Search Documents

By G. T. Newell, J. G. Stone, V. M. Mejia

Introduction Advances in drilling have reached a point where large diameter cores can be recovered from "tight," or weakly indurated placer gravels. In such ground, core drilling can provide more reliable data regarding tenor than can be obtained using churn drilling or similar classical techniques. It can also provide metallurgical and geological information that is not available from samples obtained through alternate methods. In 1985, Coastal Mining Co, a subsidiary of M. A. Hanna, and Western Gold Reserves began to review a Tertiary placer deposit owned by San Juan Gold at North Columbia, CA, about 14 km (9 miles) northeast of Grass Valley. The deposit is one of the largest remaining unmined portions of the formerly extensive early Tertiary ancestral Yuba river system. It has been known since the 1850s, has been the subject of much technical literature, and has been the object of at least four previous drilling programs. The eastern one-third of the 6 km (3.7 mile) stretch of the channel between North Columbia and Badger Hill was partially stripped by large scale hydraulic mining in the late 1870s and early 1880s. Mining ceased in 1884 when the Sawyer Decision prohibited further discharge of hydraulic tailings into the Sacramento and San Joaquin Rivers. By that time, about 30 to 45 m (100 to 150 ft) of relatively low grade upper gravels had been removed over some 81 hm2 (200 acres). About 90 to 105 m (300 to 350 ft) of higher grade middle and lower gravels were left at least partially stripped. In 1914, a few churn holes were drilled along a widely-spaced line. In 1938-1939, Selection Trust conducted an extensive drilling campaign to evaluate the deposit. Particular attention was directed toward the partially stripped eastern portion. In 1968, the US Geological Survey drilled three churn holes in the eastern part of the deposit. The US Bureau of Mines conducted experimental mining and drilling in the Badger Hill area. In the late 1970s, Placer Service Corp. acquired a lease on the deposit. Between 1979 and 1984, Placer Service drilled 28 large diameter BADE (a German-manufactured machine) drill holes on the eastern portion of the deposit. The surviving records from the widely-spaced 1914 drilling program are fragmentary and the reported grade not well substantiated. The 1968 holes were drilled for scientific purposes. Again, drilling details are not available. However, detailed records for both the churn drilling program and the BADE program were available and formed the basis for the initial evaluation of the property. Geology The geology of the auriferous Tertiary gravels of California have been described by Whitney (1880), Lingren (1911), and, more recently, Yeend (1974). In general, the Tertiary gravels in the North Columbia area occupy a broad channel cut into pre-Tertiary igneous and metamorphic rocks. The upper, or white gravel is overlain conformably by volcanic tuffs and volcaniclastic rocks. A middle gravel is characterized by the presence of silicified and carbonized wood. A lower blue gravel unit has relatively coarser cobbles and contains a higher proportion of igneous and metamorphic cobbles than the other units. The upper gravel consists of interbedded pebbly sand and silty, or clayey sands with prominent cross bedding. Most of the pebbles are well rounded and consist mostly of white vein quartz and quartzite. The upper unit is moderately well compacted. Exposures in the walls of the old hydraulic mine pits stand at 45° and 50° angles. The gold content of the unit is well below an economic cutoff. The middle gravel - included with the upper unit by Yeend (1974) - is coarser grained, with carbonized wood, and 75 to 100 mm (3 to 4 in.) cobbles of metased-imentary and metavolcanic rocks in a sandy matrix containing abundant lithic fragments. The upper contact appears to be conformable, but the lower portion of the unit appears in places to consist of reworked lower gravels. The unit contains less clay than the upper unit and is somewhat more friable than the underlying lower gravels. The gold content, while somewhat higher than the upper level, is too low to be of ore grade. The lower gravel averages between 30 to 45 m (100 to 150 ft)

Jan 9, 1988

By Greg Joachims

Composition of salt in the Permian Flowerpot Shale in northwest Oklahoma suggests that the salt in this formation was deposited in the early phase of solar evaporation. Brine produced through natural dissolution of the subsurface salt has netted very pure brines, with relatively low concentrations of magnesium salts that should result from late-stage precipitation of salt deposits from sea water. Over the last 100 years, extensive studies of sea- water evaporites, in relation to brine density, have been a topic of discussion. The development of evaporation models has facilitated the increased production and purity of solar salt (salt produced through evaporation of brine by the sun's energy). Conversely, this information can be utilized to gain an understanding of how rock-salt formations were precipitated from sea water by analyzing the elemental constituents of the rock salt and of the resulting brine. By evaluation of well-documented, phase-curve tables of sea-water evaporation, a basic theory can be formulated on how the Flowerpot salt unit was formed.

Jan 1, 1999

By J. Shibata

Separation of rare earth, especially Nd and Sm, was investigated by batch and column methods with a solvent impregnated resin. The solvent impregnated resin was prepared by impregnation of organo- phosphorous extractant whose trade name was PC-88A into a macro porous resin. The adsorption behavior of rare earth with a solvent impregnated resin in a batch method is the same as that with solvent extraction. In a column method to separate Nd and Sm, the effective separation in both adsorption and elution processes can be attained by setting suitable conditions, such as bed height, flow rate and concentration of eluent. Neodymium which is a lighter rare earth is separated from Sm an adsorption step, while Sm in which is a heavier rare earth is recovered in an elution step. From the integration of breakthrough and elution curves, yield of Nd and Sm is calculated in the condition of 100% purity. It was found from the results of life test of the resin that the solvent impregnated resin can be repeatedly utilized at least 20 times.

Jan 1, 1995

By J. K. Mohanty, D. Panda, P. K. Sahoo, R. K. Paramguru, K. C. Nathsarma

Ferromanganese slag, a product of the manganese industry, was characterized mineralogically. The slag, which contains high Mn values, was characterized using optical microscopy, XRD analysis and electron microscopy. No separate Mn-bearing oxide mineral phase was found. The slag is amorphous, and no crystalline phase was identified in the hulk sample by XRD, However, in. fine fractions, quartz was identified. Scanning electron microscopy (SEM) revealed the presence of Mn, Si, Al and Ca in the matrix without the development of a mineral phase. Leaching experiments using H2SO4 were carried out to determine if Mn could be extracted from the slag. At room temperature, almost 100% of the manganese could be dissolved at a solid-liquid ratio o f 1:10 by leaching with dilute sulfuric acid. The impurities could be precipitated by pH adjustment to produce a manganese sulfate solution suitable for the production of MnO2 or electrolytic Mn metal. Based on the laboratory-scale experiments, a suitable process is proposed to recover manganese values from the, ferromanganese slag.

Jan 1, 1999

By Myron W. Mellor

Much has been published concerning the subject of coal preparation as related to electric power generation however it is always a most vital topic for both utilities and coal producers, It also constitutes a field of study that is never finished since new concepts and changing demands continually require altered perspectives. One graphic illustration that has been used to emphasize the rapidity with which times are changing is the fact that during World War I, a station that consumed 1000 tons per day was looked upon as a large central station, while today some single generators require 1500 tons during the same period, For further emphasis, at that time a 20,000 horsepower turbo-generator was a mighty large machine; today, a unit of this size is planned for driving the boiler water feed pump required for a single large main unit. During the past ten years alone, electric utilities have more than doubled their percentage of coal consumed as compared to the total market. They now account for approximately 40% of the United States consumption and one-third of all production including export, Conversely, approximately 70% of all U. S. steam electric generation is by coal and this percentage is expected to increase. It is further predicted that utility consumption will increase from the current 160,000,000 tons per year to between 400 and 500 million tons in 1975 which is approximately equal to todays total production

Jan 1, 1959

By Elza Burch

Introduction The feeding to zero concept involves feeding 600 µm x 0 (28 mesh x 0) size raw coal to heavy media (magnetite) cyclones along with the +600 µm (+28 mesh) size coal. Traditional circuits employ desliming or removing the 600 µm x 0 (28 mesh x 0) size fraction and feeding the cyclones +600 µm (+28 mesh) size coal. The feeding to zero concept recirculates 600 µm x 0 (28 mesh x 0) fines in the circuit. At the same time, a portion of the fine material is continuously withdrawn and recovered. This, in turn, prevents a fines buildup. This concept eliminates desliming screens and secondary fines circuitry for recovery of 600 x 150 µm (28 mesh x 100 mesh) coal. The result is a very simple circuit. Feeding to zero at Island Creek Island Creek Corp. was the first involved with the new concept in 1976. The company needed a temporary plant for the 9.5 mm x 0 (0.4 in. x 0) raw coal at its Pond Fork mine, near Madison, WV, while a full-scale plant was being designed and built. At that time, the Childress Corp., of Beckley, WV, became interested in the feeding to zero concept. Island Creek awarded a contract to Childress to build a single cyclone modular plant, incorporating this feeding to zero concept. The plant was erected in three months. The Pond Fork modular plant proved successful in attaining the desired feed rate of about 63.5 t/h (70 stph), while maintaining good separating efficiencies and low magnetite consumption rates. The 9.5 mm x 150 µm (0.4 in. x 100 mesh) clean coal was recovered and the 150 µm x 0 (100 mesh x 0) size was disposed of to waste. The full-scale plant was completed about two years later and the Pond Fork modular plant was moved to Holden, WV. There, it was incorporated into the Holden 29 preparation plant as a separate circuit for cleaning -25 mm (-1 in.) coal. In 1976, a similar plant was installed in Virginia by another company. These two plants are believed to be the first two operational plants in the United States incorporating the feeding to zero concept. Island Creek subsequently contracted with Childress for an identical plant at the Coal Mountain operation in West Virginia. The plant operated for three years before the mine was closed. The unit was then moved to the Spurlock mine near Martin, KY where it continues to operate. The successful operation of the Pond Fork and Coal Mountain plants before and after relocation proved both the performance and moveability of this type of circuit when constructed in a modular fashion. Since the first two plants were built, Island Creek has incorporated the feeding to zero circuit in nine additional plants. A grand total of 33 cyclones have been installed using this concept. One is the Providence mine, near Providence. Providence preparation plant Island Creek contracted with J.O. Lively Corp. of Glen White, WV in July 1978 for the construction of the Providence preparation plant. The plant began operation in February 1979. The construction period was about halved by building the plant with modular design concepts. Prefabricated sections, floors, and sides were brought in as units and then bolted in place. The Providence plant has a good track record of processing coal at a feed rate of 454 kt/h (500 stph). Feed coal to the plant has an average ash content of about 18% and sulfur content of about 4.5%. It contains about 22% refuse. The coal product has an average ash content of about 8% and sulfur content is about 3%. Raw West Kentucky No. 9 seam coal is conveyed from a box cut in the Providence mine to a rotary breaker. The breaker is fitted with 74 mm-diam (3 in.-diam) opening breaker plates. Therefore, it is well suited for removing trash, roof bolts, wood, and pyritic balls that are common in Illinois Basin coal. The -75 mm (-3 in.) coal is conveyed from the rotary breaker to

Jan 8, 1987

By C. C. Nolan

As the size of the mills get larger and the liners get heavier, a better means had to be found to handle liner replacement. McLellan Industries is famous for their innovative ideas and was called upon by an engineering company to develop a mill liner crane. The first crane was developed for Similkameen about 1969 to serve a 32' 0 x 14' Long SAG Mill. The next was Island Copper in Port Hardy, B.c., the same size as Similkameen in 1970. At that time, we took existing hydraulic cranes and modified them to meet the mill configuration. In 1973, we developed a completely new approach for the Southern Peru copper mine at Tacna, Peru for a Ball Mill, size 16'-6" 0 X 19' Long. Each installation required a design study to meet the change in mill size, trunnion size, elevation of floor to feed trunnion, area at the feed or discharge end of the mill. We have supplied self-propelled units as well as lift in. When there is no room at the feed end and if the mill has a trunnion overflow discharge, we have the mill supplier provide a structural frame to span the sump and move the mill liner handier into position with the use of the overhead crane or a mobile crane.

Jan 1, 1999

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, despite its natural abundance, demand for coal exceeds its countrywide supply due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98 percent of total raw coal production in the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an environmentally friendly manner, especially in populated areas adjacent to the mining zone. This technology eliminates blast hole drilling, blasting and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks.

May 1, 2023

By John A. Dunn

The history of underground coal mining has developed through the years from a manual digging and loading process to the highly mechanized pro- cess that it is today through the use of electric power. Mine power systems have closely followed the continued pattern of improvement and mechanization, through necessity and the application of technological advances, At the beginning electric power used in coal mines was confined to haulage. Since d-c power was better suited to traction drives, mine power systems naturally developed using direct current. During this development, a number of street railway systems were in service, using 550 volts, and it was natural that mine trolley systems went in at 550 volts. As machines for mining operations developed and the number of operating mines increased, a safety hazard developed through the use of 550 volts. Most regulating agencies opposed the use of 550 volts, and after a time the maximum voltage permitted was limited to 300 volts hot line to ground. Up until this time most mines had operated with one central generating station, which served utilization power to the whole mine. Power demands were not very great and transmission losses were within reasonable limits.

Jan 1, 1964

By B. R. Waples

The first reaction in organizing a project of magnitude is that it's the same as smaller projects -- just bigger. This is not totally correct. The industry's record of completing big-money jobs on time and within budget is not outstanding. From a personal point of view, my question is: What is the project size at which controls are lost? Is it controls? Is it the number of pieces of equipment? Is it the number of decisions to be made? The slowness of communications? Or is it a combination of all of these? In working on multimillion-dollar jobs, the percentage of overrun seems to be lower or show an underrun when the following basics are followed: 1) Preplanning is intensified 2) Data gathering is complete 3) Approach is optimized 4) Planning is realistically scheduled 5) Changes are minimized 6) Decisions are expedited

Jan 1, 1982

By Enrique Llewellyn

North River Energy Company a previous subsidiary of Republic Steel Corporation commenced development of the Number One Mine in mid-1972. The mine is located in West Alabama and presently employs a total of 632 people. Production capabilities have increased to 1.4 million clean tons of steam coal per year with the newly purchased Longwall System. Washer recovery averages 57 percent. The seam being mined is the Pratt or Corona with an average height of 52 inches and an average cover of 540 feet. The immediate roof is laminated sandstone and the floor is composed of a hard fireclay. Total production out of the mine is provided to Alabama Power Company under a longtime contract.

Jan 1, 1981

By E. Lovera

Social attention to environmental aspects, steadily increasing in European Countries, has been leading to a stricter regulation of many productive activities. Among them, mining and quarrying sectors have been often censured for their potential and real impacts on land and environment. Referring to dimension stone exploitation (also the terms ornamental stone or natural stone are here used as synonymous), quarries are often concentrated in extractive basins, where the resource is localized with suitable quality and quantity: this fact has sometimes raised critical environmental situations. Nevertheless, dimension stone quarrying represents in Europe a traditional and important economical activity, source of wealth and employment. Moreover, many natural stones take on a ?cultural? value and may be considered as ?classic?, as they have been exploited since antiquity and are element of the architectural heritage of many Countries. The sector relevance demands the research of a sustainable balance between social-economical needs and environmental protection. Actually, very restrictive environmental protection policies have led to severe limitations to quarrying activity, but the results do not seem to be completely positive in terms of sustainability: on the one hand, closing-down stone quarrying activities imposes a shrinkage in local, social and economical development; on the other, quarrying activity is pushed towards developing Countries, environmentally un-protected, simply moving and putting off to next future the problem. The challenge of the sustainable development of quarrying sector ? recently explored in the European Commission?s communication ?Promoting sustainable development in the EU non energy extractive industry? (COM-2000-265) ? should be achieved through a positive link between theoretical statements and practical effects: sustainability indicators may be an effective instrument to assess and monitor the environmental performance of the industry. The paper refers to the development of specific ecological criteria and indicators, which can be useful to measure and predict the eco-efficiency of a dimension stone quarry, finally pointing out where improvement efforts have to be focused.

Jan 1, 2003

By F. Heivilin

"Health and Safety problems can make a mineral deposit or a portion of one, an operating plant, or finished product unprofitable or worthless. Therefore they need to be reviewed when reserves are established and yearly thereafter until the deposit is closed down. Health and Safety regulations serve as a guide, but I have always done more frequent checks, when adding new products with different specifications or during times of bad weather and crisis. Water quality and quantity are always in question. Health and Safety are quality of life issues which are at or near the top of priorities for communities, companies, employees, and government bodies. Georgia dropped from one to three in U. S. for business development due to “Quality of Life” issues. Remember crystalline silica is present in nearly all sedimentary and acidic rocks and basic igneous rocks are the perceived home of asbestos. These health issues, any other safety and health issues or perceived issues need to be resolved initially and any time they come up during life of deposit. When handled properly good safety and health programs add to the profitability of a deposit, not to the costs. Daily safety checks in operating plants and mines, and visual check of all drilling core with an eye for changes are a key to successful programs. Both plants I turned around had terrible safety records, too much airborne dust, and maintenance problems resulting in low productivity. In almost every case cost reduction was tied to eliminating maintenance and spillage problems which caused health problems and increased possibility of accidents. Implementation of these safety and health programs around 1970 starting prior to government programs, working with new MSA/MSHA regulations, working to improve the regulations as a president of a state mining organization, and maintain profits was a challenge, but very rewarding. Reducing time to make repairs and work simplification gleaned from observations and employee recommendations learned from making multiple daily inspections resulted in years without lost time accidents at two plants, reduced maintenance and 33-75 % improvement in cost per ton at A. P. Green Refractories Co. Eufaula Calcining Plant 1972-77 and Oil-Dri Ochlocknee plant and mine 1979-82. The Ochlocknee mine worked 1981-2007 without a LTA. The author participated in 16 acquisitions and new plant design projects. All of above reduced costs allowed mining deposits with higher overburden to be used and considered. Thereby increasing reserves considered in all operations."

Jan 1, 2016

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

The semiautogenous grinding (SAG) mill is one of the most important pieces of equipment in the comminution of materials. Its objective is to reduce the size of the ore until the ore can be released and continue on its transformation process. Although it is a simple process that involves impact, abrasion and attrition, its energy consumption is extremely high and inefficient, with no more of 17 percent of the energy supplied going toward size reduction. This gives rise to an important challenge because any improvement generates great economic benefits.

By T. W. Camm, J. C. Johnson

"Most engineers are bright, hard-working, reliable, and prefer to avoid conflict. An engineering curriculum tends to self-select these characteristics. By most standards, you would expect workers exhibiting these traits to require minimal supervision. But is this true? Is this how most current engineering managers lead? Looking at some current theories on leadership combined with personal anecdotes, this presentation will look at some common misconceptions about leading engineers. INTRODUCTION Engineers are different. There, I said it. From cartoons to movies to television shows and more, there is a reason stereotypes of engineers resonate. Yes, you can find a lot individual variation among specific engineers that you may know, but they do not detract from some of the overarching commonalities that engineers are known for. CLASH OF CULTURES What distinguishes a professional? Raelin (1985), in his book Clash of Cultures, describes professionals as having superior intellectual training, maintaining their own standards of excellence, and being supported by associations that maintain the quality of the profession. Engineers obviously fit all three of these ideas: an engineering degree is still regarded as one of the most difficult to attain; we maintain our own standards both through peer-review and in academia through ABET accreditation; and through professional associations like SME to promote the discipline and foster technical growth. Six characteristics representing professional status are described by Raelin (1985, p. 9): Expertise—prolonged specialized training in a body of abstract knowledge. Autonomy—the freedom to choose the means to solving a problem. Commitment—Primary interest is in pursuing the practice of one’s own chosen specialty. Identification—identifying with the profession and with fellow professionals, both through formal associations and through peers external to the organization. Ethics—providing service without concern for oneself or without becoming emotionally involved with the client. Standards—committed to help in policing the conduct of fellow professionals. Engineers are smart—in the vast majority of cases they are hired specifically for their expertise. At a typical mine the ventilation engineer knows more about mine ventilation than anyone else on site; the same is true for the rock mechanics engineer, the explosives engineer, the planning engineer who uses sophisticated computer software—each is the expert for their particular area at the mine, that is why they have that responsibility. This can present a dilemma for the manager for each (sometimes all) of these engineers. The manager needs to keep everyone on task and focused on the objectives of the organization. Because they have reached their position by following the norms and expectations of the organization, managers tend to have a certain amount of loyalty to that organization. Engineers, on the other hand, tend to have mixed loyalties, having as much loyalty and affinity for their profession as they do for the particular company they happen to be working for at any given time. This dynamic can often lead to power struggles between the managers, based on their positional authority in the organization, and the engineers, based on their specialized knowledge (Camm, 2013)."

Jan 1, 2017

By V. P. Petrov

There is a great number of asbestos deposits in the USSR. Some of them are quite large ones. The main deposits of chrysotile asbestos can be seen in the sketch map (fig. 1). Bazhenovo deposit situated in Sverdlovsk region is the largest of them. It is on mining operations since year 1889. Systematical studies of asbestos deposits were begun from the first years of Soviet Government and connected with the names of K.E. Tarasov, P. M. Tatarinov, B. J. Merenkov, N.D. Sobolev, F. V. Syromjatnikov, V. N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V. R. Artemov, V.F. Dybkov and many others. This investigations served the USSR to be one of the most important producers of asbestos in the world. In the limits of the report a characteristic of the main asbestos deposits of the USSR may be done in general outline, from the point of view of their genesis, and in order to show their common features and differences that must be taken into account for forecasting, exploration, and mining of asbestos. All chrysotile asbestos deposits of the USSR were formed of magnesium rock as a result of comparatively lower-grade temperature hydrothermal alteration and free crystallization of fibrous chrysotile in open cavities that served as catalyst As a matter of fact an important mineral for industry is not chrysotile in general, a widely distributed rock-forming mineral, but a long fibrous and mainly vein variety of chrysotile. It must serve for geologists as an important prospecting criteria. A geologist should search for the mineral not only places of possible chrysotile generations, but places where asbestos may be crystallized in its long fibers that could be fiberized well. The Soviet geologists distinguish two groups of chrysotile-asbestos deposits: (1) related to ultrabasic rocks and (2) related to sedimentary dolomite terranes, taking into account what the maternal rock was affected by hydrothermal solutions. The largest deposits related to ultrabasite. The largest deposits in dolomite are small ones but their asbestos contains almost no iron. So much asbestos is a better filler into insulating plastics. There is a few types of asbestos deposits in the limits of the ultrabasic group. The largest of them is a Bazhenovo type which the deposits of Urals are attributed, and Bazhenovo deposits is the first instance. The Bazhenovo type is characterized by the most complete zonality in disposition of various kinds of asbestization. This type of deposits is practically the only one to be in working now in the USSR.

Jan 1, 1978

By Alan M. Ritchie, Paul Miskelly

The 2-D code FIDHELM has been used to simulate conditions in piles of pyritic material with vertical dimensions of 20 to 70 m and a horizontal dimension of 500m. Those properties of the pile and its external environment (wind, temperature) important in determining the time and space dependence of sulfide oxidation, have been identified. A prescription to evaluate the overall sulfide oxidation rate in a pile of known volume but variable geometry has been developed.

Jan 1, 2000

By John J. Mancini

Elastomeric liner products have been used for over two decades in a wide variety of uses including pond liners, hazardous waste barriers, dam face rehabilitation and mining applications. Asphalt blended with polymers is enjoying renewed interest in the engineering community because of its durability, high yield attributes, fewer CQA steps due to seamless installation, and ease of installation and repair. As in other lining technologies, advancements in polymer chemistry and improvements in installation techniques have had dramatic impact on the quality of fluid-applied asphalt (FAA) membranes. Membrane 6, man­ufactured by Deery Oil, Inc. for over 16 years is a hot-applied polymer modified asphalt membrane that can be applied to a variety of substrates in a reinforced configuration or installed directly on an asphalt surface. By blending thermoplastic polymers with asphalt, very favorable stress/strain characteristics can be achieved (Chambers, 1980). Typically the membrane will yield under rel­atively low stress and also exhibit high elongation capability. In service applications where puncture resistance is a concern, fluid applied asphalt materials have the flexibility and com­pressive strength under heavy loading that leach pad designers may find attractive. Additional security is achieved if long term service life is important as in the case of radioactive waste con­tainment. The Department of Energy selected Membrane 6 over seamed liners for a surface barrier that must isolate and contain radioactive waste for 1000 years. Asphalt has a long history of use as a water-stop material and it is believed that this natural construction material combined with SBS polymers will per-form for a millennium. (Freeman, 1994) The process of installing Membrane 6 varies according to job size and the type of surface to be protected. Lining applica­tions on compacted substrates require the membrane to be applied to a scrim cloth (fig 1). Some early pioneers in FAA technology neglected this step and therefore never achieved per­formance levels that satisfied regulatory guidelines. The scrim provides a cohesive surface that promotes membrane flow while achieving high impermeability (2Xl0 '11).

Jan 1, 1996

By R. K. Singhal

A variety of mining equipment is used in the mining of oil sands by surface mining. This includes bucket wheel excavators, draglines, hydraulic shovels and off-highway trucks. This paper examines the existing mining schemes and equipment used Peculiarities of oil sands surface mining and their influence on equipment selection, utilization and mining schemes are described. Recent developments undertaken to improve mine productivity are also dealt with together with some notes on proposed measures to obtain further gains in productivity.

Jan 1, 1985

By Ireneusz Tomza, Jolanta Lebecka

INTRODUCTION Radioactive deposits were observed in 1972 in some of the Upper Silesian coal mines. They were located mainly in the drains in galeries and on the inside surfaces of water pipes. They also caused some problems by accumulating in water pumps. It has been postulated that the deposits are produced by natural radioactive waters seeping from the rocks. Investigations were initiated to answer the following questions: - What is the composition and the amount of radioactivity in the deposits? - What radioisotopes are present in the water? - How are the radioactive deposits formed? - Do the radioactive waters also occur in other mines? - How does the radioactivity of the water depend on chemical composition? - What is the origin of the radioactive water? - Does the water and the deposits cause radiation hazards for miners? -How can the radiation hazard be reduced? METHODS OF MEASUREMENT Determination of Radium Isotopes in Water The commonly used methods of radium determination in water are either based on measurements of the radioactivity of 222Rn which is in equilibrium with 226Ra, or on the detection of alpha particles of the radium radioisotopes after chemical separation of radium from the water sample. The method based on radon activity measurements is very sensitive and does not require any chemical Separation, but it can be used for determination of 226Ra from the uranium series only, because the thorium daughter 220Rn has too short a half-life (55s to yield the required accuracy. The method developed by Goldin, 1961 [2] involved alpha-particle measurements in thin layers of RaS04 and BaS04 separated from the water. This method is not convenient for saline water and water with high barium concentration because the amount of barium carrier in this case is too large to obtain a thin layer of precipitate with sufficient activity. The Upper Silesian carboniferous waters are often saline with high barium content, so the method described by Goldin was not convenient for this case and it was necessary to change the detection system and modify the chemical preparation. The procedure developed by the authors for the determination of radium isotopes in water was as follows: - Depending on the Ba2+ content and the required sensitivity of measurement, a water sample of 200 cm3 to 3 dm3 was taken. - 10 cm3 of 0.25 M citric acid and 5 cm3 15M ammonia was added to form complex Ba2+ ions and avoid the immediate precipitation of BaSO4. (This was repeated as long as the addition of BaC12 did not form a precipitate.) - 1 cm3 of 1N solution of Pb(N03)2 as a carrier for radioactive isotopes of lead and 10 cm3 of 0.1 N BaC12 as a carrier for radium were added. - The sample was heated to the boiling point and the precipitation of RaS04, BaSO4 and PbS04 with 50% H2SO4 was carried out. - After several hours the sample was centrifuged and the precipitate was purified by washing with nitric acid and distilled water. - The precipitate was then redisolved in 20 cm3 0.125 M Na2EDTA and 3 cm3 6M ammonia and reprecipitated from the solution by dropwise addition of acetic acid to d pH of 4.5. At this value of pH, precipitation occurs only for the barium and radium sulfates, while lead and all other radioactive elements remain in the solution. The date and time of deposit precipitation was recorded. - The final barium-radium sulfate mixture was washed with distilled water and transferred to standard measurement vials. - Each vial containing a deposit had 6 cm3 of distilled water added and was then shaken vigorously. 12 cm3 of liquid gelling scintillator (INSTA-GEL UNISOLV-1 type) was then added and the vi 1 was shaken again. After a while the scintillator turns into a milky gel in which the deposit is uniformly distributed. - The standard sample of 226Ra was prepared in the same way. - The activity of the samples was measured using a liquid scintillation spectrometer. (In this case the TRICARB 3320 produced by Packard Instruments, was used). Tests run on standard radium solutions provided by Amersham Radiochemical Centre indicated that this method of measurement enables one to achieve an efficiency of almost 100% (within measurement error). For alpha particles no quenching effect was observed for the BaS04 concentration in the range up to 80 mg of BaS04 per 1 cm3 of liquid scintillator coctail (Fig. 1). This provides a sensitive determination of radium in water with high barium content and also in saline water. In saline water the solubility of barium sulfate is much higher than in

Jan 1, 1981