel (DON) for nickel production.Bedding is the first stage in feed preparation. This is very important for the sake of smoothing the mineralogical fluctuation in the feed for better smelting control. Its importance increases as the number of concentrates available for the feed mix decreases."

Jan 1, 2012

By Basak Anameric

Pig iron nugget process was developed by Kobe Steel as an environmentally friendlier, economical alternative to traditional blast furnace process. The process aimed to produce highly metallized, slag free pig iron nuggets throughout a single stage heat treatment, utilizing coal as a reducing ? carburizing agent. The objective of this work was to determine whether the pig iron nuggets produced at the laboratory conditions had comparable physical and chemical properties with the blast furnace pig iron. The physical and chemical properties of the pig iron nuggets were determined utilizing x-ray fluorescence spectroscopy, x-ray diffraction, optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and apparent density measurements. The pig iron nuggets had similar chemical composition and apparent density values (6.7 ? 7 g/cm3) with blast furnace pig iron and they had microstructures similar to low carbon white cast iron. These properties make them a competitive alternative to blast furnace pig iron.

Jan 1, 2006

By Caisa Samuelsson, Fredrik Engström, Bo Björkman, Margareta Lidström Larsson

"Large amounts of by-products are generated by the Swedish steel industry each year. The EAF-process generates about 400 000 ton of slag, from which 80% is deposit. An alternative to deposit is to use slag as road construction material. However, metal content in the slag can be a problem, due to the leaching. The aim of this work was to investigate how stable these materials are when ageing and kept outside. Five different EAF-slags from domestic steel plants were used in this study. The materials were characterised after 0, 6, 12, 18 and 24 month to evaluate the ageing process. Scanning electron microscope (SEM), x-ray diffraction pattern (XRD) and a standard test for leaching were used. The changes in behaviour differ between the five materials. The total leachability decreases with time for all samples. CaCO3 is formed on slag surfaces as CaO reacts with moister and CO2 in the air. Introduction The slag generation in the Swedish steel industry is about 1.5 million tonnes annually, of which more than 500 000 ton is generated in EAF (Electric Arc Furnace), AOD- (Argon Oxygen Decarburization) converters and during the refining of steel in the ladle metallurgy. Some of the slags are used in different applications, but most of the steelmaking slags produced in Sweden are landfilled today. The chemistry, mineralogy and physical characteristics of slags make it a suitable material in construction, replacing for example, gravel and rock [1]. In some respects, in road construction, it may even be technically superior to virgin material. Slag from scrapbased steelmaking is used for road construction in Europe. The reason for the low utilization in Sweden is mainly due to potential leaching of harmful elements, legislations and competition with easily available natural raw materials. Except the potential leaching, the technical obstacles for not using some slags in construction include:"

Jan 1, 2008