Search Documents

By William F. Lawrence

Within ten to fifteen years, coal-fired power generating stations will be producing over 40 million tons of coal-ash annually in the United States. The largest part of this ash will be emitted from the boilers, entrained in the off-gas stream and trapped as flyash. However, about 15 percent (six million tons) will he removed from furnace bottoms as bottom ash or molten coal-ash slag. In current practice, the molten coal-ash slap is generally water quenched and then transported either as a slurry or in granular form to storage or disposal areas. Although a small amount of this slag is marketed as abrasive grit or as roofing granules, most of it is considered a waste material which must be disposed of at considerable cost to the power companies and therefore to the public. The accom¬panying economic loss in terms of unused raw materials and displaced land is not as obvious but is just as real. The Coal Research Bureau at West Virginia University under the sponsorship of the U. S. Bureau of Mines has been examining the possible utilization of both coal-ash slag and flyash in the mineral wool industry as a method of partially alleviating the growing national problem of solid waste disposal. The potential marketing situation for mineral wool manufactured from coal-ash is illustrated in Figure 1. This bar graph depicts the growth in value of mineral wool shipments1 from 1949 through 1966. In this 17-year period, the value in¬creased by over 350 percent, more than 20 percent per year, despite a decrease in unit cost of mineral wool. It therefore appears likely that coal-ash could find a steady market as a supplement to existing sources of raw materials for mineral wool production.

Jan 1, 1970

By J. W. Powell

Several years prior to 1962, it became obvious that in order to develop ore reserves below the Storke Level, it would be necessary to devise a method to facilitate the ore being lifted three hundred feet to the surface or six hundred feet to the mill. The final plans called for an underground crusher complex with two stages of crushing and a conveyor belt gallery for transport of the ore six hundred feet above, to the third crushing stage. Access into the area was gained in 1962, by sinking Five Shaft approximately one quarter mile southwest of the proposed complex site, and drifting into the area. Collar elevation of Five Shaft is three hundred feet above the 600 Level Crusher Complex. All muck was loaded into ten-ton granby cars, hoisted to the surface and dumped. (See Figure 1 for the relationship between Five Shaft and the Crusher Area) Drifting into the Crusher Area contunued until 1965 at which time the Crusher Room Cutout was started. The Crusher Access Drift (CAD on Figure 2) war driven and mining pm- ceeded according to the description on drawings marked Figure 3a and 3b. After the arch portion of the Cutout was excavated and concreted, removal of the center "pillar" commenced. This muck was removed with an Eimco 123C crawler-mounted front-end loader. (See Figure 4) A total of 576,000 cubic feet of rock was removed from the Crusher Cutout. All sup- port was afforded by grouted roofbolts on a specified pattern, as shown in Figure 3c. Crane support columns were put into place and held by braces welded to roofbolt heads. Sidewalls and endwalls were formed and concreted. (See Figure 5 for the finished product)

Jan 1, 1970

By J. D. Mc Beth

The Carlin Gold Mining Company, a wholly owned subsidiary of Newmont Mining Corporation has been successfully operating an open pit gold mine and cyanide mill for approximately the past ten years. It is a unique operation in that about 20 percent of the mill feed is a carbonaceous ore refractory to cyanidation that must undergo a pretreatment stage developed for, and by, Carlin. The mine and plant are located in the Tuscarora mountain range is north-eastern Nevada near the towns of Carlin and Elko. Claims were staked at the minesite in 1961 and 1962. A drilling program was initiated late in 1962 and after drilling a total of 250,000 feet of rotary drill holes an estimated 9,300,000 tons of ore at a grade of 0.32 ounces of gold per ton was delineated.

Jan 1, 1975

By Hugh Jones

Mine planners are challenged to hold two seemingly opposing objectives: maximizing the mine?s operational efficiency while minimizing post-closure impacts. One of the most effective approaches to meet these objectives is to plan for mine closure from the start. Mine closure is typically viewed as the process that happens in the period of time when the operational stage of a mine is ending and the final decommissioning and mine rehabilitation is being undertaken. In reality, it is a continuous series of activities that begins with preplanning prior to the project?s design and construction and ends when long-term site stability is achieved and a self-sustaining ecosystem is established. Putting this model into practice as early as possible can significantly reduce the financial burden of mine closure and rehabilitation.

Jan 1, 2011

By N. Finkelstein, C. G. Palagi, S. S. Stillar

The C. E. Weed concentrator treats 51,000 tons per day of 0.5% to 0.7% copper ore received from the Berkeley Pit, the Continental East Pit and the Butte underground mines. Improved operating techniques and conversion from semi-autogenous secondary grinding to ball milling have increased tonnage from an original design of 42,000 tpd. Separate treatment of sands and slimes, with recovery of soluble cop- per from the slimes, has increased total copper recovery. Concentrator tailings are pumped 600 vertical feet and 20,000 horizontal feet for disposal.

Jan 1, 1976

By A. W. Swanson

Iron carbide, containing 93.3% Fe and 6.7% C, is a tailor made feed for the electric arc furnace (EAF) and has recently gained worldwide attention as a possible replacement for premium quality scrap. With 38% of the steel in the United States being produced in EAFs, iron ore producers have an interest in becoming direct suppliers to the EAF industry. This paper explains the advantages of using iron carbide in an EAF and describes test work on the product and development work being per formed on engineering designs for a commercial plant.

Jan 1, 1994

By R. Krishna, L. A. Kumar

The paper suggests a new empirical model for predicting mining subsidence. The parameters considered are Lithological Factor, which in this context meant percentage of sandstone, Rock Mass Factor (depending upon the RQD value of drill-hole cores), width: depth ratio and percentage extraction of coal. More than 250 drill-hole cores from seven longwall panels and 11 bord-and pillar (room-and-pillar) workings were analyzed from an extensive data bank of Singareni Collieries Company Ltd. (S.C.Co.), Andhra Pradesh, India. Excellent subsidence agreement was found with the suggested model.

Jan 1, 1993

Mining steeply dipping coal seams is a difficult task. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more, but still limited, progress on mining such seams than other major coal-mining countries. In the last two decades, accelerated research efforts have tried to improve the mining technology in steeply dipping coal seams. Based on this work, a dynamic model of a roof-support-floor (R-S-F) system under asymmetrical constraints in mining steep seams is established here, and a theory of strata control and hazard prevention is formed. The key technologies for mining steep coal seams include global and regional strata control methods in the longwall face; methods for the longwall face machines to sustain static and dynamic loads; and flexible protection technology. These theories and technologies have been successfully applied in China to the mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with a high potential for spontaneous combustion. In recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2013

By K. Tokutake

Kobe Steel, Ltd. improved the quality of iron ore pellets for blast furnace burdens when it enlarged its blast furnaces. However. there still remained room to increase reducibility at high temperatures for better blast furnace operation. In particular, it was still necessary to lessen the reduction retardation above 1200?C. In the last few years, by employing iron ore and additives of optimum size structure, large pore pellets with a high porosity have been obtained. By using this method. Kobe Steel. Ltd. has accomplished the technology to produce pellets with remarkably high reducibility.

Jan 1, 1989

By Edward L. Vickers

When I was originally asked to give this talk, I had certain preconceived ideas of the mining industry's reaction to Operations Research. It seemed at the time to be a rather simple task to collect these ideas for presentation here today. Jotting down these notions, I became concerned that overexposure to this activity called OR perhaps had clouded my outlook on what was actually being done on a nation-wide scale. I felt, to have a better cross section, a questionnaire of current industrial activity was in order. I solicited the response of some 75 mining companies varying in sizes and operating characteristics, and I am pleased to report that the response was good. I received answers from 51. The questionnaire was intended to measure the degree to which their concerns were actually engaged in OR efforts. With all due respect to the people who were so gracious as to answer the questionnaire, I feel that there is a tremendous misconception as to the designed purpose of OR. This is not to imply that there are no active OR groups in the mining industry. But by in large, the majority of the companies sampled appear to be somewhat confused as to what OR really is.

Jan 1, 1962

By EDER DOMINGOS OLIVEIRA, Leandro Viana Teixeira, Carlos Antonio Morais, Ruberlan Gomes Silva

Special attention must be considered in the production of high-grade rare earth products, such as mixed rare earth oxalates or carbonates. In the main minerals used industrially, the rare earth elements (REEs) are finely associated with impurities like calcium (Ca), magnesium (Mg), manganese (Mn), iron (Fe), aluminum (Al), thorium (Th), uranium (U) and phosphorus (P). Most of these impurities must be removed to avoid losses of rare earth oxides (REOs) as well as to prevent product quality degradation and low operational performance in the downstream steps of solvent extraction or ion exchange. The present study aims at investigating the conditions required to precipitate REEs, either as rare earth oxalates or carbonates, from purified rare earth sulfuric liquor with low Al3+ and UO22+ concentrations and very high Ca2+, Mg2+, Mn2+, and SO42− impurity contents.

By Erle I. Shobert

In the comparison and consideration of synthetic and natural materials, graphites represent a situation in which natural graphites amount to less than 10% of the total carbon and graphite production by weight, and less than 5% in dollar volume, There are few applications where it could not be re- placed by synthetic graphite. On the contrary, synthetic graphite materials can be engineered to cover an extremely wide range of applications. These include electrographite brushes for rotating machinery, pyrolytic graphite, graphite-impervious pipe, nuclear moderators, high purity spectrographic graphite, power tube anodes, graphite rotary shaft seals, and rocket nozzles. The special qualities of natural graphite and its limitations are delineated and the almost unlimited possibilities in artificial graphite materials are discussed.

Jan 1, 1964

By John L. Ellenberger

Virtually no two mines operate with the same geographic, geologic, and mining conditions. It follows chat problems vary with the conditions from mine to mine or often from one section to another in the same mine. Actual situations are described, and a technique of "stacking" maps to predict hazards is presented. Two case histories of the use of multiple overlays are de- scribed. The first deals with a property that was examined before the start of mining. The second is a property in which severe ground control problems were encountered and the relationship between the problem areas and known conditions were found to be related.

Jan 1, 1981

The following errors were inadvertently included in "How millisecond delay periods may enhance or reduce blast vibration effects" by R.M. Wheeler in the September issue of Mining Engineering.

Jan 1, 1987

By Jozef Stachulak

Prof. H. Bystron: "An Application of the First Law of Thermodynamics to Winter Dry Air Flow in Mr. Stachulak's Mine Model". [ ]

Jan 1, 1980

By Thomas Bubanovich

Engineers at the Freeman United Coal Min¬ing Company, located in West Frankfort, Illinois, have been using a computerized production planning and maintenance reporting system, which have been designed exclusively for underground coal mining. This paper will explain a dynamic graphical simulation and computerized time study system that has been used to design and evaluate underground production systems for optimizing productivity. Also with the aid of customized software, detailed records on changeable components of underground equipment, including the vendor's name, date installed, operating and maintenance hours, etc., have helped Management to select the best available components for their equipment. The MPASS System, Mine Performance Analysis Simulation System, developed through a cooperative agreement with Freeman United, Ketron Inc., and the U. S. Department of Energy utilizes new methods to analyze and design production systems in underground coal mines. The MPASS System is a menu-driven user oriented system of interactive computer programs, which form five major subsystems. The subsystems: 1. Simulation 2. Time Study 3. Mine Background Reports 4. File Maintenance Subsystem 5. Statistical Analysis Subsystem

Jan 1, 1987

An insufficient hydrologic data base exists for most large and small coal basins in Alaska owing to the lack of need in the past to collect data. The runoff process is insufficiently understood which is complicated by specifically northern phenomenon, and the lack of understanding of hydrologic relationships in permafrost environment. This paper presents an understanding of the hydrologic effects of frozen ground and presents methods by which the influence of surface mining upon the hydrologic balance can be analyzed.

Jan 1, 1988

By A. Jennings, J. Cornet, P. Perrone

Controlling long overland conveyors with multiple drive stations is a complex problem. The methods for controlling these belts in a steady state are well-covered in existing literature, but a discussion of starting and stopping strategies is absent. This paper outlines different control strategies for starting, stopping and running conveyors with multiple drive stations. To illustrate the benefits of applying the methods described in this paper, the authors show how their adoption corrected many of the control system problems at Essroc Cement’s overland conveyor, which features three drive stations separated from each other by long lengths of continuous conveyor belt.

Jan 1, 2013

By S. S. Huyett

The opportunity to cooperate with the Mining Department of the Pennsylvania State University in their Student-Trainee Program is accepted by The New Jersey Zinc Company who believes that the participation in this type of a program will lead to a larger supply of high calibre engineers in mining. Trainees compete with other employees to earn the cost of their education while gaining practical experience in the mining industry. The practical experience is arranged to complement the technical education through a variety of work assignments. Job opportunities for the trainee are related to the work requirements of the Company and to the performance of the trainee. Management must consider and deal with a good many problems uncommon with regular, full 'time employees. For a number of reasons this program is recommended to other companies as a means to encourage outstanding young men who are interested in a career in the mineral industry to obtain a professiona1 education.

Jan 1, 1963

By Ulrich O. Lange

Coal is America's most abundant energy resource. Therefore, it IS logical to assume that coal must be produced in much greater quantifies in order to make the United States self-sufficient, as far as energy is concerned by 1985. However, there are a number of obstacles which have to be overcome in order to achieve such a great task. According to one of the most outspoken American Mining men, there are three major obstacles. Those are: (1 ) Mining technology (2) Public image of the coal mining industry (3) Governmental policy toward the mining industry The following will be dealing with Shortwall Mining, which is a very specific part of mining technology and which might influence the image of the coal mining industry as well as the governmental guidelines, at least to make it easier to live with those guidelines. During recent years the operation of coal mines has been more expensive than ever. Since 1970, the cost of producing coal increased by 30% and the productivity dropped by just about the same amount. Those are alarming signs.

Jan 1, 1975