Search Documents

By Heiner J. Sander

Stanford University operates the National Research Facility which is located at the Stanford Linear Accelerator Center (SLAC) in Menlo Park, California. In order to improve and allow for enhanced experiments, the current facilities required expansion. A1500 foot long tunnel (20 ft wide by 21 ft high) and a 220 foot long underground cavern (49 ft wide by 32 ft high) were excavated through the Ladera Sandstone formation which is an intermediate geo-material with week rock properties. The overburden between surface and crown of the structures varies from 10 to 80 feet. The underground structures were excavated according to the principles of the NATM (New Austrian Tunnel Method). This paper addresses the challenges that were encountered during the construction phase of the project and how construction issues were resolved mutually by the owner, engineer and contractor. The implementation of geotechnical instrumentation, recorded data and interpretations, soil conditions and behavior encountered during construction are also presented.

Jan 1, 2008

By Donald W. Stever

In 1995 I was asked to participate in a litigation matter between a corporation and its insurance carriers concerning insurance coverage for remedial costs at a large, environmentally contaminated closed-down former industrial facility. One of the buildings on this site became known to the lawyers representing the company as “the infamous Building 8”. This building housed millions of documents retrieved from various locations at the facility while it was being shut down. It became apparent that the facility management had no document destruction policy, and thus Building 8 contained internal memoranda, notes, copies of correspondence, permits, operating records, inventory records, and the like from fifty years of operation. Needless to say, some of these documents, all of which were subject to discovery by the insurance companies in the litigation, contained material that was less than helpful to the company’s case. Of course, there were also a few helpful documents, but the overall usefulness of these records was outweighed by the negative impact they had on the conduct of the litigation. A second example involves e-mail. Several years ago, acting on an anonymous complaint that we later discovered was made by a disgruntled former employee who had been fired, a small army of federal environmental investigators descended on a client’s operating facility and, armed with a search warrant, literally commandeered the facility’s EH&S department. The investigators impounded the computers of the EH&S personnel and extracted all of the data from the hard drives of those PCs, as well as all EH&S related files from the hard drives of several servers used by the facility. These computers contained many years’ worth of stored e-mails, draft letters and memoranda, and other documents that provided grist for a four and one-half year criminal grand jury investigation of the facility and its EH&S staff. Both of these companies would have benefited from following a rigorous, enforceable, corporate records policy. Here is a third problem. My client had, during the 1960s, made a brief, and unprofitable foray into the nuclear fuel processing business. It ultimately sold the subsidiary, and was forced to give the purchasing company a broad indemnity against future liability. As might be expected, years later the facility was found to have considerable soil and ground water contamination both by chlorinated solvents and low-level radioactive material. Several years into the remediation program, my client discovered a tractor-trailer load of files, apparently removed from the subject facility, sitting in a parked trailer in a company-owned lot 300 miles away from the facility, where they had been for nearly thirty years. These documents were not helpful to the client, but had to be reviewed, at considerable cost, by paralegals. Moreover, several of the boxes turned out to have been mildly radioactive, setting off a chain of health and safety issues that consumed tens of thousands of dollars of legal expenses before they were resolved. Today, formal, enforceable corporate records management programs have become an extremely important element of overall corporate management. What was for most of the last century little more than a low level warehousing function is now a critical, actively managed, operating function that affects every level of corporate management. The rapid assimilation into corporate culture of electronic document management and the prevalence of e-email as the primary means of internal communication have created records management complexities the likes of which were not even conceived of fifteen years ago. Record preservation and destruction are no longer matters that can be handled on an ad-hoc decision making basis. Because of regulatory requirements affecting various classes of documents and the litigation consequences of ad hoc retention and destruction of corporate business records, and the need to have the ability to quickly retrieve documents in either a litigation or business negotiation context, a set of records management norms have evolved over time that have become the core elements of virtually every corporate records program. However, notwithstanding the existence of a set of norms (which are the basic elements of a

Jan 1, 2005

By D. Brün, T. W. Nattkemper, T. Kuhn, T. Schoening

Underwater exploration for marine resources using camera-equipped devices (OFOS, ROV, AUV) is receiving growing attention. This development is creating a continuously growing pile of digital underwater images leading to a serious bottleneck in the analysis. However, any harvesting strategy must be coupled to an efficient and effective assessment of the biodiversity in the area of interest and in nearby control areas. To integrate manual image and computational image interpretation on different levels (i.e. regarding geology and environmental sciences and taxonomy), sophisticated software support is required, which is not yet offered explicitly, neither by commercial software companies nor by academic or other publicly founded institutions. Here, we present the first version of a new digital asset management system that offers functionalities for easy data management, sharing, manual annotation and integration of computational modules for image enhancement/pre-processing and interpretation. The functionality is demonstrated with data from the CCZ provided by the BGR Hannover.

Sep 1, 2014

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid-bake leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400 ºC) sulfuric acid baking of an enargite concentrate followed by water-leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase for baking at 400 ºC. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400 ºC, sulfuric acid amount of 0.5 mL/g of concentrate, and 2 h baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). XRD analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in similar fashion.

Jan 1, 2012

By J. Evans

Including: Tailings thickeners, CCD?s, paste thickeners, HI-rate thickeners, lamella thickeners, high compression thickeners, clarifiers etc. Flocculant dosing control for mining thickeners and clarifiers is influenced by a number of process factors. 1. Flow rate into the thickener or clarifier a) As the flow rate increases into the thickener or clarifier ?retention time? decreases which causes a greater affect hydraulically on the settling solids. So as the flow rate increases it will generally mean an increase in flocculant dosing rate. b) As the flow rate decreases into the thickener or clarifier the retention time increases which reduces the hydraulic affect on settling, improving settling rates. This will generally mean that as the flow rate decreases, we will decrease the flocculant dose rate.

Jan 1, 2011

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

By S. A. G. Poppen, M. B. Mirza, A. I. Cooley

The U.S. Department of Energy (DOE) is responsible for siting and constructing a licensed geologic repository for commercially generated high-level nuclear waste. Within DOE, the Office of Civilian Radioactive Waste Management (OCRWM) Program has this responsibility. To accomplish this mission, the OCRWM Program is engaged in a multidisciplined effort to identify, qualify, and develop repository sites. The current strategy of the OCRWM Program is to identify candidate repository sites in basalt, tuff, and salt and to develop exploratory shafts at those sites. Within OCRWM, the Salt Repository Project Office (SRPO) identified the salt site for the development of exploratory shafts. The proposed Exploratory Shaft Facility (ESF) in salt will have several primary purposes. The shafts will provide access to the reference repository horizon to permit in situ testing of the salt horizons in order to satisfy the following data acquisition needs: • Verification of the salt repository design parameters and validation of performance assessment models • Demonstration of the constructibility • Capability to adequately seal penetrations into the salt An exploratory shaft is required by 10 CFR Part 60 for the conduct of in situ testing at depth prior to submittal of a license application for construction authorization of a repository. Therefore, construction of an ESF will also facilitate the licensing process.

Jan 1, 1987

By G. S. Austin

The St. Cloud Mining Company extracts clinoptilolite about 6.5 km south of Winston, Sierra County, New Mexico. Production is about 18,000 mt/year. Natural zeolites are good adsorbents for positively charged solutes such as ammonium. St. Cloud’s production is used in animal hygiene, animal feed, environmental mitigation, air and water filtration, and other applications. By a simple chemical treatment with a surfactant, zeolites can also be modified to adsorb negatively charged solutes such as nitrate and arsentate, and neutral organics such as solvents and fuel components. These surfactant-modified zeolites are used in treating groundwater contamination, stormwater runoff, and solvent vapors from painting operations.

Jan 1, 2002

By M. M. Poulton

Universities are not immune from the large number of retirements facing the mining industry. Department heads anticipate that we will need to replace all of the senior mining engineering faculty in the U.S. by 2020. Long term studies of Ph.D. completion times and success rates indicate that in Engineering disciplines in the U.S., the ten year completion rate is 65% at best and the four year completion rate is less than 8%. We do not have accurate data on completion rates and times for mining or metallurgical engineering Ph.D. students in the U.S. but students self-report their expected completion times are around 4 years. National data on doctoral students indicate that younger, full time students with sufficient financial support have a higher probability of success in completing their degrees in a timely manner. Students in Eastern U.S. mining engineering programs are on average 32 years old, 85% are full time, and the gap between support and cost of attendance is $5,000 per year. Students in Western U.S. programs are on average 38 years old, 78% are full time, and the financial gap is $8,483. Further, it appears that domestic graduate students are not very geographically mobile. The current demand for new faculty is higher in Western programs but the longer term retirements are higher in Eastern programs. While all Ph.D. students who responded to the 2010 survey indicated an interest in a faculty position at some point in their careers, very few were applying for the open positions. Over the past 35 years for which data could be obtained, the maximum number of Ph.D. students enrolled in mining engineering in the U.S. is 115 with a maximum of 27 degrees granted in one year. On average 89 students are enrolled in doctoral programs in mining engineering in the U.S. with average degree production of 15 Ph.D.s per year.

Jan 1, 2012

By Greg Partington, Darryl Thorburn, Charlene Wildman, Elisa Puccioni, Connie Payne, Campbell McKenzie

"Mineral prospectivity modelling of polymetallic nodule deposits has been completed over the Cook Islands Exclusive Economic Zone (CIEEZ) using the GIS based Weights of Evidence modelling technique. Polymetallic nodules, also known as manganese nodules, have been explored as a possible resource for a number of metals including cobalt since the early 1970s. Recent data on the nodule composition and abundance in the CIEEZ has led to a renewed interest in the prospectivity for manganese nodules in the region. The predictive modelling has used the most recently accepted mineral model for polymetallic deep-sea nodule deposition to identify factors that are most likely to map the presence of this type of mineralisation in the CIEEZ.Manganese nodules form on the deep seafloor as concretions formed by concentric layering of iron and manganese hydroxides around a core and they grow at a very slow rate, on the order of millimeters per million years. The available data for the CIEEZ indicates a greater abundance in the area of nodules formed by hydrogenetic processes, which are the result of slow precipitation of metallic components from seawater. The environment in which the nodules are most abundant is at depths between 4,000 m and 6,000 m in areas of low sedimentation rate. Hydrogenous nodules commonly grow on siliceous and pelagic clay sediment, they are less common on other types of sediment."

Sep 1, 2014

By A. Korchevisky

Environmental self-monitoring is one of the advanced approaches for industrial sustainability programs. Organization for Economy Cooperation and Development (OECD) defines self-monitoring as ?the system of organizational and technical measures put in place and financed by [the] regulated subject? in order to ensure their compliance with regulatory requirements?1. Self-monitoring is beneficial for industrial operators, communities, and governments. Industrial companies use self-monitoring as a central element of their compliance management that allows them to fulfill their duties, obligations, and to avoid citations. When industries control their emissions and ensure workers are not exposed above the regulated limits, communities are better. It is impossible for an EPA, OSHA, or MSHA inspectors to be close to every emission source or workplace full-time. It is much more effective for industries to self-monitor, under due supervision. Occupational conditions are a very important part of industry and health and safety self-monitoring should be highly prioritized. In this paper we will research the regulatory basis and best practice of occupational self-monitoring. We will show that not only is self-monitoring a vital element of an occupational health & safety management system, but that you need a management system for affective monitoring.

Jan 1, 2012

By Donald E. Garrett

Sodium sulfate is one of the larger tonnage industrial minerals. A little more than half of this tonnage — 3 Mt/a (3.3 million stpy) of natural product— is recovered from ore deposits. Most of the rest is produced as a byproduct from other manufacturing operations. Sodium sulfate is mined in a variety of ways. These include conventional room-and-pillar mining, strip mining, in situ leaching of thick ore beds, solar evaporation and cooling-crystallization of lake brine, and the pumping of brine from complex salt deposits. There is also a variety of commercial sodium sulfate ore sources. They include thenardite (the mineral form of sodium sulfate, or Na2SO4), mirabilite (glauber salt,Na2SO4•10H2O), glauberite (Na2SO4•CaSO4), astra-kanite (bloedite; Na2SO4•MgSO4•4H2O), burkeite(2Na2SO4•Na2CO3), sodium sulfate-containing caliche and various brines.

Jan 1, 2002

By John E. Shively, Tracy K. Lundin, Francis Fong

The Superconducting Super Collider (SSC) features two 20 TeV counter rotating proton beams which will be housed in 87 km (54 miles) of tunnel. Four additional lower energy particle accelerators will be housed in 26 km (16 miles) of tunnel and underground structures. Physics experiments will be conducted in two underground detector halls approximately 67 m (220 feet) deep with footprints measuring about 30 m (100 feet) by 100 m (330 feet). Definition and design of underground facilities is advanced with construction of approximately one-third of the SSC program underway. This paper presents an overview and status of the SSC project.

Jan 1, 1993

By A. Martin

Detailed porewater profiles of arsenic and other interstitial metabolites were used to assess the relationship between trophic status, sediment redox chemistry and arsenic mobility in a historic tailings repository. The results demonstrate that in eutrophied systems which exhibit greater sediment oxygen demand, the depth of the Fe(III) redoxcline, and hence depth of arsenic release, may lie in close proximity to the sediment-water interface. As a result, arsenic scavenging mechanisms are significantly reduced, resulting in a greater flux of arsenic to the water column. Such considerations have important implications for the management of pit lakes, tailings ponds and contaminated lakes which may consider: 1) the discharge of sewage to the water body during operations; and/or 2) post-closure fertilization as a remediation strategy.

Jan 1, 2002

By N. I. Aziz, I. Tague, P. Mackenzie-Wood

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Feb 24, 1997

By Badiozamani Khosrow

Introduction The mining industry has been using computers since the late 1950s. Despite this early start, the use of mine planning software is not a common practice in many operations. But the trend might be changing because of the availability of relatively inexpensive personal computers (PC). The introduction of these machines has generated unprecedented interest by mine managers to computerize their planning operations. However, some managers have become disappointed with the PC's lack of adequate software and the inability to handle the massive amounts of information required for modeling. This paper is an attempt to shed some light on the future of computers in the mining industry. It will examine: • historical progress in the computer industry, • future advances in the computer industry, • historical usage of computers in mining, and • future alternatives available to mining. Historical Progress The computer industry has come a long way since the first full-fledged electronic digital computer Electronic Numerical Integrator And Calculator (ENIAC) was built in 1946. This machine weighed more than 27 t (30 st). It contained 19,000 vacuum tubes, occupied 139 m2 (1500 sq ft), and could perform 5000 additions per second. By contrast, today's fastest, commercially available computer is the CRAY-X. It weighs less than 5 t (6 st), has no vacuum tubes, occupies less than 9 m2 (100 sq ft), and performs over 100 million operations per second. This is an incredible advancement in less than 40 years. One person commented on the rate of advancement in the computer industry. He suggested that if the auto industry had advanced at the same rate as the electronics industry, we could buy a Rolls Royce for $2.75 and it would run

Jan 9, 1984

By C. R. Copeland

Airborne dust emission standards are receiving growing attention. This trend is motivated by significant health studies that have shown adverse health effects due to exposure to dust. Currently, the air quality standards are not specific to particles in the nanoparticulate range (<1,000 nm). However, as our understanding of health related matters increases, it is very likely that nanoparticulate standards will be adopted. It was previously believed that typical comminution and material-handling practices could not result in airborne nanoparticulates. However, experimental studies using air monitoring and SEM have verified the presence of nanoparticulates in the air as a result of comminution and material handling. This means that emerging nanoparticulate air quality standards are a real possibility for industrial operations. With this emerging problem facing the minerals industry, effective suppression methods for nanoparticulates should be explored. Systematic studies have indicated that nanoparticulates from silica can be suppressed utilizing hygroscopic reagents such as calcium chloride. This reagent was as much as 93% more effective than water in suppressing silica nanoparticulates.

Jan 1, 2007

By J. F. Lupo

Leaching operations combine both metallurgical and hydraulic processes to extract metals from the ore heap. In the design of leaching operations, metallurgical tests and simple hydraulic tests are often conducted to define operational parameters such as leach cycle time, application rate, lift height, and effective leach area. While metallurgical constraints are often the primary focus on leach facility design, the hydraulic factors are also critical to the overall success of the operation. Some of the hydraulic factors that are known to impact solution flow through heaps include: • Ore physical and hydraulic properties, • Variation in ore properties under heap loading, • Ore mineralogy and its susceptibility to chemical and/or mechanical degradation, and • Heterogeneities within the heap. This paper presents a discussion on hydraulic factors that may impact the effectiveness of leaching operations. In addition, methods are presented which may be used to assess flow conditions within active and inactive heaps.

Jan 1, 2000

By A. Wahab Khair, John G. Oldsen, John C. Stankus, Song Guo

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews, the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Feb 24, 1997

By Peter N. Calder, J. L. Workman

There are many opportunities for computers to assist in dragline mine planning. Three important areas particularly lend themselves to computer assisted study. These are overall mine design and planning, the computation and display of range diagrams and the calculation of production and production variability. The computation of range diagrams is of particular interest because of the importance of matching the dragline and site geometries. This paper examines the uses of range diagrams in dragline mining and illustrates the application of computer techniques to the computation using one such program as an example. The use of computer generated range diagrams for machine selection, pit design and in parameter analysis is discussed. Directions for further development are also provided. There is a great deal that can be done to additionally enhance the ability to provide accurate designs for the dragline operation. One area that needs special attention is the dumping of overburden around access ramps into the pit. This situation is one of the most difficult dumping sequences and affects machine selection and pit operation. It is also suggested that programs that simulate the production schedule of the drag-line would be useful. It is concluded that large overall mine planning programs are very important in dragline mining. However, smaller programs designed for a specific, task are also important tools in many cases. These are easy to learn and use, well adapted to the PC environment and provide useful information, both for design and for daily planning.

Jan 1, 1989